COMPREHENSIVE MAINT AND REPAIR TO OFFICER MD ACCN OF TARAPORE ENCLAVE UNDER GE (SOUTH) DELHI CANTT

Taking down (Door) chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete.

M&L for factory made pressed steel frames for doors made out of 1.25mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12mm bar thresh hold etc. complete , of frame size 125mm x 60mm, including one shop coat of red oxide zinc chrome primer complete all as specified.

S&F 300mm aluminium, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified. (ISI Mark)

S&F in repair for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm both side Prelam PVC sheet used instead of plain colour PVC Sheet and edge will be painted to match with prelam sheet. reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified and as directed.

S&F Factory made solid panel PVC Moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Clause No. 8.B.1 to 8.B.10 and drawing on page No. 156 & 157 of MES SSR-2010 Part-II complete all as specified.

M&L for complete removal of existing treatment under (OBD/Oil paint/ white wash etc) by scrapping with mechanical wall sander on wall/ceiling (having mechanical vacuum mechanism) having RPM not less than1500, sending pad of 80 grit having dia of 7"/9" to make the surface free from dust, loose paint , removal of nails etc and filling cracks/ holes and windows /doors jams by putty & repairs in good shape by skilled labour complete all as specified and directed.

M&L for cement based putty @ 1KG (undiluted) per square meter of average thickness 1 mm over the plastered/Old painted wall /ceiling surcafes to make the surface free from dust etc, by skilled labor as per following steps :- Step 1 :- Mix the putty powder by adding water as per manufacturer instructions and mix it with wall mixture with the mixing capacity of minimum 2.5 kg putty per minute Step 2 :- Applying the first coat of prepared mixture with the help of fully automatic airless spray machine of putty application having flow speed of maximum 6 liters per minute with a maximum pressure of 3300 PSI. Step 3 :- Allow 6-8 Hrs time to dry the putty surface.

M&L for applying two coat of oil bound distemper on wall/ceiling using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. Make Asian or equivalent.

M&L for applying two coat of oil bound distemper on wall/ceiling on new plastered surfaces using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 Mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by pain manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. Make Asian or equivalent

M&L for preparation of old plastered surfaces of wall / ceiling applying two coats of white wash including scaffolding arrangement, trestles, ladders complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel of any description over 10cm width or grith and applying one coat of synthetic enamel paint, complete all as specified and as directed.

S&F in repairs, Wall mixing valve 15mm dia Hot & cold CP brass fancy with L-bend including joints to steel pipe or unions , including fittings for, complete all as specified and as directed.

S&F in repairs of plastic WC seat cover white / off white closed pattern with flat bottom end cover and mild steel CP hinging device complete all as specified and as directed.

S&F in repairs, CP brass health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe, complete all as specified and as directed.

S&F in repairs, brass spindles with knob (Each splindle having 01 x CP Knob fitted with screw) Chromium plated suitable for existing concealed stop valves/Bib tap/Hot & Cold mixer valve (for WHB/Sink/Wall) all as per sample, complete all as specified and as directed.

S&F in repairs, PVC valveless, syphonic action type, flushing cistern of 10 Ltr capacity, low level, white, with inlet, ball valve, float and handle, one number PVC connection, with brass nuts including PVC 'L' bedn pipe fitted to WC and brackets to fix the flushing cistern with wall, complete all as specified and as directed.

S&F in repairs, PVC waste pipe 32mm bore, 65cm long plain/ corrugated including suitable adopter, complete all as specified and as directed.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified

S&F steel peg set colour coated of six as per sample in repairs complete all as specified.

S&F stainless steel grating dome 100/125 mm dia of best quality, complete all as specified and as directed.

S&F in repairs, Brass chromium plated shower rose 125mm size with arm, complete all as specified and as directed.

S&F in repairs Sinks with drainage board made of 1mm thick stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including PVC waste pipe 32 mm bore, 65 cm long complete.

S&F in repair 15 mm angle valve / stop cock chromium plated, cast copper alloy screwed down high pressure fancy type, chromium plated with long shank and cup (concealed type) screwed for both ends for iron or for unions complete all as specified and as directed.

S&F in repair Bib taps long body 15mm bore, chromium plated cast copper alloy, fancy screwed both ends complete all as specified and as directed.

S&F PVC connection 15mm size with brass nut of length 450mm for hot water pipe,complete all as specified and as directed.

S&F toilet paper holder of vitreous china fixed to wall with chromium plated (CP) brass screws, complete all as specified and as directed.

S&F in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repairs 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supplying and laying of CPVC 20 mm dia pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all brass fitting (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) including taking down of existing GI steel tubing complete all as specified and as directed.

