REPAIR/MAINTENANCE TO JOINERY FLOORING PLASTERING AND SANITARY FITTINGS IN BLDG OF 58 GTC AT HAPPY VALLEY UNDER GE SHILLONG

Amount

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) not exc. 1.5 sq. m each all as specified.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each all as specified.

Taking down shutters of any description exc 1.0 sqm but n. exc 2.0 sqm each all as specified

Taking down shutters of any description exc 1.0 Sqm and nexc 2 sqm each and refixing in same opening complete.

Taking down shutter of any description not exc 1 Sqm each complete all as specified.

M&L for Resecuring or easing & adjusting without taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified.

M& L Resecuring or easing & adjusting without taking down Shutters of any description n exc 1 sq. m each complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below/above ground level) all as directed.

Demolition of Brickwork or stone/boulder masonry or precast concrete block walling, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework built in cement mortar complete all as specified.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed.

Taking up or down steel tubing and connections for 15 mm bore of pipes complete all as specified and as directed.

Taking up or down steel tubing and connections for 20 mm bore of pipes complete all as specified and as directed.

Dismantling of timber scantling 40 sqcm over in section in any position (unframed work) complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof covering complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and as directed.

Dismantling of wall/ceiling boards (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets complete all as specified and as directed.

Demolition and breaking up drain pipes 100 mmdia (salt glaged ware AC or reinforced concrete) set in cement mortar complete all as specified and as directed.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

M&L 2nd class hard wood in scantling clean sawn timber fixed all as specified.

M&L Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with Two coats of Creosote complete all as specified and as directed.

S&F 40mm thick 2nd class hard wood boarding in floors and skirting plained one side with butt joints and fixed with nails complete all as specified.

S&F 20mm thick 2nd class hard wood boarding in eaves board/fascia plained both sides with butt joints fixed with nails complete all as specified.

S&F Anodised Aluminium frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mm c/c using GI hangers of 6mm dia GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed .

M&L non asbestos fibre cement building boards of 4mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping complete all as specified and as specified.

M&L for applying two coats of distemper oil emulsion on ceiling over and including a coat of chalk whiting including preparation of new or undecorated surface complete all as specified and as directed.

M&L for 2nd calss hard wood plain fillets bullnosed , splayed , chamfered , or rounded on one face or edge in section wrought secured with nails or brads sectional area exc 3 n exc 6 Sqcm including dismantling of old planin fillets all as specified and as directed.

M&L for preparation of new or previously untreated wooden surface of any description n.exc 10 cm width or girth applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and directed

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM 1:3 complete all as specified and as directed

M&L for Non skid coloured joint free ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Non skid, coloured, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 10mm thick rendering in CM 1:3 complete all as specified and directed

M&L for Non skid, coloured, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Non skid, coloured, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface of size 300x 450x 7 mm/ 300X 600X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour over 10mm thick backing coat in CM 1:3 complete as specified and directed

M & L Granite (of any type) work 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismanlting of old granite work complete all as specified and as directed.

M&L for machine pressed pre polished chequered cement concrete tiles 30cm x 30cm x 25mm thick over 15mm thick screed bed in CM 1:4 set & jointed in neat cement slurry with white cement and pigments as in floor complete all as specified

M & L for PCC 1:2:4 type B1 (Using 20 mm graded aggr) as in steps, parapets, railings upto 60cm in height, coping, bed plates etc. and similar works incl weathering, slightly rounded or chamfered angles and throating including necessary from work all as specified and directed.

M&L for 100mm thick cement concrete using (40mm graded aggregate) type D-2 (1:4:8) all as specified.

M&L for 75mm thick cement concrete using (40mm graded aggregate) type C-2 (1:3:6) all as specified.

M&L for 25 mm thick cement concrete 1:2:4, Type B-0 (12.5mm graded aggregate) as in floor for tiles all as specified.

M&L for PCC 1:3:6 type C-2(using 20 mm graded cr. stone aggr),75mm thick as in plinth protection finished even and smooth without using extra cement layed in bays not exc. 2.00m and joints filled with bitumen sand mastic with ratio (1:3 )complete all as spd & dir.

M&Lfor Precast cement concrete block masonry with solid block exc 10 Cm in width with PCC, type C1 (1:3:6) using 20mm graded stone aggregate) and setting in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15mm thick on fair faces of concrete surface of wall in CM (1:4) finished even and smooth without using extra cement all as specified and directed.

M&L Rendering 10mm thick on concrete surface of wall in CM (1:6) and finished the surface fair & even without using extra cement , complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of primer all as specified.

M & L prepration for newly plastered surfaces and applying two coats of distemper over a coat of primer complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified.

S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35 mm thick 2nd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(a) all as specified.

S&F 30mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(b) all as specified.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

All as per item no 56 above but fixing as in repair complete all as specified.

S&F figured sheet glass , ordinary quality 4.00 mm thick and glazing with oil putty in square not exceeding 0.5 sq m in each pane complete all as spd.

All as per item no 58 above but fixing as in repair complete all as specified.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

All as per item no 60 above but fixing as in repair complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed tothe stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, supplying & fixing in openings as per specification complete all as specified and as directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 75mm.

S&F Extruded Aluminium, anodised, bow handles of size 150mm.

S&F Extruded Aluminium, anodised, bow handles of size 100mm.

S&F aluminium anodised barrel tower bolts of extruded section and fixed of 200 mm length

S&F aluminium anodised barrel tower bolts of extruded section bolts and fixed of 100 mm length

S&F Aluminium alloy, anodised sliding door bolts(300mm long) with hasp,staples ( bolt type) and fixing clip of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified.

