REPAIR MAINTENANCE OF PIPELINE PUMPSETS AND CLEANING OF O/H AND UNDERGROUND SUMPS AT KALINA MILITARY STATION, REPAIR MAINTENANCE OF LIGHTNING PROTECTION SYSTEM, SOLAR WATER SYSTEM, FIRE FIGHTING SYSTEM IN DIFFERENT BUILDINGS AND REPAIR MAINTENANCE OF

Amount

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.5 m in depth, for laying of cable etc, not exceeding 10 sqm on plan and getting out in hard/dense soil for exposing of pipe complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layer not exceeding 25cm in soil complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

Supply, fix and jointing steel water tubing of 80mm bore medium grade, galvanised iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

ditto as per item no 04 above but for 50 mm GI bore pipe.

ditto as per item no 04 above but for 40 mm GI bore pipe.

ditto as per item no 04 above but for 25 mm GI bore pipe.

ditto as per item no 04 above but for 20 mm GI bore pipe.

ditto as per item no 04 above but for 15 mm GI bore pipe.

Supply and fix gun metal gate valve of 50mm bore with iron wheel head, screwed both ends for iron pipes & fixed including taking down existing etc complete all as specified and as directed by Engineer-in-Charge for following sizes: Make: Kirloskar / Zoloto / Kartar / Upadhaya / Leader / BIR

ditto as per item no 10 above but for 40 mm GI bore.

ditto as per item no 10 above but for 25 mm GI bore.

Supply, fix, joint and testing Cast Iron Sluice Valve heavy duty of 150mm dia, with stainless steel spindle, PN 1.6 (Flanged) with iron wheel head, hand operated, bronze body seat ring, jointing, coupling both ends for cast iron pipes including nuts, bolts, rubber gaskets etc including taking down old unserviceable Sluice valve complete all as specified and as directed by Engineer-in-charge. Make: Kirloskar / Upadhaya / Leader / Venus / L & T (audco)/ BIR

ditto as per item no 13 above but for 100 mm dia.

ditto as per item no 13 above but for 80 mm dia.

Material and labour for construction of new valve chamber of size 1200mm x 1200mm x 600mm ( Internal size) including necessary excavation and earth work in any type of soil, PCC foundation (1:3:6) type C-2, using 40mm graded stone aggregate as in base concrete 100mm thick, 15cm offset, 230mm thick brick work in CM 1:6 with 10 mm thick rendering internally and 15 mm thick externally in CM 1:4, 50mm thick PCC 1:2:4 type B1 as in coping, 6 mm thick MS cover with hinges and locking arrangement, fixed to angle iron frame made out of 40 x 40 x 6 mm MS angles complete with two coats of synthetic enamel paint over one coat of red zinc chrome primer on all metal surfaces & three coats of white wash on all plastered surfaces of valve chambers including dismantling of unserviceable valve chamber with rusted MS cover without disturbing the existing pipeline etc complete all as specified & directed by Engineer -in-Charge.

ditto as per item no 16 above but of size 900mm x 900mm x 600mm ( Internal size)

Material and labour for desludging / desilting of RCC over head water tank of 50000 Gallons capacity by draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes and high pressure cleaning method with rotary sets with approved detergents and sucking out all dirty water by vacuum cleaners, disinfecting the tank with approved chemical solution for making surface bacteria free and finally cleaning with fresh water to the satisfaction of Engineer - in- Charge including painting MS plates manhole covers, suction pipes, rugs, etc. with two coats of anticorrosive paint and writing outside the tank as TANK CLEANED on_______and capacity _______ on black painted surface including removing all dirt outside land to a distance exceeding 50 mts complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 18 described here-in-before but 25000 Gallons capacity

Material and labour for desludging / desilting of underground sedimentation reservoir of 150000 Gallons capacity by draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes and high pressure cleaning method with rotary sets with approved detergents and sucking out all dirty water by vacuum cleaners, disinfecting the tank with approved chemical solution for making surface bacteria free and finally cleaning with fresh water to the satisfaction of Engineer - in- Charge including painting MS plates manhole covers, suction pipes, rugs, etc. with two coats of anticorrosive paint and writing outside the tank as TANK CLEANED on_______and capacity _______ on black painted surface including removing all dirt outside land to a distance exceeding 50 mts and including surrounding of tank to a distance of 5metre around by removing of all vegetation, bushes, mud, dirt, dust etc and shift to a distance not exceeding 50metre complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 20 described here-in-before but 60000 Gallons capacity