M&L for steel water tubing of nominal bore 32mm medium grade galvanised with all fittings including short lengths, fixed to walls or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) including taking down of existing GI steel tubing complete all as specified and as directed.

S&F in repair deco door seal bottom brush dust stopper strip aluminium plate with nylon brush for cover the bottom door gaps between 20-25mm including fixing with steel screws etc, complete all as specified and as directed.

S&F 18 mm thick LEAD FREE WPC BOARD of Single side rigid laminated of approved colour and other side plain WPC fixed with screws and solvent cement/adhesive to make kitchen/bed rooms cabinet frame (3 Inch throw out as frame), cabinet sides top and bottom and shelves inside the cabinets complete and cupboard shutter will be fixed with piano hinges as per manufacture’s specification complete all as specified and directed by Engr-in-Charge. Note :- Density not less than 650 kg/cbm having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compissi

ve of 50 N/mm2, Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws & all necessary fittings and fixtures hasp and staple, knobs etc complete including dismantling of existing of board any type all as specified and directed. (a) Pattern & design of WPC board to be decided by GE. (b) Items like, magnetic Catcher, cupboard 100mm SS handle, and CP Clip/continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap (when open) is 30mm, Haps & Staple deemed to be included in the quoted rate.

S&F 75 mm long L Bihari concealed type hydraulic hinges including stainless screw complete all as specified and directed.

S&F Modular Cabinet Kitchen accessories of Stainless Steel grade-304, 6mm size rod thickness including :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all spd and directed by Engr in charge

S&F stainless steel AISI 304 grade handle of size 75 mm long, etc. complete all as specified and directed.

S&F Chromium plated 50mm C-profile continuous, uninterrupted handle fixed with stainless steel screw, complete all as specified and directed.

S&F in repair PVC water storage tanks 250 litres capacity (Rectangular with closed top) and fixed in position including PVC float valve 15mm bore with ball & aluminum rod and fly nut complete, screwd for iron pipe inclusing dismantling of water tanks of any type/pattern and removing from site complete all as specified and as directed.

PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to wall including dismantling of existing SWR/PVC/Salt glazed ware/AC or reinforced concrete pipe set in cement mortar etc. complete all as specified and as directed.

S&F PVC (SWR) bend/Tee/Socket etc any radius 110mm bore pipe.

S&F holder bat clamps 110 mm bore made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof complete all as specified and as directed.

Per RM

S&F PVC (SWR) bend/Tee/Socket etc any radius 75mm bore pipe.

S&F in repair stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to doors / steel windows, complete including welding wk complete all as specified and directed by engineer-in-charge.

M&L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished) in steps, jambs, pillars, cooking platforms, floor, skirtings with necessary hole for gas pipe where ever required and likes on cement mortar bedding of 20mm thick in CM 1:6 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite and including demolition of existing Granite / Granite tiles etc complete all as specified and directed.

M&L for Granite (of any type) tiles 8-10 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite including 10mm thick backing coat of cement mortar (1:4), including demolition of existing Granite / Granite tiles etc complete all as specified and as directed. (Note :- Work also includes in patches for inside or outside the hosue complete as in cooking plateform).

M&L for Glazed Ceramic coloured tiles in vertical surface size (300 x 450mm / 300X600mm) set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat of cement mortar (1:4) including dismantling of existing tiles etc, complete all as specified and directed

M&L for 10 mm thick rendering with readymix plaster (as per manufaturer's instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement on wall of up to three stories bldgs including taking down of existing plaster complete all as specified and as directed. Make of ready mix plaster : Birla Aerocon/Ultratech radiplast/ACC acoplast.

M&L for Vitrified Ceramic tiles light shade 8-10 mm thick (square/rectangular) polished area of each tiles upto 0.42 sqm but not exceeding 1.00 sqm of size (600 x 600mm / 6

00mm X 1200mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cement mortar (1:6) including dismantling of existing tiles etc complete all as specified and as directed, the shade of tile as approved by Engr-in-Charge.

M&L for Vitrified Ceramic tiles light shade 8-10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchcomplete including 10 mm thick screed bed in cement mortar (1:6) including dismantling of existing tiles etc complete all as specified and as directed.

M&L Non - Skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular)area of each tile exceeding 0.18 sqm but n exc 0.36 sqm, as in skirting laid on 10 mm thick cement plaster in CM (1:4), set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles including dismantling of existing tiles etc.complete all as specified and as directed.

M&L for Non - Skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surface including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 laying floor finishes including dismantling of existing tiles etc complete all as specified and as directed.

Demolition of concrete (unreinforcement) of any description and any position not otherwise specifically provided complete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position etc complete all as specified and as directed

Providing Precast RCC 1:2:4 type B-1 (20mm graded aggregate ) as in Drain cover slab etc including necessary form work complete all as specified and directed by Engr-in-charge.

