PROVN OF RECEPTION, SECURITY STAFF ROOM, FFL AND SPECIAL REPAIR TO CERTAIN BUILDINGS AT DIFFERENT LOCATIONS OF BAGRAKOTE MIL STN

Amount

Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed.

Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, complete all as specified and directed.

Taking down CI soil, waste,vent or rain water pipe, 100mm dia (any pattern) including all fittings head shoes etc complete all as specified and as directed.

Demolition of brickwork built in cement mortar and removing rubbish off the premises etc complete all as specified and directed

Dismantling timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed

Taking up or down 15 mm bore steel water tubing and connections complete all as specified.

Taking up or down 20 mm bore steel water tubing and connections complete all as specified.

Dismantling PVC/HDPE/plastic water tank of capacity Exc 500 Litre and not Exceeding 1000 Ltr complete all as specified and directed

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

All as per Item No.15 above but in hard/dense soil.

Excavating in trenches not exc 1.5m wide and exc 1.5 m but n.exc 3 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

All as per Item No.17 above but in hard/dense soil.

Excavation over areas not exc 1.5 m in deep and getting out in hard/dense soil complete all as specified and directed.

Excavation over areas exc 1.5 m but not exc 3 m in deep and getting out in hard/dense soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Materials and Labour for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed.

Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface.

Materials and Labour for plain cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:2:4) type B-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:2:4) type B-0, using 12.5mm graded stone aggregate as in coping, kerbs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-1, using 20mm graded stone aggregate as in holdfast block, filling of MS chowkats and the like including necessary formwork complete all as specified and as directed.

Materials and Labour for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and as directed.

Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, cantilevers, lintels, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

Materials and Labour for formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similer works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slabs and shelves supported on walls, beams and columns in floors, roofs and landings etc, any thickness complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for 6 to 8 mm dia round bars as in reinforcement for half brick thick walls, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250) quality-A/Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation of surface) at workshop before fabrication complete all as specified and as directed.

Supply & fixing Mild steel screw bolt (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be filled with washers and one hexagonal or square nut 5 to 10mm dia shank and exc 5cm but n exc 10cm long complete all as specified and as directed.

Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply & fixing rolled mild steel Flats , channel, angle or tee sections as in wind ties for roof including securing bolts, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply & fixing Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

Materials and labour for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Materials and labour for preparing of newly primed steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , below 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 20mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for coloured 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 M-35 grade, laid as directed to any shape. Complete all as specified and as directed

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in plinth protection, path etc. finished the surface of concrete even and smooth without using extra cement complete all as specified and directed.

Materials and labour for 25 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggt as in sub bases of floor finished even and rough, complete all as specified and directed.

Materials and labour for 50 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggt as in sub bases of floor finished even and rough, complete all as specified and directed.

Materials and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete fair and even, complete all as specified and directed.

Materials and labour for 40mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in DPC, WPC shall be mixed with concrete as directed, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only).

Materials and labour for brick work with fly ash bricks modular size straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

Materials and labour for brick work with fly ash bricks modular size, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:4 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in one and half brick thick honey comb walls built in cement mortar 1:4 complete all as specified and as directed.

Materials and labour for broken brick bats to fill in soakage well complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

Supply and fixing 165 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified.

Supply and fixing 35mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed.

Supply and fixing 35 mm thick second class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed.

Supply and fixing mild steel stove enamelled black 300mm long ordinary rat tail rod pattern spring fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed.

Supply and fixing stainless steel butt hinges, 100 mm size , complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 100 mm size , complete all as specified and directed.

Supply and fixing Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200 mm , complete all as specified and directed.

Supply and fixing Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 300 mm , complete all as specified and directed.

Supply and fixing Mild steel pressed handles, oval type, stove enamelled black, 150 mm size, complete all as specified and directed.

Supply and fixing stainless steel curtain rod 20 mm dia complete al as specified and directed.

Supply and fixing stainless steel brackets for holding curtain rod of 20 mm dia, fancy type complete al as specified and directed.

Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete without glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing steel ventilators with top hung shutter including hinges,steel peg stay, including one shop coat of Zinc Chrome primer complete all as specified and directed.

Supply and fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement mortar (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only liquid Water Proofing Compound of approved make.

