PROVN OF CETAIN LBW, SPECIAL REPAIR AND REVENUE WORKS AT MIL STATION BEAS and JANDIALA GURU UNDER GE KAPURTHALA

Amount

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed by Engineer-In-Charge.

M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregates) as in plinth protection etc, finishing cement concrete surface even and smooth with out using extra cement including making joints with hot bitumastic filing in proportion of bitumen and sand 1:2, complete all as specified and directed by Engineer-In-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed by Engineer-In-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work & precast concrete articles, complete all as specified and directed by Engineer-In-Charge.

M&L for brick work with sub class old size 'B' bricks, straight or curved on plan, exceeding 6m mean radius, built in cement mortar 1:6, complete all as specified and directed by Engineer-In-Charge.

-ditto- all as per item No 05 above but except bricks etc, complete all as specified and directed by Engineer-In-Charge.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls finished even and fair, complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls finished even and fair, complete all as specified and directed by Engineer-In-Charge.

M&L for 15mm thick plaster in two layers (10mm+5mm) rendering in cement mortar 1:4 on other than fair faces of brick work and finishing surface even and smooth without using extra cement, complete all as specified and directed by Engineer-In-Charge.

M&L for 10mm thick rendering in cement mortar 1:3 on ceiling surfaces, finished surface even and smooth without using extra cement, complete all as specified and directed by Engineer-In-Charge.

M&L for 5mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over and including a coat of chalk whiting/priming on plastered surfaces of walls, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces and distempering walls with two coats of distemper oil emulsion, white or tinted over and including 1mm thick wall care putty including primer, complete all as specified and directed by Engineer-in-charge.

M&L for three coat of white wash on plastered/unplasterd surface on ceiling including preparation of new plastered surface, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of Newly plastered surfaces and applying two coats of white wash over a coat of chalk whiting/priming on plastered surfaces of walls etc. Complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new plastered surfaces of walls etc. and applying two coats of distemper oil emulsion over and including 3mm thick wall care putty preparatory to distemper, complete all as specified and directed by Engineer-In-Charge.

Dismantling of AC sheets roof covering, complete all as specified and directed by Engineer-In-Charge.

S&F, Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheets, 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-In-Charge.

S&F, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheets, 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge, etc. fixed with self tapping screws, complete all as specified and directed by Engineer-In-Charge.

Dismantling wall and celling board (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets, complete all as specified and directed by Engineer-In-Charge.

Demolition of wall and ceiling board (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets, complete all as specified and directed by Engineer-In-Charge.

M&L for armstrong make ceiling framework with using 9mm thick gypsum based ceiling tiles with wheather resistance face on back side and vinyl finish on the front fixed in 24mm GI armstrong frame work of grid 600x600 mm size, the members of snap grid frame work of GI/Steel section of 24mm wide with T-flanges, channels etc of white colour having rotary stiching on all members, i.e main runner, 1200x600mm cross tee galvanised with minimum thickness of 120 gms per/sqm passed through 500 hrs test and hanging the same with existing roof members such as rafters, pulins or other wooden members particularly provided for hanging pupose using 8mm dia mild steel bar of required length fixed with nut bolt of 50mm long and 10mm dia of neck with washer flat iron 50x6mm thick clamps etc to wooden members, complete all as specified and directed by Engineer-In-Charge.

Supply & fix 6 to 7mm thick gypsum board laminated on both sides for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid, complete all as specified and directed by Engineer-In-Charge.

Supply & fix anodised aluminium snap grid frame work of size 605 x 605 mm with aluminium T section of size 38x25x1.5mm thick for main runner, 25x25x1.5mm thick for cross runners and angle of size 25x25x1.5mm thick along the walls suspended with & including 4mm dia galvanised mild steel wire (as in suspenders of ceiling members) for false ceiling including necessary notching & prepared holes, complete all as specified and directed by Engineer-In-Charge.

