REPAIR/MAINT TO TILING AND OTHER MISC WORKS IN VARIOUS ZONES AT TALBEHAT MIL STN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M/L for non skid Coloured ceramic tiles coloured 7 to 8mm thick (square/rectangular)area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the Tiles over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed by Engr-in-charge.

M&L glazed colour ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick cement plaster in CM 1:4 complete all as specified and as directed

S&F vitrified ceramic tiles 10mm thick (square/ rectangular) polished, light shade, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick screed or bedding in CM 1:6 complete all as specified and as directed.

S&F vitrified ceramic tiles 10mm thick (square/ rectangular) polished, light shade, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in as in vertical surface like dado/ skirting etc including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L of Kota stone slab 20-25mm thick in floor, riser of steps, skirting, dado and pillar laid over 20 mm cement screed bed in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note:-All exposed edges of kota stone flooring shall be finished as half round/bull nosed as approved Engr-in-Charge

Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid / bedded and pointed in any mortar.

M & L for marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms with and including 20mm thick cement screed bed CM1:3 including pointing in white cement(1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed

M&L for Heavy duty ceramic tiles size 300x300x 8-10 mm thick any colour set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tile laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 75 mm thick plain cement concrete (1:3:6) type C-2, (using 40mm graded stone aggregate ) as in plinth protection finishing concrete surface even and smooth without using extra cement complete all as specified & as directed.

M & L for coloured/grey designer concrete tiles size (30cmX30cmX25mm)and 15 mm thick cement screed bed CM 1:4 thick set, jointed and pointed in neat cement slurry in floors with white cement and pigment including dismantling of old concrete tiles with cement mortar bedding complete all as specified and as directed.

Taking up or down 15mm dia steel tubing and connection including removal complete all as specified and as directed

Taking up or down 20mm dia steel tubing and connection including removal complete all as specified and as directed

Taking up or down 25mm dia steel tubing and connection including removal complete all as specified and as directed

S&F for 15mm bore steel tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and as directed

S&F for 20mm bore steel tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and as directed

S&F for 25mm bore steel tubes medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and as directed

M&L for cutting of brick wall chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing steps, cills, sunshades shelves, lintel etc and water tubing etc and making good cutting not exc 10cm girth complete all as specified and directed

Demolition of brickwork built in cement mortar with all quoins, pillars etc complete all as specified and directed

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 straight or curved on plan exc. 6m mean radius, using old size bricks, complete and all as specified and directed

S&F in repairs for vitreous china wash basin white flat back size 550X400mm but exclusive taps, wastes, chain and plug and porcelain stopper but including cutting for and pinning in ends of brackets or erecting stand, including waste pipe brackets fixed in repairs complete all as specified and as directed

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440mm with integral foot rest including 'P' or 'S' complete and all as specified and directed. Make:-johnson peddar,Hindware (1st quality) ,Parryware (superfine)

S&F in repair vitreous china wash down water closet (Pedestal pattern) white with plastic seat cover (excluding fixing of bolt of flushing cistern and flush pipe) including all fittings complete all as specified and as directed

S&F in repair 10Ltrs capacity low level PVC flushing cistern (ISI mark) valveless, symphonic type, white with inlet, ball float and handle including brackets complete all as specified and as directed

S&F 15mm bore PVC connection 450mm long complete all as specified and as directed

S&F in repair for CP faucet slimline health faucet chromium plated,with hose &hook Make:- parryware, prayag, Jaquar

S&F Half/quarter turn chromium plated 15 mm bore wall mixture 3 in 1 with provision for over head shower with 115 mm LB pipe & wall flange complete with bend pipe and wall flange, complete all as spfd & directed ,Make:_ Parryware, Hindware, Jaqur.Prayag

S&F brass Chromium plated shower rose 125 mm size with or without swivel joints any size incl fixing of steel pipe or union all as spfd & directed by Engr-in-charge.,Make:_ Parryware, Hindware, Jaqur.Prayag

S & F in repair 15mm bore light angular stop valves with wall flange, Half Turn / Quarter turn, fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make : Parryware , Hindware ,Prayag, Jaquar

S & F in repair 15mm bore bib tap, foam flow with flange, Half Turn/ Quarter turn, fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed. Make : Parryware , Hindware ,Prayag, Jaquar

S & F in repair 15mm bore pillar tap, foam flow with flange, Half Turn/ Quarter turn, fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed. Make : Parryware , Hindware ,Prayag, Jaquar

S&F Half Turn / Quarter turn, 15mm dia CP central hole basin mixer without pop up waste system with 450 mm flexible hose for mixing of hot and cold water screwed for iron pipe and fixed complete all as specified and directed. Make : Parryware or Hindware , Prayag or Jaquar

S&F in repair brass chromium plated towel rail 20mm dia D type 60cm long between flange all as specified and directed by Engr-in-Charge

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm bowl size 410mm X330mm x160mm complete al as specified and as directed

S&F sinks without made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size495mm X 420mm bowl size 410mm X330mm x160mm complete al as specified and as directed

M&L32 mm boreWaste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

S&F in repair bevelled edge looking mirror 5.5mm thick of size 60cmx 45cm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as spfd and directed by Engr-in-charge.

