REPAIR MAINT OF SUBMERSIBLE PUMP SETS PANEL BOARD AND OTHER CONNECTED WORKS OF PUMP HOUSES IN DOMESTIC AREA OF AF STN CHAKERI, KANPUR

Amount

Taking / lifting out defective submersible pumps set from bore well complete with column pipe steel rope, submersible cable and accessories etc and relowering and commissioning the same after repairing works and testing complete all as specified and directed for the following capacity:- 45/40 HP 3 Phase Note for item No. 1 to 04 : Replacement of wornout parts / spares with new components spares shall be measured and paid separately under relevant item of schedule'A' as supply only and fixing of the same is deemed to be included under this item.

All as per item No 1 above but for 35/30HP 3 phase

All as per item No 1 above but for 20/25 HP 3 Phase

All as per item No 1 above but for 2/1.5 HP single Phase

Dismantling , taking out complete burnt winding wire of submersible motor, and winding with PVC insulated copper wire of existing gauge as per motor capacity using new insulation material such as insulating paper sleeves etc. Including cleaning of stator slots replacement of defective parts and testing complete, replacement of submersible cable as required length complete all as specified and directed for the following capacities :- 45/40 HP 3 Phase Note for item No 05 to 08 : 1. Replacement of defective parts with new parts shall be measured and paid separately under relevant item of schedule 'A' as supply only and fixing of the same is deemed to be included under this item.

All as per item No. 05 above but for 35/30HP 3 phase

All as per item No. 05 above but for 20/25 HP 3 Phase

All as per item No. 05 above but for 2/1.5 HP single Phase

S&F in repairs motor bush of gun metal upper and lower for 45/40 HPcapacity (Set of two) complete all as specified and directed.

All as per item No 9 above but for 35/30 HP (Set of two) complete all as specified and directed.

All as per item No 9 above but for 25/20 HP (Set of two) complete all as specified and directed.

All as per item No 9 above but for 2/1.5 HP (Set of two) complete all as specified and directed.

S&F in repairs rotor bearings sleeve upper and lower for 45/40 capacity, (set of two.) complete all as specified and directed.

All as per item No 13 above but for 35/30 HP (Set of two)

All as per item No 13 above but for 25/20 HP (Set of two)

All as per item No 13 above but for 2/1.5 HP (Set of two)

S&F in repairs coupling arrangement with key for motor pump for 45/40 HP Capacity complete all as specified and directed.

All as per item No 17 above but for 35/30 HP

All as per item No 17 above but for 25/20 HP

All as per item No 17 above but for 2/1.5 HP

S&F in repairs sand guard for submersible pump set for 45/40/35/30/25/20 HP capacity complete all as specified and directed.

S&F in repairs sand guard for submersible pump set for 2/1.5 HP capacity complete all as specified and directed.

S&F in repairs thrust bearing assembly for submersible pump set motor for the capacity 45/40/35/30 HP complete all as specified and directed.

S&F in repairs thrust bearing assembly for submersible pump set motor for the capacity 25/20 HP complete all as specified and directed.

S&F in repairs thrust bearing assembly for submersible pump set motor for the capacity 2/1.5 HP complete all as specified and directed.

S&F in repairs epoxy type cable jointing kit complete with all the jointing material, ferrule, for 1100 volts flat submersible copper conductor cable 16/10 Sqmm 3 cores complete all as specified and directed. Make : Reychem/Birla 3 M or any make approved by GE

All as per item No 26 above but for 4/2.5 Sqmm 2 Cores

S&F rubber gasket (packing) suitable for 80 to 150mm dia flange complete all as specified and directed.

S&F in repairs MS Nut bolts with spring washers off sizes complete all as specified and directed.

S&F in repairs steel wire rope 12 mm dia for hanging of submersible pump set complete all as specified and directed..