S&F, 4 mm thick, Non asbestos fibre cement building boards fixed to timber/GI/Aluminium framework with screws as in ceiling, complete all as specified and directed by Engineer-In-Charge.

M & L for preparing new surfaces of ceiling and applying three coats of white wash, complete all as specified and directed by Engineer-In-Charge.

Dismantling taking down framed trusses of span not exceeding 10m, complete all as specified and directed by Engineer-In-Charge.

Dismantling mild steel work of any description, complete all as specified and directed by Engineer-In-Charge.

Erection and fixing only steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240. Complete all as specified and directed by Engineer-In-Charge.

Errection and fixing rolled mild steel Fe 410-W (Gde-E-250) quality-A in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Complete all as specified and directed by Engineer-In-Charge.

Erection and fixing only steel tubular work as in purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed by Engineer-In-Charge.

S&F rolled mild steel Fe 410-W (Gde-E-250) quality-A in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated), complete all as specified and directed by Engineer-In-Charge.

S&F Roof truss/Framed works of Mild steel Fe-410(W) Gde-E-250, quality 'A' as in purlins, crane grantries, rails and fastening and heavy brackets framing Beam( of tee,angle, pipes of flat section , base plates etc) incluidng distance pieces. Complete all as specified and directed by Engineer-In-Charge.

Supply & Fixing mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240. Complete all as specified and directed by Engineer-In-Charge.

Supply & Fixing for rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with out any attachment conforming to Fe:410-W(Gde-E-250 ) quality-A. Complete all as specified and directed by Engineer-In-Charge.

S&F rolled sections(angle, tee, square pipe, plate etc) as in main and crossed beams , posts, hip and rafters etc, fixed with angle cleats or other connecting plates, rivets ,nut bolts and or welding etc, conforming Fe 410W (Gde E-250) Quality B. Complete all as specified and directed by Engineer-In-Charge.

S&F MS Pipes as in vertical posts, fixed with angle cleats or other connecting plates, rivets ,nut bolts etc, conforming Fe 410W (Gde E-250) Quality B. Complete all as specified and directed by Engineer-In-Charge.

S&F mild steel screw bolts (machine made) with hexagonal or Square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, exceeding 5 cm but not exceeding 10 cm long, dia of shank 10 to 15 mm, complete all as specified and directed by Engineer-In-Charge.

M&L for welding in repairs not exceeding 2.5 cm in length to the metal not exceeding 6mm thick, complete all as specified and directed by Engineer-In-Charge.

Taking down chowkats or frames with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames), complete all as specified and directed by Engineer-In-Charge.

Taking down chowkats or frames with shutters exceeding 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frames), complete all as specified and directed by Engineer-In-Charge.

M&L for framed work as in door or gates of angle or other section with gusset plate, rails brases etc, complete drills for fixing of steel sheeting or other covering door etc, ( Gde Fe 410-0-0 or Fe-310-0). Complete all as specified and directed by Engineer-In-Charge.

S&F mild steel framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors hung as gates, including pintle hinges, stops, hand made sliding bolts, etc and similar work conforming to Fe 290(Gde E-165). Complete all as specified and directed by Engineer-In-Charge.

S&F, 30 mm thick, 2nd class hardwood Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides supplied & fixed to chowkats, complete all as specified and directed by Engineer-In-Charge.

S&F, 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied & fixed to chowkats, complete all as specified and directed by Engineer-In-Charge.

S&F 2nd class hard wood 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engineer-In-Charge.

S&F 2nd class hard wood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed by Engineer-In-Charge.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commerial type of one side and another face is covered with aluminium sheet, 0.5mm thick, fixed with aluminium alloys screws, complete all as specified and directed by Engineer-In-Charge.

S&F 150 mm long aluminium analized cast type handle, complete all as specified and directed by Engineer-In-Charge.

