SPECIAL REPAIRS TO BLDG NO T-18, T-39 (ASSEY LINES), DRAINAGE SYSTEM AND PROVN OF HARDSTANDING NEAR T-37 AT AURANGABAD MIL STN UNDER GE (S) AHMEDNAGAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level all as specified and as directed.

Demolition of brick/block work or stone boulder masonry built in cement or cement lime mortar etc all as specified and as directed

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 Sqcm in section, in any position all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area not exceeding 1.5 sq. m each all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area exceeding 1.5 sq. m but not exceeding 4 sqm each all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling asbestos cement (Corrugated, Semi-corrugated etc.) sheets in roof coverings all as specified and as directed.

Dismanlting floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviciable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling of stone slabs, interlocking paver blocks of any description or thickness in floors, aprons laid bedded and pointed in any mortar etc complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re- fixing all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re- fixing all as specified and as directed.

Demolition and breaking up drain pipe of 300 mm dia and of any description at any location complete all as specified and directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified and as directed

Excavation in trenches, n exc 1.50m wide and n exc 1.50m in depth; for foundations, etc. or for manholes etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick with soils all as specified and as directed.

Removing excavated soil to distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

M&L for hardcore of gauge n exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified and as directed.

M&L for PCC, 1:4:8, type D2, using 40 mm graded stone aggregates as in foundations, filling and mass concrete all as specified and as directed.

M&L for PCC, 1:3:6 type C2, using 40 mm graded stone aggregates as in surface channels and drain all as specified and as directed.

M&L for precast RCC 1:2:4, type B-1 using 20 mm graded stone aggregates as in cover slabs of manholes including necessary forms, moulds etc complete all as specified and as directed

M&L for precast cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) in kerb stones, of size 300 mm x 150 mm x 300 mm, machine made with plain fair faces, including chamfers weatherings, throating etc. and setting cement mortar 1:6 complete with joints to matchcomplete all as specified and directed.

M&L for brick work with sub class B bricks, old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

S&F of solid PVC door frame of size 50mm x 47mm made out of 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face all as specified and as directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet Polyurethane painted on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specifications & drawing all as specified and as directed.

S&F 35mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

S&F 35 mm thick, second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel, and fixed all as specified and as directed.

S&F 75 mm size butt hinges, medium weight, cold rolled mild steel, and fixed all as specified and as directed.

S&F 300 mm long mild steel, ordinary rat tail rod pattern helical door spring including roller and roller plate complete all as specified and as directed.

S&F Aluminium anodised tower bolt of extruded section of 150 mm size, complete all as specified and as directed.

S&F Aluminium handle cast type anodised, 125 mm size, fixed complete all as specified and as directed.

S&F for mild steel pressed handles 150 mm long oval type ,stoves enamelled black complete all as specified and as directed.

S&F mild steel sliding door bolt 300 mm long stove enamelled black with bright bolt not less than 16 mm dia with & including a minimum of 6 bolts & nuts four on bolt plate and two on staple plate complete all as specified & as directed.

S&F mild steel barrel tower bolts 200mm long stove enamelled black, with bright bolts complete all as specified and as directed.

S & F in repairs tubular towel rail, 20mm dia, D type, 60cm long between flanges, Brass chromium plated fixed with and including Chromium plated brass screws and wooden/plastic cleats. complete all as specified and directed.

S&F in repairs, harrison curtain rails 20mm dia, mild steel, plastic coated, fancy type with and including fixing brackets, stops etc complete wooden or PVC plug all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18mm and fixed complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally, hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc Fe 410 -W (Gde- E- 250) quality- A

S&F rolled mild steel plates (Plain or Chequred) channels, square cut or notched, forming holes, with riveted, bolted or welded attachment confirming to Fe 410 -O or Fe 310 - O all as specified and as directed.

M&L for mild steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and as directed.

M&L for mild steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and as directed.

M&L for mild steel ventilators with top hung shutters including hinges with steel handle, and steel peg stay, complete all as specified and as directed.

