Providing Basic Amenities near Elakurichi Adaikalamatha shrine in Ariyalur District.

Amount

Clearing and Removing of Heavy Jungle clearing away from the site and levelling the site etc. complete.

Earthwork excavation for foundation in all soils except hard rock requiring blasting to a full depth with an initial lead of 10m and lift of 2m in hard stiff clay,stiff black cotton,hard red earth mixed with small size boulders etc.,complete.

Supplying and Filling in foundation and basement with river sand in layers of 150mm thickness well watered rammed and consolidated complying with relevant standard specification.

Supplying and filling in foundation and basement excavated earth soil in layers not more than 16cm thick well rammed watered, consolidated and compacted etc., complete.

Cement Concrete 1:5:10(One Cement five sand ten aggregates) using 40mm gauge HBG jelly inclusive of shoring strutting and baling out water where ever necessary ramming curing etc., complete in respects complying with relevant standard specification and as directed by the Department Officers.

Damp Proof in cement mortar 1:4, (one cement and four sand) 20mm thick mixed with Impermo powder 2% by weight of cement ect., complete.

Brickwork in Cement Mortar 1:5 (One cement and five sand) using IInd class chamber burnt bricks of size 9"x4½"x3" including cost and conveyance of all materials and labour charges and all other incidental charges etc.,complete complying with standard specification.

Upto For Basement

In Ground Floor

Brick partition wall in Cement Mortar 1:3 (One cement and three sand) 11.40 cum. thickness using II class chamber burnt bricks of 9” x 4 ½” x 3” including both side plastering with CM 1:5, 12mm thick and using hoop iron with reinforcement if found necessary etc. complete.

In Ground Floor

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Upto Basement

In Ground Floor

Supplying fabrication and placing in position of MS (or) Rts bars for all RCC works including cutting bending placing and cost of binding wire etc.,complete.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such ascolumn footings, column pedestals, plinth beams, grade beams,staircase steps, etc.., requiring nominal strutting using mildsteel sheets of size 90cm x 60cm and 10 BG stiffened with weldedmild steel angles of size 25mm x 25mm x 3 mm for boarding, laidover silver oak joists of size 10cm x 6.5cm spaced at about 75cmcentre to centre or at suitable intervals etc. complete in all floorscomplying with standard specifcation..

Column Footing and Plinth Beam

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfacesas in all floors with all cross bracings using Mild Steelsheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steelangle of size 25mm x 25mm x 3 mm for boarding laid over silver oakjoists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centreand supported by casurina props of 10cm to 13 cm dia spaced at notmore than 75 cm centre to centre etc. complete complying with thestandard specificaiton.

Plain Surfaces Beams, Roof slab

Centering for Sunshade and Rectangular Column

Special ceiling plastering for R.C.C slab beam and sunshades with cement mortar 1:3 ,10mm thick including tacking finishing neatly, cost and conveyance of all materials and all labour charges,curing etc., complete complying with standard specifications.

Plastering with Cement Mortar 1:5 (One cement and five sand),12mm thick including cost and conveyance of all materials and all labour charges,curing etc., complete complying with standard specifications.

Weathering course concrete with broken jelly 20mm size and pure slaked lime over RCC roof slab,the proportion being 32:12.5 for required depth of 80mm for giving required slope and thickness of roof on required ,well beaten with wooden beater etc.,complete.

Finishing the top of roof with one course of machine pressed tiles of size 23cmx23cmx20mm of approved quality laid in 1:3,12mm thick mixed with water proofing compound 2% by weight of cement used etc., complete with standard specification

Supply and fixing Window M.S.Grill of approved design including welding,transporatation and one coat of primer etc., complete

Supplying and fixing Teak Wood Frames for DOORS, WINDOWS, VENTILATORS and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc., complete in all floors.

Upto 2m in Length

2m to 3m in Length

Supply and fixing in position of UPVC sliding door of any size .The outer frame will be 62x38x2mm 21.17Kg/m and the louvers with moving arrangements will be made with Aluminium,channel of size 60x30x4mm @ 1.27kg/m with necessary glass pans for louvers 4mm thick Alulminium clips 19.05x17.27x11.05x0.075mm @0.169kg/m including all materials,labour and power consumption charges required fro fabrication if necessary chipping dismantling making hole sing RCC columns,beams or masonary whereever necessary with power drill to the extent required and make good to the original conditions.

Supply and fixing in position of UPVC ventilator of any size .The outer frame will be 62x38x2mm 21.17Kg/m and the louvers with moving arrangements will be made with Aluminium,channel of size 60x30x4mm @ 1.27kg/m with necessary glass pans for louvers 4mm thick Alulminium clips 19.05x17.27x11.05x0.075mm @0.169kg/m including all materials,labour and power consumption charges required fro fabrication if necessary chipping dismantling making hole sing RCC columns,beams or masonary whereever necessary with power drill to the extent required and make good to the original conditions.

