Special Repair to JCOs MD Accn Bldg No NP-12 (08 x Qtrs) of 223 ABOD Suranussi under GE Kapurthala

Amount

Demolition of brick work built in cement mortar including all quoins arches etc

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick above or below ground level.

Taking down cement or cement lime plaster of any description from walls, including raking out joints hacking for keys srubbing down with water etc

Taking down chowkats or frames with Shutters (without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each and removing from site.

All as per Item No 4 above but area exc 1.50 Sqm but n.exc 4.00 Sqm complete all as specified.

Taking down shutter only of any desription of size n. exc 1 sqm

Taking down shutter only of any desription of size exc 1 sqm and n.exc 2sqm

Ditto all as per item No 7 above but refixing in the same opening complete all as specified.

M&L for brick works built in cement mortar (1:6) using sub class ‘B’ bricks (old size) straight or curved on plan exc. 6m mean radius complete all as specified.

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete wall surfaces and surface finished even & smooth without using extra cement complete.

M&L for rendering 15 mm thick in CM 1:4 on brick or concrete wall surfaces and surface finished even & smooth without using extra cement complete.

M & L for 5 mm thick plaster in cement mortar 1:3 finished even and smooth without using extra cement to ceiling/chajja’s complete all as specified.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165) complete all as specified

M&L for 35 mm thick , factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated.

S&F for 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete fixed in position.

M&L for 35mm thick IInd class HW glazed /gauged shutters open rebatd and prepared to receive glass /gauge etc without sashbars edges of framing plain or chamfered or rounded fitted with cut and mitred beads for securing glass/gauge etc all as specified in SSR Part I section 8 clause 8.24 (a) complete as specified & directed.

S&F solid PVC door frame of size 50mmX 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing given in SSR complete.

S&F 30mm thick factory made PVC door shutter solid panel consisting of frame made out of MS tubes for top & bottom rails .Ms frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colourPVC sheet for top rail , lock rail &bottom rail on either side & as gap insert for top rail & bottom rail . Panelling of plain of plain colur PVC sheet to be fitted in the MS frame welded/sealed to stiles & rails with suitable PVC sheet beading and joined together with solvent cement ,etc all as specified and shown on drawings.

Supply & Fixing for steel windows made up from MS sheet of 1.25 mm thick box type (primer coated) ERW hollow 'P' section of size 60mm x 25mm single rebate comprises of skeleton shutter ERW sec 50 x 20 mm & 1mm thick and openable leaf consisting two nos sash bar of T section 20x3mm complete welded to frame including cutting holes and making good dismanteled portion in cement concrete (1:2:4) type B-I four nos for each window including following fitting welded to shutter complete all as specified and as directed by Engineer-in-Charge :- (i) Hold fast 150mm long 12 mm x 3mm made to shape - 04 Nos each window. (ii) Handle of Z Section 20 x 25 mm, 100mm long 01 Nos each leaf. (iii) MS tower bolt 150 mm long-02 Nos each leaf. (iv) Z Section 20 x 25mm, 100 mm stopper - 01 Nos per leaf (v) Cleat 55 mm long of hollow square 15x20x63mm welded to hinges - 01 Nos per leaf. (vi) MS Box type hinges of size 75 X 12 mm - 02 Nos per leaf. (vii) MS Guard bars square 12mm dia @10 cm c/c with GI frame fixed to window frame. (viii) Fabrication and fixing Note : glass pan shall be measured and paid for separately.

Ditto all as per item No 19 above but with Gauged shutter, Note : WIRE CLOTH shall be measured and paid for separately

S&F 300mm size mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12mm dia including a minimum of six nut and bolts ,four on bolt plate and two on stapple plate complete all as specified

S&F mild steel barrel tower bolt 200mm size stove enamelled black with bright bolt etc all as specified

S&F 150 mm size mild steel pressed handle stove enamelled black and fixed complete all as specified and as directed by engineer-in-charge.

S&F 100 mm size mild steel butt hinges medium weight cold rolled complete all as specified and as directed by engineer-in-charge.