S&F in repairs electric cable for submersible pump set, flat 16 Sqmm 3 core stranded copper conductor PVC sheathed cable complete all as specified and directed.. Make- Finolex/ Paragon/Havells

All as per item No 31 above but for 25 sq mm 3 core

All as per item No 31 above but for 10 sq mm 3 core

Dismantling submersible pump, straightening & polishing of pump shaft, making screw and key way, turning surfacing polishing to impellers, CI bowl complete including replacement of worn out parts as per requirement complete all as specified and directed. 45/40 HP 3 Phase Note : Replacement of wornout parts / spares with new components spares shall be measured and paid separately under relevant item of schedule'A' as supply only and fixing of the same is deemed to be included under this item.

All as per item No 34 above but for 35/30HP 3 phase

All as per item No 34 above but for 20/25 HP 3 Phase

All as per item No 34 above but for 2/1.5 HP single Phase

S&F in repairs impeller with key and distance bushes for 45/40/30/20 HP capacity pump complete all as specified and directed.

S&F PVC impeller for 1.5/2HP capacity pump complete all as specified and directed.

S&F in repairs pump shaft of stainless steel suitable for 45/40/30/20 HP capacity pump complete all as specified and directed.

S&F in repairs NRV for 45/40/30/20 HP capacity pump complete all as specified and directed.

S&F in repairs bearing bush for submersible pump for 45/40/30/20 HP capacity complete all as specified and directed..

S&F in repairs bowl assembly for submersible pump set for the capacity 45/40/30/20 HP complete all as specified and directed.

S&F in repairs distance sleeves for submersible pump for 40/30/20 HP capacity complete all as specified and directed.

Repair/maint of LT panel /Starter of any size/type, checking and tightening of all incoming and outgoing connections by replacing alluminium lugs, pieces of burnt wires as required to make the starter /panel functional complete all as specified and directed. .

S&F in repairs bus bar of 100 A and 415 V 4 Nos and joining all incoming and outgoing connectiom by suitable Lugs complete all as specified and directed.

S&F in repairs MCCB TP, 415V, 100 Amps with breaking capacity 10 KA complete all as specified and directed.. Make- L&T/Legrand/Siemens

S&F in repairs MCCB TP, 415V, 200 Amps with breaking capacity 25 KA complete all as specified and directed. Make- L&T/Legrand/Siemens

S&F in repairs over load relay for starter suitable for 45/40 HP submersible pump set complete all as specified and directed. Make- L&T/Legrand/Siemens

S&F in repairs MCB 40 Amps, TPN, 415 volts,'C' Curve AC 10 KA complete all as specified and directed. Make- L&T/Legrand/Siemens

S&F in repairs power contactor TP as per existing type & make fitted at site for starter suitable for 40 HP/30HP/20 HP submersible pump set complete all as specified and directed. Make- L&T/Legrand/Siemens

S&F in repairs over load relay for starter suitable for 40 HP/30HP/20HP submersible pump set complete all as specified and directed. Make- L&T/Legrand/Siemens

S&F in repairs timer suitable for star delta starter for 40/30/25/20 HP submersible pump set complete all as specified and directed. Make- L&T/Legrand/Siemens

S&F in repairs fully automatic star delta starter for submerssible pump set including connecting all incoming and outgoing copper wire complete all as specified and directed. Make- L&T cat part No-MU-G 50.

S&F in repairs fully automatic star delta starter for submerssible pump set including connecting all incoming and outgoing copper wire complete all as specified and directed. . Make- L&T cat part No-MU-G 30.

S&F in repairs of Single phase preventer complete all as specified and directed. Make- L&T/Legrand/Minilek

S&F in repairs fully automatic star delta starter for submerssible pump set including connecting all incoming and outgoing copper wire complete all as specified and directed. Make- L&T cat part No-MU-G 10.

S&F in repairs change over switch on load type in open execution front handle operated 415V with rating of 200 Amps fore pole 415 volt complete all as specified and directed. Make:-Havells /Legrand/L&T

S&F in repairs street light fitting 45 watt LED with pressure die cast housing suitable for scondary road/bldgs power consumtion should not be more than 45 watt and power factor should not be less than 0.90 with suitable GI pipe medium grade bracket incl clamps, nuts , bolts and washers etc with all fixing arrangement complete all as per specified and directed. Make:- wipro/Crompton Greaves/Havells

Testing of drinking water (chemical analysis) as per IS : 10500 from authorised / approved lab after taking the sample from Pump houses in steralised container as per guideline of medical authority and submitting test report to Engr-in-Charge complete all as specified & directed . Lab for testing - Bharat test House/CIMEC/Spectro as approved by GE.