Supplying, fabrication and fixing of 30mm thick both side pre laminated WPC door shutter with frame of required size 0.75m x 2.00m & 0.90 x 2.00m including necessary brass furniture fittings such as 125mm x 25mm brass hinges-3Nos , 200mm x 12mm brass tower bolt - 1No, 150mm x 12mm brass tower bolt - 2Nos,150mm brass handle - 2Nos, cylindrical lock - 1No, T.W lippings around the shutter etc., including cost, conveyance of all materials and labour charge for fixing complying with standard specification.

Flooring with Anti Skid ceramic tiles of approved quality, colour design and of size 30cmx30cm laid in cement mortar 1:3 (One Cement and Three Sand) 20mm thick including pointing the joints with same colour cement to the full depth of the tiles including cost and conveyance of all materials and labour etc. complete.

Dadooing the side walls with glazed wall tiles of approved quality colour, design and of size 30cm x 45cm in cement mortar 1:2 - 10mm thick and painting with white cement including finishing the joint and polishing the tiles surface glassy etc. complete

Supplying and fixing in position best quality approved make, colour glazed Earthenware wash hand basin oval shape of size 550x400mm in granite table top including cost of 15mm brass chromium plated pillar cock 32mm dia CP waste coupling with rubber and chain, 15mm dia CP angle valve, 15mm dia brass nipple, 15mm dia Nylon connections including fixing the wash in position with a pair of M.S. angle 50x50x6mm etc. Complete as per standard specification.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing in position Indian water closet of size 580x440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap conforming to IS 2556-Part XII with 10 lit capacity PVC flush tank and internal fittings with sand cushion and forming, flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to case iron soil pipes by dismantling brick masonary, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without quality with 'P' trap or 'S' trap conforming to IS:2556 leakage etc., complete complying with standard specifications.

Supplying and fixing in position Indian make white glazed earthernware Magnum urinal of ISI standard and best approved colour urinal of best approved quality with G.I.pipe connection of 32mm, bell mouthed, waste Pipe, 15mm. dia G.M. Gate value bring the urinal to the wall in position with necessary T.W.Plugs, clamps, shellac etc., including dismantling masonry if necessary and readoing the same to original condition fixing the 15mm. dia G.I.pipe and wheel valve. Painting the pipe with two coats of approved paint over one coat of primer and checked without any breakage complete complying with standard specification.

Supplying and fixing 50mm thick (both side polished) marble slabs for shelves (4 tier) with neat finishing. The rate inclusive of cost of slab and labour charges for fixing etc., complete as directed by the departmental officer.

Supplying and fixing of CP screw down tap heavy type 15mm dia including testing for leakage etc., complete complying with standard specification.

Supply and fixing of Health faucet of approved quality and make including fixing in position etc., complete. (Local Market rate)

Supply and fixing 4” dia PVC Nahini trap of size with C.P. Gratings 100mm x 75mm of approved quality etc. complete as directed by the Corporation Officers.

Supplying, laying and jointing of following size of CPVC pipes of approved make and ISI quality including fixing CPVC specials but excluding cost of CPVC specials,cutting, threading of pipes concealing the pipes into wall with necessary clamps and nails , dismantling the wall, laying pipes and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary etc. complete as directed by the Corporation Officers.

25mm dia (1") CPVC pipe

20mm dia (3/4") CPVC pipe

Supplying, laying and jointing of following size of PVC pipes of approved make and ISI quality including fixing PVC specials but excluding cost of PVC specials,cutting, threading of pipes concealing the pipes into wall with necessary clamps and nails , dismantling the wall, laying pipes and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary etc. complete as directed by the Corporation Officers.

40mm dia (1½") PVC pipe

50mm dia (2") PVC pipe

Supplying and fixing of 75mm dia P.V.C pipes 6Kg/SqCm of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs, PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.Above ground level upto 4m height.

Supplying and fixing of 110mm dia P.V.C pipes 6Kg/SqCm for Sanitory line of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs, PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.Above ground level upto 4m height.

Supply & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes etc., complete.

Supply and fixing the following GI and PVC pipes and CPVC specials for pipe connection arrangements for inlet outlet sour and overflow etc., including cost of pipes specials valve labour charge fro lifting aligning ,cutting,threading,fixing and painting of GI pipe with two coats of approved quality enamel paint etc.,complete as detailed below.