S&F 125 mm long aluminium analized cast type handle, complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel pressed handles of size 150mm, oval type, stove enamelled black, complete all as specified and directed by Engineer-In-Charge.

S&F aluminium anodised handle extruded section of size 150mm all as specified and directed

S&F Aluminium anodised barrel tower bolt of extruded section 200mm long, complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel barrel tower bolts 200mm long, stove enamelled black, with bright bolt and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F 100mm long MS butt hinges medium weight colled rolled fixed welded to angled iron frame, complete all as specified and directed by Engineer-In-Charge.

S&F 250mm long mild steel sliding door bolts plate type stove enmelled black with bright bolt not less than 12mm dia with and including a minimum 8 bolt and nuts four on bolt plate & two on staple plate, complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F Aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F, mild steel 300mm , ordinary rat tail rod pattern spring including roller and roller plate and necessary welding, complete all as specified and directed by Engineer-In-Charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Glass and painting shall be measured and paid separately under appropriate item etc. Complete all as specified and directed by Engineer-In-Charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note : Wire mesh and painting shall be measured and paid separately under appropriate item etc. Complete all as specified and directed by Engineer-In-Charge.

S&F figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pane, complete all as specified and directed by Engineer-In-Charge.

S&F, Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with tinned tacks, or stainless steel wire staples, complete all as specified and directed by Engineer-In-Charge.

Supply only Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed by Engineer-In-Charge. (Note :Fixing charges are deemed to be included in serial item No. 62 and or 63).

Supply only 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane, complete all as specified and directed by Engineer-In-Charge. (Note :Fixing charges are deemed to be included in serial item No. 62 and or 63).

Supply only 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane, complete all as specified and directed by Engineer-In-Charge. (Note :Fixing charges are deemed to be included in serial item No. 62 and or 63).

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer. Complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new wood surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer, complete all as specified and directed by Engineer-In-Charge.

S&F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 , complete of any M.S. section all as specified and directed by Engineer-In-Charge.

S&F floor door stopper 140mm of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor, complete all as specified and directed by Engineer-In-Charge.

S&F floor door stopper, overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engineer-In-Charge.

M&L for 100mm thick, plain cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregates) as in floor & finishing the surfaces even & smooth with using extra cement, complete all as specified and directed by Engineer-In-Charge.

M&L for plain cement concrete, 100mm thick (1:2:4), type B-1, (using 40mm graded stone aggregate ) in sub floors, sub bases, floors and pavings etc. Complete all as specified and directed by Engineer-In-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, complete all as specified and directed by Engineer-In-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over and including 20mm thick cement screed base in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by Engineer-In-Charge.

-Ditto- all as per item No 80 above but except stone. Complete all as specified and directed by Engineer-In-Charge.

M&L for kota stone slab 20-25mm thick in riser of steps, skirtings, dado and pillar, laid over and including 15mm thick cement screed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by Engineer-In-Charge.

Ditto all as per item No 82 above but except stone. Complete all as specified and directed by Engineer-In-Charge.

M&L for grinding and polishing the old kota stone flooring/skirting with machine grinder and treating the surface with bees wax polish, complete all as specified and directed by Engineer-In-Charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, over and including 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-In-Charge.

-Ditto- all as per item No 85 above but as in skirtings laid over and including 10mm thick rendering in cement mortar (1:4), complete all as specified and directed by Engineer-in-Charge.

M&L for joint free coloured glazed ceramic tiles of size 350x250x7mm/450x350x7mm thick, as on vertical surfaces such as dados, skirtings etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour of tiles over and including backing coat 10mm thick cement mortar (1:4), complete all as specified and as directed by the Engineer-in-Charge.

M&L for cement concrete (1:2:4) B-1 using 20mm graded stone aggregate as in lintels up to 1.5 m clear span, benching, coping, bed blocks and roof kerbs etc including use of necessary form work, complete all as specified and directed by Engineer-In-Charge.