M&L for mild steel framed work such as grills, grating, guard bars etc with end of bars shoulderd and/or riveted, welded or forged into spikes, framed guard bars iron doors and similar work conforming to Fe 290 Gde E-165 all as specified and as directed.

S&F mild steel screw bolts (machine made), 10 to 16mm dia of neck and n exc 100mm long with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, fixed to posts complete all as specified and as directed.

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe 410-W(Gde-E- 250) quality-A complete all as specified and as directed.

M&L for mild steel work as in wind ties for roof sheets including securing bolts complete including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F 9mm thick primium quality laminated PVC tiles 600mm x 600 mm in ceilling fixed with screws, including GI frame work for false ceiling, comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to center/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm seuspended from soffit at approx 900 mm center to center GI cleat and steel expansion fasteners with and including ceilling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to center frame work including hanger 6 mm dia GI wire upto 1200 mm length adjustable level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40x3mm size 60mm long including dismantling existing false ceiling boards, hangers & framework etc complete all as specified and as directed.

M&L for prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

M&L for prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/ridges/valley gutters/cladding to wall, fixed with self tapping screws as specified ad as directed.

M&L for 75mm thick PCC 1:4:8, type D2 using 40 mm graded stone aggregates as in sub base all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D2 using 40 mm graded stone aggregates as in sub base all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 18 to 20mm thick granite of any type work (table rubbed and polishing) in steps, jambs, pillars, window cill, cooking platform and like in CM(1:4) including pointing to white cement (1:2) using marble dust with admixture of pigment to match the shade of granite complete all as specified and as directed.

Rounding the edges of stone slabs one edge, such as in steps, cooking platform, and other similar situation complete all as specified and as directed.

M&L for machine cut kota stone flooring, 20-25 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per serial item No. 58 but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including10 mm thick backing coat of cement mortar (1:4) complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm, shade as approved by GE, as in floors etc., laid over and including 15mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm, shade as approved by GE, as in floors etc., laid over and including 15mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for glazed ceramic coloured (plain or printed) tiles of size 350x 250x 7 mm/ 450X 350X 7mm thick on vertical surfaces such as in skiting/dado over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L for vitrified coloured ceramic tiles,10 mm thick (square / rectangular), area of each tile exc 0.36sqm but n exc 0.42sqm, shade as approved by GE in floor etc laid over and including 20 mm thick bedding layer in cement mortar 1:6, jointed in grey cement slurry and pointed in white or coloured cement to match with colour of tiles all as specified and as directed.

All as per serial item No 63 above but in dado / skirting or on vertical surfaces, laid over and including 10mm thick backing coat in cement mortar 1:4 .

M&L for precast cement concrete interlocking paver blocks (glossy finish/ rubber matt finish) of 60 mm thick ,hydraulically pressed, cemented blocks of grey cement with pigments,(glossy finish/ rubber mat finish), factory made, M-35 grade as in floor, laid over & including 25 mm thick sand cusion and including filling of interstices with fine sand complete all as specified and as directed. Note Size, shape & pattern of tiles shall be as decided.

M&L for precast cement concrete interlocking paver blocks (glossy finish/ rubber matt finish) of 80 mm thick ,hydraulically pressed, cemented blocks of grey cement with pigments,(glossy finish/ rubber mat finish), factory made, M-40 grade as in floor, laid over & including 25 mm thick sand cusion and including filling of interstices with fine sand complete all as specified and as directed. Note Size, shape & pattern of tiles shall be as decided.

M&L for 10mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces, finished even and smooth with thin layer of sagol complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished surfaces even and fair all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whiting all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and as directed

M & L for complete removal of existing treatment, preparation of surfaces of walls and applying a coat of 1 mm thick (average) white cement putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper over a coat of primer complete all specified and as directed

M&L for preparation of old decorated plastered surface of walls and applying one coat of cement base paint complete all as specified and as directed

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane all as specified and as directed

M&L for preparing new wood or wood based surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed

M&L for preparing new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and as directed.