Dismantling water tanks of capacity exc 250Ltr and n.exc 500Ltr and removing to store

Dismantling water tanks of capacity exc 500Ltr and n.exc 1000Ltr and removing to store

S&F rotational moulded polyethylene water tank of 500Ltrs capacity (Cylindrical vertical with closed top) noticed and portion all as specified SSR Part-I

S&F rotational moulded polyethylene water tank of 1000Ltrs capacity (Cylindrical vertical with closed top) noticed and portion all as specified SSR Part-I

S&F 20mm ball value high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe all as specified and as directed

S&F in repair 20mm ball value high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe all as specified and as directed

S&F 15mm ball value high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe all as specified and as directed

S&F Grating round 110mm dia of CP complete all as specified and as directed

S&F in repairs gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm dia complete all as specified and as directed

M & L for 15mm thick plastering in cement mortar 1:3 on the faces of brick work or concrete surfaces with out using extra cement and mixed with liquid water proofing compound in vertical and bottom surface complete all as specified and directed. Note:- Liquid water proofing solution should be provided in 150ml in 50Kg cement by weight and the water proofing solution supplied and paid separate items complete all as specified and as directed

M&L for PCC 1:2:4 type Bo using 12.5mm graded stone aggregate mixed with water proofing compound as per manufactures instruction on bottom up sunken portion with proper slope towards spout/spouts. Complete all as specified and as directed. Note:- Liquid water proofing solution should be provided by 150ml in 50Kg cement by weight and the water proofing solution supplied and paid separate items complete all as specified and as directed

M&L of water proofing treatment to sunken floor complete all as specified and as directed with following course of description below: (a) Applying one layer of cement slurry @ 0.688kg/Sqm mixed with acrylic based polymer modified chemical composite compound coating @0.253Kg/Sqm of make of approved in manufactures instruction and the allowed as cure for 4 Hours. (b) Second layer of cement slurry @0.240Kg/Sqm mixed with acrylic based polymer modified chemical composite compound coating @0.120Kg/Sqm and be allowed to a cure for 4 Hours. to following with max curing and testing for leak proof by ponding for 72 hours.

M&L for PCC 1:5:10 type E-2 as in foundation, sub base of floor and mass concrete using 40 mm graded stone aggregate.

M&L for 50mm dia GI pipe as in spout to drain out if any leakage occurs in the sunken portion complete all as specified and as directed

Supply only liquid water proofing compound

Taking down shutters of any description n. exc 1 sqm each as directed.

S&F solid PVC door frame of size 50x47 mm made out of 5mm PVC sheet reinforced with MS square tube as per specification drying as per manufacture instructions including all necessary fitting complete.

S&F 30mm thick factory made solid panel PVC door shutters made out of MS tubes of top and bottom rail MS frame shall be covered with heat moulded PVC "C" channel 5mm thick and having width of 50mm for from stiles and H section of 100mm wide for the rails, the inner panel 6mm thick PVC sheet insulated between frame and panel should be struck to the stiles and rails 50x30x5 mm, channel rails 100x30x5 mm H junction. The size, design and pattern of the panelled shutter shall be proceed by GE / Eng-in-Charge and all as per drawing / manufacture instructions complete all as specified including locking device and all necessary fitting etc here and after complete Make :- Rajshri , Sintex,

S&F butt hinges 100mm extruded aluminium alloy with galvanised mild steel hinges pin anodised and fixed.

S&F 125mm size aluminium alloy handles, fabricated type extruded section, ISI marked all as specified.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed.

S & F in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames with tinned tacks or galvanized wire staple & complete all as specified and directed

Hacking out old broken glass (any thickness, size ,quality or description) from metal or wooden frame including punching or drilling out old glazing, pins, spring clips complete all as spd & directed.

S & F sheet glass, ordinary quality 3mm thick fixed with oil putty size of glass not exc 0.50 Sqm in each pane for steel or wooden window fixed with wooden bead and pin tacked complete all as specified and directed.

S & F figured glass pin headed type, 3 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane for steel or wooden windows/doors fixed with wooden bead and pin tacked complete all as specified and directed.

S&F 0.9 to 1.5m bottom door seal brown Aluminium frame 38 to 45mm width all as specified and directed

M&L RCC 1:2:4, Type B-1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roors, landings, balconies, canopies, deck slab and in shelves and including necessary form work etc complete all as specified and directed.

