SPL REPAIR / REPLACEMENT OF OH LT LINE TO UG CABLE LT POLES, STREET LIGHTS, OLD RUSTED GI PIPE LINE OF EXCISE INSPCTOR, STAFF AND CAFETERIA OF THE CSD DEPOT AND SALVAGE STORE AT DIMAPUR UNDER GE 868 EWS 868 EWS

Amount

Dismantling asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings.

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets

Dismantling of frame work timber scantling 40 Sq cm and over in section in any position complete all as specifed and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed.

Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed.

Taking down chowkats or frames with shutters with exc. 1.5 Sqm but n.exc. 4 Sqm each (without taking of shutters from the frames) complete all as specified and as directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each Ditto but with shutters (without taking off shutters from the frames)

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all specified and as directed

S&F Rolled sections as in roof truss, purlins including cleats GDE Fe 410-0-or Fe 310-0.

M & L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete complete .

Material and labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channel and like etc complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred /stopped ends etc complete all as specified and directed.

Material and labour for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, paving, footpath etc and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L 2nd class hard wood, clean sawn, in scantling timber frame and fixed with nails complete all as specifed and directed.

M&L 2nd class hardwood plain, solid, straight chowkats and frames rebated on the solid, rounded or chamfered, put together with glue pinned at joints

Supply and fixing for 35mm 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply and fix 30mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Sec-tion 8, clause 8.24 (a) complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nails

M&L 12mm thick plywood grade BWP type BB fixed with screw to timber frame work complete all as specifed and directed.

M&L for rolled sections as in framing for clazing and the like fixed with angles cleats and connecting plates with timber foer eaves board complete all as specified and as directed.

Supply and fixing 100mm size mild steel butt hinges, medium weight, cold rolled complete all as specified and as directed.

Supply and fixing 75mm size mild steel butt hinges complete all as specified and as directed.

S & F Aluminium anodized, barrel tower bolts, 150mm long of extruded section complete all as specified and as directed.

S & F Aluminium anodized, barrel tower bolts, 100mm long of extruded section complete all as specified and as directed.

Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing for 300mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

Supply and fixing as in replacement mild steel galvanized iron wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 and fixed with tinned tacks or staples complete all as specified and as directed.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) complete all as specifed and as directed.

Material and labour coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed of CM 1:4, complete all as specified and directed by Engineer-in-charge.

Ditto all as per item no 33 above but as in skirting over and including 10mm thick cement plaster in CM (1:4) and ditto

S&F pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified .

S & F Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

Demolition of reed, lathing, single or double, including battens and olaster or chicken wire lathing complate all as specified and as directed.

Supply and fixing 0.71 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc in walls, ceilings, stanchions, beams etc, including all laps cutting and waste complete all as specified and as directed.

Material and labour for rendering 15 mm thick plaster in cm (1:4) with using water proofing compund on one side of lathing finished even and smooth with out using extra cement cpmlete all as specified and as directed.

Material and labour for rendering 15 mm thick plaster in cm (1:6) other side one side of lathing finished even and smooth with out using extra cement cpmlete all as specified and as directed.

Materials and labour for 15 mm thick rendering on brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

M & L rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound @ 3% by wt of cement finished fair faces of brick/concrete surfaces even and fair without using extra cement . The work will be carried out upto tripple storey building the rate of scafolding is included for this item also. WPC will be measured and paid separately.

Supply only integral water proofing compound ( ISI marked )

M&L preparation of newly plastered surfaces of walls & applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified.

M&L for preparation of new plastered surface & applying two coats of oil bound distemper (OBD) over a coat of white chalktening on wall complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

Writing letters or figures with synthetic enamel paint (Block, Roman, Italic or Indian) not exceeding 30cm high over old painted surfaces complete all as specified and as directed

Supply and fixing 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane after and including hacking out broken glass from wooden/metal surfaces complete all as specified and as directed by the Engr-in-Charge. Make : Modifloat/Ashai/Saint Gobain.

