Improvement of power supply distribution network in Central Gotanagar colony, replacement of overhead lines with underground cables.

of overhead lines with underground cables.

Item- 1 Part A: Central Gotanagar North Side

S No. Item Description of Item Unit Qty Rate Amount

NFR HQ-ELECTRICAL/N F RLY

1 1 Design, supply , installation , testing and Set 2.00 374156.00 748312.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 630 Amps comprising with the followings:-

A. 01 Nos. 630 Amps 4P on-load Change over switch

with proper connection to the panel., B. 02 Nos. 400

Amps , 4 pole, 36 KA microprocessor released based

MCCB suitable for mounting in the above LT panel

board, providing with necessary connection with

thepanel, C. 06 Nos. 200Amps 4P 36 KA

microprocessor released based MCCB suitable for

mounting in the above LT panel board, providing

with necessary connection with the panel, including

internal connection should be stranded copper strips

of suitable size from the bus bar to be provided as

per direction at site Engineer. The design of LV

Panel shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

NFR HQ-ELECTRICAL/N F RLY

2 2 Design, supply , installation , testing and Set 4.00 195478.00 781912.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 400 Amps comprising with the followings:-

A. 02 Nos. 200 Amps 4 pole, 36 KA microprocessor

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with thepanel, B. 06 Nos. 125 Amps , 4

pole, 25 KA adjustable thermal and magnetic

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

NFR HQ-ELECTRICAL/N F RLY

3 3 Design, supply , installation , testing and Set 7.00 167219.00 1170533.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 200 Amps 4 pole, 36 KA microprocessor

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with the panel, B. 20 Nos. 63 Amps , 4

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

4 4 Carrying, Laying, commissioning of various size Metre 6700.00 32.00 214400.00

Aluminium armoured LT cable partly along the pole

and partly through ground in cable trench with

suitable fixing arrangement. Loading, unloading &

carrying of cable to actual work site by contractor

own arrangement as per instruction of Engineer in-

charge at site. (Cable will be supplied by Railway)

5 5 Excavation for cable trenches in soft soil, depth upto Metre 600.00 622.00 373200.00

1.2 m including dressing of sides lift upto 1.5 m,

including getting out the excavated soil, refilling

with sand and or good soil after laying of cable/ pipe

etc in layers of 20 cm, ramming, watering and

disposal of surplus excavated soil as directed, within

a lead of 50 metres . As DSOR Item No. 14.4

6 6 Supply, installation, testing & commissioning of 40A Numbers 70.00 5055.00 353850.00

4P MCB, B/C SERIES with thermoplastic enclosure as

per direction of site engineer in-charge.

7 7 Supply, Carrying, laying, fitting, fixing & Metre 500.00 111.00 55500.00

commissioning of 63(OD) mm diameter Double wall

corrugated PN-6.0 Kgf/cm2 HDPE Pipe partly through

over ground , partly through underground with ISI

marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II

complete with fitting and cutting, jointing etc. as per

direction of site engineer in charge of Railway.

8 8 Supply, installation, testing, and commissioning of Set 6.00 47256.00 283536.00

an indoor busbar panel equipped with a 200A

busbar, comprising 4 nos of 40A, 4-pole, B/C-curve

MCBs, along with dedicated space and provisions for

the installation of 4 Nos of energy meters.

9 9 Dismantling of existing overhead LT lines with all Each 50.00 556.00 27800.00

accessories without damage from the work site and Span

handing over to concerned SSE office as per

instruction of site Engineer in-charge of railway.

NFR HQ-ELECTRICAL/N F RLY

10 10 Supply, erection of earthing set by 80 mm Dia GI Numbers 80.00 3323.00 265840.00

pipe 4 Mts. long including construction of earth pit

with cover and earth continuity by (25x3)mm GI

strip , GI nuts and bolts etc. as per direction at site

11 11 Supply & erection of GI tubular pole 9.5 Meter long Numbers 10.00 14139.00 141390.00

type410, SP -32 with suitable size step length,

section diameter and sectional thickness as per IS

2713 of 1980 including suitable size of base plate

and cap on top and digging of pit to 1/5th of the pole

height and supply and construction of CC foundation

in ratio 1:2:4 by cement, Sand and Ships of size 19

mm. The CC block will be 30 cm x 30 cm from

bottom of the pole up to 30cm above the GL.