All as per item No. 20 described here-in-before but 50000 Gallons capacity

All as per item No. 20 described here-in-before but 25000 Gallons capacity

All as per item No. 20 described here-in-before but 20000 Gallons capacity

All as per item No. 20 described here-in-before but 10000 Gallons capacity

All as per item No. 20 described here-in-before but 5000 Gallons capacity

Carrying out scheduled maintenance and servicing of all electrto-mechanical machinery of existing centrifugal, submersible, monobloc pump motor and accessories any type, any make and any model in every days or when ordered including cleaning its patrs , removing corrosion , refixing it, rectifying leakage due to loose nut/stud/glang packing/gland rope/ star packing/ clamps/ washers etc of suitable size complete all as specified and as directed by Engineer-in-Charge.

Material and labour for dismantling Monoblock/ Centrifugal electric motor of 415 volts, 40 HP capacity including removing of electric connection from its position carefully and transporting the same to the work shop for rewinding of motor (both stator and rotor) with super enamelled copper wire of same size with existing motor of pump set with insulating materials, varnishing and baking, replacement of worn-out bearings etc as required including re-fixing, connecting with existing electric cable etc., testing & commissioning for satisfactory functioning etc complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 28 described here-in-before but for 20 HP pump set

All as per item No. 28 described here-in-before but for 15 HP pump set

All as per item No. 28 described here-in-before but for 10/12 HP pump set

All as per item No. 28 described here-in-before but for 5/ 7.5 HP pump set

Material and labour for dismantling and disconnecting upto 15 HP 3phase openwell submersible sewage pump from pump house, transporting to contractor's workshop, dismantling and carrying out necessary repairs/replacement of motor as following : (a) Cutting out existing winding of stator of monoblock motor of any make and rewinding with same size of copper winding wire as existing guage.the electric motor and re-assembling the pump set on existing foundation after repair / overhauling of motor including following and testing complete all as specified and as directed by Engineer-in-Charge. (b) Straightening the slot of starter of submersible motor of any make (c) Replacement of thrust washer and bearing complete (d) Replacement of worn out bushes of submersible motor (e) Replacement of sand guard (f) Providing of sleeves in end plate of submersible Pump (g) Replacement of grommet (h) Replacement of water seal (j) Lathe work of motor shaft to bring it to original size and shape and plastering of shaft of submersible motor for smooth functioning on desired amps.

Material and labour for Painting of motor pump base discharge line and suction line complete with all accessories including panel board, scrapping thoroughly existing corroded paint and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.

Supply and fix monoblock centrifugal pump set 3 Phase, 230volts, 5HP, 3.7KW capacity with 80mm suction and 80mm dia delivery having discharge capacity 17.5 litre / second at 30metre head with cast iron / MS base plate etc complete all as specified and as directed by Engineer-in-charge. Make: Kirloskar model KDS-520+ or equivalent to KSB /Jyoti / Beacol

Supply and fix open well submersible pump set 1 Phase, 230volts, 1HP, 0.75KW capacity with 25mm suction and 25mm dia delivery having discharge capacity 4.3 litre / second at 10metre head with cast iron / MS base plate etc complete all as specified and as directed by Engineer-in-charge. Make: Kirloskar model KOSi-135 or equivalent to KSB /Jyoti / Beacol

Supply and fix swing type Foot Valve 100mm dia conforming to IS 4038 and PN 2.0 shall be swing type rigid sturdy design with minimum loss of head across the valve including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar / Normex / Kartar

Supply and fix swing type Foot Valve 80mm dia conforming to IS 4038 and PN 2.0 shall be swing type rigid sturdy design with minimum loss of head across the valve including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar / Normex / Kartar

Supply and fix swing type Foot Valve 65mm dia conforming to IS 4038 and PN 2.0 shall be swing type rigid sturdy design with minimum loss of head across the valve including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar / Normex / Kartar