M&L Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 (12.5mm graded aggregate) complete all as specified.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including demolition of existing interlocking tiles etc complete all as specified and as directed..

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 15mm thich screed bed or bedding layer in cement mortar (1:4), rubbing and polishing and including demolition of existing kota stone flooring etc. complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads metal frame including punching or drilling out old glazing pins/spring clips and providing and supply & fexing new 4.0 mm thick frosted sheet glass ordinary quality (in repair) and glazing with oil putty in square n.exceeding 0.5 Sqm in each pane complete all as specifed and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads metal frame including punching or drilling out old glazing pins/spring clips and providing and supply & fexing new 4.8 mm thick sheet glass ordinary quality and glazing with aluminium glazing clips & EPDM beading in square not exc 0.5 sqm in each pane complete all as specified and as directed.

M&L Rotational moulded polyethylene water storage tank white colour (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 300 litres including all accessories and dismantling of existing water tank complete all as specified and as directed.

S&F in repairs HDPE PVC lid (cover) for 300 to 1000 Litres capacity PVC tanks, complete all as specified and as directed.

S&F in replacement PVC syphone Cylinderical type Push button for low level flushing cistern complete all as specified and as directed.

M&L for 5 mm thick rendering on ceiling surfaces with readymix plaster (as per manufaturer's instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement on wall of up to three stories bldgs including taking down of existing plaster complete all as specified and as directed. Make of ready mix plaster : Birla Aerocon/Ultratech radiplast/ACC acoplast.

S&F in repairs PVC trap/floor trap with grating including jointing to waste pipe, dia of outlet 100mm in cement concrete type, B1, (1:2:4) complete all as specified and as directed.

M&L for old size Brick work with sub class 'B' bricks, straight or curgved in cm 1:4 straight or cuved on plan to exc 6m mean radius complete including demolition of existing brick work or stone masonry built in cement mortar including all quoines arches, pillar etc complete all as specified and as directed.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and elllorescent salts, trading oil, gr

esey spots etc, and applying one coat of cement base paint on wall complete all as specified.

M&L for applying two coats of cement base paint on walls after preparation of newly plastered surfaces complete all as specified.

S&F in repair factory made SFRC manhole cover of any size any shape (square/rectangular/circular) 70mm thick with frame set in cement mortar 1:4 complete all as specified and as directed.

S&F framed work as in doors or gates of angle or tubular section with gusset plates, rails, braces, Post and struts in fencing including cutting tops to shape etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepered for hanging or sliding with or including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening / welding and fixing complete including dismantling of existing steel complete all as specified and as directed. Fe 410 or Fe-130-O, or (Gde- E- 250).

S&F in repair for galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, including dismantling of existing fencing wiremess etc. as directed (each line wire to be measured) complete all as specified.

M&L for punched tape Concertina Coil (including spike and handle) with 50 turns and 600mm to 1050mm dia, width of barbed 9mm and spacing of clips 23.5 to 24.5mm C/C weight of each coil will be 15.2 + 5% Kg without packing. Coil length will be 15 mtr when opened up and including dismantling of existing concertina coil etc complete as specified.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified.

M&L for providing and injecting chemical chlorpyrifos emulsifiable concentrate for Post Constructional Anti termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M&L for Anti termite Treatment of soil under existing floors using chemical chlorpyrifos emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors all as specified .

M&L for cement plaster 15mm thick in CM 1:6 on brick or concrete surfaces finished even and smooth without extra cement mixed with by adding permeability reducing polymer @ 250 gms/sqm (6%) by weight of cementitious content at the time fixing with water as per manufacturer's recommendations incl all levelling the surface, curing including taking down of existing plaster etc. complete. Note :- Rates for water proofing compound/polymer deemed to be incl in the above rates.

S&F holder bat clamps 75 mm bore made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof complete all as specified and as directed.

M&L for Vitrified ceramic tiles (light shade) 8-10 mm thick (Square/ rectangular) colour / shade / design / size match to floor as in skirting laid on 10mm thick cement plaster in CM (1:4) , set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles including dismantling of existing tiles etc. complete all as specified and as directed.

M&L for 15 mm thick rendering with readymix plaster (as per manufaturer's instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement including taking down of existing plaster / new brick work surface complete all as specified and as directed. Make of ready mix plaster : Birla Aerocon/Ultratech radiplast/ACC acoplast. Note :- Contractor shall be bounded to carryout repair / maint upto G+4 storey building and the rate shall be deemed including scafolding / double scafolding, safety equipments and misc accessories.

Taking down carefully aluminium/copper point wiring (light/fan/bell/socket /power) with complete fittings such as steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface all as specified and directed by Engr-in-Charge.