S&F floor door stopper aluminiumalloy body and tounge 140mm anodised with hard drawn steel spring etc.

S&F 300mm size mild steel rat rail rod pattern spring including roller and roller plate complete

S&F in repair block board 19mm thick commercial type exterior grade fixed to timber frame work

S&F in repair pre laminated decorative block board 25mm thick prelminated on both faces etc fixed to timber frame work complete all as specified

S&F in repair galvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm complete all as specified

Ditto as per item No 29 above but fixed in repair complete all as specified

Hacking out broken glass from steel frame including driling out old glazing etc

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm each panes complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed or bedding layer in CM 1:6 complete all as specified

M&L for glazed ceramic tiles coloured of size 300mm x 200mm & 7mm thick on vertical surfaces such as in skirting, dado etc over and including 10mm thick backing coat in cm 1:4 complete all as specified.

M & L for Complete removal of existing treatment and applying two coats of oil bound distemper over a coat of alkali primer complete all as specified and directed

S&F in repair Vitreous china ware water closet Orissa pattern including connecting to trap and to flushing pipe anti Syphonage pipe etc complete, fixed of size 580mm X 440mm complete all as specified. Make: Hindware / Cera / Parryware.

S&F in repair PVC low level flushing cistern of cap 10 ltrs including long bend PVC flush pipe for squatting pan fixed to wall ISI marked completed with brackets and accessories.

S& F in repair vitreous china wash hand basin flat back 550X400mm with and including fixing bracket,pvc waste coupling and waste pipe,cp pillar tap etc all as specified and directed by engineer-in-charge.

S&F in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed (two brackets per 1.5 M length and 08 Nos roller per 1.RM)

Dismantling brick tile or terracing tile laid in single layer on roof

Demolition of mud in roofs ,any thickness including plastering and leeping (weather full thickness removed or part there of).

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for.

M/L for PCC 1:5:10 type E2 with using 40 mm graded stone aggrgate as in filling for sunken floor and like works

Supply only Integral waterproofing compound

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces.

M & L for water proofing treatement with APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application complete all as specified

M&L for 50mm average consolidated thickness pcc 1:3:6 type C2 with using 20mm graded stone aggregate as in padding on flat roofs etc all as specified and directed.

M/L for 40mm thick brick tiles laid on cement & sand mortar and joints grouted flush incement mortar (1:3) mixed with 5% of crude oil by weight of cement and pointed flush in CM 1:3 complete all as specified.

All as per item 50 above but except tiles.

Dismantling water tanks of any description exc 250 and n.exc 500 ltr capacity and removing to store complete all as specified.

Taking down GI tubing and connections with all fittings 15 mm bore

Ditto all as per item 53 above but 20mm bore

S&F 15 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc

ditto all as per item 55 above but fixing only

S&F 20 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc

Ditto all as per item 57 above but fixing only

S&F in repair CP shower rose 15mm sizefixed to iron pipe

S&F pvc connection 15mm size with PTMT nuts of length 450mm

S&F in repair 15mm brass bib tap crutch or butterfly handle screwed for iron pipe etc

S&F in repair 15mm size brass stop valves with crutch or butterfly handles high pressure screwed both ends for iron pipe

S&F in repair 20mm size stop valves PTMT high pressure screwed for iron pipe

Ditto all as per item No 63 above but concealed type

S&F in repair towel rail 600mm long of PTMT incl cp brass screws etc

S&F Rotational moulded polythene water storage tanks double layer (cylinder each vertical with closed top) of capacity 500 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1 Make : Sintex / Frontier / Polycon

M&L for preparing surfaces of new plastered walls and applying two coats of oil bound distemper over a coat of alkali primer complete all as specified.

M&L for preparing surfaces of new plastered walls and applying two coats of cement base paint over a coat of alkali primer complete all as specified.