M&L for 15 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

M&L for 20 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F in repairs, bib tap, 15mm bore cast copper alloy chromium plated, fancy type with crutch or butter- fly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs, stop valves, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repairs, stop valves, 20mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repairs, pillar taps, 15mm bore, cast copper alloy with capstan heads, fancy type, chromium plated, screwed down, high pressure with with or without lettered HOT or COLD with long screwed shanks and fly nuts screwed for for iron pipe or unions complete all as specified and as directed.

S&F in repairs, brass chromium plated swivel shower rose, 125mm size, including shower arm fixed to steel pipe and union, complete all as specified and as directed.

S&F in repairs Chromium plated health faucet with 1 metre flexible tube & hook complete and fixed complete all as specified and as directed.

S&F in repairs 450 mm long PVC connection, 15mm size with PTMT nuts complete all as specified and as directed.

S&F in repairs, 32mm bore low density polythene pipe (LDPE) of pressure rating 6kgf/Sqcm including fittings fixed to wall or laid in floors etc complete all as specified and as directed.

M&L in repairs grating doom 100mm dia PTMT all as specified and as directed.

S&F in repairs vitreous china wash hand basin, white flat back size 580 mm x 450 mm including brackets including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection 450mm long complete all as specified and as directed.

S&F in repairs, vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest, P or S trap, set in cement concrete including flush pipe and connecting to trap / flushing cistren and making good to floor complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S & F in repairs PVC low level flushing cistern, 10 ltrs capacity including ball valve, bracket inlet, PVC pipe, PVC connection 600 mm long etc.complete all as specified and as directed.

S&F in repairs, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed

S&F in repairs, wall corner sheet glass shelf assembly, size 12"x12" with 5mm thick toughened glass with all fittings complete all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 75 mm dia PVC (SWR) bends wih oval access door complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) bends with access door of any radius complete all as specified and as directed

M&L in repairs, for PVC (SWR) nahani trap/floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type (1:2:4) type B1all as specified and as directed.

S & F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes ; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm.incl down take pipe and coupling CP complete fixed complete all as specified and as directed.

M&L for reinforced concrete pipes 300mm dia class NP2 laid and jointed complete with collars all as specified and as directed

M&L for concrete bed 1:4:8 type D2 to drain pipes 300mm dia including packing under and completely surrounding pipes with concrete after laid as specified and as directed

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc and making good disturbed surfaces of walls, floors etc as directed.

M&L for point wiring (Light Point complete with 1.5 Sqmm single core ,multistranded ,copper conductor FRLS , PVC insulated and unsheathed cable 650/1100 volts grade, confirming to IS-694 1990,drawn through and including PVC Casing Capping of size 25 mm /20 mm dia with all accessories as specified with modular cover plate with frame and modular metal flux boxes/rectangular PVC board for mounting fitting & fixtures like switches sockets and fan regulators etc including copper earth continuity wire for PVC insulated of size 1.5 Sqmm for one light Point controlled by one way Switch complete all as specified and as directed .

All as per serial item No.105 above but for one fan point controlled by one way switch and regulator complete all as specified and as directed.

All as per serial item No.105 above but for one bell point with cables 1.5sqmm complete all as specified and as directed.

All as per serial item No.105 but for 5 Amps Socket in same Board with 1.5 sq mm cable complete all as specified and as directed

All as per serial item No.105 but for 5 Amps Socket in independent board with 1.5 Sqmm Cable complete all as specified and as directed .

All as per serial item No.105 above but for power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 2.5 Sqmm on independent board incl one run 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall incl including PVC box 2 mm complete all as specified and as directed

S&F modular switch single pole one way 6/10 Amps 1 module complete all as specified and as directed

S&F modular switch single pole one way 16 Amps 1 module complete all as specified and as directed

M&L in replacement of modular socket 6 amp-2/3 pin combined 2 module complete all as specified and as directed

M&L for modular socket 6 A/16 amp -2/3 pin combined 2 module complete all as specified and as directed

S&F ceiling rose surface bakelite three terminal type complete all as specified and as directed

S&F modular fan regulator step type ,120W -2 module complete all as Specified & as directed

S&F LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F in replacement decorative ultra slim square profile LED lighting fixyure with extruded polycarbonate,environmental friendly , energy efficient of capacity 18 Watt , appx 4 feet long, 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed

S&F in replacement decorative ultra slim square profile LED lighting fixyure with extruded polycarbonate,environmental friendly , energy efficient of capacity 10 Watt , appx 2 feet long,3000 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed

S&F in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F in replacement lamp LED 9/10 Watt, 230 volts 50 Hz AC complete all as specified and as directed

S&F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and as directed.

