Constuction of Block Development Office building at Una, Distt. Una H.P.

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three meters) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimeter)layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Excavation in earth work in all kinds of classification of soil and filling in 15 cm (fifteen centimetre) layer in foundation and plinths etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per directed by the Engineer- in- Charge including carriage of materials in all leads and lifts, disposed material to be neatly dressed ,levelled. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:6:12 (One cement; Six sand; Twelve graded broken/crushed stone aggregate 40mm (Forty milimetres) nominal size mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight graded broken/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth and depressed portion of slab within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:3:6 (One cement : three sand : six graded broken/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth and depressed portion of slab within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation footings, bases of columns and mass concrete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like including mouldings where ever required as per architectural drawing and the like floor etc. within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etc; whereever required within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surfaces such as walls (any thickness) partitions and the likeincluding attached pillasters buttresses, plinth and string courses and the like Within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in work in edge of slab and breaks in floors and walls of any thickness within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 330 kg (Three hundred thirty kilogram) per cubic meter to give an smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 310 kg (Three hundred ten kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in Suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers including mouldings, cornices etc; where ever requireed within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 310 kg (Three hundred ten kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in Columns, pillars posts and struts for all floors heights within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 310 kg (Three hundred ten kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in wall (any thicness but not less than 0.1 metre thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto floor two level within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 310 kg (Three hundred ten kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in Stair cases (except spiral stair cases excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor level within all leads, lifts of materials and other Incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of 320 kg (Three hundred twenty kilogram) per cubic meter to give an smooth surfaces mechanically mixed and vibrated including curing complete, including cost of form work for plain concrete work in string courses coping bed plates, ancher blocks plain window sills and like concrete within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing Tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete including cost of binding wires complete and other incidentals due for its completion for all floors within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Precast Cement Concrete block masonary (including quion blocks,jamb blocks,closer etc.)with solid concrete blocks of approved size made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm and down gauge) foundation and plinth upto floor level two in:- Cement mortar 1:6 (Size 200mm thick) within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Precast concrete block masonary in partiton walls 10 cm. thick with solid blocks of approved size including quion blocks,jamb blocks,closer etc. made of cement concrete 1:3:6 (1 cement :3 sand :6 graded stone aggregate 40 mm and down gauge) in :- Cement mortar 1:6 within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Second Class Bricks work using common burnt clay building bricks in super-structure upto all floor level with Cement Mortar 1:6 (One Cement : Six Sand) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Provoding and fixing powder coated aluminium work for door,window ,ventilators and parttions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required sahde according to IS 1868.(Minimum anodic coating of grade AC 15 ) fixed with rawplugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junction,at top,bottom sides with required PVC/Neoprene felt etc.Aluminium sections shall be smooth,rustfree,straight,mitred and jointed mechanically where ever required including cleat angle,aluminium,snap beading for glazing /panelling C.P brass/Stainless steel screws .All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

For doors windows and ventilators and galzed partitions frames.

Provoding and fixing powder coated aluminium work for door,window ,ventilators and parttions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required sahde according to IS 1868.(Minimum anodic coating of grade AC 15 ) fixed with rawplugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junction,at top,bottom sides with required PVC/Neoprene felt etc.Aluminium sections shall be smooth,rustfree,straight,mitred and jointed mechanically where ever required including cleat angle,aluminium,snap beading for glazing /panelling C.P brass/Stainless steel screws .All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

For Shutters of door windows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required including the cost of PVC/Neoprene gaskets as required (fittings and glazing /panelling shall be paid for seprately)

Providing and fixing glazing in aluminium door ,window,ventilator shutters and partitons etc with PVC/neoprenes gasket etc. complete as per architectural drawings and the directions of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic term.)The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Glazing with float glass panes of 6 mm thickness (weight not less than 13.75 kg/sqm.