Supply and fix swing type Foot Valve 50mm dia conforming to IS 4038 and PN 2.0 shall be swing type rigid sturdy design with minimum loss of head across the valve including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar / Normex / Kartar

Material and labour for cutting the existing road / hard standing etc of any description of surfaces and excavation in trenches not exceeding 30cm wide and depth not less than 45cm for passing of GI pipe and making good the disturbed surface filled with excavated material and top 200mm depth with PCC 1:3:6, type C1 using 20mm graded stone etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for repairing by welding of GI/CI pipe line of any size up to 150mm dia at various locations to prevent leakage of water by welding of flanged / sockets / collars, ferrule or at the joints of including GP Joint, T joint, sluice valves / air release valve / non return valves or damaged pipeline etc., including necessary excavation and returning and filling and making disturbed surface good complete all as specified and as directed by Engineer-in-Charge

Material and labour for for repairing existing water level indicator of Overhead tank / Underground sump, painting, marking levels, replacing the nylon rope, float valve with new nylon rope etc, refixing the same and complete all as per site requirement and as directed by Engineer-in-Charge

Material and labour for chart/ poster/ diagram/ name plate etc made out of prepex sheet 3mm thick, cut to size 1.0 x 1.0 mt,r colour background and diagram and letters including fixing arrangements with screws/ adhesive as required complete all as specified and directed by Engineer-in-Charge. NOTE:- The board should duly written for type of pump, make, capacity, discharge, year of installation & MES no.etc as directed

Supply & Fix in repairs pressure gauge dial type for measurement of the water pressure up to 5 Kg / cm2 rating or as per existing size complete all as specified and directed. Make- Waarrie/H-Guru

Cutting under ground bushes, grass, small plant all as and where directed by EIC and removing the same from site and depositing at a distance n. exc 50 mtr complete all as directed. Note- Unit each is for per installation

Cleaning of valve pit chamber of any size by taking out mud & muddy water and depositing the same at a distance n. exc 20 mtr away from pit including swipping free from all type of dirt including rectification the leakage of valve of any size by using of appropriate size and required packing materials for purpose complete all as specified and as directed by Engineer-in-Charge.

Material and labour for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to plate with GI earth strip 25 x 3mm, 7.5 m long from earth point to test point and other end connected to control board / panel / equipment, laid under floors/plinths or fixed on walls or concealed in wall etc by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel with provision of charcoal & common salt packed upto minimum 150 mm all around the earth plate and protected by 32 mm bore light grade galvanised iron pipe complete all as shown in electrical plate No.3 of MES schedule Part I, 2009 with PCC pit in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, MS angle iron frame of size 50mm x 50mm x 5mm, cast iron cover with locking arrangements, GI 20 mm bore medium grade pipe and CI funnel with wire mesh for watering arrangement including necessary excavation and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge.

Material & labour for fabrication of steel ladder with 50mm dia GI tubing 5mtr long with 25mm dia GI tubing for cross steps, 30cm apart duly welded and with two coat of bitumen black paint and necessary fixing arrangements with MS clamps, nut and bilts duly grouted on wall/ floors complete all as specified and as directed by Engineer-in-Charge.

Supply, install, testing & commissioning wall/Floor mounted cubical type double door LT feeder piller box factory made modular construction fabricated out of 2 mm thick CRCA sheet, epoxy powder coated to give a superior finish , indoor type , totally enclosed dust & vermin proof with locking arrangements (compartment wise) front side opening system Overall size of each incoming & outgoing modules of suitable size and busbar chamber should be suitable for accomodating all Aluminium bus bar strips (40mm x 10mm x 04 Nos) duly covered by PVC sleeves fixed on porcelain insulators, and one independent metering module suitable for accomodating indicator lamps, cable entry/exits cut outs at bottom part as mentioned below, complete electrically inter connected suitable size for all incoming and outgoing MCBs and accessories with fixing arrangement on wall with bolts, nuts & washers, Danger notice board with scull suitable for 415 volts or required size to be fixed on Pannel and consisting of the following accessories including dismantling of old panel all as directed. (a) Panel shall be Manufactured from CPRI approved manufacturer and Drawing for Feeder pillar box shall be first approval by Engr-in-Charge (b) Cost of dismantling of old panel/ feedar pillar box is deemed to be included above. (c) Panel indicating lamp neon/LED type (Red ,Yellow & Blue) with lamp holders - 03 Nos (d) Panel instrumental wiring with FRLS suitable size but not less than 2.5 sqmm copper wire single core - 01 Job (e) All incomming/ outgoing feeders to be marked with suitable size of stencils as directed.