Materials and labour for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces and applying two coats of cement based paint over a coat of alkali resistant primer on wall complete all specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over chalk whitening after preparation of surface complete all as specified and directed.

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 2.5 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling and applying three coats of white wash including preparation of surface complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher)

Supply, laying, jointing & testing 3-layer PP-R (Polypropylene random copolymer) concealed pipes, 32 mm outer dia, SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings such as bends, elbow. tee, socket, reducers, unions fixed complete to walls, ceilings, trenches or in floors etc as required at site complete all as specified and directed.

Supply and fixing PP-R Gate valves (brass insert), for 32 mm outer dia pipe, as per requirement of the site including taking down unserviceable valves complete all as specified and as directed of the following sizes:-

Supply and fixing 15 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing 20 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing Vitreous China wash down water closet pan (pedestal pattern), white with "P" or "S" Trap front or back inlet fixing bolts, PVC seat cover complete and making all necessary connection as specified and directed.

Supply and fixing Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) incl setting the trap and pan in cement mortar (1:3:6) all round and "P" or "S" Trap, complete all as specified and directed.

Supply and fixing 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply and fixing Vitreous China wash hand basin, white, flat back, size 550x400mm, including 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, brackets, with and incl 32mm dia 90cm long PVC waste down pipe, includind S&F cromium plated Pillar taps 15 mm bore, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

All as per Item No.101 above but fixing in repairs including taking down old unserviceable complete .

Supply and fixing for 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

Supply and fixing 15mm cromium plated Bib taps, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

All as per Item No.104 above but fixing in repairs including taking down old unserviceable complete .

Supply and fixing 15 mm bore angular stop valve cast copper alloy fancy type chromium plated with long shank and cup with capstan head wall flange etc screwed down screwed for iron pipe complete all as specified and directed. .

Supply and fixing in repair Concealed 15 mm bore stop valve cast copper alloy fancy type chromium plated with long shank and cup (concealed type) with capstan head wall flange etc screwed down screwed for iron pipe complete all as specified and directed. .

Supply and fixing 15mm bore dia two way bib taps cast copper alloy chromium plated, fancy type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and as directed.

Supply and fixing CP Soap dish holder including CP screws complete all as specified and as directed.

Supply and fixing CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

Supply and fixing 150mm dia DWC PE pipes (SN-8), ISI marked, in any length jointed and laid in trenches or in floors, complete all as specified and directed.

Materials and labour for concrete bed to 100/110 mm dia drain pipes using PCC (1:3:6) type C2, using 40 mm graded crushed stone aggregate, including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 75mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore complete all as specified and directed.

Supply and fixing PVC (SWR) vent cowl 75mm bore, complete all as specified and directed.

Supply and laying Salt-glazed stoneware (SWG) drain pipes, 150mm dia, laid in trenches and jointed as specified complete all as specified and directed.

Supply and laying Salt-glazed stoneware (SWG) drain pipes, 100mm dia, laid in trenches and jointed as specified complete all as specified and directed.

Supply and fixing PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fixing PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

Supply and fixing in repairs brass chromium plated, shower rose, 125mm size complete all as specified and directed.

Supply and fixing 32mm bore low density polyethylene pipes (LDPE) of pressure rating 6 Kgf / cm2, fixed to walls, ceiling or laid in floors etc complete all as specified and directed.

Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply & fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity hoisted and fixed in position, connecting with existing pipes all as specified in SSR Part I complete all as specified and directed.

Supply and fixing ball brass valves of size 20 mm bore high pressure, with polythene float and fly nut, screwed for iron pipe etc complete all as specified and directed.

Supply and fixing ball brass valves of size 25 mm bore high pressure, with polythene float and fly nut, screwed for iron pipe etc complete all as specified and directed.

Supply and fixing in repair 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

All as per Item No.131 above but fixing in repairs including taking down old unserviceable Gun metal gate or globe valve .

Supply and fixing 25 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Supply and fixing Modular Septic Tank of Capacity 9500 Ltrs (30-50 Users) (plastic septic tank) with inlet/outlet sizes of 160mm, 2 domed ends coupled type includng all accessoried and lowering into position and fixed to inlet and outlet pipes complete all as per manufacturer instructions and directed by Engineer-in-Charge. Make:- Supreme/ Sintex Plastics/ Aqua tech.