Supply and fixed vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

Supply and fixing as 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed. Make: Prayag Cat No : 323 or equivalent approved make.

S & F stainless steel sink, 1mm thick for kitchen with draining board with plug and PVC waste pipe including bedding in cement mortar, fixing brackets overall size 915x460mm, bowl size 410x330x 160mm, as fixed in repairs complete all as specified and directed. (Make: Jayna Cat No SBSD-05 or equivalent approved make of Hindustan/A one//Blue Star/Jayna)

Supply and fix 15mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd.

Supply and fix 20mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd.

Supply & fixing as in replacement 15mm Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing as in replacement for 15mm Stop valves fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engr-in-Charge. Make : Essco Cat No 513A/513B or equivalent aproved make.

Supply and fix as in replacement of 15mm bore pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by the Engr-in-Charge. Make : Essco, Cat No DLX-508 or equivalent approved make

S & F in repairs waste coupling of PTMT (half or full threaded) 32 mm dia ,complete all as specified and as directed.

S & F in repairs waste coupling of PTMT (half or full threaded) 40 mm dia ,complete all as specified and as directed.

S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed.

Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 500 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections complete all as specified and as directed by the Engr-in-Charge. Make : Syntex/Polywell/Polycon

M&L for reinforced cement concrete (nominal mix) 1:2 :4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

S&F TMT MS bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

Dismantling cross arms of MS channel or angles sections flats;nuts bolts washers etc and removing the old materials from the Site(s), complete all as specified and directed

Dismantling of old ACSR conductors or disturbed span including line spacer/separator and keeping serviceable materials in safe custody for re-use and unserviceable materials removing from the Site(s), complete all as specified and as directed.

Dismantling old insulators, any type, any size and keeping serviceable materials in safe custody for re-use and/or unserviceable materials removing from the Site(s), complete all as specified and directed.

Dismantling earth wire of any size/dia or, guarding cradle and removing old materials from the Site(s) complete all as specified and as directed.

Dismantling of LT unserviceable pre-stressed concrete poles of any size and shape and including taking out dismantled portion of poles embeded in ground after necessary demolition of concrete foundation and making good disturbed ground surface properly and disposal thereof as directed by the Engineer-in-Charge.

Excavating in trenches, for foundation of poles, stays or for laying of cables, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and as directed.

All as per item No 72 above but depth exceeding 1.5 metre but n. exc 3.0 metre for foundation of poles etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated material (soil) n.exc.50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and directed.

Supply and laying well burnt bricks, sub class 'B' bricks laid breath wise along length of cable in trenches for cable protection laid for UG cable protection all as specified.

M & L for spread fine river sand cushioning for protection of cable (below, above and around the cable laid in trenchs) all as specified and as directed.

Supply,install, commission and testing cubical type LT panel board of size 1 x 1 x 0.50 mtr,outdoor canopy type, manufactured by a CPRI approved factory, floor mounted, dust & vermin proof,front and rear operated door with necessary locking arrangement made of 50 x 6mm MS angle iron frame work and CRCA sheet of 3.15mm thick duly painted with two coats of powder coated paint of approved shed after seven tank treatment process both internally and externally. The panel shall be suitable for 415 Volts, 50 HZ, 3 Phase 4 wire system and shall be complete with suitable capacity Copper bus bar (1.5 times the incoming switch gear current rating) with suitable size of PVC insulated copper conductor, thimbles glands complete all as specified and directed with the following accessories :- INCOMING (a) MCCB 4 pole, 415 Volts, 160 Amps, 25 KA - 01 No. (b) Indicator lamp (RYB) (set of three) - 01 Set OUTGOING (a) MCB SPN 32 A - 06 Nos.