Incoming- (a) MCCB 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, 100 Amps , with thermal adjustable and fixed magnetic setting with extended terminals - 01 No Outgoing :- (a) MCB TPN, 415 Volts,10 KA, 32 Amps -02 Nos. (b) Star delta starter 10 HP 3 Phase motor for open execuision in panel with push button switch ON/OFF indicator on door of each module with over load relay range 22A-32 A, suitable size of contactor and single phase protection relay- 2 Nos.Make-Havells/ Siemens/ Larsen &Tubro/ ABB/ Crompton Greaves/ GE (c) MDXL capacitor heavy duty 10 KVAR 3 phase 440 Volts Box type(Make L&T Cat Part-LTBCH) with capacitor duty contactor (Make L&T Cat Part-MO C15)and 32 Amps TP MCB- 02 Set Make- L & T (d) Inteligent automatic factor controller realy 6 pole voltage 220-440. Make : Runcon, Type- APFC Relay- )1 Nos (h) Digital Type Amphere meter 3 phase CT opearted with suitable size CTs-3 Nos for each meter complete all as directed- 04 Nos (make: L&T, cat Part-WL131010OOOO) (i) Multifunctional meter (VAF + PF meter) for main incomming- 01 Nos.( Make- L&T Cat Part- WL41010OOOO) Make of MCCB & MCB: Larsen &Toubro/ ABB/ Siemens/ Schneider/ Havells/ Legrand/ Indo ASIAN/ C & S Electric/ Bhartia Cuttler Hammer (BCH)

S&F Chlorine dozing pump system to inject solution upto 25 LPH comprising dozing pump coupled with three phase electric motor of capacity 0.5 HP, 1440 RPM assembly with agitator in one motor with SS sweep blade, duly FRP coated FRP tank 150 ltrs capacity complete unit mounted on heavy duty MS fabricated frame duly anticorrosive paint complete all as specified and as directed by Engr-in-charge.

S&F Air release Valve 150mm size CI body complete all as specified and as directed by Engr-in-charge.

Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam, tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets/TATA

Material and labour for complete removal of existing treatment of plastered wall surface and applying two coats of Acrylic weather proof coat 100% exterior grade paint over one coat of acrylic primer over thick layer of external grade putty complete all as specified and as directed by Engineer-in-Charge. Make : APEX ULTIMA” of Asian Paints/ “WEATHER COAT ALL GUARD” of Berger Paints/"EXCEL TOP GUARD” of Nerolac/ “DULUX WEATHERSHIELD MAX” of ICI India

Supply and fix star delta starter suitable for submersible pumpset 10 HP pump motor in Sheet-Steel Enclosure Type MN with Single Phase Protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) complete all as specified and as directed by Engineer-in-charge. Make- M/s L & T or equivalent of M/s Siemens/ C & S/ ABB

Supply and fix gallon seal for pump motor, sluice valve of any sizes complete all as specified and as directed by Engineer-in-charge.

Supply and fix pressure booster pump 0.5HP with CRI pump controller complete all as specified and as directed by Engineer-in-charge.

S & F in repairs of valve chamber/ UG sump covers with angle iron framed works by welding angle iron of size 40x40x6mm and 3mm MS sheets of Fe 410W Gde E- 250quality B with handle and hinged at one side and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Dismantling and taking down cenrtrifugal pump set 15 to 40HP capacity 3 phase, 440volts from foundation disconnecting all electrical connection induction motor, transportation from installation to workshop, renewal of U/S spare parts, re-assembling pumping set including testing and commissioning including proper alignment of pump with motor complete as specified and as directed by Engr.-in-charge.)

