GE/PNH-35/2021-22

Amount

B&R PORTION:- Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Dismantling of timber scantling 40sqcm and over in section unframed work,as in any position, complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work,as in any position, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame n exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area exceeding 1.5Sqm but not exceeding 4 sqm each including cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and removing unserviceable material exc 100 mtr, complete all as specified and directed.

S&F Rolled mild steel works as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication as directed etc confirming to Fe 410W(Gde E-250), quality 'A', complete all as specified and directed.

S&F Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' including painted with and including one coat of primer, complete all as specified and directed.

S&F Mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-250 Gde E-165 complete all as specified and directed.

S&F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per Item No. 15 above but except sheeting complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashingfixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

M&L for Applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously untreated steel surfaces of any description, over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

S&F Suspended false ceiling using E- grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm x 0.5mm using 4mm thick high pressure stream cured classic variant E-board, designer pattern (ISI marked, IS No 14862-2000) & E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butter fly clips with & including two coats of synthetic enamel paint over a coat of primer, complete all as specified and directed. Make:- Everest Industries Ltd of equivalent as approved by GE.

All as per Item No. 19 above but except ceiling board and frame material complete all as specified and directed.

M&L for Walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per ser Item No 21 above but except stone, complete all specified and directed

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for Rendering 20mm thick on other than fair faces of brick or stone masonry wall surfaces in chajja and suspended wks cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 15 mm thick in CM 1:4 on fair faces of brick wall surface or concrete surface finished even and smooth without using extra cement including mixing of water proofing compound (WPC shall be measured and paid separately) including all necessary scaffolding, complete all as specified and directed.

M&L for Rendering 15 mm thick in CM 1:6 on brick wall surface or concrete surface finished even and smooth without using extra cement including all necessary scaffolding, complete all as specified and directed.

M&L for Preparation of new plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade including wall care putty of 1-3mm thick over plastered surface of wall, complete all as specified and directed.

M&L for Applying three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

S&F Pressed steel frame of size 125X60mm for doors as per IS 4351 using PBI Sheet of 1.25 mm thick with double rebated including mild steel hinges medium weight 100mm long, 03 Nos each for double shutter and 25X3mm flat iron in holdfast. tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc. complete all as specified and directed.

S&F Pressed steel frame of size 105X60mm for doors as per IS 4351 using PBI Sheet of 1.25 mm thick with one or more rebates including mild steel hinges medium weight 100mm long 03 Nos each for double shutter and 25X3mm flat iron in holdfast. tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc. complete all as specified and directed.

S&F 35 mm 2nd class hard wood plain framed factory made, paneled shutter (any number of panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces .The size of rail and stile as per IS :1003(Part-I ) kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated & prepare to receive glass, gauge etc (without sash bars /edges of framing plain chamfered or rounded, fitted with cut and mitred beds for securing glass etc) size of members of shutters as spd in SSR Part-I section-8 clause 8.2 (a). complete all as specified and directed.

S&F Steel windows or ventilators made out of 1.25mm thick pressed steel frame with glazed & gauged shutters (combination), side hung / top hung type with or without glazing bars as directed including box type / projecting type hinges and steel peg stay, handle, tower bolt & locking arrangement with & including guard bar provided with cooler opening, complete all as specified and directed.

M&L for Plain cement Concrete 1:3:6 type- C1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks, benching and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

S&F 300mm ordinary rat tail Mild steel rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled,50mm long complete all as specified and directed.

S&F Second class hard wood small fittings such as brakets of any type, latch and hinges blocks, shaped doors and windows stops and the like, including all necessary labour, articles not exceeding 200 cu.cm each complete all as specified and directed.

S&F Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 150 mm long complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 150 mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in base course of floor surfaces, complete all as specified and directed.

M&L for Chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry in floors and pointed with equal proportion of white and grey cement and no pigments, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm (square/ rectangular) area each tiles exc. 0.11sqm but not exc. 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed in white cement and pigment to match the shade of tiles laid over and including 15mm screed bed or beading layer in CM 1:6 complete all as specified and directed.

All as per Item No. 47 above but in vertical surfaces such as skirtings, dados and risers to steps etc including 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, complete all as specified and directed.

M&L for 40mm thick Plain Cement Concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in floor & finished the surface even & smooth without using extra cement, complete all as specified and directed.

S&F Glass dividing strip 3mm thick 38mm width,inserted in flooring, confirm to design, complete all as specified and directed.

M&L for RCC nominal mix 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in beams , cantilevers, bressummers, lintel over 1.5 mtr span, complete all as specified and directed.

Form work to sides and soffits of floor or roof beams, beam haunchings , lintels, cantilevers, shelves including supports, overhangs etc and similar works fair finished surface of concrete, complete all as specified and directed.