M&L for reinforced cement concrete (nominal mix), type B-1, 1:2:4(20mm graded aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) as in chajjas, complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to chullah hoods, Chajjas, troughs and similar items including edges, complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to. Complete all as specified and directed by Engineer-in-Charge.

-Ditto- all as per item No 93 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders. Complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 Type B1 ( 20 mm graded stone aggregate) as in bed blocks, coping, etc. Complete all as specified and directed by Engineer-in-Charge.

M&L for steel curtain rod of 25mm dia, powder coated having wall thickness 1mm, with aluminium powder coated brackets fixed to wall with screws, gutties @ 1500mm C/C (approx) and curtain rings (Minimum 5 Nos rings per running mtr of curtain rod) including taking out the existing old pelmet box along with old curtain rods and removing, complete all as specified and directed by Engineer-in-Charge.

S&F harrison rails, curtain rod of mild steel, chromium plated with fixing brackets, stops, rollers etc. Complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches in any type of soil not exceeding 1.5m wide and not exceeding 1.5 m depth for foundation & getting out, complete all as specified and directed by Engineer-in-Charge.

Surface excavtion not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed by Engineer-in-Charge.

Surface excavation not exceeding 30cm deep and avg 15cm deep and getting out in hard/dense soil, complete all as specified and directed by Engineer-in-Charge.

Surface dressing not exceeding 15cm deep and getting out in soft/loose soil. Complete all as specified and directed by Engineer-in-Charge.

Excavation in post holes(or similar holes ) each not exceeding 0.50 Cum, and getteing out, returning filing in and ramming earth with broken rubble mixed with earth around in layers not exceeding 25cm, watering etc and removing surplus soil not exceeding 50m and making good surface in loose/soft soil, complete all as specified and directed by Engineer-In-Charge.

Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm for soft/loose soil, complete all as specified and directed by Engineer-in-Charge.

Filling good earth including spreading, levelling, watering and well raming in layers n exc 25 cm thick each layer complete all as specified and directed.

Removing excavated materials (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point. Complete all as specified and directed by Engineer-in-Charge.

M&L for Hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed by Engineer-in-Charge.

M&L for hardcore of broken stone or bricks guage exceeding 63mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rolled/rammed to a true surface true surface. Complete all as specified and directed by Engineer-in-Charge.

M&L for hardcore of broken bricks of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base of footpath complete, complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete interlocking paver block, 80mm thick, any shape and size, confirming to IS-15658-2006, M-35 Grade, with grey cement and no pigment complete all as specified and directed. Make:Supertile.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness M-50 grade with grey cement and pigment complete all as specified and directed by Engineer - in - Charge.

M&L for cement concrete type E2, 1:5:10 as in foundations, filling and mass concrete, complete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete type C-2, 1:3:6 (40mm Graded agg) as in foundation, filling and mass concrete, complete all as specified and directed by Engineer-In-Charge.

M&L for sand filling under floor or in foundation including watering and consolidation, complete all as specified and directed by Engineer-in-Charge.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed by Engineer-in-Charge.

M&L for 100 mm thick cement concrete 1:4:8 type B–2 using 40mm graded stone aggregates as in flooring finished even and smooth without using extra cement all as specified and directed by Engineer-in-Charge .

M&L for 100 mm thick plain cement concrete 1:2:4 type B–1 using 20mm graded stone aggregates as in flooring/hardstanding finishing the surface even and smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M&L for 25 mm thick Damp proof courses to horizontal or vertical surfaces in cement concrete 1:2:4, Tye B-0 including necessary formwork, complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound, complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick cement concrete type D-2, 1:4:8 as in Subbase flooring, complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick cement concrete type B-1, 1:2:4 as in flooring, finishing surfaces even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L for 3mm thick glass dividing strips 38 mm wide, inserted in postion confirm to design, complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete (1:4:8), type D-2, (using 40mm graded stone aggregates) in foundations, filling, mass concrete etc. Complete all as specified and directed by Engineer-in-Charge.