12 12 Supply, fitting, fixing and testing of outdoor type 60 Numbers 60.00 3165.00 189900.00

watts LED street light fitting complete with LED

lamp, bend pipe and all other accessories including

connecting cable and provision of necessary hanging

arrangement etc. as per site requirement. Lumens

output should be greater than 100 Lumens/watt,

LED driver's efficiency should be minimum

90%,Power factor of complete fitting should be

greater than 0.90, Input operating voltage: 140V to

13 13 Excavation of horizontal boring manually for outside Metre 120.00 766.00 91920.00

of the Road/Railway track Embankment at a

minimum distance of 6 meters. From the

embankment GL and depth of 2.0 meters. Below

from G.L. with preparation of site for boring by

placing of pipes for electric cable protection through

contractor own arrangement as per direction of site

14 14 Supply, installation, and laying of G.I. pipe (medium Metre 50.00 2321.00 116050.00

class) of 150 mm (ID) with all necessary accessories

as per requirement at site.

15 15 Supply, installation, and laying of G.I. pipe (medium Metre 50.00 1488.00 74400.00

class) of 100 mm (ID) with all necessary accessories

as per requirement at site.

16 16 Supply, installation, and laying of G.I. pipe (medium Metre 70.00 635.00 44450.00

class) of 50 mm (ID) with all necessary accessories

as per requirement at site.

17 17 Supply, installation, testing and commissioning of Set 55.00 2979.00 163845.00

MS Junction box with 6 A MCB for street light pole

connection with all connecting accessories as per

requirement and direction of site engineer in-

NFR HQ-ELECTRICAL/N F RLY

18 18 Design, supply , installation , testing and Set 2.00 79941.00 159882.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 125 Amps 4 pole, thermal magnetic

based 25KA 4 pole MCCB,suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, B. 4 Nos 40 Amps , 2

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

19 19 Supply and wiring of sub- main line concealed by RM 2000.00 180.00 360000.00

2x10 sq. mm. PVC insulated unsheathed and multi

stranded FRLS Copper Cable confirming to IS

694/1990 through suitable size of PVC conduit pipe

with 1sq. mm unsheathed copper cable as earth

continuity wire.

20 20 Supply, installation, testing and commissioning of a Numbers 46.00 242.00 11132.00

cable route marker consisting of a 10 cm x 10 cm x

5 mm thick galvanized iron (G.I.) plate with custom

inscription, securely bolted or welded to a 35 mm x

35 mm x 6 mm angle iron post (60 cm long),

including excavation and fixing the assembly firmly

in the ground as required.

Item- 2 Part B: Central Gotanagar South Side

S No. Item Description of Item Unit Qty Rate Amount

NFR HQ-ELECTRICAL/N F RLY

1 1 Design, supply , installation , testing and Set 2.00 374156.00 748312.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 630 Amps comprising with the followings:-

A. 01 Nos. 630 Amps 4P on-load Change over switch

with proper connection to the panel., B. 02 Nos. 400

Amps , 4 pole, 36 KA microprocessor released based

MCCB suitable for mounting in the above LT panel

board, providing with necessary connection with

thepanel, C. 06 Nos. 200Amps 4P 36 KA

microprocessor released based MCCB suitable for

mounting in the above LT panel board, providing

with necessary connection with the panel, including

internal connection should be stranded copper strips

of suitable size from the bus bar to be provided as

per direction at site Engineer. The design of LV

Panel shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

NFR HQ-ELECTRICAL/N F RLY

2 2 Design, supply , installation , testing and Set 3.00 195478.00 586434.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 400 Amps comprising with the followings:-

A. 02 Nos. 200 Amps 4 pole, 36 KA microprocessor

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with thepanel, B. 06 Nos. 125 Amps , 4

pole, 25 KA adjustable thermal and magnetic

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

NFR HQ-ELECTRICAL/N F RLY

3 3 Design, supply , installation , testing and Set 7.00 167219.00 1170533.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 200 Amps 4 pole, 36 KA microprocessor

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with the panel, B. 20 Nos. 63 Amps , 4

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

4 4 Carrying, Laying, commissioning of various size Metre 6700.00 32.00 214400.00

Aluminium armoured LT cable partly along the pole

and partly through ground in cable trench with

suitable fixing arrangement. Loading, unloading &

carrying of cable to actual work site by contractor

own arrangement as per instruction of Engineer in-

charge at site. (Cable will be supplied by Railway)

5 5 Excavation for cable trenches in soft soil, depth upto Metre 600.00 622.00 373200.00

1.2 m including dressing of sides lift upto 1.5 m,

including getting out the excavated soil, refilling

with sand and or good soil after laying of cable/ pipe

etc in layers of 20 cm, ramming, watering and

disposal of surplus excavated soil as directed, within

a lead of 50 metres . As DSOR Item No. 14.4

6 6 Supply, installation, testing & commissioning of 40A Numbers 70.00 5055.00 353850.00

4P MCB, B/C SERIES with thermoplastic enclosure as

per direction of site engineer in-charge.