Supply only following spare parts (Item No 62 to 66) suitable for existing 15 to 40 HP centrifugal pump set as required -

Ball bearing Suitable for centrifugal pump set 15 to 25 HP

Ball bearing Suitable for centrifugal pump set 30 to 40 HP

CI impeller suitable for centrifugal pump set 15 to 40 HP

Fan blade set

Low jaw coupling including necessary key for fixing on shafts as required

Rubber star packing of size 01/10/13/0/15 for jaw coupling fitting

Supply only SKF wheel bearing Grease of 1 kg box (base oil viscosity 110 mm2/s @ 40 degree C) operating temperature -(-3) to + 120 degree C)

Supply only lead wool (caulking lead) confirming to IS-782-1978

Supply only Chlorscope (Chlorine Testing Kit) 1 PPM to 5 PPM for testing of chlorine in water including orthodoline solution complete all as specified.

Supply and fix single pointed air termination aluminium rod, 12mm dia, 300mm long including taking down old unserviceable aluminium rod, all as specified and directed by Engr-in-Charge.

Supply and fix aluminium strip of 25 x 3.15mm , including taking down of old unsercivable aluminium strip, complete all as specified and directed by Engr-in-Charge. Note : Rate for Necessary insulator for fixing of strip is deemed to be included in the quoted rate.

Material and labour for Plain Cement Concrete 1:3:6 type C2 using 40mm graded stone aggregate as in coping of pole including necessary formwork for fair finished surfaces etc complete all as specified and as directed by the Engineer-in-charge

Material and labour for test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm, drilled and screwed including 3 nos 8mm dia 25mm long hexagonal screws, including taking down old unserviceable complete all as specified and as directed by Engineer-in-Charge.

Supplying, laying,connecting, testing & commissioning LT UG XLPE insulated, heavy duty, 1100 V grade (earthed) electric cable with aluminium conductor, served with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed of size 16 Sqmm x 4 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by Engineer-in-Charge Note : Earthwork excavation, DWC/GI pipe for cable protection shall be measured and paid separately in their respective items Make: Cable Corporation of India (CCI)/ Asian Cable Co, Chattisgarh/ Finolex/ Polycab/ Gloster/Universal/ RPG Cables Ltd , Thane/ Havells India Ltd/ RR Kabel/ KEI Industries Ltd(KEI)

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.5 m in depth, for laying of cable etc, not exceeding 10 sqm on plan and getting out in soft/loose soil for laying of underground cable complete all as specified and as directed by Engineer-in-Charge.

Supply and lay double wall corrugated (DWC) HDPE pipe 40/32mm bore , as per IS-16205 including couplers and bend for cable protection laid in trenches etc complete all as specified and as directed by Engineer-in-Charge Make : TELEREX 450N/ Rex Polyextrusion Ltd/ Finolex/ Prince Pipes and fittings ltd/Kisan/Supreme/JAIN IRRIGATION SYS/ Astral

Material and labour for earthing complete with Galvanised steel earth plate electrode 60cm X 60cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to plate with 32 x 6mm GI earth strip, 7.5m long from earth point to test point and other end connected to control board / panel / equipment, laid under floors/plinths or fixed on walls or concealed in wall etc by means of bolts, nuts, check nuts and washers made out of galvanized iron or steel with provision of charcoal & common salt not less than 50Kg, Benzonite powder 20 KG in each earthing packed upto maximum 30 cm on both side of plate for reducing the earth resistance complete and GI strip protected by 40mm bore light grade galvanized iron pipe for protection to earth lead ,watering pipe of size 20mm dia with funnel and mesh, PCC pit with CI cover frame complete all as shown in electrical plate No. 3 of MES schedule Part I, 2009 w complete all as specified and as directed by Engineer-in-Charge. Note :- (i) Contractor should submit test report of earthing after installation to Engineer -in-Charge

Supply and fix in repairs galvanised iron pipe, light grade, 40mm bore for cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle, wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: Tata/ Jindal/ BST/ Surya/ KS Engineering/ Zenith/ Swastik/ Prakash

Fixing only in repairs the disturbed existing aluminium strip of size 25 x 3.15mm with saddles and fixing screws and other accessories etc for roof conductors above ground at any location to its original places complete all as specified and as directed by Engineer-in-Charge.

Fixing only in repairs the disturbed existing Gl strip of size 32 x 6mm with necessary fixing screws and other acessories etc above ground level at any location to its original places complete all as specified and directed by Engr-in-Charge.