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit and including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes factory made including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for One light/Fan/Bell point controlled by one 5 Amp switch one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) . Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

All as per item No 2 above but 5 Amp socket outlet on same board.

All as per item No 2 above One socket outlet 5 Amps on independent board.

All as Item No 2 above but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing complete.

All as Item No. 2 above but for one light point controlled by two 2-way switches with cable 1.5 Sqmm size.

M&L for concealed point wiring complete with stranded copper conductor 4 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit complete including 4 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for one socket outlet for modular AC Box on Independent board with cables 4.0 sqmm size for phase and neutral and 4 Sqmm for earthing complete. Note:- the rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/w

hite wash complete

S&F switch modular type, 1 way 6A, 1module.

S&F switch, Modular switch 2 way 6A, 1 module.

S&F Modular Socket, 6A - 2/3 pin 2 module.

S&F Modular AC box with socket and MCB SP 20 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement , complete all as specified and directed.

S&F switch modular type 1way 16A, 1module with indicator

S&F Socket 6A/16A - 2/3 pin combined .

S&F of electric bell Ding Dong type AC, 230 volts single phase all as specified.

S&F Modular Bell push 6A 1 module

Supply and fixing LED lights fitting 1x 20W, 220V, AC aluminium housing decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED lights fitting 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F in replacement of lamp holder Angle/ Batten type bakelite insulated body with back plate all as specified and directed.

S&F of LED lamp 12 Watt LED Re-Chargeable Bulb complete all as specified and directed.

Taking Down of ceiling Fan and keeping in safe coustody and refixing it back after completion of B/R work complete all as specified and directed.

Taking Down of Exhaust Fan and keeping in safe coustody and refixing it back after completion of B/R work complete all as specified and directed.

S&F Fan step regulator, 120W - 2 module type complete all as specified and directed.

S&F in replacement decorative wall light mounting suitable for LED lamp upto 12 Watt including all connections complete all as specified & directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F in replacement of LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE including all accessories connecting up twin core flexible copper conductor cable complete all as specified & directed.

S&F ceiling rose surface Bakelite 65x25mm three terminals complete all as specified.

Taking Down of Geyser and keeping in safe coustody and refixing it back after completion of B/R work complete all as specified and directed.

Supply and fix in replacement of MCB DB SPN 16 Way with metal double door, (IP43 Protection) flush mounting epoxy powder control having 100 Amps rated bus bar complete all as specified and directed .

S&F in replacement MCB SPN 63 Amps 'B' series, breaking capacity 10 Ka, 'B' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc.

S&F for MCB SP 6 to 32 Amps 240 Volts, 10kA, `B' curve all as per site requirement and as directed.

Per Point

The furniture articles shall be prepaired smooth after removing dents or tightning the frame with welding if required or providing any screw/ nut & washir if required, applying putty for planning of surfaces. All new parts/ area where there is no old paint exists, one coat of primer of best quality as approved shall be applied. The painting shall be done after prepration of surfaces paint OG/ Black/ White/ Sky Blue/ Grey replacing the existing shade/ colour achieving its glossy look. Rest all as directed by Engr in charge/ Accepting officer.

Almirah Large Steel/ Alm MAP or 1/2H 1/2 Shelves etc

Almirah Med Steel

Charpoy Folding IP

Charpoy IP Ply Top : FD/MAP-II/01

Rack Shoe Steel

Teapoy Varandha

Table Computer

Material and labour for polishing to the wooden furniture articles. Polishing the articles shall be cleaned up with a clean cloth and applying suitable sandpaper paper to remove dirt/ dust. The furniture articles/ parts shall be prepaired smooth after removing dirt/ dust etc, making wooden surfaces smooth by applying wood filler and putty on cracks / jonts and applying suitable colour to the base for prepration of base. Two coats of best quality polish as approved shall be applied for glossy look. The polishing shall be done only after prepration of surfaces. Rest all as directed by Engr in Charge/ Accepting Officer.

Bed Plywood Top : FD-246/247

Bin linen

Chair Dining : FD-279/16/250/228/MAP JCO-OR

Chair Dining long back/ MAP

Chair Easy : FD/-229/201/17

Hat Stand with mirror

Peg Table : FD-277/384, DB-3973

Side board

Sofa Set 4 Seats

Sofa Set 5 Seats

Stool drssing

Table Centre : FD-274/ 235

Table Dining 6/8 Pers

Table Wiring

Teapoy : FD-278, 34, 382

Supply and fixing in repairs, Locks with duplicate keys for Almirah large steel/ Almirah Med steel/ Almirah MAP/ Almirah 1/2H 1/2 S after removing old damaged/ unserviceable locks.