SPL REPAIR TO 06 QTRS AT GYM ROAD UNDER GE CENTRAL DELHI CANTT 10

Amount

Dismantling of water tank of any type/pattern exc 250 ltr but n exc 500 ltr capacity and removing from site

Rotational moulded polyethylene water storage tank tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, connecting to inlet and outlet pipe connections, with and including 20mm dia GI wash out with plug, complete all as specified and directed.

Complete removal exising old surfaces of wall by scrubbing with hard brushing, brooming down or steel wire brushing scraping down smook root mould moss and efforescent salts and treating oil and greasy spots as applicable and washing with water and applying 2-3 mm wall care putty and apply two coat oil bound distempr over one coat of primer from the same manufacturer complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for old plastered surfaces of wall and applying two coats of white wash complete all as specified and directed.

Taking down cement plaster of any description on brick stone or concrete walls surfaces including raking out joints hacking for keys scrubing down with water etc complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of walls surfaces finished even and smooth without using extra cement up to hieght of four storey ,including scaffolding complete.

M&L for rendering 15mm thick in CM 1:6 on other than fair faces of brick/stone masonary brick work or concrete surfaces of walls firnished even and smooth without using extra cement in multistorey building ,complete all as directed

M&L for 5mm thick rendering in cement mortar 1:3 finished even and smooth surface without using extra cement on ceiling, chajja in double storey building etc, complete all as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distermper over a coat of primer including 2-3 mm thick wall putty complete all as specifed as direted by Engr-in-charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete.

S&F in repairs continous (piano hinges, mild steel bright finish or electro galvanized width of flap 30mm when open complete all as specified.

S&F in repairs 40mm dia cup board knob fixed with nut screw and washer of mild steel bright finish complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.

Taking down shutters of any description exceeding 1 square metre and not exceeding 2 square metre each complete , all as specified and directed by Engineer-in Charge.

M & L for 2nd class hardwood plain, solid, straight chowkats and frames wrougth, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

M & L for 35 mm thick factory made 2nd class hardwood plain, framed, panelled shutters (two panels), with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated and fixing to chowkat, complete all as specified.

M&L for 35 mm thick 2nd class hard wood glazed/gaused and skelton shutter, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified.

S&F fix factory made PVC Chowkat/ Door frame of size 50 x47mm with a wall thickness of 5mm ,made out of extruded 5mm thick single side prelam PVC sheet coloured reinforced with 19 x19 mm MS Square tube of 19 gauge including rubber gasket ,PVC fasteners, brackets complte all as specified and shown on drawing as per SSR 2010

S&F factory made solid PVC door shutter ,30mm thick (stiles) ,consisting of frame made of MS tubes for top and bottom rail,MS frame shall be covered with heat molulde plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stile and plain colour PVC sheet for top rail ,lockrail, bott rail and other side and as gap inserted for toprail and bottm rail, panelling of plain colour PVC sheet to be fitted on MS frame welded/sealed t the stiles and rails with suitable PVC sheet beading joined together with solvent cement .fixing the frame at site as per specification and drawing in SSR part-II complete all as specified.

S&F PVC 18mm thick PVC celluca ply one side prelam fixed with solvent cement adhesive and screws as in kitchen cabinate/cup board complete all as direction of the Enge-in-charge and the manufacturers specified and drawings (Make-Rajshri)

S&F for factory made PVC kitchen and cupboard frame of the size 75mm x40mm with a wall thickness of 4mm ,made out of extruded 4mm thick prelam PVC sheet reinforced with 15mm x15mm MS tube of 19 mm gauge thickness through out the fame and mitre cut at twp cprners and joined with 2Nos of 150mm loong brackets of 10mm x10mm MS tubes .the door frame shall be fixed to the wall using 65/100mm long MS screw through the frame by using PVC fastners, aluminiun of 4Nos if screws to be provided for each vertical member and for Horizantal members complete all as per manufactures specications and as directed (Make-Rahshri)

Supply and fix 200 mm long mild steel barrel tower bolt , complete all as specified

Supply and fix 300mm long, mild steel, sliding door bolt matt finish snot less than 16 mm dia bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts extruded section or cast aluminum alloy, complete all as specified.