S&F electrical bell (multi music type), AC, 230 Volts complete all as specified and as directed

S&F electrical bell push modular type 6 Amp complete all as specified and as directed

S&F 35/40 Watt building mounted LED security light fitting complete made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2 m long bend to shape required fixed to pole / wall with 02 Nos mild steel clamps made out of flat iron 40 x 5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting, complete all as specified and as directed

S&F LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed

S&F in replacement MCB DB double door 4 way TPN with suitable rated busbar 240 V complete all as specified and as directed

S&F in replacement MCB DB double door 8 way SPN with suitable rated busbar 240 V complete all as specified and as directed

S&F in replacement MCB DB double door 12 way SPN with suitable rated busbar 240 V complete all as specified and as directed.

S&F MCB single pole 240 volts 6 to 32 Amps "C" curve complete all as specified and as directed

S&F in replacement of MCB SPN, C Curve, 40-63 Amps 10 KA single pole AC 230 volts complete all as specified and as directed.

S&F MCB TPN 415 volts 63-100 Amps "C" curve complete all as specified and as directed

S&F MCB TPN 415 Volts 40 Amps "C" Curve complete all as specified and as directed

Supply, laying, jointing and testing PVC XLPE insulated armored heavy duty electric cable with aluminum conductor, 1100 volt grade, cross sectional area 50 Sqmm 3.5 Core laid in trenches/ on wall complete all as specified and as directed

Supply and spreading sand for cusioning for electric cable 8 cm below the cable and 15 cm above the cable complete all as specified.

S&F in replacement unreinforced precast concrete cable cover class LV type-1 flat size 250 mm x 150 mm x 40 mm complete all as specified and as directed.

S&F in repairs GI tubing light grade of 40 mm dia for cable protection on pole/wall/floor/ or in trenches and drain etc complete with necessary clamp, nut, bolts and washers and socket and making good the disturbed surface of wall , floor or roof etc all as specified and as directed

S&F in replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240 Volts complete all as specified and as directed

M&L for sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC Cassing Capping (ISI marked) with all accessories such as Tees, Elbows, junction box etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/ caping/ Conduit, complete all as specified and as directed. Note : Two runs of 4.0 Sqmm cable, one run of 4.0 Sqmm cable and one run of PVC casing/caping will be measured as one Rm unit.

M&L for sub main wiring with 2 runs of 2.5 Sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size casing / caping (ISI marked) with all accessories such as Tees, Elbows, junction box etc as requied alongwith one run of 2.5 Sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of casing/caping, complete all as specified and as directed. Note : Two runs of 2.5 Sqmm cable, one run of 2.5 Sqmm cable and one run of PVC casing/caping will be measured as one Rm unit.

M&L for earthing complete with galvanised steel earth plate electrode, 60cm x 60cm x 6.3 mm thick, burried directly in ground(earth pit not less than 2.25metre deep below normal ground level) with top edge of earth plate not less than 1.5 metre below normal ground level, connected to and including galvanised earth lead wire of 4 mm dia from earth pit to each qtr DB by means of nuts & bolts, check nuts and washers of galvanised including PCC pit of 1:2:4, type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, mild steel angle iron 25 x 25 x 3mm in frame, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate no 3 of MES sch 2009 (Part I), including taking down old earthing connected main switch board all as specified and testing on completion.

sonu enterprises

M/S Tirupati Goroba Shendge

M/s S.R lahoti

M/S. M.A. Sharief engineers and contractors