M&L for design mix M-25 concrete (using 20mm graded stone aggregate), as in Foundations, including rafts, footings, foundation beams; plinth beams; base for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engineer-in-Charge.

M&L for Design mix M-25 concrete (using 20mm graded stone aggregate), as in Columns, pillars, piers, posts and struts, complete all as specified and directed by Engineer-in-Charge.

M&L for Design mix M-25 concrete (using 20mm graded stone aggregate), as in roof beams, cantilevers, bressummers, lintels upto and over 1.5 m clear span complete all as specified and directed by Engineer-in-Charge.

M&L for RCC design mix M-25 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed by Engineer-in-Charge.

M&L for RCC design mix M-25 (using 20mm graded crushed stone aggregate) as in suspended chajjas and the like, complete all as specified and as directed by Engineer-in-Charge.

Use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges, complete all as specified and as directed by Engineer-in-Charge.

Use and waste formwork to square/reactangular sides of pillars, posts, struts, piers, columns, and stanchions fair and finished surface, complete all as specified and directed by Engineer-in-Charge.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed by Engineer-in-Charge.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and as directed by Engineer-in-Charge.

Use and waste formwork to sides and soffits of floor or roof beams, beam, RCC coping fair and finished surface, complete all as specified and directed by Engineer-in-Charge.

M&L for fly ash brick work Old size bricks in cement mortar , straight or curved on plan, exc 6m mean radius, built in cement mortar 1:6,complete all as specified and directed by Engineer-in-Charge.

M&L for pre-construction antitermite treatment by treating the bottom and sides of excavation at the rate of 5 litres of ATT emulsion per Sqm of surface area, complete all as specified and as directed by Engineer-in-Charge.

M&L for pre-construction antitermite treatment by treating the back fill in contact with foundation at the rate of 7.5 litres of ATT emulsion per Sqm of vertical surface area in contact, complete all as specified and as directed by Engineer-in-Charge.

M&L for pre-construction antitermite treatment by treating the top surface of filled earth at the rate of 5 litres of ATT emulsion per Sqm of surface area, complete all as specified and as directed by Engineer-in-Charge.

M&L for pre-construction antitermite treatment by treating the soil under plinth ptotection at the rate of 5 litres of ATT emulsion per Sqm of surface area, complete all as specified and as directed by Engineer-in-Charge.

M&L for pre-construction antitermite treatment by treating the soil alongwith external perimeter of bldg at the rate of 2.25 litres of emulsion per metre of the wall, complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new concrete surface and apply water proofing treatment to roof with APP (Atactic poly propylene) modified prefabricated five layer 3mm thick water proofing membrance super therolay of STP limited wth non-woven polyster male reinforcement of 160gm, weight of membrane @3.6kg/sqm over a solvent based bitumen primer, shalitex primer @ 0.3 lt/sqm by the same manufacturer conforming to IS-3384-1986.Apply two coat of alumnium paint on top of membrane surface after laying the membrane incl all cleaning Note : The membrane shall be laid using butane torch. The end lap should be 100 mm and the side lap must be minimum 75 mm. The membrane shall be first laid upto the parapet wall junction and then shall be overlapped with naother membrane (flashing) with and overlap covering upto a distance of 300mm. In case of parapet height is less than/ upto 500 mm membrane shall be terminated at the top of parapet. (Water ponding test should be carried out for 72 hrs of water proofing treatment).

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified.

S&F powder coated Anodised aluminium frame (Thickness of powder coating not less than 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. Complete all as specified and directed by Engineer-in-Charge.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified.

S&F 5.50mm thick sheet glass, ordinary quality and glazing with beads fixed with metal panel pins with solar control dil 25micron reflective type sicked to glass panes as per instruction of manufacturers, complete all as specified and directed by Engineer-in-Charge.