7 7 Supply, Carrying, laying, fitting, fixing & Metre 500.00 111.00 55500.00

commissioning of 63(OD) mm diameter Double wall

corrugated PN-6.0 Kgf/cm2 HDPE Pipe partly through

over ground , partly through underground with ISI

marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II

complete with fitting and cutting, jointing etc. as per

direction of site engineer in charge of Railway.

8 8 Supply, installation, testing, and commissioning of Set 4.00 47256.00 189024.00

an indoor busbar panel equipped with a 200A

busbar, comprising 4 nos of 40A, 4-pole, B/C-curve

MCBs, along with dedicated space and provisions for

the installation of 4 Nos of energy meters.

9 9 Dismantling of existing overhead LT lines with all Each 30.00 556.00 16680.00

accessories without damage from the work site and Span

handing over to concerned SSE office as per

instruction of site Engineer in-charge of railway.

NFR HQ-ELECTRICAL/N F RLY

10 10 Supply, erection of earthing set by 80 mm Dia GI Numbers 80.00 3323.00 265840.00

pipe 4 Mts. long including construction of earth pit

with cover and earth continuity by (25x3)mm GI

strip , GI nuts and bolts etc. as per direction at site

11 11 Supply & erection of GI tubular pole 9.5 Meter long Numbers 10.00 14139.00 141390.00

type410, SP -32 with suitable size step length,

section diameter and sectional thickness as per IS

2713 of 1980 including suitable size of base plate

and cap on top and digging of pit to 1/5th of the pole

height and supply and construction of CC foundation

in ratio 1:2:4 by cement, Sand and Ships of size 19

mm. The CC block will be 30 cm x 30 cm from

bottom of the pole up to 30cm above the GL.

12 12 Supply, fitting, fixing and testing of outdoor type 60 Numbers 60.00 3165.00 189900.00

watts LED street light fitting complete with LED

lamp, bend pipe and all other accessories including

connecting cable and provision of necessary hanging

arrangement etc. as per site requirement. Lumens

output should be greater than 100 Lumens/watt,

LED driver's efficiency should be minimum

90%,Power factor of complete fitting should be

greater than 0.90, Input operating voltage: 140V to

13 13 Excavation of horizontal boring manually for outside Metre 130.00 766.00 99580.00

of the Road/Railway track Embankment at a

minimum distance of 6 meters. From the

embankment GL and depth of 2.0 meters. Below

from G.L. with preparation of site for boring by

placing of pipes for electric cable protection through

contractor own arrangement as per direction of site

14 14 Supply, installation, and laying of G.I. pipe (medium Metre 60.00 2321.00 139260.00

class) of 150 mm (ID) with all necessary accessories

as per requirement at site.

15 15 Supply, installation, and laying of G.I. pipe (medium Metre 60.00 1488.00 89280.00

class) of 100 mm (ID) with all necessary accessories

as per requirement at site.

16 16 Supply, installation, and laying of G.I. pipe (medium Metre 80.00 635.00 50800.00

class) of 50 mm (ID) with all necessary accessories

as per requirement at site.

17 17 Supply, installation, testing and commissioning of Set 40.00 2979.00 119160.00

MS Junction box with 6 A MCB for street light pole

connection with all connecting accessories as per

requirement and direction of site engineer in-

NFR HQ-ELECTRICAL/N F RLY

18 18 Design, supply , installation , testing and Set 2.00 79941.00 159882.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 125 Amps 4 pole, thermal magnetic

based 25KA 4 pole MCCB,suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, B. 4 Nos 40 Amps , 2

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

19 19 Supply and wiring of sub- main line concealed by RM 1950.00 180.00 351000.00

2x10 sq. mm. PVC insulated unsheathed and multi

stranded FRLS Copper Cable confirming to IS

694/1990 through suitable size of PVC conduit pipe

with 1sq. mm unsheathed copper cable as earth

continuity wire.

20 20 Supply, installation, testing and commissioning of a Numbers 40.00 242.00 9680.00

cable route marker consisting of a 10 cm x 10 cm x

5 mm thick galvanized iron (G.I.) plate with custom

inscription, securely bolted or welded to a 35 mm x

35 mm x 6 mm angle iron post (60 cm long),

including excavation and fixing the assembly firmly

in the ground as required.