Supply and fix extruded aluminum alloy handles fabricated type anodised of size 150mm long.

Supply and fix butt hinges, stailness steel 100 mm size welded to angle iron frames or fixed with screws to wooden frames.

Supply and fix 150mm mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding where ever necessary complete all as specified and directed Make:Ritz or equivelent

Supply and fix stainless steel wire cloth 0.38mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized iron staples including wooden beadings, complete all as specified and directed.

M&L 3mm thick sheet glass n exc 0.5 sqm each pane ordinary quality and glazing withoil putty or fixed with beads, all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), all as specified and directed by Engineer-in Charge.

S&F steel ventilator with top hung shutter including hinges ,steel peg stay complete half fixed galzed and half top hung flazed complete and directed ( glass shall be measured and paid separately)

Material and labour for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified

S & F in repair kitchen plate rack with four shelves made out of stainless steel sheet 1mm thick over all size 90x60x25cm complete all as specified

S&F in repair sink with drainage board made of stainless steel I mm thick kitchen or laboratory with plugs,washers and wastes coupling including bedding in cement mortar to dwarf wall, neccessary masonary work or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 405mm x 355mm x178mm . complete all as directed.

Taking up or down 15 mm dia steel water tubing and connections including all fittings, including cleaning for refixing or removall to store after cleaning.

Taking up or down 20 mm dia steel water tubing and connections including all fittings, including cleaning for refixing or removall to store after cleaning.

M & L 15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and ceiling or laid under floors etc complete all as specified.

M & L 20mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and ceiling or laid under floors etc complete all as specified.

Refixing 15 mm bore old steel water tubing medium grade galvanised and with all fittings, connections in new or old position (walls, ceiling, floor etc.) complete all as specified.

Refixing 20 mm bore old steel water tubing medium grade galvanised and with all fittings, connections in new or old position (walls, ceiling, floor etc.) complete all as specified.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall complete all as specified.

S & F in repair Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand and embeded in cement etc, complete all as specified.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), floor mounted with inbuilt P trap in white colour, including connection to trap and to flushing pipe including provn of cement concret beading complete all as specified and directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom end cover and mild steel chromium plated hanging device complete all as specified.

S&F in repair PVC valve less syphonic action type flushing cistern 10 ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all connection fixed, complete all as specified and directed.

S&F in repair Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, and fixed, complete all as specified and directed.

Supply and fix in repairs angle valve, fancy type, chromium plated brass, 15mm, complete all as directed.

S&F in repair PVC connection 15mm dia and 60 cms long with two nos of brass nuts and washers complete.

Supply and fix in repairs shower rose, chromium plated brass, fancy type, 100x100 mm, with or without swivel , any size, including fixing to steel pipe or union, complete all as directed.

Supply and fix in repairs 15 mm dia pillar taps, fancy type brass with capstan head chromium plated screwed down high pressure with or without lettered “hot/cold” with long screwed shank and flynut screwed complete all as specified

S&F stop valves cast copper alloy serwed down high pressure , 15 dia bore fixed in repairs.

S&F stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle 20mm dia bore fixed in repairs.

Demolition of stone slab and tiles of any description or thickness in floor apron etc complete all as specified and directed.

M&L for 18-20 mm Granite (any type) work (table rubbed and polished) in steps,jambs,pillars window-cill,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as spd.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

S & F glazed ceramic tiles in vertical surface,coloured, of size 600mm x 300mm x5 to 6mm thick onvertical surfaces such as dados,skirting etc., set and jointed with approved adhesive,including 10 mm thick rendering cement plaster in 1;4 CM and pointed in white cement with pigment to match all as specified .

M & L for coloured non skid ceramic tiles of size 300x300x 7-8mm as in floors, set and jointed in neat cement slurry as per manufacturers instructions and pointed in white/ coloured cement, laid over and including cement screed bed 15mm thick in cement mortar 1:6, complete all as specified.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed or bedding layers in cement mortar(1:6) complete all as specified and as directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed or bedding layers in cement mortar(1:6) complete all as specified and as directed.