M&L Aluminium anodized frame Powder Coated (minimum thickness of powder coating 50 micron) for doors , windows , ventilators with one or more rebates incl joing cleat for fixing etc complete all as specified

S&F Anodised aluminium window and ventilator shutters, Powder Coated (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

S&F anodised door shutters , Powder Coated (minimum thickness of powder coating 50 micron) aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified

S&F Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beadingcomplete all as specified and directed

M&L 12mm thick prelaminated particle board, interior grade prelaminated both side with decorative choice laminations ,fixed with screw etc complete all as specified.

S&F in repair Aluminium extruded section door closer hydraulially regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm width and of weight of between 61 to 80 kg and fixed (ISI Marked) complete all as specified

S&F in repairs brass mortice lock, vertical type size 100mm 2 levers complete all as specified

S&F in repairs brass mortice lock, vertical type size 100mm 4 levers complete all as specified

M&L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cocer, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, fixed in repair.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.complete all as specified

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified

M&L for preparation of new or previously untreated surface of steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

S&F in repair vitreous china wash down water closet padestral patern EWC ,white, including trap set, seat cover and conection to trap, flushing pipe, etc. complete including making good to floor fixing bolt all as specified and directed.

S&F in repair Plastic Water closet seat cover, black/white closed pattern with flat bottom, and cover and mild steel chromonium plated or aluminised hinging devices, complete all as specifed and directged. Make : Parrywire, Hindware or equvalent .

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580 X 440 mm white, with integral foot rests including provision of lime concrete bedding, including fixing of flushing cistern and flush pipe all as specified and directed

S&F in repair PVC valveless, syphonic action type flushing cistern, low level, white, 10 Ltr capacity with inlet, ball valve, float and handle including brackets all as specified and directed

S&F in repair Vitreous china WHB, white, flat back, size 550 x 400 mm including brackets, 32 mm waste coupling and 32 mm waste fittings all as specified and directed

S&F GI steel tubing medium grade 15mm bore with all fitting and fixed complete to wall and ceiling or laid under in floor all as specified and directed

S&F GI tubes, medium grade galvanised, 20mm bore with all fitting and fixed complete to wall and ceilings or laid in floors all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes incl bedding in CM to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915x460 mm bowl size 410mmx360mmx160 mm all as specified and directed

S&F Stainless steel kitchen plate rack of size 31" X 30' X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack (Make : Blue star, Cat No - BSKPR-314)

S&F in repair pillar taps cast copper alloy with capstan heads, chromium plated, fancy type,screwed down high pressure with or without lettered HOT or Cold wih long screwed shankes and flynuts for 15 mm bore all as specified and directed

S&F in repair Bip tap, chromium plated, 15mm fancy type all as specified and directed

S&F in repair Angular stop cock, fancy type, chromium plated, 15 mm bore (Make : SONA or equivalent) all as specified and as directed

S&F PVC connections 15 mm size with PTMT nuts of length 450mm all as specified and as directed

S & F in repairs Tubular Towel rod , D type 60cm long brass Chromium plated all as specified and as directed

S&F in replacement of rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 Ltrs incl taking down old unservicable tank of any capacity all as specified and directed

S&F in replacement of rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 Ltrs incl taking down old unservicable tank of any capacity all as specified and directed

S&F in repair float valve of size 20mm, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe all as specified and directed

S&F in repair tank nipple suitable for HDPE water tank of size 15mm dia bore

S&F in repair tank nipple suitable for HDPE water tank of size 20mm dia bore

S&F Gun metal gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for following bore of pipe including taking down old existing unserviceable gate valve of dia 20 mm complete all as specified and directed by Engr-in-Charge

S&F in repair PVC (SWR) bends, any radius, 110 mm bore all as specified and as directed

S&F in repair PVC (SWR) Pipes single socketed in any length with rubber ring joints, 110 mm bore fixed to walls complete as directed

S&F in repairs CP over head shower dia 100mm round shape single flow (ABS body chrome plated with gray face plate) with rubit cleaning system Cat part No: OHS-1989with CP shower arm dia 20 mm & 450 mm long round shape without bend for wall mounted showers with flange Cat part No: SHA-49483 or equivalent

S&F in repairs CP single lever wall mixer 3-in-1 system with provision for bath hand shower & overhaed shower complete with 115 mm long bend pipe connecting legs & wall flange (without hand & ober head shower) of make Jaquar cat part No:OPP-15125PM or equivalent

S&F in repair 15 mm bore CP health Foucet cock with Flexible pipe 1 m long of make Jaguar Cat Part No:ALD-565 or equivalent all as specified and as directed

S&F Soap dish holder of make Prayag Cat Part No:-BA-05 or equivalent all as specified and as directed

S&F in repair Toilet roll holder with stainless steel of make Jaguar Cat Part No:- AKP-35755PS or equivalent all as specified and as directed

S&F in repair Towel ring sqare shape stainless steel of Make Jaguar Cat Part No:-CAN-1121N or equivalent all as specified and as directed

S&F in repair corner glass shelf with bracket of make Jaguar Cat Part No:CAN-1173 or equivalent all as specified and as directed

S & F in repairs Vitreous China EWC including seat cover closed pattern single piece size 755x365x655 complete of make Jaguar Cat Part No :- LYS-WHT-38851PSM or equivalent all as specified and as directed

M/S MANOJ KUMAR BAL

M/S Nakul Chandra Samal

M/S U.K ENTERPRISE

S K DEY

Ms Amrik Singh Bahra