Item- 3 Part C: Central Gotanagar East Side

S No. Item Description of Item Unit Qty Rate Amount

NFR HQ-ELECTRICAL/N F RLY

1 1 Design, supply , installation , testing and Set 1.00 1032413.00 1032413.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

corrosion proof, chemically treated , colour of panel

shall be RAL 7035 structured finish , modular in

construction made of suitable size, using CRCA

Sheet Steel of 2mm thickness and are Epoxy powder

coating having 9 tank process having provision of

cable alley in both sides with 1 set 3 phase with

neutral (TPN) electrolytic grade 800A COPPER bus

bar and bus bar system shall have heat shrinkable

coloured PVC sleeve having 1. a) Supply & erection

of 1no. 4 pole microprocessor based manually

operated draw out (MDO) type 800A Air Circuit

Breaker with breaking capacity (Icu = Ics = Icw for 1

sec = 50KA) mechanical life = 20000 cycles,

Electrical life =20000 cycles, intrinsic degree of

protection of IP54 rating plug conforming to IS:

60947-II/IEC: 60947-II, operating voltage up to 690V,

Impulse withstand capacity =12KV. The ACB shall be

suitable for continuous operation at Ambient

Temperature of 50 degree Centigrade without any

duration. 4 pole ACBs should have 100% neutral

rating. The ACB should be fitted with proper wiring

in panel.ACB will have inbuilt - 2 NO+ 2 NC Aux.

contact, safety shutter assembly, racking handle,

door sealing frame, push-button cover & rating error

preventor. The ACB should conform the following

technical specification :- Rated current at 50°C:

1600 Ampere Type of Release: Microprocessor

based Rated operational voltage (V), 50/60Hz: 415

Volt Rated insulation voltage (V), 50/60Hz: 1000 Volt

Number of Poles: 4 Rated service short circuit

breaking capacity 50/60Hz (kA RMS): 50 KA Rated

impulse withstand voltage of main circuit (kV): 12

KV Typical opening time and closing time (ms): 40

ms and1 Typical opening time and closing time

(ms): 40 ms and 60 ms respectively. Electrical &

Mechanical life (operating cycles): 20000

Icu=Ics=Icw for 1 Second with Combined Test

Sequence Certification. Typical opening time and

closing time (ms): 40 ms and 60 ms respectively.

Electrical & Mechanical life (operating cycles): 20000

Icu=Ics=Icw for 1 Second with Combined Test

Sequence Certification. A) Supply, fitting, fixing,

testing & Commissioning of 01 No. 630A 4pole

microprocessor based 36 KA MCCB B)Supply, fitting,

fixing, testing & Commissioning of 12 Nos. 250Amp

4Pole 35ka Adjustable Thermal magnetic released

MCCB suitable for mounted in the above LT panel

board, connection of outgoing supply of copper bar

of suitable size from the bus bar as per instruction of

site Engineer. C)Supply, fitting, fixing, testing &

commissioning of 02 no Astronomical timer with 100

Amps 4 pole power contactor suitable for mounting

in the above LT panel board. Specification of Panel

as per Annexure-P(LV panel) of attached tender

document. (Breaking capacity of all MCCB's should

be Ics=100% Icu with adjustable magnetic settings

and MCCB's shall have a rated service voltage up to

690V and rated impulse withstand voltage shall not

be lesser than 8 KV)

NFR HQ-ELECTRICAL/N F RLY

2 2 Design, supply , installation , testing and Set 2.00 374156.00 748312.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 630 Amps comprising with the followings:-

A. 01 Nos. 630 Amps 4P on-load Change over switch

with proper connection to the panel., B. 02 Nos. 400

Amps , 4 pole, 36 KA microprocessor released based

MCCB suitable for mounting in the above LT panel

board, providing with necessary connection with

thepanel, C. 06 Nos. 200Amps 4P 36 KA

microprocessor released based MCCB suitable for

mounting in the above LT panel board, providing

with necessary connection with the panel, including

internal connection should be stranded copper strips

of suitable size from the bus bar to be provided as

per direction at site Engineer. The design of LV

Panel shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

NFR HQ-ELECTRICAL/N F RLY

3 3 Design, supply , installation , testing and Set 3.00 195478.00 586434.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board as per IEC 61439 2