Supply and fixing Modular Septic Tank of Capacity 2000 Ltrs (9-10 Users) (plastic septic tank) with inlet/outlet sizes of 160mm, stand alone type includng all accessoried and lowering into position and fixed to inlet and outlet pipes complete all as per manufacturer instructions and directed by Engineer-in-Charge. Make:- Supreme/ Sintex Plastics/ Aqua tech.

Supply and fixing Cast Iron work as in CI manhole covers, 600 mm dia, grade FG 150, and similar articles exceeding 5 Kg each, complete all as specified and as directed.

Materials and labour for cutting and screwing existing 50 mm dia steel tubing for alterations or additions (or lengthening screw on pipe to form connector) as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Materials and labour for concealed point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete. NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates. all as specified and directed.One light/fan/call bell point controlled by one switch one way 5 Amps

All as per Item No.139 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.139 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

Supply and fixing Switch piano, flush type, single pole, one way switch 5 Amps.

Supply and fixing Switch socket combination 2 in 1, 5 Amps flush type.

Supply and fixing Switch socket combination multipurpose 5 A/16 Amps,5 in 1, flush type.

Supply and fixing Ceiling rose surface bakelite 3 terminals 65x50mm all as directed.

Supply and fixing electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and directed.

Supply and fixing Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing LED Lamp, 9 Watt B22 complete all as specified and directed.

Supply and fixing in repair energy saving and environmental friendly long life LED security/street Light fittings 35 watts, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover, IP 66 protection, inbuilt driver, connecting with suitable size copper wire, with 32mm bore 1 m long medium grade GI bracket made to shape complete all as specified and as directed.

Supply, fixing and connecting exhaust fan made of polycarbonate/sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed.

Supply and fixing decorative box type surface and wall mounted 18/20 Watt LED light fittings, 6500 K, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply and fixing decorative box type surface and wall mounted 9/10 Watt LED light fittings, 6500 K, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply and fixing in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fixing MCB distrubution board SPN 8way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB distrubution board SPN 4way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB Single pole, 240 volts 5 to 32 Amps 10 KA rupturing capacity, C series

Supply and fixing MCB Single pole & neutral, 240 volts 32 Amps 10 KA rupturing capacity, C series

Supply and laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 16 Sqmm 2 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed including taking down old unserviceable XLPE cable with brick protection and complete all as specified and as directed.

All as per Item No.159 above but size of XLPE cables 10 Sqmm 2 Core.

All as per Item No.159 above but size of XLPE cables 6 Sqmm 2 Core.

Materials and labour for GI pipe light grade with all fittings complete grouted in ground all as specified for 40 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable complete all as specified and directed.

Materials and labour for GI pipe light grade with all fittings complete grouted in ground all as specified for 25 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable complete all as specified and directed.

Supply & laying 50 mm outside dia double wall corrugated pipe(DWCPE) for enclosing cable below ground/road surface to a required depth including suitable size couplers for jointing of pipe all as per site requirement etc complete all as specified and directed.

Materials and labour for boring holes 1mtr deep in soil under roads/PCC as directed for cable passing through pipes of required size and disposal of soil to a distance not exc. 50m. (Note: Connected items like Pipes is measured and paid seperately under relevant items).

Materials and labour for earthing complete with galvanized steel pipe electrode 40mm bore , medium grade, 2.5 meters length, buried directly and preferably vertically in ground with top edge not less than 1.25 meters below ground level connected with earthing lead galvanized iron strip of size 25x5 mm connected to galvanized earth pipe by means of bolts, nuts, checknuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 6mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fix with cast iron funnel and wire-mesh , with protection pipe of 32 mm dia light grade galvanized steel tubing upto 7.5 meters length for drawing earthlead including common salt, charcol , bentonite in alternate layers etc, complete all as shown in EP number 2 of SSR part-1 including testing on completion and including taking down old u/s earthing & testing complete all as specified and as directed.

M S ALOK SAHA

NARESH GUPTA

M S BHARAT CONSTRUCTION CO.

ANJALI CONSTRUCTION

AJOY DEY

B K SINGH

RAJU AICH