GE/S(U)-03/2020-21 SPL REPAIR OF ROOF TREATMENT OF BLDG NO P-196 BN STORE AT 4 PARA SF BLDG NO NP-72 EXEC BR BLDG NO T-82 FURNITURE STORE

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position etc complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in slab supported on walls/ chajjas and the like complete all as specified and directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200 mm thick surface horizontal or sloping complete all as specified and directed.

TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor and finished even and fair complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 laying floor finishes complete all as specified and directed.

Non skid coloured ceramic tiles (square/ rectangular) 8 to 9 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

10 mm thick rendering on fair faces of brick/ concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles complete all as specified and directed.

Glazed coloured ceramic tiles in dado/vertical surface (300 x 600 mm x 7 mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Rendering 15 mm thick in two layer (10 mm + 5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed. Note:- Water proofing compound to be measured and paid for separately.

Rendering 10 mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 5 mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed.

Preparation new surfaces plastered or unplastered and applying three coats of white wash on ceiling complete all as specified and directed.

Preparation of newly plaster surfaces of wall and applying three coats of white wash complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in-Charge.

Factory made mild steel ventilators box type with upper top hung with glazed and gaused shutters and bottom openable, locking arrangements type shutters including pintol hinges, steel peg stay and one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 (ii) Glazing, wire gauge and Glass shall be measured and paid for separately.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks, Cup Board etc and similar work confirming to Fe 290 Gd E-165 complete all as specified and directed.

Rolled mild steel work of angle iron as in frames of doors & Cup Board etc confirming to grade Fe 410-O or Fe-310-O complete all as specified and directed.

75 mm butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

4 mm thick figured glass (frosted), pin head type and glazing with oil putty not exceeding 0.50 Sqm in each pane fixing to window/ ventilator complete all as specified and directed.

Galvanised Mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. (ISI Mark)

150 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. (ISI Mark)

150 mm aluminium handles, cast type anodised complete all as specified and directed. (ISI Mark)

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm both side Prelam PVC sheet used instead of plain colour PVC Sheet and edge will be painted to match with prelam sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified and directed.

Factory made solid panel PVC door shutter 28 to 30 mm thick style, with 2, 4 or 6 raised panel design with 2 mm thick Moulded prelam PVC sheet on the front face and 2 mm Prelam PVC sheet on back face complete all as specified and directed.

Preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of zink chrome primer complete all as specified and directed.

Demolition of brick/stone masonry built in CM including all quoins, arches, pillars, dressed stone work and precasr concrete articles complete all as specified and directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 bricks complete all as specified and directed.

Roughing surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3.0 Kg/sqm including 10 mm thick flooring in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately) complete all as specified and directed.

Applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Min wt of memebrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm and applying aluminium Paint complete all as specified and directed by Engr-in-Charge.

Providing 50 mm thick cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 550 x 400 mm excluding tap, chain, plug but including brackets, waste fitting 32 mm dia, brass chromimium plated for glazed ware sink, basin, with pedestal, long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed in repair complete all as specified and directed.

Water closet (Orissa pattern) including lime concrete bedding, vitreous china long pan orissa pattern 580 x 440 mm, white with integral foot rests (excluding flushing cistern and flush pipe) fixed in repairs complete all as specified and directed.

10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connetion to pipe but fixed in repair complete all as specified and directed.

Aluminium tubular towel rail, 20 mm dia, D type, 60 cm long between flanges aluminium anodized, fixed with rawl plugs in repairs complete all as specified and directed. (ISI Mark)

Steel peg set colour coated of six as per sample in repairs complete all as specified and directed.

Dismantling cast iron pipe and reinforced concrete drain pipes, jointed in cement mortar of any dia taking out from trenches or fixed to wall upto 100 mm complete all as specified and directed.

100 mm Cast iron soil sand cast pipes, waste and vent in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.(ISI Marks).

75 mm Cast iron soil sand cast pipes, waste and vent in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed. (ISI Marks)

100 mm Cast iron soil sand cast pipes, waste and vent in any length with or without ears, with cement joints, fixed to wall complete all as specified and directed.