factory made totally enclosed weather and vermin

proof, suitable ventilated, 440 Volts, 50 HZ, AC

Supply, suitable for 3Phase/4P circuits , protection of

enclosure with pre-treatment and powder coating of

approved colour, with canopy confirming minimum

IP-54 protection , colour of panel shall be RAL 7035

structured finish , modular in construction made of

suitable size, using CRCA Sheet Steel of 2mm

thickness and are Epoxy powder coating having 9

tank process having provision of detachable cable

alleys units in both sides including suitable angle

iron/flat iron frame work supports with 1 set 3 phase

with neutral (TPN) electrolytic grade 400 A COPPER

bus bar and bus bar system shall have heat

shrinkable coloured PVC sleeve having RYB

indication lamp with digital Voltmeter with three row

display system VSS (AE/RISHAB), digital ammeter

with three row display system ASS (AE/RISHAB) CT

250/5A, CL-1.0, base plate, earthing studs, panel

locks, PCC work and making good disturbed surfaces

etc. necessary electrical connections with

new/existing cable complete all as specified and as

directed and comprising of the following

specifications:- A)Supply, fitting, fixing, testing &

Commissioning of 02 no. 200Amp, 4 pole, 36 KA

thermal magnetic based MCCB, suitable for

mounting in the above LT panel board, connection of

incoming supply of copper strips of suitable size

from the bus bar. B) Supply, fitting, fixing, testing &

Commissioning of 06 nos. 125A 4 pole, 25 KA

Adjustable Thermal magnetic releasedbased MCCB

suitable for mounting in the above LT panel board,

connection of incoming supply of copper strips of

suitable size from the bus bar. Specification of Panel

as per Annexure-P(LV panel) of attached tender

document. (Breaking capacity of all MCCB's should

be Ics=100% Icu with adjustable magnetic settings

and MCCB's shall have a rated service voltage up to

690V and rated impulse withstand voltage shall not

be lesser than 8 KV)

NFR HQ-ELECTRICAL/N F RLY

4 4 Design, supply , installation , testing and Set 7.00 167219.00 1170533.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 200 Amps 4 pole, 36 KA microprocessor

released based MCCB suitable for mounting in the

above LT panel board, providing with necessary

connection with the panel, B. 20 Nos. 63 Amps , 4

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

5 5 Carrying, Laying, commissioning of various size Metre 4200.00 32.00 134400.00

Aluminium armoured LT cable partly along the pole

and partly through ground in cable trench with

suitable fixing arrangement. Loading, unloading &

carrying of cable to actual work site by contractor

own arrangement as per instruction of Engineer in-

charge at site. (Cable will be supplied by Railway)

6 6 Excavation for cable trenches in soft soil, depth upto Metre 600.00 622.00 373200.00

1.2 m including dressing of sides lift upto 1.5 m,

including getting out the excavated soil, refilling

with sand and or good soil after laying of cable/ pipe

etc in layers of 20 cm, ramming, watering and

disposal of surplus excavated soil as directed, within

a lead of 50 metres . As DSOR Item No. 14.4

7 7 Supply, installation, testing & commissioning of 40A Numbers 70.00 5055.00 353850.00

4P MCB, B/C SERIES with thermoplastic enclosure as

per direction of site engineer in-charge.

8 8 Supply, Carrying, laying, fitting, fixing & Metre 500.00 111.00 55500.00

commissioning of 63(OD) mm diameter Double wall

corrugated PN-6.0 Kgf/cm2 HDPE Pipe partly through

over ground , partly through underground with ISI

marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II

complete with fitting and cutting, jointing etc. as per

direction of site engineer in charge of Railway.

9 9 Supply, installation, testing, and commissioning of Set 7.00 47256.00 330792.00

an indoor busbar panel equipped with a 200A

busbar, comprising 4 nos of 40A, 4-pole, B/C-curve

MCBs, along with dedicated space and provisions for

the installation of 4 Nos of energy meters.

10 10 Dismantling of existing overhead LT lines with all Each 40.00 556.00 22240.00

accessories without damage from the work site and Span

handing over to concerned SSE office as per

instruction of site Engineer in-charge of railway.

NFR HQ-ELECTRICAL/N F RLY

11 11 Supply, erection of earthing set by 80 mm Dia GI Numbers 80.00 3323.00 265840.00

pipe 4 Mts. long including construction of earth pit

with cover and earth continuity by (25x3)mm GI

strip , GI nuts and bolts etc. as per direction at site

12 12 Supply & erection of GI tubular pole 9.5 Meter long Numbers 10.00 14139.00 141390.00

type410, SP -32 with suitable size step length,

section diameter and sectional thickness as per IS

2713 of 1980 including suitable size of base plate

and cap on top and digging of pit to 1/5th of the pole

height and supply and construction of CC foundation

in ratio 1:2:4 by cement, Sand and Ships of size 19

mm. The CC block will be 30 cm x 30 cm from

bottom of the pole up to 30cm above the GL.