S&F aluminium (extrutded section) door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinge type B-21 100mm long (2 Nos) suitable handle (1 No.), complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified in SSR 2010, Part-II and as directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of tube for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top, lock and bottom railson either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in MS frames welded/sealed to the styles and rail with suitable PVC sheet /sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed by Engineer-in-Charge.

S&F brass chromium plated single towel rail 20mm dia, D type, 600mm long between flanges as per cat part No AKP-35711P of Jaquar fixed with and including chromium plated brass screws and wooden/plastic cleats, fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F, brass CP central hole, cast copper alloy (ISI Marked) fancy type chromium plated for mixing hot and cold water screwed down high pressure with capstan head screwed both ends basin mixer with copper pipe complete all as specified and as directed by Engr-in-Charge.

S&F in repair for fancy type chromium plated stop valves, cast (angle cock) copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for bore of size 15mm, complete all as specified and as directed by Engineer-in-Charge.

S&F stop valves, cast copper alloy, bore dia of pipe in 15mm, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed but fancy type, Chromium Plated with long shank and cup (concealed type) etc. Complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore chromium plated stop valves/angular valve, cast copper alloy, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe and fixed complete all as specified and directed. (Cat part No -QQT-7053 of Make: Jaquar).

S&F vitreous China Ware Wash hand basin white, flat back, size 210x580x460mm size with long padestal, 32mm dia stainless steel waste coupling of Make Jaquar (Cat Pt No ALD-705L130) & cast iron Brackets including cutting for and pinning ends of brackets or erecting stand complete. Make Jaquar solo Cat Pt No (SLS WHT)0572+1510 complete fixed in repairs all as specified & directed.

S&F coloured toilet paper holder CP fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. (Cat Part No CAN-1153N Make Jaquar)

S&F hand shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish and Wall Hook with N.R.V (Back Flow Preventer) with clamp (Cat Part No. ALD-CHR-563 of Marc or equivalent of Jaquar), complete all as specified and directed by Engineer-in-Charge.

S&F soap dish, stainless steel approximate size 160x160x90mm fixed to wall with chromium plated brass screws fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F, sheet glass shelf (450mm long) assembly consisting of 8mm thick sheet glass shelf 15 cm wide with chromium plated bracket guard and railing fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F corner glass shelf (300mm long) assembly consisting of 8mm thick sheet glass shelf with chromium plated bracket guard and railing fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F SDG Frameless Beveled Mirror for Bathrooms Wall and Home, 18x24 Inch (Silver) and 5mm thick looking mirror, Beveled Edge at 0.75 Inch Edge thickness 4mm, fitted to wooden plug with CP screws. Complete all as specified and as directed by Engr-in-charge. Make. Saint Gobain/Modi Guard Ultra Mirror.

S&F Stainless Steel Soap Dispensers with bracket complete all as specified by Engineer-in-Charge.

S&F in repair Coupled Closet WC colour, Bowl for Coupled WC with UF soft close slim seat cover, Hinges, Fixing Accessories and Accessories Set. Size 380x660x765mm (CAT Part No LYS-WHT-38751S250UFSM) and Cistern with cistern fittings (CAT Part No: LYS-WHT-38201) of Make Jaquar (Product Code LYS-WHT-38751S250UFSM + LYS-WHT-38201) complete all as specified and as directed by Engineer-in-Charge.

S&F Handy Folding Stainless steel Towel Rack-24 Inches with chromium plated bracket complete all as specified by Engineer-in-Charge.

S&F Towel ring Code No AEC-1121 ( Make Jaquar), complete all as specified and directed by Engineer-in-Charge.

S&F Towel rack Code No AEC-1181 ( Make Jaquar), complete all as specified and directed by Engineer-in-Charge.

Supply and fix 6mm thick PVC hollow wall paneling plain/coloured/printed fixed with screws to wall and corner, edges of panels be sealed with approrite arrangement, colour and pattern as approved by Engineer-in-Charge. Complete all as specified and as directed by Engineer-in-Charge.