Material and labour for Pre-cast cement concrete block masonry 1:2:4 type B1, (using 20mm graded stone aqggregate), with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Gl sheet of size 10 x 8 inch welded with 2.5 foot of angle iron for marking earth pit grouted on ground with PCC at different area complete all as specified and as directed by Engineer-in-Charge.

supply and fix plastic coating print in Gl sheet of size 10 x 8 inch for marking earth pit grouted on ground at different area complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Hose pipe of size 63 mm bore 15 m long with both end 63 mm dia connector with Gun metal fire hydrant nozzle of size one end 63 mm and other end 15 mm bore all as per specified and as directed by Engineer-in-Charge.

Supply and fix fire hydrant GM landing valve type 'A' (Single head out let) of size 63 mm dia, confirming to IS-5290 complete all as specified and as directed by Engineer-in-Charge.

Supply and fix hose box made of 18 gauge MS sheet 800mm x 600mm x 250mm width with double door with 4 mm thick glass and door frame made of 16 gauge MS sheet painted fire red outside and brilliant white inside yard complete all as specified and as directed by Engr-in-charge.

Supply and fix fully automatic star delta starter suitable for 15 HP motor in sheet steel enclosure with citation fully automatic star delta starter with NHD contactor & pnuematic timers for 15HP 3 phase overload relay range 13-20Amps contractor type N01N contactor rating 16Amps complete all as specified and as directed by Engineer-in-charge. Make:BCH Cat Part No. NASAKLEN/LOR or equivalent in Havells / Legrand / L&T / Siemens / C & S / ABB

M&L for Servicing of existing installed Solar water heaters any type at any place in cantonment upto 1000 litre capacity and repairing the same including all Plumbing work, Chemical Descaling of collector plate/pipe, replacement of unserviceable parts and checking for hot water supply complete.(Note - U/s parts shall be measured separately under relevant item of schedule as supply only).

Supply only Back sheet of collector plate suitable for already existing collector plate complete all as directed by Engr-in-charge.

M&L for replacement of broken glass of collector plate/ pipe of suitable size and thickness all as directed on site complete.

M&L for brazing of solar panel complete all as specified and as directed complete.

M&L for glass wool insulation of suitable thickness for GI pipe of hot water supply complete.

Supply & Fix in repairs rotational moulded polyethylene water storage tank (Cylinderical vertical including CI tank with locking arrangements as per BMC specifications) triple layered with ISI marked of 1000 ltrs capacity with inlet & outlet connections, tank nipples, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engr-in-Charge. Make : Sintex/ Polycon/ Rotex

Supplying and laying CPVC pipes, heavy duty, SDR 11 of outer diameter 25mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with suitable fixing clamps/ fastners including taking down existing pipes complete all as specified and as directed by Engineer-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supplying and laying CPVC pipes, heavy duty, SDR 11 of outer diameter 32mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with suitable fixing clamps/ fastners including taking down existing pipes complete all as specified and as directed by Engineer-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supplying and laying CPVC pipes, heavy duty, SDR 11 of outer diameter 40mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with suitable fixing clamps/ fastners including taking down existing pipes complete all as specified and as directed by Engineer-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supply & Fix in repairs Evacuated tube collector (ETC tubes) not less than 58mm dia & 200mm length as per existing including taking down old unserviceable tubes complete all as specified and as directed by Engineer-in-Charge.

Supply & Fix in repairs CPVC ball valves, heavy duty, SDR 11 of outer diameter 25mm, fixed with suitable solvent complete all as specified and directed by Engr-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supply & Fix in repairs CPVC ball valves, heavy duty, SDR 11 of outer diameter 32mm, fixed with suitable solvent complete all as specified and directed by Engr-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supply & Fix in repairs CPVC ball valves, heavy duty, SDR 11 of outer diameter 40mm, fixed with suitable solvent complete all as specified and directed by Engr-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Material & Labour for painting the old water tank, staging, ladders, railings, framework etc including scrapping and removing the old painted surfaces and painting /matching the same colour paint with two coats of synthetic enamel paint overa coat of primer all as specified and directed by Engineer-in-Charge. Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Supply and fix maintenance free lead acid battery, 12 volt ,80 AH all as specified and as directed. Make: Exide or Amaron.