13 13 Supply, fitting, fixing and testing of outdoor type 60 Numbers 60.00 3165.00 189900.00

watts LED street light fitting complete with LED

lamp, bend pipe and all other accessories including

connecting cable and provision of necessary hanging

arrangement etc. as per site requirement. Lumens

output should be greater than 100 Lumens/watt,

LED driver's efficiency should be minimum

90%,Power factor of complete fitting should be

greater than 0.90, Input operating voltage: 140V to

14 14 Excavation of horizontal boring manually for outside Metre 120.00 766.00 91920.00

of the Road/Railway track Embankment at a

minimum distance of 6 meters. From the

embankment GL and depth of 2.0 meters. Below

from G.L. with preparation of site for boring by

placing of pipes for electric cable protection through

contractor own arrangement as per direction of site

15 15 Supply, installation, and laying of G.I. pipe (medium Metre 40.00 2321.00 92840.00

class) of 150 mm (ID) with all necessary accessories

as per requirement at site.

16 16 Supply, installation, and laying of G.I. pipe (medium Metre 40.00 1488.00 59520.00

class) of 100 mm (ID) with all necessary accessories

as per requirement at site.

17 17 Supply, installation, and laying of G.I. pipe (medium Metre 65.00 635.00 41275.00

class) of 50 mm (ID) with all necessary accessories

as per requirement at site.

18 18 Supply, installation, testing and commissioning of Set 50.00 2979.00 148950.00

MS Junction box with 6 A MCB for street light pole

connection with all connecting accessories as per

requirement and direction of site engineer in-

NFR HQ-ELECTRICAL/N F RLY

19 19 Design, supply , installation , testing and Set 2.00 79941.00 159882.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 125 Amps 4 pole, thermal magnetic

based 25KA 4 pole MCCB,suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, B. 4 Nos 40 Amps , 2

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

20 20 Supply and wiring of sub- main line concealed by RM 1850.00 180.00 333000.00

2x10 sq. mm. PVC insulated unsheathed and multi

stranded FRLS Copper Cable confirming to IS

694/1990 through suitable size of PVC conduit pipe

with 1sq. mm unsheathed copper cable as earth

continuity wire.

21 21 Supply, installation, testing and commissioning of a Numbers 38.00 242.00 9196.00

cable route marker consisting of a 10 cm x 10 cm x

5 mm thick galvanized iron (G.I.) plate with custom

inscription, securely bolted or welded to a 35 mm x

35 mm x 6 mm angle iron post (60 cm long),

including excavation and fixing the assembly firmly

in the ground as required.

Item- 4 Part D: Central Gotanagar West Side

S No. Item Description of Item Unit Qty Rate Amount

NFR HQ-ELECTRICAL/N F RLY

1 1 Design, supply , installation , testing and Set 3.00 374156.00 1122468.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 630 Amps comprising with the followings:-

A. 01 Nos. 630 Amps 4P on-load Change over switch

with proper connection to the panel., B. 02 Nos. 400

Amps , 4 pole, 36 KA microprocessor released based

MCCB suitable for mounting in the above LT panel

board, providing with necessary connection with

thepanel, C. 06 Nos. 200Amps 4P 36 KA

microprocessor released based MCCB suitable for

mounting in the above LT panel board, providing

with necessary connection with the panel, including

internal connection should be stranded copper strips

of suitable size from the bus bar to be provided as

per direction at site Engineer. The design of LV

Panel shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

NFR HQ-ELECTRICAL/N F RLY

2 2 Design, supply , installation , testing and Set 5.00 195478.00 977390.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board as per IEC 61439 2

factory made totally enclosed weather and vermin

proof, suitable ventilated, 440 Volts, 50 HZ, AC

Supply, suitable for 3Phase/4P circuits , protection of

enclosure with pre-treatment and powder coating of

approved colour, with canopy confirming minimum

IP-54 protection , colour of panel shall be RAL 7035

structured finish , modular in construction made of

suitable size, using CRCA Sheet Steel of 2mm

thickness and are Epoxy powder coating having 9

tank process having provision of detachable cable

alleys units in both sides including suitable angle

iron/flat iron frame work supports with 1 set 3 phase

with neutral (TPN) electrolytic grade 400 A COPPER

bus bar and bus bar system shall have heat

shrinkable coloured PVC sleeve having RYB

indication lamp with digital Voltmeter with three row

display system VSS (AE/RISHAB), digital ammeter

with three row display system ASS (AE/RISHAB) CT

250/5A, CL-1.0, base plate, earthing studs, panel

locks, PCC work and making good disturbed surfaces

etc. necessary electrical connections with

new/existing cable complete all as specified and as

directed and comprising of the following

specifications:- A)Supply, fitting, fixing, testing &

Commissioning of 02 no. 200Amp, 4 pole, 36 KA

thermal magnetic based MCCB, suitable for

mounting in the above LT panel board, connection of

incoming supply of copper strips of suitable size

from the bus bar. B) Supply, fitting, fixing, testing &

Commissioning of 06 nos. 125A 4 pole, 25 KA

Adjustable Thermal magnetic releasedbased MCCB

suitable for mounting in the above LT panel board,

connection of incoming supply of copper strips of

suitable size from the bus bar. Specification of Panel

as per Annexure-P(LV panel) of attached tender

document. (Breaking capacity of all MCCB's should

be Ics=100% Icu with adjustable magnetic settings

and MCCB's shall have a rated service voltage up to

690V and rated impulse withstand voltage shall not

be lesser than 8 KV)