Supply,install, commission and testing cubical type LT panel board of 0.75x0.75x0.50,outdoor canopy type, manufactured by a CPRI approved factory, floor mounted, dust & vermin proof,front and rear operated door with necessary locking arrangement made of 50 x 6mm MS angle iron frame work and CRCA sheet of 3.15mm thick duly painted with two coats of powder coated paint of approved shed after seven tank treatment process both internally and externally. The panel shall be suitable for 415 Volts, 50 HZ, 3 Phase 4 wire system and shall be complete with suitable capacity Copper bus bar (1.5 times the incoming switch gear current rating) with suitable size of PVC insulated copper conductor, thimbles glands complete all as specified and directed with the following accessories :- INCOMING (a) MCCB 4 pole, 415 Volts, 63Amps, 25 KA - 01 No. (b) Indicator lamp (RYB) (set of three) - 01 Set OUTGOING (a) MCB SPN 40 A - 06 Nos.

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area as required as specifed and directed for the following with suitable lugs :- Make : Havells/Finolex/Richa

10 Sqmm, 2 core

35 Sqmm, 3 1/2 core

50 sqmm, 3 1/2 core

95 sqmm 3 1/2 core

S & F in repairs IP 65 Modular box made of impact resistance plastic & heat resistant materials of size 260x210x116mm mm with provision of bus bar including MCB SP 6 A for street light controlling complete fixed to street light pole with suitable size of clamps, nuts & bolts as directed. (Make : HENSEL/SYNTEX or equivalent model as approved)

Material & Labour for plain cement concrete type B-2 (1:2:4) (with using 40mm graded stone aggregate) as in foundation filling and mass concrete for platform of transformercomplete all as specified & directed.

M & L for plain cement concrete type C1 (1:3:6) (20mm graded stone aggreagate) as in coping of poles including necessary form work complete all as specified and as directed.

Supply & fixing Steel tubular swaged poles complete with cast iron base plate,finial taper plug, bolts, nuts and screws as specified type 410 SP-55(9.0 metres long) including painting of pole with one coat of synthetic enamal and two coat of aluminium paint with numbering on it all as conforming to ASEB specifications, complete all as specified & directed.[Note: Excavation & earthwork, cement concrete, etc. will be measured and paid separately under relevant Items of this Schedule]

S & F LED street light 60 W pressure die cast aluminium housing with IP 66 with all accessories complete including 40 mm dia GI pipe L shape (Approximate 1.5 mtr long) with double clamp and nut bolts. (Make - Bajaj, Cat No - BRTFG 60W LED or equivlant model of make as per list of manufacturer).

M & L for 5 mtr Road cutting/digging for laying of UG Cable and filling, make good with PCC Concrete the disturbed road with complete all as directed by Engr-in-Charge

Supply and laying in trenches steel water tubes light grade galvanised with all fittings in wall / trench complete incl all as specified & directed of sizes 40 mm dia:-

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber with CI cover plate 10mm thick including angle iron frame , funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable

Supply and laying in trenches steel water tubes medium grade galvanised with all fittings in wall / trench complete incl taking down old U/s pipe line all as specified & directed of following sizes:- Note : GI fittings such as union, Tees , bends, nipples, sockets, elbows etc or welding work as required at site will be included in the rate quoted by the contractor.

20 mm dia

25 mm dia

50 mm dia

Supply and fixing of gun metal gate valve Gun-metal, globe valve ,with iron wheel ead, screwed both ends for iron pipe and fixed complete incl taking down old U/s gate valves as specified & directed of following sizes:-

20 mm dia

25 mm dia

50 mm dia

Material & Labour for construction of brick masonry valve pit of internal dimension 0.9M x 0.9M x 0.9M complete with MS angle iron frame work (angle iron size 50mm x 50mm x 6mm) and 3.15 mm thick MS black sheet top cover openable through hinges of suitable size including necessary earth work, PCC, locking arrangement,rendering complete with two coats of black bituminous paint over a coat of red oxide zinc chrome primer to all iron surfaces all as specified and directed.