Ditto all as per item no 68 above but applying one coat on old treated surface

M&L for three coats of white wash on old surface including preparation of surface

M&L for preparation of new plastered surfaces of any description not otherwise described and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for two coats synthetic enamel paint on new wooden surface over 10 cm width or girth over a coat pink primer complete all as specified

Ditto all as per item No 72 above but one coat on old treated surface.

M & L for 2 coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces complete all as specified

Ditto all as per item No 74 above but one coat on old treated surface

M&L for Providing, cement concrete type 1:2:4, type B-1 using 20 mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges parapets copings, bed plates, etc

M&L for PCC 25mm thick 1:2:4 type B1 using 20 mm graded stone agg as in levelling course.

M&L for 75 mm thick PCC 1:3:6 type C2 as in plinth protection with using 40mm graded stone aggregate etc all as specified.

M&L for 40mm thick PCC 1:2:4 type B1 as in flooring including finishing the surface even and smooth with using extra cement.

Supply only glass dividing strip 38mm wide and fixed in position 3mm thick Note:- Labour for fixing is included in item of PCC).

S&F in repair PVC SWR pipe 110 mm dia single socketed in any length with rubber ring joints fixed to walls etc all as specified

Ditto all as per item No 81 above but laid in trenches

Ditto all as per item No 81 above but 75mm dia

Ditto all as per item No 83 above but laid in trenches

S&F in repair 75mm bore size PVC (SWR) floor trap plain with grating including jointing with waste pipe with cement solvent etc all as specified

S&F 110 mm dia PVC SWR type bends any radius complete all as specified

Ditto all as per item No 86 above but 75mm dia

S&f 100 mm dia stack clamp made out of 25x4mm Flat iron etc all as specified

S&f 75mm dia stack clamp made out of 25x4mm Flat iron etc all as specified

Cutting grooves of size 75mm wide and 65mm deep in brick parapet wall for inserting APP membrane and making good the disturbed portion in CM (1:3) complete all as specified.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, including waste coupling and waste pipe

S&F in repairs Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-110gms)

M&L for 20-25 mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, over and including 20 mm thick screed or bedding layer in CM 1:6 complete all as specified.

All as per item No 93 above but as in skirting over 10mm thick rendering in CM 1:4

Taking down carefully aluminum point wiring on TW Batten/in conduit / with conduit (light/Fan/socket or power) complete and making good the disturbed surfaces of wall/ceiling etc including taking down fittings such as switches, ceiling roses, pendants, Regulators, sockets, light fittings etc and removing material from site except tube light fittings, fans etc which shall be re-used in work complete all as directed .

Material and Labour for Concealed point wiring complete with 1.5 Sq.mm (nominal area) FR PVC insulated multi stranded copper conductor in and including heavy duty PVC conduit (wall thickness 1.6 mm) including fittings & accessories, with MS concealed terminal boxes with 3mm thick laminated bakelite ( Hylum/Anchor) sheet top cover for mounting switch, socket etc for one light/fan/bell point controlled by one switch and regulator with PVC cable copper conductor including 1.5 Sqmm solid copper conductor with green FR PVC insulation earth common earth dolly, complete all as specified . Make :Finolex/Havell's/Plaza/Indo Asian

All as per ser item 96 above but for 3 pin socket out let 5 Amps on same board

All as per ser item 96 above but for 3 pin socket out let 5 Amps on independent board

All as per srl item No 96 above but for 3 pin socket outlet 15 Amps with 2.5 Sqmm stranded copper conductor PVC unsheathed cable independent including PVC cable copper conductor 2.5 Sqmm with green insulator as earth wire with cast iron/pressed steel terminal box all as specified.

All as per item No 96 above but one light point controlled by two way switches

Supply and fixing switch piano flush type 5 Amp single pole one way. Make : Havells/SSK/Leader

Supply and fixing switch piano flush type 15 Amp single pole one way. Make : Havells/SSK/Leader

Supply and fixing switch piano 5 Amp flush type single pole two way. Make : Havells/SSK/Leader

Supply and fixing socket outlet 5 pin 5 Amps flush type multi purpose. Make : Havells/SSK/Leader

Supply and fixing socket outlet multipurpose 2 in one, 6 pin 15Amps flush type. Make : Havells/SSK/Leader

Supply and fixing lamp holder with PVC insulated body fixed plastic laminated sheet cover shape 3mm thick suitable for batten fitting including 01 No. of LED 1 x 15 Watt, 230 volts, suitable for 230 Volt AC complete all as specified.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

All as per Srl item No 107 here in before but fixing old serviceable fittings with rod obtained from sl item No. 95 shall be reused after minor repair (if reqd).