M&L for Repairing of Steel gate including making necessary hinges for both top and bottom of required size, welding the same in existing steel gate including necessary nuts and bolts and painting one coat of synthetic enamel paint over one coat of red oxide complete all as specified and as directed by Engr-in-charge.

M&L for servicing of Diesel Engine Pump 10 HP including replacement of all unserviceable parts, complete oiling and greasing of all parts complete all as directed by Engr-in-charge.

Supply and fix anodised aluminium snap grid frame work for false ceiling conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, 4 mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm, cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system including exposed metal frame ceiling with 8mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fiber for fixing in 600 x 600 mm grid system with all connected accessories suitably placed in false ceiling grid as per manufacture instruction complete with necessary design in single/double complete all as specified and as directed by Engineer-in-Charge. Make: Gypsum board /Arm Strong/Ramco/Bisan

Demolition of stone masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge.

M&L for surface excavation n exc 15 cm deep and averaging 10 cm deep and cleaning of surrounding of sewage / drainage installation by cutting vegitation, bushes, grass etc and suface dressing complete all as specified and directed.

Desludging underground sewage sump of 20000 gallon capacity and removing away sludge of cantonment area and disposing the same as per proper procedure including cleaning of sump inside and surrounding at a distance of 5 mtr radius all around by removing of all vegitation, bushes, mud, dirt, dust etc and shift to a distance not exceeding 50 meter including cleaning of pump house complete all as specified and directed by Engineer-in-charge. Note:- 1. Quoted rates shall also include for excavation of pits for burying sludge and removing of surplus spoil to a distance not exceeding 50 meter. 2. T&P, Plant, man power, labour & transportation charges etc is deemed to be included in quoted rates.

Labour and tools for lifting of submersible sewage pump from existing sewage sump well, cleaning of sludge / floating particles, washing and re lowering the pump including disconnection, connections, testing, commissioning complete.

Supply and fix in repairs Solar Hot water tank with inner tank SS 304 L materials made up of high grade stainless steel with insulation materials used of high quality PUF with capacity of 500 Ltr and powder coated of outer tank PC on MS, with three layer vaccum tube certified ISO 9001:2008 extra auxiliary tank fitted insted of air vent, ISI marked with thermostat, with additional safety features like pressure release valve to manage excess pressure including connecting with existing ETC tubes/Plates and taking down existing tank complete all as specified and directed by engr-in-charge. Make : Supereme Solar/ Jain Solar/ Tata BP

Supply and fix in repairs Solar Hot water tank with inner tank SS 304 L materials made up of high grade stainless steel with insulation materials used of high quality PUF with capacity of 250 Ltr and powder coated of outer tank PC on MS, with three layer vaccum tube certified ISO 9001:2008 extra auxiliary tank fitted insted of air vent, ISI marked with thermostat, with additional safety features like pressure release valve to manage excess pressure including connecting with existing ETC tubes/Plates and taking down existing tank complete all as specified and directed by engr-in-charge. Make : Supereme Solar/ Jain Solar/ Tata BP

Material & labour for Fire point / fire stand shed cover of size 1.2m x 0.5m of height 1.2m with GI sheet of thickness 0.5mm made out of angle iron of size 40mm x 40mm x 6 mm grouted with PCC 1:3:6 with all fittings and fixtures including two coats of synthetic enamel paint of red colour over a coat of red oxide primer and writing letters of standard size in white paint over the shed and bucket etc complete including supply & fixing of following for each fire point as per IS:7673-2004:- (a) 24 gauge GI Sheet bucket (09 ltrs capacity) - 03 Nos (b) Shovels with handle - 02 Nos (c) Fire hooks with bamboo of length not less then 10ft - 02 Nos (d) Fire beater with bamboo of length not less then 10ft - 02 Nos

Taking up old unserviceable Ductile Iron water mains 100/150 mm dia including all fittings, with spigot and socket ends and lead joints including burning out joints and lead complete all as specified and as directed by Engineer-in-Charge.