75 mm Cast iron soil sand cast pipes, waste and vent in any length with or without ears, with cement joints, laid in wall complete all as specified and directed.

50 mm Cast iron soil sand cast pipes, waste and vent in any length with or without ears, with cement joints, fixed to wall complete all as specified and directed.

Salt glazed stone ware gully traps square or round mouthed, type P of size 150 x 150 mm set and jointed to drain pipe with cement mortar (1:1) including demolition of old unserviceable gully traps complete all as specified and directed. (ISI Marks).

Cast iron bends (any radius diminishing pieces or tapes (larger bore measured), 75 mm bore fitted with oval access door fixed with rubber ring joints as in repairs complete all as specified and directed.

Cast iron bends (any radius diminishing pieces or tapes (larger bore measured), 100 mm bore fitted with oval access door fixed with rubber rings joints as in repairs complete all as specified and directed.

75 mm Cast iron floor traps with grating including jointing to waste pipe fixed concrete type B-1 (1:2:4) complete all as specified and directed. (ISI Mark)

Cast iron branch pieces, single/double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100 bore, fitted with oval access door as in repairs complete all as specified and directed.

Cast iron branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 75 mm bore, fitted with oval access door as in repairs complete all as specified and directed.

50 mm Cast iron cowls complete all as specified and directed.

Cast iron Reducer 100 mm for connecting and fixing gas pipe on walls as in repairs complete all as specified and directed.

Cast iron Reducer 75 mm for connecting and fixing gas pipe on walls as in repairs complete all as specified and directed.

Dismantling AC (corrugated or semi corrugated etc) sheet in roof covering including ridges complete all as specified and directed.

Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.60 mm thick of an colour having tensile strength 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and directed.

Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.60 mm thick of an colour having tensile strength 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and directed as in ridge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Roof trusses (framed), trussed, purlins,crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle, channel or flat section) including distance pieces complete all as specified and directed.

Preparation of surfaces and applying two coats of cement base paint on walls complete all as specified and directed.

Viterious china urinals half stall white including CP urinal Spray Nozzal complete including providing and fixing of plug bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and including 60 mm long brass screws pointing including 60 mm long brass complete all as specified and directed.

Taking down 15 mm bore steel tubing and connections including all fittings and removing to store complete all as specified and directed.

Taking down 20 mm bore steel tubing and connections including all fittings and removing to store complete all as specified and directed.

15 mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls including concealed and or laid under floors etc complete complete all as specified and directed.

20 mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15 mm in repair complete all as specified and directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20 mm in repair complete all as specified and directed.

Chromium plated cancealed stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions chromium plated of size 15 mm in repair complete all as specified and directed.

Pillar tap, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered ('Hot' or 'Cold') with long screwed shanks and fly nuts screwed for iron pipe and fixed of bore dia 15 mm in repair complete all as specified and directed.

Bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe of size 15 mm bore chromium plated in repair complete all as specified and directed.

Ball Valves high pressure 20 mm bore of pipe of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed in repair (Minimum weight 20 mm-210 grms) complete all as specified and directed.

Brass chromium plated shower rose 75 mm size with swivel joint fixed to pipe or union of 15 mm bore in repair complete all as specified and directed.

Dismantling water tanks exceeding 500 Ltr capacity but not exceeding 1000 ltr complete all as specified and directed.

Rotational moulded polyethylene water storage tanks with thereded head (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 liters including all accessories complete all as specified and directed.

15 mm bore chromium plated concealed stop cock fancy type long shank and cup complete all as specified and directed.

Soap dish chromium plated fixed with brass screws and wooden/plastic cleats complete all as specified and directed.

PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth in any type of soil/strata for foundation etc or for shafts, wells, drain pipes and getting out complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing surplus spoil to a distance not exceeding 50 m and deposited where directed at a level not exceeding 1.50 m above the starting point complete all as specified and directed.

Providing 200 mm bore pipe concre bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested in mix 1:3:6 type C-2 (using 40 mm graded stone aggregates) complete all as specified and directed.

200 mm bore Reinforced concrete pipes, class NP-2, laid and jointed complete with coller all as specified and directed.

Demolition of reinforced cement concrete in roof floor (other than ground floors) beams staircase, shelf landing chajja etc and similar work complete all as specified and directed.