Providing And Fixing flush Door shutters interior grade commercial type ,core of black board construction with frame of first class hard wood welll matched cxommercial ply veneering with vertical grains of cross bends and face veneers on both face of shutter.35mm thick including M.S Butt hinges. All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 1.00 mm thick coloured or plain laminate sheet (Sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315 ) for aluminium door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of engineer-in-charge I/C making good the floors.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing & fixing anodized matt finished aluminium Pilot/Sheet or equivalent sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. whithin all leads, lifts of materials and other incidentals. As per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

300x16mm (Three hundred fifty into Sixteen milimetres) size

250x16mm (Two hundred fifty into Sixteen milimetres) size

Providing and fixing matt finished anodized aluminium Tower bolts (Barrel type) Pilot/Sheel or its equivalent anodized transparent or dyed to required colour and shade with necessary screws etc. within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

150x10mm (one hundred fifty into Ten milimetres) size

100x10mm (one hundred fifty into Ten milimetres) size

Providing and fixing aluminium handles Pilot/Sheel or its equivalent anodized transparent or dyed to required colour and shade with necessary screws etc. within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

125mm (One hundred twenty five milimetres) size

100mm (One hundred milimetres) size

Steel work welded in built up sections trusses and framed work, including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint in gratings framed gaurds, bars, ladders, railing, brackets and similar work, within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

40mm thick cement concrete flooring with 25mm under layer of cement concrete 1:3:6(1 cement :3 sand :6stone aggregate of size 12.5mm and below) and 15mm weaking layer in cement concrete 1:2 to 3(1 cement :2 to 3 stone aggregate of size 4.75 mm and below) laid integral with base course and finished with a floating coat of neat cement within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying granite stone in flooring 20 mm (average) thickness base of cement mortar 1:3 (1 cement 3 sand )laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete.20 mm thick within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing on wall face 100mm (One hundred milimetres) diametres P.V.C. rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre as per ISI finolex / Relience / vectus pipe confirming to IS code 13592 for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. acessories for rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre as per ISI finolex / relience / vectus or its equivalent for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

100mm (One hundred milimtres) diametrees PVC Plain bend.

Providing and fixing M.S. holder bat clamps of approved design to P.V.C.. rain water pipe embedded in and including cement concrete blocks 10x10x20cm of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etc; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

100mm (One hundred milimetres) diameter.

Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying priming coat on new concrete/masonary/asbestos cement/plastered surfaces after and including preparing the suface by throughly cleaning oil, grease, dirt and other foreign matter and sand papering as required with:-Readymixed primer within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacturte for interior grade on undecorated concrete/stone/plasteres wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for metling the surface.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Finishing wall with weather proof exterior grade emulsion( Apex ultima) approved brand and manufacture And of required shade on undecorated Wall surfaces (two coat) to give an even Shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including carriage of material in all leads and liftsas per direction of Engineer-in charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new concrete/plastered surfaces with enamel paint of approved brand & manufacture to give an even shade i/c cleaning of dirt/dust within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with ready mixed paint, brushing to give an even shade including cleaning of all dirt,dust and other foreign matter,sand papering and stopping including carriage of material in all leads and lifts. : with enamel paint other than white within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new steel and other metal surfaces, with ready mixed paint, brushing to give an even shade including cleaning of all dirt,dust and other foreign matter,sand papering and stopping including carriage of material in all leads and lifts. : with enamel paint other than white within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Provoding and fixing aluminium anodised powder coated pattern to existing window/ ventilatior with 80mmx80mm panels holes with 25x8mmthick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames ( aluminium channels base frames to be measured and paid for separately) All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying Double Charged Vitrified floor tiles in different sizes in light colour shades thickness ranging from 11 to 12mm with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete in all respect as per direction of Engineer in charge. (To be fixed in hairline joint finish).Size of Tile 800x800 mm(Note:-The tiles should be in Matt or Mirror finish as required in design in the required shade in first grade prime quality without any warping undulation, curving or bulging of the top surface. The tiles shall be supplied and installed at site through an expert installer including cost of all spacers and other accessories . All samples for tiles shall be approved and before execution.)All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying Double Charged Vitrified floor tiles in different sizes in light colour shades thickness ranging from 11 to 12mm with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete in all respect as per direction of Engineer in charge. (To be fixed in hairline joint finish).Size of Tile 600x600 mm (Note:-The tiles should be in Matt or Mirror finish as required in design in the required shade in first grade prime quality without any warping undulation, curving or bulging of the top surface. The tiles shall be supplied and installed at site through an expert installer including cost of all spacers and other accessories . All samples for tiles shall be approved and before execution.) All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying Double Charged Vitrified tiles in different sizes in light colour shades ,thickness ranging from 11 to 12mm with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete in all respect as per direction of Engineer in charge. (To be fixed in hairline joint finish). Size of Tile 600x600 mm (Note:-The tiles should be in matt or mirror finish as required in design in the required shade in first grade prime quality without any warping undulation, curving or bulging of the top surface. The tiles shall be supplied and installed at site through an expert installer including cost of all spacers and other accessories . All samples for tiles shall be approved and before execution.) All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing at all height PVC panel false ceiling of 9mm thick, width of PVC panel 25cm to 30cm and length 2.75m to 3.66m with GI section complete in all respect colour as approved by the Engineer-in-charge. (Make: Heights/Wall Affairs or equivalent.) All complete as per architectural drawings and the direction of engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required ength with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks) The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all Tsections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and laying water proofing treatment with Dr. Fixit FASTFLEX or equivalent with two components polymer modified cementitious coating consisting of cementitious powder and a polymer liquid in two coats for first coat:- clean and saturate surface and then applying a coat of Dr. Fixit - FASTFLEX by maintaining a coverage of 6-7 sft per kg to achieve one mm thickness and the same process shalltended upto 300 mm (three hundred milimeter) vertically.The second coat shall be applied in opposit direction after four six-hours of application of first coat then sprinkle sand on top surface of applied Dr. Fixit-FASTFLEX while still tacky over the second coat. Then Apply cement mortar 1:4 ( one cement: four sand) admoixed with 200 ml (two hundred milimeter) of pidiproof LW @ 200 ml (two hundred milimeter) per 50 kg (fifty kilogram) of cement over the floor with the suitable grediant towards drain pipe, while the second coat of Dr. Fixit is still tacky including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and applying at all floors, heights and locations stone based texture finish suitable for External use of approved make made from natural Granite stone based materials and Bonding agent made from pure acrylic co-polymer emulsion, Broad fungicide and Bonding agent mixed to a recommended quantity of water and applied with a trowels on to the surface, to be finished, in an average uniform coat of minimum 2mm covering an area of about 0.5 sqm/kg of the mix for uniform finish without anu irregularties and discontinous on large surface area giving a uniform surface texture and applied by a trained texture applicators in a single coat. The finish shall be anti fading and non pigmented type with resistance to weathering. Any Grooves and Panels to be formas a part of the design shall deemed to be inclusive in the cost. The texture shall be applied shall be applied over a surface coat of cement primer after duly clearing off any unwanted scratches and undulations by sand papering or using a wire brush before actual application begin complete including cost of all material, labour, machinery, T&P, curing, all leads, lifts and sampling, testing and water arrangements complete as per drawings, requirements, specification and as directed by the Architect / Employer.