S&F TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

S&F TMT bars, 5mm dia and over upto incl 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, complete all as specified and directed.

S&F in repair MS powder coated tubular curtain rod fancy type of 25mm dia complete all as specified and directed.

S&F in repair MS powder coated decorative type bracket, end ball, rounded block, bracket (coated with brown/cherry/golden colour) suitable for 25mm dia curtain rod of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

M&L for Complete removal of existing treatement from wall plaster and applying two coats of cement base paint over a coat of approved primer, complete all as specified and directed.

M&L for Complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

M&L for Two coat of synthetic enamel paint over a coat of pink primer on new untreated wooden surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete all as specified and directed.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

M&L for Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS PVC insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated and unsheathed heavy duty cable drawn in and including concealed PVC rigid conduit medium grade ISI marked terminated into CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc for one light/fan/Exhaust fan point controlled by one switch one way or one fan point controlled by one way switch through regulator, complete all as specified and directed.

All as per item No 63 above but for one fan/exhaust fan point controlled by one way switch on independent board with PVC insulated copper conductor cable 1.5sqmm complete all as specified and directed.

All as per item No 63 above but for 3 Pin socket outlet 5 Amps point on same board complete all as specified and directed.

All as per item No 63 above but for 3 Pin socket outlet 5 Amps point on independent board with PVC insulated copper conductor cable 1.5sqmm complete all as specified and directed.

All as per Item No 63 above but for 6 Pin socket outlet 15 Amps point on independent board other switches with with PVC insulated copper conductor cable 2.5sqmm 1100 Volts grade, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 2 and 3 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F in repair Socket outlet multipurpose combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch piano flush type 16 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair Ceiling rose (ISI Marked) 3 Phase PVC/poly carbonate, insulated body, complete all as specified and directed.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades & depositing to store, complete all as specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan after repair if any as obtained / taken out from item No 73 above, complete all as specified and directed.

S&F in replacement LED Tube light fitting suitable for LED 20W tube rod made out of with polycarbonate housing & integrated electronic driver complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 20W LED tube rod fixed in repairs, complete all as specified and directed. Make:-Havells Cat Part No:-LHLDEFXD5L8R020 for LED tube rod & Cat Part No:-LUMILINEPLUSBS20WLED865SPCSS or Equaivalent cat part of make as specified in P.S. Note :- The LED batten and LED tube rod shall be of same make.

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings with & including LED lamp 10 watts (B-22 holder), complete all as specified. Make of LED lamp:- Havells cat part No LHlDERUEML8x010 or Equaivalent cat part of make as specified in P.S.

S&F in repair LED street light fittings 25 Watt made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 complete with hosing with all accessories pre wired with and including 40mm dia GI pipe bracket of 1.2 mtr made to shape as required fixed on wall or pole with FI clamp of required shap & 40x6mm size, nut, bolts, washers and making connection with 3 core copper flexible cable of suitable size to light fitting fixed in repairs, complete all as specified and directed. Make:-Havells Cat Part NoENDURAPEARLSL25WLED757SASYTOPCMP or Equivalent cat part of make as specified in PS.

S&F in repair MCB single pole and neutral 6 to 32 amps 240 volts 10 KA 'C' series, complete all as specified. Make: Havells Cat Part No.DHMGCSNF006-032 or equivalent in Legrand/ C&S Electric/ ABB/ Siemens/ Scheneider

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make: Havells Cat Part No. DHMGCSPF006-032 or equivalent in Legrand/ C&S Electric/ ABB/ Siemens/ Scheneider

S&F 1100 volts grade heavy duty cable PVC insulated multi stranded aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 16Sqmm including taking down existing old unsv service connection, complete all as specified and directed.

S&F in repair House service bracket (hook type), complete, with 3m long GI pipe 40mm dia medium grade, two Nos 90 degree bend, MS hook and guy or stay including taking down existing old unsv house bracket, complete all as specified and directed.

S&F in repair Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

S&F in repair Fan regulator stepped type (electronic ) flush type for 1200/1400mm sweep AC ceiling fan, complete all as specified and directed.

S&F in repair Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified. Make:- Havells cat part No-DHDPSHODPW08 or Equivalent cat part of make specified in PS.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation etc for shafts, wells,cesspits, man holes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth and getting out in hard/dense soil, complete all as specified and directed.

Excavating in trenches not exc 1.5m wide and exc 1.5 m but not exc 3.0 m in depthor foundation etc for shafts, wells,cesspits, man holes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth and getting out in hard/dense soil, complete all as specified and directed.

Returning, Filling in soil including spreading, leveling, watering and well ramming in players not exc 25cm, complete all as specified and directed.

Removal of excavated material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point, complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation of poles and mass concrete, complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in pole coping and stay assembly complete all as specified and directed.

