REPAIR/REPLACEMENT TO FLOORING, PLASTERING, JOINERY, BRICK WORK, RCC CHAJJAS, PLUMBING WORK INCLUDING SANITARY FITTINGS AND FIXTURES, ROOF TREATMENT ETC AT VIGYAN VIHAR AND TECHNICAL AREA AT ADRDE AGRA UNDER GE I RnD DELHI

Amount

Taking down cement plaster on brick/stone walls etc any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick plaster other than fair faces in CM 1:6 on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick plaster in CM 1:4 on fair faces of brick/concrete work mixed with WPC finished surface even and fair complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for rendering 10mm thick plaster in CM 1:3 on concrete surfaces of ceiling complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over 2mm thick wall care putty (in two layer, each layer minimum 1mm thick) complete all as specified and directed.

All as per item Ser No 6.00 above but on ceiling.

M&l for preparation of newly plastered ceiling surface and applying two coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of base coat primer complete all as specified and directed.

M&L for complete removal of the existing surface of walls and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of exisitng surface of walls and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty (in two layer, each layer minimum 1mm thick) complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of Exterior emulsion paint complete all as specified and directed.

Taking Down Chowkhat or frames not exe 1.5 Sqm each with shutters (without taking off shutters) from the frames and making good the distrubed surface complete all as specified and directed.

Taking Down Chowkhat or frames exe 1.5 Sqm but not exceeding 4 Sqm each with shutters (without taking off shutters) from the frames and making good the distrubed surface complete all as specified and directed.

Taking down shuttes of any descriptions exc 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed.

Refixing shutter in same opening exc 1 Sqm not exceeding 2 Sqm complete all as specified and directed.

S&F Pressed steel frames 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F Pressed steel frames 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for 35mm thick 2nd class hard wood factory made plain framed paneled shutter (any number of panels), with lock rail and panel of 12mm thick BWP veneered particle board with commercial veneering on both faces. The sizes of rails and stiles as per IS:1003 (Part -I) Kiln seasoned and chemically pressure treated fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made glazed and skeletan shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers provided with stiles and rails complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F steel windows with side hung shutters glazed or gauged including projection type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welding complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S&F Stainless steel wire cloth grade SS-304, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Sheet glass, ordinary quality 4.00 mm thick and glazing with oil putty in square and area not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F figured glass, ordinary quality 4.00 mm thick and glazing with oil putty in square and area not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F factory made PVC door frames of size 50mmx47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suitable for opening as per site condition complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F stainless steel butt hinges of size 100mm, medium weight, cold rolled stailess steel complete all as specified and directed.

S&F 300 mm long Aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminum alloy complete all as specified and directed.

S&F 250 mm long Aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminum alloy complete all as specified and directed.

S&F in repairs 250 mm long Aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminum alloy complete all as specified and directed.

S&F 200 mm long Aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

All as per item Ser No 33.00 above but 150 mm size.

S&F 150mm long aluminium handles, cast type, anodized and fixed complete all as specified and directed.

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F in repairs 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs150mm long aluminium handles, fabricated type, D shape, anodized and fixed complete all as specified and directed.

S&F 140mm long floor door stopper aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and directed.

S&F in repairs140mm long floor door stopper aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and directed.

S&F 3mm thick Sheet glass ordinary quality and glazing with oil putty in square area not exeeeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 4.8mm thick Sheet glass ordinary quality and glazing with oil putty in square area exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 4mm thick figured glass, pin headed type and glazing with oil putty in square area not exceeding 0.5 Sqm each pane complete all as specified and directed.

M&L for preparation of old painted wood and wood base surface of any discription not otherwise discribed over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces over 10cm width or girth and applying two coats of synthetic enemel paint complete all as specified and directed.