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing Dead Lock of approved make with 55mm backset, 20mm square forend prepared for euro profile cylinder including strike plate. and EPC 60mm Length one side key operation other side thumb turn and Escutcheons in SS finish complete as per direction of Engineerin-charge with necessary S.S screws etc. complete.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supply & installation of frameless glass Door of size 2100 x 1000 of make with overpanel / sidelight using 12mm thick toughened glass of approved make with die cast patch fitting with stainless steel cover PT 10,PT 20 , PT 24 ,US-10, . pull Handle TGDI-H 450 back to back with 350mm CTC, adjustable fixing for glass ,Length =450mm, 25mm dia, -SS304 Finish: mill , Floor spring BTS 75V with std. spindle and cover plate. As per DIN EN 1154.(500,000 cyle tested ) , Finish: Satin stainless steel. Floor stop half dome with 45mm dia with fixing accessories, in satin Chrome ,Final certifications of products should be submitted be from the product manufacturer for the originality of the product and manufacturer should be have its own service team . The above work complete in all respect as per approved drawings and to the satisfaction of Architect /Engineer-in-Charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supplying of vision glass panels comprising of 6mm vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface #2 of approved colour and shade, all complete for the required performances and the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory of AIS Glass/workshop of approved processor .“(Payment for fixing of glass Panels in the curtain structural glazing is included in cost of fixing of structural glazing “For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. The properties of Glass of AIS Make are Visible Light Transmission (VLT) of 18%, External Reflection 125 %, Internal Reflection 21%, SHGC .32, U. Value 4.5 W/m2 Degree K.. complete as per the architectural drawings and specifications as per the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). The above work complete in all respect as per approved drawings and to the satisfaction of Architect /Engineer-in-Charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 4 mm thick ACP Filler/ cladding inside existing frame, backing or studding with screws or aluminium clips as per location etc. on both sides as per visible areas to be finished as per design and drawing including applicable sealer taping adhesives and hardware accessories complete as per architectural drawings supplied to the complete satisfaction of the Architect / Engineer-in-charge (Frames, to be paid separately).The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Supplying and fixing at site Aluminium Composite Panel cladding of texture and finish as per architecture drawing for interior and exterior of approved make of approved shades made out of 4mm total thickness with top and bottom coil of 0.5mm thick AA3105 Alloy grade produced from direct chill process and following EN 485-2. The top and bottom aluminium coil should be coated in ( SAND finish ) with lead free PVDF (Polyvinyl Diene Fluoride) paint of 70:30 ratio by Double Coat Double Bake method following AAMA2605. The core should be mineral core with minimum 72% inorganic matter passing resistance to fire ASTM E119 for 2 hours and reaction to fire EN13501-1 Class B S1 D0. ). The aluminium composite panel cladding sheet shall be coil coated with approved colour and shade on face 1 and polymer (Service) coating on face 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc., for linear as well as curvilinear portions of the building, for all heights and all levels etc. as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. The grooves shall be filled with approved make of weather sealant (non-staining grade). The base frame work for shall be in aluminium section 50mm x 25mm x 2mm in a grid of 600mm x 600 mm fixed with necessary screws, dash fastners, etc. Framework for ACP cladding is payable under the relevant aluminium items . However, for the purpose of payment, only the actual area on the external face of the clading wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing of 6mm thick Premium lacquered glass of approved make and color by Engineer-in-charge mounted on SGG PLANICLIP (J/J1/I type) or equivalent on a perfectly leveled surface ( MS channel / Aluminum channel ). Lacquered strong glass must be made industrially, opaque , coated with PU lacquer (100 micron thick), color consistency highly durable, humid resistant (conforms to BS EN 1036 1999), environmentally friendly), compressive strenghth (1000 MPa) & tensile strenghth (40 MPa), same as float glass. Post tempering mechanical strength would be increased 4 to 5 times than the annealed glass. Tempering should be done as the EN 12150. Planilaque Strong glasses are to be fixed with a revolutionized system made of safe, eco friendly light weight, ultra strong transparent polymer clips ( Single Sided J1 & J2 Type, Double sided I Type ), white backing foam and grey impact absorbing foam, to accommodate upto ± 10mm substrate undulation, and with a horizontal load capacity of 30Kg/100mm and vertical pullout load > 200kg/100mm, Glass should be supported with 1mm thick lip covering upto 3mm of glass surface, clips should be fixed using durable, non corrosive, strong screw 45mm long. complete in all respects as per drawings, requirements, specification & as directed by the Engineer-in-charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes minimum 2 mm thick, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Preparation of sub grade by dressing to camber (earth work for the cutting involved for sub grade to be paid for separately depending upon the classification of soil) within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and Laying Stone soling properly hand packed filling interstices with manual roller to the required gradient and chamber including spreding,watering and rolling of hiding material moorum or earth etc. as per the direction of Engineer-in-charge including carriage of material in all leads and lifts and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying heavy duty precast cement concrete of NTC inter locking paver blocks vibro compacted upto M-50 (M-Fifty) grade including border or kurb block Grey or coloured over sub-base of concrete with 25mm (Twenty five milimetres) thick average thickness of cement mortar 1:4 (One cement : Four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete (sub-base concrete floor to be paid for separately) within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