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

S & F in repair Aluminium drapery Rod 25mm dia Powder Coated including wooden side caps, brackets, and rings @ 120mm c/c/ complete all as approved by Engineer-in-chareg

Dismantling and breaking up rain water pipes (CI,AC,PVC etc) set in any cement mortor of any diameter incl bends.

S&F PVC (SWR) pipes double socket in any length with rubber ring joints, fixed to walls 110mm mm dia ,in four storey building complete.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed.

PVC (SWR) bends any radius 110mm bore, complete all as specified.

S&F PVC (SWR) dia of bore 110 mm ,junction single ,(single T) equal or unequal dia of bore 110 mm,provide upto hieght of four storey building complete.

S&F stainless steel gratings 100mm bore size fixed with cement motar.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand blasting, scrubbing down concrete sufrace with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited all as specified and applying two layess of guniting over steel welded mesh 2mm dia of wire and aperture 75mm,total thickness of gunite n.exc 25mm thick (average thickness) in cement mortar 1: 2 using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturers instructions and finally applying cement plaster over gunited surface of required thickness to give even, uniform and smooth finish conforming to proper gerometrics in cement mortar ( 1 : 3) to match with the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias, parapets , columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 4 storey bldgs all as specified. (Note : Steel welded mesh is to be tightend / welded with the existing re-inforcement. The cost of welded mesh is deemed to be included in the unit rate quoted by the contractor).

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified.

M & L for preparation of horizontal/vertical surfaces of brick/concrete /existing roof treatment roof surfaces also removing the , cleaning and washing down and make the surfaces free from dust and other conteminate and providing "Coral waterseal-132 or equivalent of FOSROC water proofing treatment 3 to 5 mm thick layer, trowel finished incl 40mm thick pcc 1:2:4 type B0 complete all as per manufacturer instruction and directed (application of treatment shall be done through applicator of the manufacturer) complete all as specified and directed.

Demolition of reinforced cement concrete in any position (reinforcement cut as required to facilitate demolition) all as specified and as directed by Engineer -in-Charge.

M&L for precast cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in louvers and jallies 40mm thick designed as fort pattern (measured solid) including all moulding but exculding frame and set in CM1:4 all as per sample shown and directed by engineer-in -charge.

M&L aluminium alloy powder coated windows including aluminium coated frames silding track, bottom weighing not less than 1.015 kg/Rm ,sides and top not less than 0.826 kg/Rm double revated and 0.55 kg/Rm for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter silding type with aluminium sectins as per series-A (15mm) 3 track of jindal section number for silding windows with framed shutter including aluminium allow powder coated snap type beads handles with locking arrngement spring action and glazing clips joint cleats rubber gaskets etc inclding provision of 5.5 mm thick tinted glass/frosted glass of superior quality and stainless steel jail including all standard fittings complete all as specified and directed

M&L for preparation of old decorated plastered surfaces of walls, brooming down, washing with water etc and applying two coat of cement based paint over a coat of putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of putty complete all as specified as directed by Engr-in-charge.

Demolition Stone sett paving of any description or thickness complete all as specified as direted by Engr-in-charge.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and pigment, complete all as specified as direted by Engr-in-charge.

M&L 40 mm sand filling under interlocking paver block including watering and consolidation complete all as specified and directed.

100 mm thick plain cement concrete 1:4:8 type D-2(using 40 mm graded crushed stone aggregates) as in sub-floors, sub -base, floor and paving etc, finishing surface even and fair without using extra cement with complete all as specified and directed.

M&L Chequered cement concrete tiles 320x198.50x 30mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment, laid over and including 15mm thick screed bed in CM 1:6,complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Demolition of brick/stone masonry built in CM including all quoins, arches, pillars, etc bbut excluding ashlar facing, dressed stonework and precast concrete articles, complete all as specified.

M&L brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 all as specified.

M&L PCC 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in lintel up to 1.5m clear span, cill, steps, sismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, coping, etc incl necessary formwork, weathering, slightly rounded or chamfered angles and throating incl necessary form work complete all as specified and as directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in any type of soil, complete all as specified & directed.