Taking down old loose concrete surface from wall, ceiling column, beam slab etc and applying a coat of epoxy resin on concrete surface @ 0.30 kg/Sqm including preparation of surfaces as per manufacure's instructions with welded wire mesh lathing off metal stubbing joint etc in ceilings, chajjas, beam &columns etc includings all laps cutting & waste applying 25 mm thick (average thickness) of cement and sand (fine grit)in ratio 1:4 mixed with chloride free spray concrete plasticizer as per manufacture's instructions with guniting maching of pressure capacity not less than 5 Kg/Sqcm on concrete surface (excluding paraptes in paches)area n/exc 5 sqm in each patch at different site locations and surface finished fair and even to match existing tint concrete surface & finished the surfaces fair and even complete all as specified and directed. Note: Welded wire mesh shall be measured and paid separately.

Supply only hard drawn steel wire fabric not exceeding 4 kg/Sqm, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia complete all as specified and directed.

Dismantling cast iron work of any description complete all as specified and directed.

S&F framed brakets of angles or tees with web and flanges out to shape, drilled and countersunk forscrew, including bending and welding angles as necessary gusset plates, riveting etc n exe 10 Kg each bracket conferming to Fe-410 or FE-310-0 complete all as specified and directed.

M&L in repair for 50mm thick sand stone slabs in shades, Chajjas, shelves etc. Punched dressed on face and along exposed edges self faced on other side and set & pointed in cement mortar 1:4 etc complete in repairs complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings in Brick wall where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves, lintels, etc. ; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10cm girth (Brick walls) complete all as specified and directed.

Cutting chases, pinning in, making good to facings in Stone concrete block or slabwalls wall where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. ; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10cm girth complete all as specified and directed.

Taking up or down steel water tubing 15mm bore and connections including cleaning for refixing or removal from site complete all as specified and directed.

All as per item Ser No 55.00 above but 20mm dia.

All as per item Ser No. 55.00 above but 25mm dia.

Refixing old GI steel tubing 15mm bore with all fittings in new or old position (walls, ceiling, floors) complete all as specified and directed.

All as per item Ser No 58.00 above but 20mm bore.

S&F GI tubing medium grade 15 mm bore with all fittings fixed to wall/ceilings or laid in floor complete all as specified and directed.

S&F GI tubing medium grade 20 mm bore with all fittings fixed to wall/ceilings or laid in floor complete all as specified and directed.

S&F GI tubing medium grade 25 mm bore with all fittings fixed to wall/ceilings or laid in floor complete all as specified and directed.

S&F CPVC pipes SDR 11 including plain CPVC SDR 11 new fittings outer dia of pipe 16mm on walls/ceiling or in floor complete all as specified and directed

S&F CPVC pipes SDR 11 including plain CPVC SDR 11 new fittings outer dia of pipe 20mm on walls/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Elbow for CPVC pipes outer dia of pipe 16mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Elbow for CPVC pipes outer dia of pipe 20mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Elbow (3/4 X ½) for CPVC pipes outer dia of pipe 20mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass tee for CPVC pipes outer dia of pipe 16mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Tee CPVC pipes outer dia of pipe 20mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Male Threaded Adaptor (MTA/ MBTA) CPVC pipes outer dia of pipe 16mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Male Threaded Adaptor (MTA/ MBTA) CPVC pipes outer dia of pipe 20mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Brass Female Threaded Adaptor (FAT/FBTA) 16 mm in walls/ceiling, floors, in CPVC pipes outer dia of pipe 16mm complete all as specified and directed.

S&F in repair Brass Female Threaded Adaptor (FAT/FBTA) for CPVC pipes outer dia of pipe 20mm on wall/ceiling or in floor complete all as specified and directed.

S&F in repair Tank Adopter for 20mm outer dia CPVC pipes complete all as specified and directed.

S&F in repair union for 16mm outer dia CPVC pipes complete all as specified and directed.

S&F in repair union for 20mm outer dia CPVC pipes complete all as specified and directed.

S&F in repair Ball valve for 16mm outer dia CPVC pipes complete all as specified and directed.