Taking up or down, steel tubing 15mm bore and connections and removal from site complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 15mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floors complete all as specified and directed by the Engineer-in-Charge.

Taking up or down, steel tubing 20mm bore and connections and removal from site complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 20mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floorscomplete all as specified and directed by the Engineer-in-Charge.

Supply and fix in repairs; 15mm bore PVC connection and 45cm long with two Nos of brass check nuts and washers complete all as specified and directed by the Engineer-in-Charge.

Taking down carefully aluminium point wiring on casing caping/through conduit (light fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, box type tube light fittings, removing the materials from site except fittings etc which shall be reused in the work and making good the disturbed surfaces of walls/ceiling/ floors etc complete all as specified and as directed by Engineer-in-Charge

M & L for point wiring for one light or one fan point controlled by one switch or with one switch and regulator with PVC unsheathed single core multistranded copper conductor (FRLS) cable of size 1.5 Sqmm (nominal area) in and including PVC conduit 20 mm bore by cutting chases in wall by cutter and making good the surface in cm 1:3 and to the original specification and cast iron /pressed steel concealed terminal boxes including providing 3mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated copper conductor (FRLS) cable of size 1.5 sqmm with green insulation as earth wire and connected to earth dolly complete all as specified. (Switch/Socket outlet to be measured & paid for separately). Make of cable: Finolex/Anchor/Havell’s

-Ditto- all as per Srl item No 174 here in before but for 3 pin socket outlet 5 Amps on same board .

-Ditto- all as per ser item 174 above but for 3 pin socket out let 5 Amps on independent board

-Ditto- all as per srl item No 174 here in before but for 3 pin socket outlet 15 Amps on independent board with PVC unsheathed copper conductor cable of size 2.50 Sqmm including copper earth wire of size 2.50 Sqmm and connected to common earth dolly complete all as specified. (Switch/socket to be measured & paid for separately)

Supply & fixing switch piano flush type 5 Amp single pole one way.

Supply & fixing switch piano flush type 15 Amp single pole one way.

Supply & fixing socket outlet 5 pin 5 Amps flush type multipurpose.

Supply & fixing socket outlet multipurpose 2 in one, 3 pin 5/15Amps flush type.

Taking down old unserviceable FTL fitting 36/40Watt and S & F surface mounting energy saving LED tube light fitting/ Batten with LED T8 Tubelight with PC body, 1x20W, 230V , Cat Part No of Batten DMLN1LT8-16 & Cat Part No LT8-20-865-2 for LED T8 Tube light Make- Crompton or equivalent complete with all accessories.

Supply and fixing MCB single pole 6 to 32 Amps 240 Volts, B Series Product Code CSMBS1B6 to CSMBS1B32 Make- C&S or equivalent in Havells/GE/ L &T/Legrand

Supply and fixing MCB single pole 32 Amps 240 Volts SPN , B Series Product Code CSMBS1B6N to CSMBS1B32N Make- C&S or equivalent in Havells/GE/L&T/Legrand)

Supply & fixing sheet metal enclosures DB Single Pole and Neutral 4 way with double door, detachable gland plates flush/ mounting for MCB’s fitted with bus bar, earth wire, 220 volts including taking down of existing DB at site all as specifed and directed.. Make-Havells/L&T/Indo Asian

Supply & fixing sheet metal enclosures DB Single Pole and Neutral 2 way with single door, detachable gland plates flush/ mounting for MCB’s fitted with bus bar, earth wire, 220 volts. Make-Havells/L&T/Indo Asian

Supply & fixing sheet metal enclosures with double door, detachable gland plates flush/ mounting for MCB’s fitted with bus bar, earth wire and neutral link, 8 ways, 240 volts. ( Make- Havells/Legrand)

Supply & fixing ceiling rose surface bakelite 65 x 50mm three terminal complete all as specified and as directed by Engineer-in-Charge. Make – Anchor/Leader/Bajaj

Supply & fixing Angular lamp holder insulated body with back plate suitable for batten fittings including 1 x 9 W LED Lamp Make- Havells LED ADORE 9 W B22 WW 3 STAR LAMP Cat No LHLDEUEEMC8R009 or equivalent all as specified and directed by Engr in Charge.