80mm (eighty milimetres) thick inter locking paver blocks.

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 1545-2004 of Kitec or its equivalent for water supply including clamps at appropriate spacing, cutting fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work), including filling the joints with approved adhesive complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

1216 (16mm) Sixteen millimeter diameter pipe O.D. pipe

1620 (20mm) twenty millimeter diameter pipe O.D. pipe

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes light grade ISI marked including fixing with approved adhesive etc. complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

75mm (seventy five milimetres) diametres

110mm (One hundred ten milimetres) diametres

Providing and fixing P.V.C. I.S.I. marked plain bend including filling the joints with including fixing with approved adhesive within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

75mm nominal (One hundred fifty milimetres) diameter.

110mm (One hundred ten milimetres) diameters

Providing and fixing P.V.C. Door bend ISI marked including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

75mm (seventy five milimetres) diameter.

110mm (One hundred ten milimetres) diameter.

Providing and fixing P.V.C. Collar ISI marked including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

75mm (seventy five milimetres) diameter.

110mm (One hundred ten milimetres) diametres

Providing and fixing P.V.C. I.S.I. marked cowl 110mm (one hundred ten milimetres) diametres (confirming to BIS-14735-99) ISI marked including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 110 x 90mm (One hundred ten into Ninety milimetres) P.V.C. I.S.I. marked floor trap ISI marked (confirming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing W.C. Of Star S no 20087 (S- 10) of size 57 X 35 X 39 Cm (fifty seven into thirty five into thirty nine centimetre) of Hindware /Cera/ Jaquar of star white / snow white shade vitreous china wash down closet (European type W.C. pan) with internal P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement isto one sand) (seat and cover to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing PVC coloured/white with (dual flushing system) 10.00 Ltrs (Ten litres) capacity low level flushing cistern (Sleek Plus) Hindware/cera/Jaquar of star white / snow white shade with fittings such as lead valve less siphon, 15mm (Fifteen milimetres) nominal size PVC ball valve with polythene float, with flush buffor, unions and couplings for connection with inlet, outlet and over flow pipe, 40mm (Forty milimetres) diametres C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing G.I. inlet connection pipe for each flush pipe with W.C. pan within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing plastic seat solid type and cover of Hindware/cera/Jaquar of star white / snow white shade for wash down water closet with C.P. brass hinges and rubber buffers (white plastic seat and cover) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing flat back No of 60002 of size 390 x 375x590mm (three hundred ninety into three hundred seventy five into five hundred ninety milimetres) size Hindware / Jaquare of star white / snow white shade vitreous China urinal including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separatelywithin all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 600x300mm (Six hundred into Three hundred milimetres) vitreous china division plate for urinals of Hindware /cera/Jaquar of star white / snow white shade within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china wash basin Matrix of Cera / Hindware 55x40 cm (fifty five into forty centimetre) with single hole for pillar tap with pedestal including C.I. or M.S. brackets, painted white including cutting holes and making good the same but excluding fittings within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres M.I. union for wash basin or sink.complete within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres C.P brass waste for wash basin and sink of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal waste for wash basin or sink complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimetres) diametres C.P. Grating Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal for gully floor or Nahni trap within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty milimetres) beveled edge mirror of modiguard / autal / Galdin fish or superior glass mounted on 6mm (Six milimetres) thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 600x20mm (Six hundred into Twenty milimetres) C.P. brass Towel rail of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal.brackets fixed to wooden plugs within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 600x120mm (six hundred into one hundred twenty millimetre) glass shelf of Modi guard / flout / sant gobind / Aashai Hindon series of jal with C.P. brass. (Heavy duty makes ISI marked) brackets and guard rail complete fixed to wooden plugs with C.P. brass screws within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass toilet paper holder of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of jal as per direction of Engineer-in-Charge, within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing C.P. jet spray of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal of approved quality and colour with one metre tube within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre nominal bore chromium plated ISI marked fancy bib tap of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) diametre C.P. stop cocks of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) diametres C.P. brass pillar tap with capstan Head of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) diametres C.P.brass angle valve without nuts of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per approved drawing and design directed by the Engineer-in-Charge within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass full way valve with wheel, of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore PVC connection pipe with brass union 45cm (Forty five Centimetres) length within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing PVC waste pipe for wash basin, sink including check nut within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and placing water tank make P.V.C. SINTEX or equivalent having capacity of 2000 (two thousand) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (one Cement isto five Sand isto ten graded stone aggregate 40mm (forty millimetre) nominal size bedding 150mm (one hundred fifty millimetre) for PVC pipes of the following internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8 (One cement isto Four sand isto Eight graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including C.I. cover with frame (light duty single seal pattern -I) 450x610mm (Four hundred fifty into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (Twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8 (One cement isto Four sand isto Eight graded crushed/broken stone aggregate 40mm (Forty milimetres nominal size) inside plastering 15mm ( Fifteen milimetres) thick with cement mortar 1:3 ( One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement: Two sand isto Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 1.00 mtrs(One metre) deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs(twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred milimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5(One cement: Five sand) C.I. cover with frame(light duty) 455x610mm(Four hundred fifty five into Six hundred ten milimetres)internal dimensions total weight cover and frame to be not less than 38Kgs (Thirty eight Kilograms) weight of cover 23 Kgs (twenty three kilograms)and weight of frame 15 Kgs (Fifteen kilograms) RCC top slab with 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres nominal size) foundation concrete 1:5:10 (One cement: Fiver sand: Ten graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm ( Fifteen milimetres) thick with cement mortar 1:3 ( One Cement: three sand) finished with a floating coat of neat cement on walls and bed concrete etc. complete inside dimensions 455x610mmx450mm (Four hundred fifty five into Six hundred ten into Four hundred fifty milimetres) deep within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composit end seal compression fitting as per IS-1545-2004 for cold water supply e.g. tees, elbows, reduser,connceters,couplers and claps jointing testing and fitting complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing & fixing Kitec/ Kisan Equal Tee (1620)