S&F in repair Ball valve for 20mm outer dia CPVC pipes complete all as specified and directed.

S&F in repair ball brass valve high pressure with polyethyelena float and fly nut complete screwed for iron pipe or brass ferrule and fixed 20mm bore dia of pipe complete all as specified and directed.

S&F in repair Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule of 15 mm bore dia complete all as specified and directed.

S&F in repair Stop valves cast copper alloy Chromium plated fancy type long sank concealed type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions of 15 mm bore dia complete all as specified and directed.

S&F in repairs Vitreous china sqatting pan, Orissa pattern , size 580x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including 110mm PVC (SWR) WC connector with lip ring and complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of capacity 10 litre ISI marked complete with inlet ball valve, and handle but excluding brackets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregae) in floor etc complete all as specified and directed.

M&L for 1st quality Non skid coloured ceramic tiles 7 to 8mm thick, joint free (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 1st quality Non skid coloured ceramic tiles 7 to 8mm thick, joint free (square/rectangular joint free) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in riser, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 1st quality glazed ceramic coloured tiles of size 300x200x7 to 8mm thick over on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 1st quality Non skid coloured ceramic tiles 7 to 8mm thick, joint free (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 1st quality Non skid coloured ceramic tiles 7 to 8mm thick, joint free (square/rectangular joint free) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in skirting/ dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for fully vitrified tiles light shade 10 mm thick (square or rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc laid over 15mm thick cement mortar screed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

Dismantling stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L Coloured Chequered cement concrete tiles 200 x 200 x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 20 mm thick Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 18 to 20 mm thick Machine cut kota stone slab flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 15 to 18 mm thick kota stone slab, as in riser of steps, skirting, dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of Kota stone including rubbing and polishing over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

S&F in repairs Stainless steel grade (SS-304) wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs Stainless steel sink with drainage board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x330mm x 160mm complete all as specified and directed.

S&F in repairs PVC connection of size 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

All as per item Ser No 101.00.above but 75mm bore.

S&F PVC (SWR) 110mm bore bends any radius with access door complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 110mm dia complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius with access door complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 75mm dia complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, plane with grating including jointing with solvant cement (Diameter of outlet 75mm) complete all as specified and directed.

Demolition of brick or stone masonry built in cement mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for Brick work with sub class 'B' Old size bricks straight or curved on plan exc 6 m mean radius built in CM 1:4 complete all as specified and directed.

S&F in repair 32mm waste fittings, brass, chromium plated for sinks , basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs 32mm bore low density polyethylene pipes for wash hand basin etc complete all as specified and directed.

M&L for Cutting holes through brick walls built in cement mortar and walls of cement concrete and making good dismantaled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (superficial area not exceeding 150 Sqcm) complete all as specified and directed.

M&L for Cutting holes through brick walls built in cement mortar and walls of cement concrete and making good dismantaled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (superficial area exceeding 150 Sqcm ) but not exceeding 400 Sqcm) complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 in plinth protection with expansion joints 30x10 mm sealed with sealing compound grade 'A' complete all as specified and directed.

M&L for forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in padding/base for bed plates and like complete all as specified and directed.

Complete removal of existing roof treatment in up to depth of original roof slab and removing entire rubbish off the premises, and applying Water proofing treatmnet as under:- (a) Rendering 10mm thick in CM(1:4) mixed with water proofing compound @3% by weight of cement. (b) Applying a coat of approved bituminious primer @0.25 ltr/Sqm and allow to dry. (c) Applying one coat of hot blown bitumen grade 85/[email protected]/Sqm. (d) Supplying and laying polymeric water proofing membrane of weight not less than 3Kg/Sqm (e) Applying a coats of solar reflective bituminious aluminium paint @0.15 kg/sqm over the memberane complete all as specified and directed. Note: WPC shall be measured and paid seperately.

M&L for 40mm thick brick tiles laid over 15mm thick screed bed in CM 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% crude oil by weight of cement complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed.