25 mm Dia CPVC Elbow

25 mm Dia CPVC Tee

25 mm Dia CPVC coupling

25 mm Dia CPVC Union

20mm Dia CPVC Elbow

20mm dia CPVC Tee

20mm dia CPVC Union

20 & 15mm dia CPVC elbow

75mm dia PVC Plain elbow

75mm dia PVC Door Elbow

75mm dia PVC Door Tee

75mm dia PVC Tee

110mm dia PVC Door Tee

110mm dia PVC Bend

110mm dia PVC Cowl

Supplying and fixing GM gate values, GI fittings, pvc specials of various sizes of approved quality and ISI band as per standard specification

20mm dia Brass ball valve

Construction of manhole chamber of size 600x600mmx1100mm (above GL 200mm Below GL 900mm) to total height of 1100mm (ID) 200mm above ground level 900mm below ground level with a base concrete of 100mm thick 1:5:10 over a sand cushion of 100mm thick. The chamber should be constructed in brick masonry 230mm thick in CM 1:5 with stock bricks of size 9"x41/2"x3". The inner side of chamber plastrering in cm 1:5, 12mm thock, the outer chamber of wall to depth of 300mm plastered in cn 1:5, 12mm thick. The Chaber top covered with SRF cover slap 100mm thick. The rate is includuing the cost of material,Labour etc, complete.xincluding all works of earthwork,CC 1:5,10, 200mm thick,Brickwork, plastering in CM 1:5,12mm thick etc., complete

Providing Pathway hand rails using 304 grade 16 SWG SS pipes 40mm dia as verticals to height spaced at 1m centre with top railing 50mm dia and 25 mm dia pipe intermediate rigidly fixed with spacing of 0.30m centre to centre vertically in the existing concrete/brick wall structure and properly fixed including all materials and labour charges polishing transport charges etc., complete

Painting two coats with Plastic Emulsion paint of approved quality and colour including one coat of emulsion primer over new wall surfaces including cleaning and preparing the surface, scaffolding etc., complete.

Painting two coats with Elesto metric acrylic water proof Exterior Emulsion paint ( Dr.Fixit or equivalent) over one coat of primer (Prime seal of Dr. Fixit or equivalent) after cleaning the surface over old wall surfaces including scaffolding etc., complete. as per standered specification.

Painting two coats with Ready mixed synthetic enamal paint of approved quality and colour over new Iron surfaces including prepare the surfaces, cost of brushes and all materials, scaffolding etc., complete.

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying interlocking Rubber Moulded Hydraulic Pressed Paver Block M40 grade 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 50mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers, sweeping tranporting loading unloading of laying paver block as per standard specification,. Natural grey colour

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 300mmx450mmx125mm in Cement Concrete 1:2:4 (One cement, Two sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Labour Charges for finishing Kodungai (0.60x0.60) as per standard architectural drawing

Lobour charger for viyazhapuri or parapet (0.35mx0.45m)

Labour charges for finishing columns upto 5m height 0.50 diameter

supply of cement for the Architectural work

Supply of river sand for the Architectural work

Supply of II class ground Moulded Chamber bricks of size 9"x43/8"x23/4" for the Architectural work

Supply and Fixing of Aluminium 10" Dye cast Tamil Letters approved colour.The colour treatment process is achieved with MRF colour coat and the kiln for the heat treatment process etc.,complete.

Tamil Stainless Steel Letters 10"

English Stainless steel Letters 10"

Manufacturing, Supplying and Fixing of Stainless Steel Gate for Entrance using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia+B107 Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and erecting in position of following liters capacity industrial model reverse osmosis Water-Cum-Purifier to deliver potable water with world health organisation (WHO) Standards with following accessories. 1)Feed pump - 0.5 HP, 2)1354 Vessal - 1 no, 3)1'' MPV Valve - 1No, 4)Media pubble and fine sand and activated carbon filling) - 3 set, 5)Pressure Gauge- 2 Nos., 6)Flow meter- 2 no. 7)Micro Filter-2 Nos 8)Micro Filter Vessal-2 No, 9)Pipe Line- 3/4'' - 1 set, 10)Astro Panel- 1 No, 11)40/40 vessal -1 No, 12)40/40 Membrane - 1 No, 13)HP pump- 1 No, swith Housing -1 no, Low pressure switch-1 no, level switch- 1 no and necessary CPVC pipe and fittings. The System shall be provide with two panel control system with necessary stainless valves and fittings all civil works, wherever necessary to install the system in position and intact

Supply and Installing the Multi play (code no.VMP-03) having single tower, 1 LLDPE Roof 1 LLDPE Spiral Slide 1 LLDPE Multicolored Slide 1 Ladder Safety Grills Etc of 32mm and 25mm dia MS Pipes including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Multi play (code no.VMP-10) having single tower, 1 LLDPE Roof 1 LLDPE Spiral Slide 1 LLDPE Multicolored Slide 1 Ladder Safety Grills Etc of 32mm and 25mm dia MS Pipes including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Multi play (code no.VMP-18) having FRP Wave Slide 1 Ladder Grills Etc of 32mm and 25mm dia MS Pipes including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Jeep Ride On (code no.Vsp - 64) with LLDPE height of 15" and Spring lenth of 10" including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supplying of Dustbin-Penguin (VSDP-89) having FRP Penguin shape for a height of 3 feet etc complete with standard specification.

