Renovation of House no.148 A Police Pool Type-I in Police Station, Sector-26, Chandigarh fall under the jurisdiction of SDE W/s Sub Division No.12, U.T., Chandigarh.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)4.1.3

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)4.1.10

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :6.4

Cement mortar 1:4 (1 cement : 4 coarse sand)6.4.1

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.15.6

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:17.7

White Vitreous China Flat back Wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap. 17.7.7

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: 17.1

610x460 mm bowl depth 200 mm17.10.2.2

Providing and fixing white vitreous china water closet squatting pan (Indian type) :17.13

Orissa pattern W.C. pan of size 580x440 mm 17.13.2

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.17.19

10 litre (full flush) capacity-white 17.19.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.17.28

Flexible pipe17.28.2

32 mm dia17.28.2.1

Providing and fixing collar :17.57

Sand cast iron S&S as per IS - 398917.57.1.2

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :17.6

100 mm inlet and 75 mm outlet17.60.2

Sand cast iron S&S as per IS - 398917.60.2.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall18.1

20 mm dia nominal bore18.10.2

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :18.11

15 mm dia nominal bore18.11.1

Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end) :18.17

20 mm nominal bore18.17.1A

Providing and fixing uplasticised PVC connection pipe with brass unions :18.21

30 cm length18.21.1

15 mm nominal bore18.21.1.1

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :18.46

15 mm diameter bore18.46.1

20 mm diameter bore18.46.2

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.18.48

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 18.49

15 mm nominal bore 18.49.1

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.18.52

15 mm nominal bore18.52.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893118.53

15 mm diameter bore18.53.1

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.18.53A

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.18.62

20 mm nominal bore, 120 mm long, weighing not less than 198 gms18.62.2

Cutting holes up to 30x30 cm in walls including making good the same:18.76

With common burnt clay F.P.S. (non modular) bricks18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.18.77

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards. NSR

15 mm nominal bore

Construction of curb with CC 1: 2: 4 along with upto 1.00 depth for made it proof water including cost of sand , bajri complete in all respect NSR

Providing and fixing CP Towel rail 600 mm complete in all respect as per entire satisfaction and approval of make by EIC.NSR

Providing and fixing of CP brass revolving joint shower, CP cup with arm complete in all respect NSR

Providing and fixing of drip seal joints complete in all respect NSR

Providing and fixing C.P. Soap dish holder complete in all respect as per entire satisfaction and approval of make by EIC.NSR

Providing and fixing of C.P. Steel Grating Heavy (With hole without hole) NSR

Providing and fixing of CP Brass towel ring complete at site for WHB as per approved make complete in all respect as per entire satisfaction and approval of make by EIC.NSR

Providing and fixing SFRC Inspections chamber cover 600x600x35 mm thick made out of M.S angle iron size 35x35x5 mm and TMT bars 10mm i/d both sides including cutting welding and fixing with cement concrete 1:1/2:3 complete.NSR

Providing and fixing of SFRC G.T cover 375x375x25 mm thick made out of M.S angle iron size 25x25x5 mm thick with fixing wire mash 1"x1" of 10 gauge including cutting welding and fixing with cement concrete 1:1/2:3NSR

Providing and fixing of tank nipple complete in all respect.NSR

Providing and fixing 550x400 mm beveled edge mirror of superior glass (of approved quality) complete with 5 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers completeNSR

Providing and fixing CP waste 32mm x 150mm long complete in all respect.NSR

Providing and fixing PVC Pipe 4" (100mm Nominal bore) i.e. 6 Kg/ sq pressure complete in all respectNSR

Providing and fixing C.P long bend 32 MM complete in all respectNSR

Providing and fixing of HCI P trap 4" dia complete in all respect.NSR