S&F in repair mild steel work as in framed brakets of angles or tees with web and flanges out to shape, drilled and countersunk for screw, including bending and welding angles as necessary gusset plates, riveting etc n.exc. 10 Kg each bracket conferming to Fe-410 or FE-310-0 complete all as specified and directed.

M&L 25 to 30 mm thick Dholpur stone clading gang saw cut with machine cut edges, uniform colour of each stone size not exceeding 0.25 sqm fixed with and including, making V grove at top at bottom of stone and drilling holes for hold fastener, polishing, rubbing & including silicon treatment laid over 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

Labour only Refastening and securing ends of balusters, newels, rag bolts etc, let into stone and grouted in cement mortar including resecuring the mortices and regrouting in cement mortar complete all as specified and directed.

S&F in repairs door closer aluminium (die cast) body hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 1000 mm in width and of weight 61 to 80 Kgs complete all as specified and directed.

M&L 100mm thick Cement concrete 1:2:4 type B-1, (20mm graded stone aggregate) including necessary form work as path, passages, etc, surface finished even & fair & Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) in plinth protection complete all as specified and directed.

Dismantling stone slab or tile laid in floor, channel, kerb, apron etc. laid dry complete all as specified and directed.

M&L for 60 mm thick Machine pressed precast concrete interlocking paver block with gray cement and no pigment any shape and size confirming to IS 15658-2006, M-35 grade laid in in floors over 25mm thick river sand complete all as specified and directed.

M&L for clean and dry sand filling under floor including spreading, levelling, watering etc complete all as specified and directed.

S&F in repair 15mm bib taps standard of PTMT any colour high pressure screwed for iron pipe and fixed ( minium weight 15mm - 90gms) complete all as specified and directed.

S&F in repair 15mm stop valve of PTMT any colour high pressure screwed for iron pipe and fixed ( minium weight 15mm - 90gms) complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan (Padastal pattern), white (excluding fixing bolt, etc) complete all as specified and directed.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinge device complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white flat back, size 630x450mm excluding pillar tap etc. but including brackets complete all as specified and directed.

S&F in repairs vitreous china urinal half stall type, white complete all as specified and directed.

S&F 40 mm bore low density polyethylene pipe 60cm long of pressure rating 6Kgf/sqm complete all as specified and directed.

S&F in repair pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot and cold with long screwed shanks and fly nuts screwed for iron pipe for 15 mm dia bore complete all as specified and directed.

S&F in repair 15 mm dia pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (Minium weight - 120 gms) complete all as specified and directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 25mm bore weight 455 gms complete all as specified and directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm bore weight 210 gms complete all as specified and directed.

S&F in repair Chromium plated shower rose 125 mm dia with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F grating square 150mm size of PTMT (Minimum weight 100 gms) complete all as specified and directed.

S&F grating doom 150 mm dia with waste hole of PTMT. (Minimum weight 100 gms) complete all as specified and directed.

S&F 32mm waste coupling of PTMT (half or full threaded and minimum weight 45 gms) for urinals complete all as specified and directed.

S&F in repair bottle trap 32 mm bore of PTMT having minium water seal 25 mm and minimum weight 260 gms for wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

M&L for Rotational moulded polyethylene water storage tank 500 litres capacity and fixed (cylindrical vertical with closed top) triple layered, hoisted in position including dismantling old unserviceable water tank complete all as specified and directed.

All as per item Ser No 147.00 above but 1000 litres capacity.

S&F in repairs Health faucet brass, chromium plated with 900mm long PVC connection pipe 15 mm bore with brass sockets complete all as specified and directed.

S&F in repairs Jet spray brass chromium plated with 900mm long PVC connection pipe 15 mm bore with brass sockets for europian water closet complete all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 900mm complete all as specified and directed.

m/s shanti consruction co

Sree Ram Enterprises

Afghani Constructions

M/S RADHEY GOVIND ENTERPRISES

m/s meetu enterprises