M&L for earthing complete with galvenised steel earth plate electrode 600 x 600 x6 mm thick buried directly in ground (earth pit not less than 2.5 m deep below GL) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 32x6 mm as earthing lead by means of boths, nuts check nuts and washers of GI all as shown in electrical plate No-5 of SSR Pt-I work including for necessary excavation earth work, PCC pit and RCC cover, funnel with salt ,charcoal dust, water pipe line 20 mm & protection pipe 40 mm, wire mesh complete all as specified and directed.

S&F GI strip 32x6mm on wall/batten or recessed or buried in ground complete all as specified and directed.

S&F in repairs aviation Light with all necessary connection complete all as specified and directed. Make-Bajaj/Crompton/Philips

S&F in repairs 2.5 sqmm 2 Core copper flexible cable with suitable clamps complete all as specified and directed. Make-havells/Finolex/Polycab

Supply only MS column pipe of size 100 mm in standard length of 3.0 mtr, heavy duty duly threaded at ends with provision of MS flange duly drilled and welded, complete all as specified and directed. Make : Jindal/TATA.

Supply only MS column pipe of size 150 mm in standard length of 3.0 mtr, heavy duty duly threaded at ends with provision of MS flange duly drilled and welded, complete all as specified and directed. Make : Jindal/TATA.

Supply and fixing in replacement phase sequencer cum pump protection system 415/440 volts, 50 Hz, internal working voltage 12/14 volt, suitable for 50 HP with MNX 100 comtactor capacity load for auto change of phase sequence if incommimg phase sequence changes, single phasing prevention system and adjustable low and high voltage protection system to protect the machinery, mounting on bracket made out 40x3 mm angle iron frame, all control wirings, cable connections complete all as specified and directed. Make : Indian Engineering Co/United Engineering

S&F in repairs electronic microprocessor based digital & wire less type water level indicator with alarm at time of full level/Low level in tank including all eqpts accomodated in GI sheet box or completely enclosed complete including testing & Commissioning complete all as specified and directed.. Make- Benzer/SAPCON/Aquabrim

Supply only chlorine testing kit comprising of samples of chlorine contents in seald tube from 0.1 to 2.0 PPM and othotodoline solution , testing tube complete all as specified and as directed.

S&F in repairs pressure gauge size 100 mm dia round,range 0-10 Kg/cm2 complete with connecting pipe & air cock for 15 mm dia GI pipe complete all as specified and directed. Make- H guru/Japson

S&F in repairs 1100 volts grade cable PVC insulated 6 sqmm multistranded aluminium conductor, overall PVC sheathed twin core flat complete all as specified and directed.

M&L for design, manufacture, supply, install and commission in replacement LED display boards of following sizes having compact design, and maintenance friendly. The base of the board made of ACP (Aluminium composite Panel) 3mm thick and back side of board covered with GI sheet 24 SWG, the letters and borders made of acrylic sheet 3mm thick of colour as approved by GE/Engr-in-charge. LED module should as per requirement of letter space,the display language may be English/ Hindi (Alpha Numeric), its visibility should be suitable for Day & Night (Out door application) and should be visible upto 25Mtr. (Minimum), the text effect should be static, the LED suitable for power supply 230 Volts/ 50Hz, AC, with switch ON and OFF the power supply to the display board. The board shall be suitably braced on back side with angle iron 40 mm x 40 mm x 3 mm and making good of disturbed surfaces as per original complete all as specified and directed by GE. (a) Rectangular board having max 40 letters or characters in English language letter or character size, height not exceeding 255 mm and back depth Max 45 mm of suitable width & one logo of dia not exceeding 450 mm and back depth 80 mm as per sample complete all as specified and directed.

Preetpowercontrol