Excavation in trenches exceeding 1.5m but not exceeding 3.0m depth and not exceeding 1.50m in width and getting out in any type of soil, complete all as specified & directed.

Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in soft/loose soil complete all as specified.

Removal of surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above starting point, complete all as specified.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 200mm dia complete including removal of debris from site and deposited in low lying area.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 150mm dia complete including removal of debris from site and deposited in low lying area.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm drain pipe after they are laid and tested in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 200mm drain pipe after they are laid and tested in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

M&L for 150 mm bore DWCPE drain pipes laid in trenches and jointed in CM 1:1 with spun yarn complete all as specified and directed.

M&L for 200mm bore DWCPE drain pipes laid in trenches and jointed in CM 1:1 with spun yarn complete all as specified and directed.

M&L PCC 1:4:8) type D-2 (using 40mm graded crushed stone aggregate), as in foundations, filling and mass concrete etc complete all as specified.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm dia pipes complete all as specified.

M&L Factory made Precast cement concrete manhole cover' area of each cover exceeding 0.20sqm but not exceeding 0.75 sqm 100 mm thichK Type B1 1:2:4 concreting including grove and hook arrangement for lifting and placing in position and side covered by MS Sheet complete all as specied and directed by E-IN-Charge

M&L Factory made Precast cement concrete manhole cover' area of each cover not exceeding 0.20 sqm 50 mm thick Type B1 1:2:4 concreting including grove and hook arrangement for lifting and placing in position and side covered by MS Sheet complete all as specied and directed by E-IN-Charge.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

TMT bars, 5mm dia and over upto incl 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups, complete all as specified.

M&L surface dressing clearing/uprooting of vegetation/tree/fancing along the alignment of boundary wall not exceeding 15 cm deep all as specified.

Form work to sides and sofits of floor or roof beam, beam hanuchings, girders, bressummers, lintels, contilever, shelves including supports, overhangs etc also splay between floors and beam, with rough finished surfaces of concrete complete all as specified & directed.

Form work to sides of concrete foundations, footings, basis of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better with rough finished surfaces of concrete complete all as specified & directed.

Form work to sides of pillars, posts, struts piers, columns and stanchions and similar works with rough finished surfaces of concrete complete all as specified & directed.

Taking down carefully copper / aluminium point wiring (light / fan socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing all as specified and directed.

Taking down main switch/ MCBs/ DBs any type and make all as directed by Engr-in-charge

Taking down Sub main wiring of any size and type from site making good to the disturbed surfaces all as specified and directed by Engr-in-charge.

Material and labour for point wiring for light/fan/ bell / buzzer/socket on independant board with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with using colour coding and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for Mylinc / Coral / Sleek model accessories etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per srl item No-110 here-in-before but one 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch.

All as per Serial Item No-110 above but point wiring with 4.0 Sqmm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 6 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

Supply and fixing modular switch, 06 Amps, single pole, one way, 230 volts, one module and IP 20 protection complete all as specified & directed.

Supply and fixing modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified & directed.

Supply and fixing modular socket outlet 02 in 01, 06 pin, 06 Amps and 16 Amps, 02 module with shutter complete all as specified & directed.

Supply and fixing modular switch, with indicator, 16 Amps, single pole, one way, 230 volts, one module and IP 20 protection complete all as specified & directed.

Supply and fixing ceiling fan regulator, 120W - 2 module, stepped type of 0 to 04 rotary steps, electronic, humfree, AC, 230 volts, duly ISI marked complete all as specified & directed.

Supply and fixing modular bell push with indicator, 06 Amps, single pole, one way, 230 volts, 01 module complete all as specified & directed.

Supply and fixing ding dong bell, AC, 230 volts, single pole complete all as specified & directed.

Supply and fixing ceiling rose, 6 Amps, 230 volts, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 65 x 50mm size complete all as specified & directed.

Supply and fixing lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting complete all as specified & directed.

Supply and fix LED bulb 14 watts, 1400 lumens output, 6500K suitable forB-22 base complete all as specified & directed.

Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 20-22 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Supply and fix LED batten luminaire surface mounted 2 feet system wattage of 9-10 watts and not less than 900 lm system lumen output with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, short circuit and over circuit protection, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Material & Labour Submain wiring using two single core PVC insulated cables with copper conductor(FRLS) of size 10 sq.mm (nominal area) & drawn into medium grade PVC conduit 25 mm dia with all fittings and accessories fixed concealed including chase cutting in brick/stone masonry walls for fixing conduit and plastering the external surface and matching the same with existing surface including provision of 10 sq.mm copper conductor (FRLS) PVC insulated earth wire complete all as specified. Note:- 2 Run of 10sqmm + 1 Run of 10 sqmm +1 Run of PVC conduit shall be measured as 1 RM.

Supply and Fixing Exaust fan metal body, AC 300 mm sweep, Air flow rate > 900cum/min, Bird screen for protection against birds, double ball bearing, 1400 RPM, metal body with louvre single phase including with louvers and provision of cable from cealing rose to fan, complete all as specified and directed.

Supply & Fixing sheet metal enclosures factory made, (Double door) for DBs, single pole and neutral, 240 volts, 12 ways with 200 Amp rated busbar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, testing and commissioning, complete all as specified and directed.

Supply & Fixing sheet metal enclosures factory made, (Double door) for DBs, single pole and neutral, 240 volts, 08 ways with 200 Amp rated busbar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, testing and commissioning, complete all as specified and directed.

Supply and fixing in repair MCB, SPN, AC, 240 volts of 63 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fixing in repair MCB, SP, AC, 240 volts of 10 to 32 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried vertically in ground (earth pit not less than 2.25meter deep below ground level) with top edge of the plate not less than 1.5meter below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 5 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 75mm center to center both way with 12mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40mmx40mmx3mm frame for pit cover including testing on completion complete all as specified and directed.

S&F MCCB enclosure box suitable for mounting 125 Amp FP, MCCB and mounted on wall or as per site requirement including fitting accessories complete all as specified and directed by engineer in charge. Make:- Legrand, Schneider or Indoasian.

Supply and fix MCCB 125 Amps, four pole 415 volts 16 KA 50 HZ with thermal magnetic setting and Adjustable, complete all as specified and directed by engineer in charge.

M&L for breaking old existing wall and making a provn for fixing of 300 mm sweep exhaust fan/250 mm fresh air fan including making good to the disturbed wall/ portion and matching with existing colour.all as specified and directed.

S&f fresh air fan PVC body AC single phase 230/240 V of size 250 mm sweep,body air delivery > 800 CMH , 5 number of blades, AC with louvre fixed complete with suitable size ply by cutting into suitable size as required complete all as specified and directed by Engr-in-Charge.

Supply and fixing ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220 cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as directed.

Supply and Fix 45 W High efficient LED Street light fitting with pressure die cast LM6 Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie is 100lm/W with a life class of 50,000 burning hours at L70.The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected with IK05 impact resistance. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<20%, High and low protection along with a surge protection of 4 KV including provision of 40mm dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on pole fixed complete as specified and directed.

S & F water heater storage type Geyser vertical type with suitable size of fastner and, inner tank material of superior glass line tank and outer body material of ABS with high pressure with standing enabling (up to 8 bar pressure) capacity including provision and connecting up of SS braidedpipe with adopter for inlet and outlet water connection having adjustable knob for temperature control and inner tank should be glass line coated, capacity 25 Ltrs, having heating element 1.5 KW and not less than 5 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed .

M&L for cutting steel tubing to required length for insertion of new Tee Branches, reducer in any position of 15mm dia pipe line complete all as specified and directed.

S&F of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of cap 15mm dia complete all as directed

S&F in Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, and fixed, complete all as specified and directed.

S&F PVC connection 15 mm size for cold water with PTMT nuts of length 450 mm complete all as specified and directed.

S&F CP connection 15 mm size with for hot water with PTMT nuts of length 450 mm.complete all as specified and directed.

S&F stop valves 15 mm bore CP With crutch or butterfly handle, screwed both ends for iron pipe or unions, complete all as directed.

Supply & fix in repair factory made epoxy powder coated Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB 125/160 Amp as incomer and 40 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623.