M&L for mild steel TMT bars 6-8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia. or securing with clips complete all as specified and directed.

Taking down rain water pipes ( any size or pattern) inch all fittings , shoes, bends, swan neck etc. and removal to store

S & F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls.

S & F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls.

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F for 110 mm bore PVC (SWR) bends of any radius including door system complete all as specified and as directed..

S & F for 75 mm bore PVC (SWR) bends of any radius including door system complete all as specified and as directed..

S & F for 110 mm bore PVC (SWR) shoe of any angle complete all as specified and as directed.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal 110mm dia.

S&F PVC (SWR) junction single, equal or unequal 110mm dia.

S&F PVC (SWR) reducers 110mm dia.

Taking down cement plaster on brick walls incl. raking out joints, hacking for key, scrubbing down with water etc.

M & L 15mm thick plaster in C.M. 1:6 on fair surfaces of walls finished even and smooth w/o using extra cement all as specified

M&L for 15mm thick external plastering in cm (1:4) on fair faces of brick work or concrete surface including finishing the surfaces fair and even complete all as specified and as directed

Material and labour for 5mm thick in CM 1:3 rendering on fair faces of brick or concrete surfaces on ceiling finished even and smooth without using extra cement.

M & L for applying 2 coats of oil bound distemper over a coat of primer on new or previously untreated surfaces of wall including preparation of surfaces all as specified and as directed.

M&L for applying 2 coats of cement base paint in any colour over a coat of primer on new or previously untreated surfaces of wall complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on ceilings.

M&L for preparing plastered or unplastered surfaces of wall, pillasters, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spot and applying one coat of white wash

Description same as per item No 85 above but applying subsequent coat of white wash on walls

Description same as per item No 85 above but on ceiling in lieu of walls complete all as specified and as directed

M&L for preparing of surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying one coat of oil bound distemper in any colour complete all as specified and as directed.

Description same as per item No 88 above but applying subsequent coat of oil bound distemper on walls

M&L for preparing of surfaces of walls by washing rubbing down & stopping of painted surfaces and applying one coat of cement base paint, in any colour complete all as specified and as directed

Description same as per item No 90 above but applying subsequent coat of cement base paint on walls

M&L for preparation of plastered surfaces of wall and applying one coat of weather proof exterior emulsion paint all as specified and as directed Make:- Apex(Asian)/Weather coat all guard

M&L for preparation of plastered surfaces of wall and applying Subsequent coat of weather proof exterior emulsion paint all as specified and directed Make:- Apex(Asian)/Weather coat all guard

M&L for preparation of old painted surfaces of wood & wood based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint (Ist quality) complete all as specified and as directed

M&L for preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

M&L for writing letters or figures Indian or Roman size of 100mm height using synthetic enamel paint complete all as specified and as directed Make:- Berger Paints(Luxol)/Acro paints(Acrogold)/ Nerolac Paints

M&L for dots, commas, shor line, dashed, hyphens, brackets, etc using synthetic enamel paint complete all as specified and as directed Make:- Berger Paints(Luxol)/Acro paints(Acrogold)/ Nerolac Paints

M&L for JK/Birla white putty 3mm thick to have even and smooth surface complete all as specified and as directed

M&L for complete removal of existing treatment on wall of any description and applying two coat of oil bound distemper over one coat of primer complete all as specified and directed by Engr In Charge

M&L for dubbing out average 15mm thick in CM1:4 on irregular faces of walls or concrete chajjas, ceiling, parapets etc on similar surfaces (at any height of building) including necessary scaffolding complete all as specified and as directed

Repair to Aluminium window / door/partition including necessary welding, riveting, easing drilling taking down replacement of unserviceable hanging devices making them in serviceable condition and refixing in same opening complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete and directed Engr-in-Charge

Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified

Dismantling of boarding, any description, fixed in any position with screws complete all as specified and as directed

M & L for 12mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations, fixed to aluminium frame work all as specified and directed

S & F for Mortice locks 100mm size brass four levers vertical type.

S&F in repair position 4.8 to 5mm thick of ordinary quality and glazing with glazing clips including necessary rubber packing to aluminium frame n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F in repair position 4.8 to 5mm thick of figured glass, pin head type and glazing with glazing clips including necessary rubber packing to aluminium frame n.exc 0.5 sqm in each pane complete all as specified and as directed.

S&F in repair position 4.8 to 5mm thick frosted on one side type with glazing clips including necessary rubber packing to aluminium frame n.exc 0.5 sqm in each pane complete all as specified and as directed.

S&F in position 4.8 to 5mm thick frosted on one side type with glazing clips including necessary rubber packing to aluminium frame exc 0.5 sqm in each pane complete all as specified and as directed.

M/S A.R BUILDERS

M/S SHIVA TRADERS

HARNAM SINGH ANIL SINGH