Supplying, laying and jointing in repairs centrifugally (Spun) ductile iron pipe (Class K-7) 150 mm bore with suitable for push on joints and centrifugally applied cement mortar leveling inside and Zinc coating with bituminous finish coat on outside of the pipe conforming to 1S-8329 of 2000, in any length, laid in trenches in proper alignment including necessary cut to length to match existing fitting/pipes or insertion of new CI specials etc complete all as specified and as directed by Engineer-in-Charge Note: Rubber gasket joints (tyton), specials such as bends/ tappers/ tee/ cross of any type and size and earth work excavation will be measured and paid separately. Make: Tisco / Electro Steel / Kesoram / Lanco / Jindal / Kalinga / Kapilansh.

Supply and fix Ductile Iron fittings such as spigot socketed pipe bends (any type, radius and angle), tappers of any type (Straight, bend, increasing, decreasing or double socket etc), Tee pieces, single branch, double branch, cross (all sockets or socket and spigot) collars, caps and plugs up to 150 mm dia including taking down existing etc complete all as specified and as directed by Engineer-in-Charge. Make: Tisco / Electro Steel / Kesoram / Lanco / Jindal / Kalinga / Kapilansh

Supplying, installing, testing and commissioning of suitable size factory made out door type, dust and vermin proof, LT feeder pillar box double door, cubical and compartmentalized type with minimum depth size 450mm, 415 volts, AC, 50 Hz, fabricated with 3.15mm thick CRCA sheet for outer side and 2mm thick inside complete with and including mounted on angle iron frame stand of size 50 x 50 x 6 mm thick 50 cm long leg, grouted in PCC (1:2:4) type B1 (using 20 mm graded stone aggregate), spray painted inside and outside, powder coated of approved colour by Engineer-in-Charge, enclosed bus bar chamber with aluminium bus bar (04 Nos of rating capacity 400 Amps), mounted on PVC insulators, electric connection complete with from MCCB to main bus bar, cable glands, thimble complete with and including openable shutters butt hinged, locking arrangement including PCC work, excavation & earth work, taking down old rusted feeder pillar box complete and comprising supply and fix for following etc complete all as specified and as directed by Engineer-in-Charge:-

INCOMING: (a) MCCB 4 pole, 250 Amps, 415 volts, 50 Hz, 36 KA, adjustable thermal & adjustable magnetic settings - 01 No. BUSBAR : (a) Bus bar chamber with 400 Amps aluminium strip with heat shrinkable insulating sleeve size 50 x 10mm - 4Nos of required length supported on FRP insulators, internal wiring for indicators with 2.5 Sqmm copper cable single core. (b) CT coil of ratio 200/5 Amps - 03 Nos (c) Digital type Multifunction meter of class I - 1 Nos Make : L & T Model : 4400 LED series or equivalent in Siemens/ Scneider d) LED type indicator lamps RYB - 01 Set OUTGOING: (a) MCCB 4 pole, 100 Amps, 415 volts, 50 Hz, 16 KA, adjustable thermal & adjustable magnetic settings - 06 Nos (b) MCB 4 pole 32 Amp, 415 volt, 16KA, 50 Hz, adjustable thermal and adjustable magnetic settings - 01 Nos. (spare). Note: (i) Contactor shall be submit the drawings of panels for approval before fabrication in factory. (ii) LT panel board shall be CPRI approved. WL41010OOOO) Make of MCCB & MCB: Larsen &Toubro/ ABB/ Siemens/ Schneider/ Havells/ Legrand/ Indo ASIAN/ C & S Electric/ Bhartia Cuttler Hammer (BCH)

Dismantling and taking down cenrtrifugal pump set upto 10 HP capacity 3 phase, 440volts from foundation disconnecting all electrical connection induction motor, transportation from installation to workshop, renewal of U/S spare parts, re-assembling pumping set including testing and commissioning including proper alignment of pump with motor complete as specified and as directed by Engr.-in-charge.)

Supply only following spare parts (Item No 120 to 123) suitable for existing 15 to 40 HP centrifugal pump set as required -

Ball bearing Suitable for centrifugal pump set upto 10 HP

CI impeller suitable for centrifugal pump set upto 10 HP

Fan blade set

Low jaw coupling including necessary key for fixing on shafts as required

Note: Deduct Credit for demolished / dismantled material of Rs. (-) 89,895.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

Chaudhary Enterprises (BID ID -3491478)