Supply and Fix single phase 10-60 amps, 230 volts, 50 Hz electric energy meter with LCD display with optical port, base mounting accuracy class 1.0 having provision of manual/automatic meter reading display capability complete all as specified and directed by Engr-in-charge.

Supply & fixing industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volts of 20 Amps, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply & fixing industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volts of 10 Amps, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix 18 watts LED bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 90 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specified and directed.

S & F Decorative wall mounting Light fixture made up of Polycarbonate with B-22 base, suitable for LED 14 w bulb fixed complete all as directed.

Supply and laying including connecting and testing of LT under ground electric cable of size 25 sqmm 04 core XLPE insulated and PVC sheathed armoured heavy duty multi stranded 1100 Volts grade with aluminium conductor, laid in trenches or drawn through existing pipe or fixed to wall with providing suitable size of aluminium lugs, GI nuts bolts and washers complete wherever required all complete all as specified and as directed .

Supply and laying including connecting and testing of LT under ground electric cable of size 06 sqmm 2 core XLPE insulated and PVC sheathed armoured heavy duty multi stranded 1100 Volts grade with aluminium conductor, laid in trenches or drawn through existing pipe or fixed to wall with providing suitable size of aluminium lugs, GI nuts bolts and washers complete wherever required all complete all as specified and as directed .

Supply and fix GI Pipe 32 mm dia light grade, for laying in road crossing/ fixing of vertically complete all as directed

Sand cushioning to protection of underground cables, laid 8cm before laying and 15cm after laying of cable and punned to form an overall layer of 18cm thick complete all as specified and directed by the Engr-in-Charge. Note: Punned down thickness shall be considered for measurement.

Material and labour for kiln burnt Sub class 'B' bricks laid dry , flat , width wise along the length of cable in trenches after sand cushioning for protection of under ground cable complete all as specified and directed.

M &L telephone Point wiring complete with single pin 0.61mm dia copper conductor cable telephone pain taped and rip conforming to ITD specification D-3003 and ITI-113C/114C cable PVC insulated drawn though PVC concealed conduit not less than 20 mm dia for one 2 pin telephone socket out let on independent modular type board complete all as specified and as directed.

Supply & Fix in repair RJ-11 Telephone socket with transparent shutter 1 module on phenolic laminated sheet etc as required complete all as specified and as directed.

S&F LED Post top lanterns 40Watt made in cast valuminium spigot housing with decorative clear opal acrylic diffuser and IP 65 protection incl necessary PCC work for grouting of base pipe and making electrical connections complete all as directed by Engr-in-Charge.

Material & Labour submain wiring using two single core PVC insulated cables with copper conductor(FRLS) of size 04 sq.mm (nominal area) & drawn into medium grade PVC conduit 25 mm dia with all fittings and accessories fixed concealed including chase cutting in brick/stone masonry walls for fixing conduit and plastering the external surface and matching the same with existing surface including provision of 4 sqmm copper conductor(FRLS) PVC insulated earth wire complete all as specified. Note:- 2 Run of 04sqmm + 1 Run of 4 sqmm +1Run of PVC conduit shall be measured as 1 RM.

Mateial & Labour submain wiring using two single core PVC insulated cables with copper conductor(FRLS) of size 06 sq.mm (nominal area) & drawn into medium grade PVC conduit 25 mm dia with all fittings and accessories fixed concealed including chase cutting in brick/stone masonry walls for fixing conduit and plastering the external surface and matching the same with existing surface including provision of 06 sq.mm copper conductor(FRLS) PVC insulated earth wire complete all as specified. Note:- 2 Run of 06sqmm + 1 Run of 06 sqmm +1Run of PVC conduit shall be measured as 1 RM.

S&f Wall mounted fans AC single phase 230/240 V, of size 400 mm sweep, speed RPM 1400,Sturdy and shock proof body for fixing of wall fan complete.

SHREE RAM BUILD TECH

Shiv Shankar Nirman Co.

The new hut furnitures

SHEELSONS ENTERPRISES

n s kumar and sons

garnet engineers contractors

LAMBA ENTERPRISES