Providing precast cement concrete type B-1 1:2:4 (using 20 mm graded crused stone aggregate) in landings, cover slab, shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed.

Rendering 10 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones, bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 (using 20 mm graded crused stone aggregate) complete all as specified and directed.

PCC 1:3:6 type C-2 (using 40 mm graded aggregate) in surafce channel and drains complete all as specified and directed.

Extra for forming fair finished drain or channel exceeding 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc complete all as specified and directed.

Rolled Mild steel joist channels, angle or tee sections, fixed indepently witout connecting plates etc. (cut to ordinary length, fixed with hold fast and nails to floors and similar work welding & drilling of holes to floor for fixing of hold fast as per requirement of gde Fe-410W (Gde E-250 quality) complete all as specified and directed by Engr-in-Charge.

AC designer composite ceiling board 4 to 6 mm thick in 600 x 600 mm panel confirming to IS-14682 type-B category-3 including GI frame, holdfast and suspenders complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Pressed steel frames made of 1.25 mm thick MS sheet of profile 105 x 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

Factory made 35 mm thick 2nd class hardwood (Hollock), plain framed, panelled shutters (two panels) with lock rail and panels of 9 mm thick BWP ply or of 12 mm thick BWR grade veneered particle board medium density, with commercial veneering on both faces. The size of rail and stile as per IS : 1003 part- I, klin seasoned and chemically pressure treated complete all as specified and directed.

300 mm long aluminium anodized sliding door bolt with hasp, staple (bolt type) and fixing clips, bolts and sliding bolts etc. complete all as specified and directed.

Mild steel 150 mm ordinary rat and tail springs (Helical door springs) welded or screwed to any type of door frames including roller and roller plate complete all as specified and directed.

Demolition cement concrete in ground floors and paving (unreinforced) not exceeding 15 cm thickness (below or above ground floor) complete all as specified and directed.

75 mm thick plain cement concrete, type C-2, (1:3:6) (using 40 mm graded aggregate) as in plinth protection complete all as specified and directed.

Providing 100 mm thick, plain cement concrete type B-2, (1:2:4) (using 40 mm graded aggregate) as in floors laid in separate bays complete all as specified and directed.

Cement concrete 75 mm thick in sub-base type D-2 1:4:8 (40 mm graded aggregate) complete all as specified and directed.

Coloured machine vibro mechenically floated glossy finish interlocking cement paver block, any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with, topping of cement mixed with imported pigment, colour and shape shall be approved and complete all as specified and directed by Engr-in-Charge. ISI Marked.

Screed bed or bedding layer of mortar 10 mm thick for laying floor tiles in CM 1:4 complete all as specified and directed.

Non skid ceramic joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the slurry complete all as specified and directed.

Preparation of new plastered or un-plastered surfaces and walls including cornices, pilasters etc and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and apply two coat of oil bound distemper over a coat of primer including two coats of wall care putty wall care putty complete all as specified and directed.

Preparation of new wooden or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint ccomplete all as specified and directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty in square pane complete all as specified and directed.

Framed work such as grills gratings etc with ends of bars shouldered and or riveted or forged into spikes framed guard bars and similar works confirming to E-250 grade complete all as specified and directed.

Preparation of old steel surface and aplying one coats of synthetic enamel paint of any description exceeding 10 cm width or girth complete all as specified and directed.

Preparation of new steel surface and applying two coats of synthetic enamel paint of any description exceeding 10 cm width or girth complete all as specified and directed.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement:2 coarse sand) to match the existing floor complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position complete all as specified and directed.

Screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 laying floor finishes complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

50 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregates) as in foundations filling and mass concrete complete all as specified and directed.

Sand cushioning under floors including watering and consolidation complete all as specified and directed.

Pressed steel frames made of 1.25 mm thick MS sheet of profile 125 X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

Factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and directed.

Rendering 15 mm thick cement plaster in cement mortar 1:6 finished even and smooth without using extra cement (internal plaster) complete all as specified and directed.

Steel window (box type) with gaused shutter factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/ 2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge, Glass shall be measured and paid separately.