Providing & fixing Kitec/Kisan Female Elbow 1620 X15 mm)

Providing & fixing Kitec/Kisan Female branchTee.(1620X1620X20mm)

Providing & fixing Kitec /Kisan Female Elbow (1620 X15 mm)

Providing & fixing Kitec / KisanMale Thread Connector (1620X15mm)

Providing and laying in trenches, galvanized mild steel tubes (light, medium and heavy grade), tube fittings (earth work in trenches to be measured and paid separately). (external work) :-65 mm within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing & installing 3 BHP pumping set including all accessories for boosting arrangements on water supply line to fill the terrace tank.within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 1500 mm x 450 mm beveled edge mirror of superior glass mounted on 6 mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screws and washers within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and Fixing in position C.P brass 32mm size Bottle trap of approved quality x make as per approved by engineer in charge.within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing square-mouth PVC gully trap with Pvc grating of size 160 x 110 mm complete with brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design complete in all respect to complete Satisfaction of Engineer-in-charge:With Fly ash lime bricks (FALG Bricks) conforming to I.S. 12894. Astral/ Supreme/Finolex or equalent make size 110 x 110 mm Cat no.M142003409 within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing & fixing of white vitreous china below counter oval wash basin (425X550X195 mm) with CP brass waste assembly, wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge. (Jaquar cat no. FLS-WHT-5701 /Hindware Cat no. 10080 /Kohler Cat no. K-2215IN-O) within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing in position Straight Grab Bar(Dia.38mm Length 692mm Two Wall Horizontal and Swing Up Grab Bar complete with all accessories and fitting complete as per direction of the Engineer in Charge within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. Straight Grab Bar (Jaquar Cat no.BR0600CS or approved equivalent) Swing Up Grab Bar(Jaquar Cat no.BG0800CS or approved equivalent) Two Wall Horizontal Grab Bar (Jaquar Cat no.BAD090CS or approved equivalent)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.complete as per direction of the Engineer in Charge within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete 75mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete 110mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and fixing PVC single Y-junctions ISI marked including fixing with approved adhesive etc. complete 75mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and fixing PVC single Y-junctions ISI marked including fixing with approved adhesive etc. complete 110mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete. 75 mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete. 110 mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

Providing and laying (to level or slopes) and jointing with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 sand) salt glazed stoneware pipes grade 'A' of the following internal diameters including testing of pipes and joints complete:

150mm dia pipe.

200mm dia pipe.

Providing and laying cement concrete 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate 40mm nominal size )surround or encasing stoneware pipes of the following internal diameters, including bed concrete, necessary form work and curing complete 150 mm dia within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government

150mm dia pipe.

200mm dia pipe.

SS CONSTRUCTION COMPANY