M & L for boring of holes under road, pavment hard standing by trenches technology ultra sounding technique and necessary machine including HDPE pipe of 150mm dia suitable for 0.4 mpa working pressure.

S&F, in replacement, rotational moulded polythene water storage tank triple /multilayer (Cylindrical vertical with closed top), incliding float valve and connected accesories and fixed in position all as specified in SSR pt-I of the following capacities

500 Ltrs capacity

1000 Ltrs capacity

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked pvc Conduit including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed.Make : Richa/Anchor/Finolex Make is casing caping/Conduit pipe : Presto plast/Supreme/Richa

One light pointcontrolled by one, one way switch .

One Ceiling fan pointcontrolled by one, one way switch .

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the switch socket combination.

One bell/buzzer point controlled by one push button on the same board with other switches or independent

All as per item No- 96 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. .Make : Richa/Anchor/Finolex Make is casing caping/Conduit pipe : Presto plast/Supreme/Richa

M&L for Switch piano flush type single pole, one way 5A Make:-Anchor/Plaza/SSK

M&L for Switch Socket Combination outlet, 2 in 1, 3 pin 5A flush type Make:-Anchor/Plaza/SSK

M&L for Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type Make:-Anchor/Plaza/SSK

M&L for bell push , flush type Amps Make:-Anchor/Plaza/SSK

M&L for Electric Bell , AC 230 volts, single pole Make:-Anchor/Plaza/SSK

M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc.Make:-Anchor/Plaza/SSK

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed.Make:-Anchor/Plaza/SSK

Taking down existing burnt aluminium/ Copper sub main wiring and M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper FRLSH conductors , 1100 volts grade, drawn through and including non metalic rigid PVC Conduit accessories (including concealing and making good to the disturbed surface of wall ceiling floors etc. including making good the disturbed surface and paint touch up to match with the existing surface) complete all as specified and as directed. Note : Three runs of 4.0 Sqmm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length Make :Richa/Anchor/Finolex

M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings incl taking down old unsv light fitting. Make:-Anchor/Plaza/SSK Make LED Lamp : Bajaj/CG/Surya

M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting incl taking down old unsv light fitting complete all as specified and as directed.Make : Havells Cat No LHFXCEP1TNNW020(batten) & LHLDDCXCML8Q020(LED Tube) or equivalent in Bajaj/Philips

M&L for LED 1x20W Security light fitting, drawn through including GI bracket of suitable size light grade 1.4 mtr bend to shape and MS clamps made out of flat iron of size 40x4 mm -02 Nos including nuts, bolts, washer as required and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and directed.Make:-Havells Endurapearl SL20WLLED757SASYTOPCMP /Bajaj/Philips/CG

M&L for TPN DB- VTPN DBs, 415 Volts 4 Way wall mounting inddor type adjustable suitable for incoming 4 pole 100/63 Amps MCCB and out going SP/TP MCBs with suitable for flush mounting and surface mounting with 100 A copper Bus bar for each phase with 2 Neutral bar 2 Earth bar and cable ties for management, reversible Door fot IP 43 & IP 54 DBs taking down old unsv MCCB complete all as specified and as directed. Make : Legrand Cat No 507720 /Havells/ABB/Siemens

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed.Make:- Legrand Cat No 607711 or equivalent in ABB/Siemens

M&L for MCB TPN 63 Amps 25 KA, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make : Legrand Cat No 420043/Havells/ABB/Siemens

M&L for MCB SPN 40 Amps 230 volts 50 HZ suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed.Make:- Legrand Cat No 408636 or equivalent in ABB/Siemens

M&L for MCB SP 5-32 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed.Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

Taking down Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

Taking down Exhaust fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

NAGALAND AGENCIES CO

SAYED ALI AND SONS

SHRI VIKASHE ZHIMOMI

M/S NIYATI NETWORK