Description all as per ser item No 126 but without glazing bar complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steelwire staples or complete all as specified and directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down cement/tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10 mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Minimum weight of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of aluminum paint complete all as specified and directed by Engr-in- Charge.

PCC type B-0, 1:2:4 (12.5 mm graded stone agg) to provide the slope of roof complete all as specified and directed.

Preparing new surfaces, plastered or unplastered of wall and applying two coats of weather proof exterior paint (Apex Ultima) on any surface as approved and complete all as specified and directed by Engr-in-Charge.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out any type of soil complete all as specified and directed.

Hardcore of broken stone or boulders of gauge exceeding 63 mm but not exceeding 100 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface complete all as specified and directed.

100 thick PCC 1:2:4 type B-2 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

Excavation in Post holes hard/dense soil(or similar holes) each not exceeding 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

Cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregates) as in Post, column, piller boundry piller including caps and bases complete all as specified and directed.

Steel work in any type of Hollo/rectangular/ Square tubular trusses, Post and other including special shaped washer etc, complete using ERW or induction butt welded tubes confirming to IS-S.1161-1979 grade St-240 complete all as specified and directed.

MS plate or girders Fe-410-W Grade E-250 Quality B fixed with truss col or any independent structure complete necessary welding cutting drilling etc complete all as specified and directed.

100 mm thick Cement concrete type C-2 1:3:6 (using 40 mm graded crushed stone aggregates) on flooring complete all as specified and directed.

Cement concrete type B-1 1:2:4 (using 20 mm graded crushed stone aggregates) support Walls, coping parapets railing, kerbs and other smilar works including forms works any shapeand size complete all as specified and directed.

Cement concrete type B-1 1:2:4, (using 20 mm graded crushed stone aggregates) pre cast kerbs stone set in cement 1;4 and other smilar works including forms works any shape and size complete all as specified and directed.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed.

Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable 1100V grade in and including not less than 2.00 mm thick and 20 mm dia Non metallic Rigid PVC surface/Concealed Conduit (ISI marked) with and all accessories 1.5 mm thick mild steel terminal boxes concealed on walls, painting the same inside and out side with one coat of black bitumen paint with 3 mm thick hylam brand bakelite sheet cover for fixing of piano switches/ sockets/regulator etc along with PVC insulated and unsheathed FRLS 1.5 sqmm multi stranded copper conductor cable (green color) as earth lead & connected to common earth and earthdolly, making good the disturbed surface to match with the existing specification complete all as specified and directed by Engr-in-Charge. Make - KEI or equivalent make in polycab/finolex

All as per ser item No 143 but for one 3 pin 5 Amp socket outlet point controlled by one push button on same board complete all as specified and directed. Make - Anchor or equivalent make in polycab/Havells

All as per ser item No 143 but for one 3 pin 5 Amp socket outlet point controlled by one push button on independent board complete all as specified and directed. Make - Anchor or equivalent make in polycab/Havells

All as per ser item No 143 but for one 3 pin 15A socket outlet on independent Board with PVC insulated unsheathed FRLS cable 4 sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly complete all as specified and directed. Make - Anchor or equivalent make in polycab /finolex

Switch piano flush button single pole one way 5 amps 240 volt in repair complete all as specified and directed.

Socket outlet 2 in 1, 3 pin, 5A, 240 Volt in repair complete all as specified and directed.

Switch socket combination 5 Amps 2-in-1, 5 Pin flush type, 230 volts in repair complete all as specified and directed.

Switch socket combination 5 pin 16 amp, flush type in repair complete all as specified and directed.

Ceiling rose surface bakelite 3 terminals in repair complete all as specified and directed. Make : Cona Cat Part No 2126/SSK Cat Part No 572 or equivalent of make in Havells/ Anchor/Kolors.

LED tube light fitting 4 feet Garnet 20W Batten LED, Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection using flexible cable of suitable size from ceiling rose to fitting complete all as specified and directed. Make - Wipro, Product code - D532065 or equivalent make in C&S/Havells

LED tube light fitting 2 feet Garnet 10W Batten LED, Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection with suitable size flexible cable from ceiling rose to fitting complete all as specified and directed. Make - Wipro, Product code - D531065 or equivalent make in C&S/Havells

9 watt LED Bulk Head fitting complete making all connection using flexible cable of suitable size from ceiling rose to fitting complete all as per the directions of Engr-in-Charge. Make - Syska LED Cat Part No - SSk-BH-9W or equivalent make in Havells/wipro/C&S.