Supplying of Dustbin-Rabbit (VSDP-89) having FRP Rabbit shape for a height of 3 feet etc complete with standard specification.

Supplying of Dustbin-Elephant (VSDP-89) having FRP Elephant shape for a height of 3 feet etc complete with standard specification.

Supply and Installing the Junior Slide (VS-27) having Polyurethane Slide 8.5ft long with Ladder vertical height of 4ft including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Double Slide (VS-29) having Polyurethane Slide 8.5ft long with Ladder vertical height of 4ft including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Merry Go Round (VS-36) having of 60mm,32mm and 25mm dia MS Pipes for Outer diameter size of 5 feet with 6 nos of LLDPE seats with sealed Bearing including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Arch Swing (VS-3) having of 60mm dia pipes for main frame with Top Sealed Bearing and 2 nos of FRP Seats joined with Stainless Steel Chain for a length of 10 ft and height of 7 ft including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Arch Swing (VS-6) having of 60mm dia pipes for main frame with Top Sealed Bearing and 2 nos of FRP Chairs Seats joined with Stainless Steel Chain for a length of 10 ft and height of 7 ft including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Circle Swing (VS-8) having of 75mm dia pipes for main frame, 32mm and 25mm dia pipes for circular portion, 50mmx25mm square tube pipes for Seating and foot rest portions with Heavy Duty Bearing system for a length of 6 ft and height of 5 ft including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the Triple Seesaw (VS-21) having of 60mm and 25mm dia MS Pipes for a Top length of 7 ft, Stand length of 9ft and height of 2ft with 4 nos of LLDPE Special seats including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Supply and Installing the FRP Standard Slide (VS-22) having Polyurethane Slide 8.5ft long with Ladder vertical height of 4ft including all equipments and including Earthwork excavation,Filling with river sand,Cement Concrete 1:2:4 and Plastering with CM 1:3 and labour charges for fixing the playing materials etc complete with standard specification.

Levelling the site and Preparation of surface for fixing of Playing Materials.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade\in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator)

Supply and Run of 2 of 2.5 sq.mm.(56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and laying of 3 -1/2 x 35 Sqmm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of brass cable gland for 3 1/2 x 35 sqmm PVC LTUG aluminium armourd cable with earth connection

Supply and providing cable end termination of 3 1/2 x 35sqmm PVC LTUG aluminium armoured cable necessary aluminum cable sockets by crimping etc with eelctrical connection complete.

Supply and fixing of horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP43 protection with 40A 4 pole MCB isolator as incoming and 12 Nos 6A to 32 A SP MCB as outgoing inflush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB`s should be with the ISI mark.

Supply and fixing of TNEB meter board suitable for 32A three phase service connection with 3 Nos. 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 600mm x 450mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Four Pole RCD / RCCB (Higher End) with suitable necessary connection

Earthing as per standard with an earth electrode of 2 meter class B GI pipe of dia not less than 32mm complete with necessary masnory work

Supply and installation of 22W 4 feet LED tube light fitting with its electrical connection etc., complete.

Supply and installation of 18W 2 feet LED mirror light fitting with its electrical connection etc., complete.

Supply and installation of 15W LED Bulkhead fitting with its electrical connection etc., complete.

Supply and fixing of 8" Brisk air ventillation exhaust fan with its electrical connection to make good condition.

Supply and laying of 3 -1/2 x 35 Sqmm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of brass cable gland for 3 1/2 x 35 sqmm PVC LTUG aluminium armourd cable with earth connection

Supply and providing cable end termination of 3 1/2 x 35sqmm PVC LTUG aluminium armoured cable necessary aluminum cable sockets by crimping etc with eelctrical connection complete.

Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 4C X 16 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 4C x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and installation of Street light feeder pillar with 63A MCB incomer and 8 Nos 32A DP MCB with sheet metal enclosure - Weather proof type with inbuilt timer control All compontents covered with Hylem sheet of 12mm thickness with necessary bolts and nuts and with earth connection complete.

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 1 of No.8 SWG GI wire for earth connection. (SD-74)

GST at 18%

J C ENGINEERING CONSTRUCTION COMPANY (BID ID -1257431)