Hanging only ceiling fan retrived from Srl No 173, and connecting up including provision of flexible copper conductor cable from ceiling rose / connector to fan and GI pipe/ steel rod, nuts, bolts, clamps etc as required at site all as specified and directed by Engr-in-charge.

Supply & fixing fan regulator electronic step type and making connections. (Make : Anchor/Leader/Bajaj).

Supply & fix ceiling fan complete with electronic type regulator of 230 V,1200 mm sweep with all accessories complete all as specified and diretced by Engr in ChargeMake- Bajaj/Crompton/ Orient/Polar or equivalent

M&L for earthing complete with galvanized steel earth plate trode 60cm x 60cm x 6mm thick buried directly in ground vertically in a pit not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below level connected to GI earth wire 4mm dia by means of bolts, nuts and washers (earth plate covered with charcoal dust and common salt in alternate layers) GI earth wire protected by galvanized steel pipe light grade of 15 mm dia upto switch board and connected to main switch board, including provision of 20mm dia GI tubing light grade watering pipe with funnel and wire mesh PCC earth pit (1:3:6) type C-1 covered with CI cover hinged with frame including excavation and earth work complete all as specified and shown in electrical plate No 5 of SSR Part I including testing on completion.

Disconnecting and taking out old unserviceable cable of service connection/sub main wire of any size and type from pole to DB's / Main switch complete all as specified

Supply and fixing in replacement sub main wiring with two single core FRLS insulated cable with copper conductor stranded and sheathed of size 6 Sq mm in and including PVC conduit including 1 x 6 Sq mm FRLS copper earth wire to common earth and connected to earth dolly complete all as specified and directed. Make of cable : Finolex/Havells/Plaza/Indo Asian

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for ltaking out old cable/laying of under ground cable/foundation of poles/stays including segregation of old serviceable bricks, complete all as specified and directed by Engineer-in-Charge.

Supplying and laying bricks as protection using old size sub class 'B' bricks, laid flat dry but adjoining to each other laid lengh wise perpendicular to the axis of cable complete all as specified and directed.

Supplying and laying in trenches sand cushioning 8 cm below and 15 cm above the cable for under ground cable complete all as specified & directed. (Note : Depth of thickness of sand 18cm after punning down shall be increased, recorded & paid)

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core. Complete all as specified and directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core.

Supply and fixing LED bldg security light fitting 15 watt Powder coated pressure die cast aluminium compact LED security light including 1.5 mtr long 40 mm bore GI pipe mounting bracket made to shape for fixing on wall with 40 mm x 6 mm flat iron clamp 02 numbers with 16 mm dia bolts, nuts and washers all as specified and directed by Engineer-in-Charge.Make- Crompton Cat Part No LSTS-15-CDL or equivalent in Bajaj/Philips/C&S/Havells : Contractor shall provide 1 years written manufactures warranty for the LED fixture complete including driver from the certified date of completion.

M&L for GI Pipe 'light grade' galvanized of bore size 40mm with all fitting laid in trenches/on pole/road crossing of size 40mm

S&F 1100 Volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4 mm suspension wire, one twin core cable flat or round of 10 sqmm cable including GI wire , bobins, insulator for stay and hanging,complete all as specified and directed by Engineer-in-Charge.

S&F House service bracket (Hook type) complete with 3.0 Mtr long G.I pipe 40mm dia Medium grade two Nos 90 degree bends, MS hooks and stay or guy, complete all as specified and directed by Engineer-in-Charge.

SUNRISE CONSTRUCTION COMPANY