NFR HQ-ELECTRICAL/N F RLY

3 3 Design, supply , installation , testing and Set 7.00 167219.00 1170533.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board as per IEC 61439 2

factory made totally enclosed weather and vermin

proof, suitable ventilated, 440 Volts, 50 HZ, AC

Supply, suitable for 3Phase/4P circuits , protection of

enclosure with pre-treatment and powder coating of

approved colour, with canopy confirming minimum

IP-54 protection , colour of panel shall be RAL 7035

structured finish , modular in construction made of

suitable size, using CRCA Sheet Steel of 2mm

thickness and are Epoxy powder coating having 9

tank process having provision of detachable cable

alleys units in both sides including suitable angle

iron/flat iron frame work supports with 1 set 3 phase

with neutral (TPN) electrolytic grade 400 A COPPER

bus bar and bus bar system shall have heat

shrinkable coloured PVC sleeve having RYB

indication lamp with digital Voltmeter with three row

display system VSS (AE/RISHAB), digital ammeter

with three row display system ASS (AE/RISHAB) CT

250/5A, CL-1.0, base plate, earthing studs, panel

locks, PCC work and making good disturbed surfaces

etc. necessary electrical connections with

new/existing cable complete all as specified and as

directed and comprising of the following

specifications:- A)Supply, fitting, fixing, testing &

Commissioning of 02 no. 200Amp, 4 pole, 36 KA

thermal magnetic based MCCB, suitable for

mounting in the above LT panel board, connection of

incoming supply of copper strips of suitable size

from the bus bar. B) Supply, fitting, fixing, testing &

Commissioning of 20 nos. 63A 4 pole, 16 KA B/C

series MCB suitable for mounting in the above LT

panel board, connection of incoming supply of

copper strips of suitable size from the bus bar.

Specification of Panel as per Annexure-P(LV panel)

of attached tender document. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings and MCCB's shall have a rated

service voltage up to 690V and rated impulse

withstand voltage shall not be lesser than 8 KV)

4 4 Carrying, Laying, commissioning of various size Metre 3500.00 32.00 112000.00

Aluminium armoured LT cable partly along the pole

and partly through ground in cable trench with

suitable fixing arrangement. Loading, unloading &

carrying of cable to actual work site by contractor

own arrangement as per instruction of Engineer in-

charge at site. (Cable will be supplied by Railway)

5 5 Excavation for cable trenches in soft soil, depth upto Metre 600.00 622.00 373200.00

1.2 m including dressing of sides lift upto 1.5 m,

including getting out the excavated soil, refilling

with sand and or good soil after laying of cable/ pipe

etc in layers of 20 cm, ramming, watering and

disposal of surplus excavated soil as directed, within

a lead of 50 metres . As DSOR Item No. 14.4

6 6 Supply, installation, testing & commissioning of 40A Numbers 70.00 5055.00 353850.00

4P MCB, B/C SERIES with thermoplastic enclosure as

per direction of site engineer in-charge.

7 7 Supply, Carrying, laying, fitting, fixing & Metre 500.00 111.00 55500.00

commissioning of 63(OD) mm diameter Double wall

corrugated PN-6.0 Kgf/cm2 HDPE Pipe partly through

over ground , partly through underground with ISI

marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II

complete with fitting and cutting, jointing etc. as per

direction of site engineer in charge of Railway.

8 8 Supply, installation, testing, and commissioning of Set 4.00 47256.00 189024.00

an indoor busbar panel equipped with a 200A

busbar, comprising 4 nos of 40A, 4-pole, B/C-curve

MCBs, along with dedicated space and provisions for

the installation of 4 Nos of energy meters.

NFR HQ-ELECTRICAL/N F RLY

9 9 Dismantling of existing overhead LT lines with all Each 40.00 556.00 22240.00

accessories without damage from the work site and Span

handing over to concerned SSE office as per

instruction of site Engineer in-charge of railway.