Approved quality clean dry sharp sand as in cushioning to under ground cable laying 15cm thick before laying and 8cm after laying the cable in trenches for cable cushioning, complete all as specified and directed.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

S&F lightening arrestor HT 11 KV complete all as specified and directed by Engineer-in-charge.

Supply, laying , jointing and testing of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 11000 volts grade with stranded aluminum conductor of size 95 sqmm 3.0 core, laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts including cable gland of suitable sizes and aluminium lugs for connection, fixed as in repairs complete all as specified and directed. Make: Finolex / KEI Industries Pvt Ltd / Polycab / Gloster / Universal Cables. Note: Excavation, earthwork, sand cushioning, brick protection shall be measured & paid for separately.

Steel tubular poles, swaged type, 410 SP-55, 11m long with 300x300x6mm thick MS base plate continuously welded to pole with MS sheet 2mm thick plug welded at top, bolts, nuts and screws all as specified including two coats of black bituminous paint internally throughout and externally for embedded portion and two coats of aluminium paint over a coat of red oxide primer on exposed surfaces including painting up to 1.5 mtr height from ground level or above coping with two coats of synthetic enamel paint in 30cm strip, alternate balck & yellow starting with block at ground level, complete all as specified and directed. (Note:- Excavation and earth work and PCC shall be measured & paid separately)

M&L for Cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including nuts,bolts,washers, welding , bending cold or hot, drilling holes for bolts,in any shape or sizes as indicated or directed and inclusive of one primer coat and two coats of alluminium paint complete all as specified and directed.

Disc type insulator, porcelain, vitreous 145mm high and 255mm dia ball and socket type, white, brown or green 'Two-in-series' assembly for tension with tension clamps for conductors, working pressure 11000 volts all as required at site. Make:- BHEL/ Jaipuriya/ Jayshree

Supply and fixing loop insulator Porcelain, vitreous white/brown/green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, large size with overall dimensions 65mm x 90mm, clearance of hole 16 mm, Complete all as specified and directed. Make: PACTIL/BHEL/JAIPURIA

Supply, laying , jointing and testing of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor of size 185 sqmm 3.5 core, laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts including cable gland of suitable sizes and aluminium lugs for connection, fixed as in repairs complete all as specified and directed. Make: Finolex / KEI Industries Pvt Ltd / Polycab / Gloster / Universal Cables. Note: Excavation, earthwork, sand cushioning, brick protection shall be measured & paid for separately.

M&L for Pin type porcelain vitreous white brown or green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 150 mm height, 150 mm dia for 11000 volt grade complete all as specified and directed.

ACSR conductor of any size and any type including stretching, fixing and binding to insulator on OH/ LT line service feeders all as specified including aluminium binding wire or aluminium tapes complete all as specified and directed.

Supply, installation, commissioning and testing of servo motor controlled voltage stabilizer for automatic operation on unbalanced load, three phase naturally oil cooled outdoor type (IP-55), copper wound with MCCB and bypass system and designed for input variation between 210V to 480V with output voltage stabilized at 415V with accuracy + 2.5% and speed of correction 8 volts per second and of capacity 63 KVA complete all as specified and directed. Make: Volina/ AE/ Electrifield/ Vinitec

S&F Cable jointing kit for 11 KV (earthed) grade cable for out door termination, heat shrinkable type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size of 50 to 95 Sqmm complete all as specified and directed.

S&F Stay assembly for electric pole complete with accessories as shown in electrical plate No. 1 of SSR Pt-I and drg using stay rod of 20mm dia , complete all as specified and directed. Note : Excavation,earthwork, PCC and loop type insulator shall be measured and paid separately.

Supply and install HT 11 KV outdoor gang operated air break switch suitable for horizontal or vertical mounting with drop out fuse having 9 insulators of rating upto 400 Amp complete all as specified and directed.

S&F Earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6.0 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 32 x 6 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 8 mm dia TMT bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified and directed. NOTE: The unit rate includes earth strip and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point.

M&L for construction of platform suitable for 63 KVA Transformer/ Voltage stabilizer of size 3.0m x 3.0m x 1.5m (Platform shall be made out of brick masonary one feet below ground level and one feet above ground level hollow space and to filled by PCC 1:3:6 type C2 foundation below ground level), made out of 23cm brick masonary in cement mortar 1:6 ( below ground level, hollow space to be filled hardcore of size not exc 63mm, deposited, spread and levelled in layers not exceeding 15cm thickness, watered and well rammed) with 1 100mm thick cement concrete 1:2:4 type B2 as in floor of platform, plastering in CM 1:4 complete all as specified and directed.

M/S SV CONSTRUCTIONS

m/s maqsood ahmed

M/S FAIZ AHMED KHAN