Replacement Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately.

Replacement MCB Single Pole, 230 Volt, B-Series, Raiting 6 to 32 Amps complete all as specified and directed. Cat Part No : 811015 Make : Indoasian or equivalent make in Havells/Legrand. Note : MCBs reuired to fix in existing DBs

Replacement MCB Single Pole and Neutral , 230 Volt, B-Series, Raiting 6-32A complete all as specified and directed. Make : Indoasian Cat Part No 811034 or equivalent make in Havells/Legrand.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.30 mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below normal ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead 4 mm dia by means of bolts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and indicated and testing on completion including excavation earth work drilling holes for electrode PCC pit and cover, funnel, water pipe lugs GI pipe medium grade protection pipe for earth lead up to DBs complete all as specified and directed.

Exhaust fan 250 mm sweep SP, AC, 230V, plastic body alongwith Louvers including making hole of suitable dia in existing wall and all necessary connection from ceiling rose to fan complete all as specified and directed by Engr-in-Charge.

Trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 2 core size including taking out old unserviceable UG cable any type/size complete all as specified and directed.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

GI tubing light grade 40 mm dia along the wall /in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and directed.

Point wiring for one light/fan and bell/wall fan/ engagement light point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes and metal back plate for mounting modular type in adequate module of switches, sockets and regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed.

All as per ser item No 164 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 164 but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 164 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Socket 3 Pin 6 Amps flush type complete all as specified and directed.

Socket combined 2-in-1, 3 Pin 6 & 16 Amps flush type (Modular Type) with outer strip complete all as specified and directed.

Ceiling rose, surface bakelite 65 x 50 mm two to three terminals fixed on PVC Round Block complete all as specified and directed.

Replacement of fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and directed. Make : Anchor/Legrand/Kinjal.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately.

Replacement MCB Single Pole and Neutral , 230 Volt, Raiting 40 to 63 Amps complete all as specified and directed. Make : Indoasian /Standard/Legrand

Replacement sheet metal enclosures for DBs when MCBs to be used double door DB TPN 4 way 415 volts with 200 amps rated bus bar complete all as specified and directed. Make : C&S/Indoasian/Legrand.

Replacement MCB TPN 415 volts, 10 KA, 4 Pole 63 Amps 'C' Curve Opti Pro complete all as specified and directed. Make : C&S/ Indoasian/Legrand.

Replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) 230 Volts wall/surface mounted complete with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge. Make : Havelles Cat Part No. LHEOAOP7UZ6W010 or equivalent Wipro/Bajaj

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W complete all as specified and directed by Engineer-in-Charge. Make- Havells Cat Part No LHEXBXPNIN1W020 or equivalent to Polycab/HPL/Bajaj

36 W LED Endura Slip Proplus 2 x 2 edge-lit luminaire suitable for armstrong/rigit ceiling complete with separate electronic driver complete all as specified and directed. Make : Havells Cat Part No - ENDURASLIMPROPLUS2X2PLR28 /36WLED840MOD or equivalent Wipro/Bajaj

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 4 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire.

Trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 16 Sqmm x 4 core size complete all as specified and directed including taking down old cable. Note : Earth work and other connected work shall be measured and paid sperately.

Switch socket combination 2-in-1 pin 5 Amps flush type complete all as specified and directed.

Switch socket combination 2-in-1, 3 pin 5 & 15 Amps flush type complete all as specified and directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately.

LED Street light 30 W including angle arms (Bracket) with 25 mm dia GI pipe complete all as specified and directed by Engineer-in-Charge. Make - Wipro Product Code - D923065 or equivalent to Havells/HPL/Bajaj

Taking down Ceiling Fan/Exhaust Fan including disconnection of existing connection, dismanting of blades and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and rehanging the fan complete all as specified and directed.

RAMAN CONSTRUCTION CO

jyoti parkash sharma