10 10 Supply, erection of earthing set by 80 mm Dia GI Numbers 80.00 3323.00 265840.00

pipe 4 Mts. long including construction of earth pit

with cover and earth continuity by (25x3)mm GI

strip, GI nuts and bolts etc. as per direction at site

11 11 Supply & erection of GI tubular pole 9.5 Meter long Numbers 10.00 14139.00 141390.00

type410, SP -32 with suitable size step length,

section diameter and sectional thickness as per IS

2713 of 1980 including suitable size of base plate

and cap on top and digging of pit to 1/5th of the pole

height and supply and construction of CC foundation

in ratio 1:2:4 by cement, Sand and Ships of size 19

mm. The CC block will be 30 cm x 30 cm from

bottom of the pole up to 30cm above the GL.

12 12 Supply, fitting, fixing and testing of outdoor type 60 Numbers 40.00 3165.00 126600.00

watts LED street light fitting complete with LED

lamp, bend pipe and all other accessories including

connecting cable and provision of necessary hanging

arrangement etc. as per site requirement. Lumens

output should be greater than 100 Lumens/watt,

LED driver's efficiency should be minimum

90%,Power factor of complete fitting should be

greater than 0.90, Input operating voltage: 140V to

13 13 Excavation of horizontal boring manually for outside Metre 100.00 766.00 76600.00

of the Road/Railway track Embankment at a

minimum distance of 6 meters. From the

embankment GL and depth of 2.0 meters. Below

from G.L. with preparation of site for boring by

placing of pipes for electric cable protection through

contractor own arrangement as per direction of site

14 14 Supply, installation, and laying of G.I. pipe (medium Metre 50.00 2359.00 117950.00

class) of 150 mm (ID) with all necessary accessories

as per requirement at site.

15 15 Supply, installation, and laying of G.I. pipe (medium Metre 50.00 1512.00 75600.00

class) of 100 mm (ID) with all necessary accessories

as per requirement at site.

16 16 Supply, installation, and laying of G.I. pipe (medium Metre 85.00 646.00 54910.00

class) of 50 mm (ID) with all necessary accessories

as per requirement at site.

17 17 Supply, installation, testing and commissioning of Set 45.00 2979.00 134055.00

MS Junction box with 6 A MCB for street light pole

connection with all connecting accessories as per

requirement and direction of site engineer in-

NFR HQ-ELECTRICAL/N F RLY

18 18 Design, supply , installation , testing and Set 2.00 79941.00 159882.00

commissioning of floor/ pedestal mounted outdoor

type double door LT Panel Board with canopy

confirming minimum IP-54 protection dust-vermin &

c o r r o s io n p r o o f , chemically treated chemically

treated , and Epoxy powder coated using Sheet

Steel of 2 mm having canopy at TOP & having 1 set

3 phase with neutral copper bus bar chamber

capacity 250 Amps comprising with the followings:-

A. 02 Nos. 125 Amps 4 pole, thermal magnetic

based 25KA 4 pole MCCB,suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, B. 4 Nos 40 Amps , 2

pole, B/C series 10kA MCB suitable for mounting in

the above LT panel board, providing with necessary

connection with the panel, including internal

connection should be stranded copper strips of

suitable size from the bus bar to be provided as per

direction at site Engineer. The design of LV Panel

shall be verified for Internal Arc compliance of

minimum 80 kA for 0.5 sec as per IEC 61641. The LV

panel shall have provision for top/ bottom incoming

and bottom/ top outgoing respectively to suit site

conditions of cable entries (as per the site

requirements to be specified by the End User during

drawing approval) Minimum clearance between

phases /live parts shall be 25 mm and phases /live

parts/ neutral to ground shall be 19 mm except on

the equipment terminals. The busbars shall be

supported of regular intervals using SMC or DMC

insulators as per the tested design. It should have

minimum Comparative Tracking Index (CTI) of 600 V

as per IS 2824). The LV panel manufacturer

(Franchise) shall be ISO 9001/9002 certified. The

drawings of the LV Panels to be vetted with sign-

stamp by the Switchgear OEM. (Breaking capacity of

all MCCB's should be Ics=100% Icu with adjustable

magnetic settings.)

19 19 Supply and wiring of sub- main line concealed by RM 1580.00 180.00 284400.00

2x10 sq. mm. PVC insulated unsheathed and multi

stranded FRLS Copper Cable confirming to IS

694/1990 through suitable size of PVC conduit pipe

with 1sq. mm unsheathed copper cable as earth

continuity wire.

20 20 Supply, installation, testing and commissioning of a Numbers 32.00 242.00 7744.00

cable route marker consisting of a 10 cm x 10 cm x

5 mm thick galvanized iron (G.I.) plate with custom

inscription, securely bolted or welded to a 35 mm x

35 mm x 6 mm angle iron post (60 cm long),

including excavation and fixing the assembly firmly

in the ground as required.