Supply and fixing ceiling rose surface bakelite 65 x 50mm three terminals complete. Make : Havells/SSK/Leader

Supply and fixing bell push flush type 5 Amps complete. Make : Havells/SSK/Leader

Supply and Fixing fan regulator electronic step type and making connection. Make : Rallison/Leader/Bajaj

Supply and fixing sheet steel enclosure with double door, detachable gland plates flush/surface mounting for MCB’s fitted with bus bar, earth bar and neutral link 8 ways SPN 240 V Make : Standard/Havells/Ship

Supply and fixing sheet steel metal enclosure (DB) triple pole and neutral 4 way 415 ,Volt with 200 amps rated bus bar Make : Standard/Havells/Ship

Supply and fixing Isolator SPN 240V, 40 Amp. Make : Standard/Ship/Havell’s.

Supply and fixing Isolator SP 6 to 40 Amps 240 Volts. Make : Standard/Ship/Havell’s.

Supply and fixing Isolater 63 Amps TPN 415 Volts. Make : Standard/Ship/Havell’s.

Supply and fixing call bell single phase 240 volt

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

M&L for submain wiring with two runs of single 4 sqmm PVC insulated unsheathed multistranded 1100 vols grade with copper conductor drawn through and including in steel conduit medium grade ISI marked and its accessories including one run of single core 4 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth contuinity conductor along with the wiring and connected from DB to DB/ main board completeall as specified and as correct.

Supply and fixing in replacement of cable in trenches / on pole/wall in protection pipe cable XLPE insulated screened armoured PVC bedded 1100 volts grade 25 Sqmm 4 core complete all as specified. Make :-Finolex/Havells/Plaza/Polycab

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth ,and getting out in soft/loose sil for laying if GI pipe etc.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Material and Labour for Sand filling as sand cushioning for cable laid in trenches, Note:- The 18mm thickness after punning down shall be measured.

Supply and fix common burnt clay building bricks Sub class B designation 75

Supply and fixing Sheet Metal Enclosure (Energy Meter Box) suitable for housing 02 Nos single phase energy meters 01 No. Make : Standard/Havells/Ship

Supply and fix cock, stop brass, chromium plated screwed down for size 15 mm dia pipe.

Supply and fix cock,bib,brass chromium plated screwed down for size 15 mm dia pipe.

M & L for PVC Connection pipe (Copper) chromium plated 8 mm dia both end threaded incl brass coupling bolt cone washer complete lenghth of pipe not leass than 450 mm suitable for Hot/cold waer system complete all as specified .

Supply and fixing for water heater storage type (Geyser) Vertical type with inner container of capacity 25Ltrs, electrically operated,AC230 volts, including 04 nos of hold fashner nuts of suitable size fixed in brick wall complete all as specified and directed.

Material and Labour for replacement of earthing with galvanized iron earth plate electrode 600mm x 600mm & 6mm thick buried directly in ground vertically in a earth pit not less than 2.25mtr below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to GI earth wire 4mm dia by means of GI bolts, nuts, check nuts and washers (earth plate covered with alternate layers of charcoal dust and common salt 15cm thick), GI earth wire protected by GI pipe light grade 15 mm dia upto switch board and connected to main switch board including provision of GI pipe 20 mm dia light grade watering pipe with funnel and wire mesh, all as shown in Electrical Plate No. 3 of SSR Part-I, including PCC chamber (1:3:6) using 20mm graded stone aggregate and CI cover and frame including all necessary excavation and earth work and taking out old earthing complete all as specified and directed.

DUGGAL CONSTRUCTION CO