REPAIR MAINT OF DG SETS PUMPS MOTORS SUPPLY OF CHEMICALS AND ALLIED WORKS UNDER AGE E M AT GE FAIZABAD

Amount

S & F MCCB 4 pole 100 Amp, 415 volt, 25 kA including taking out of old one complete all as specified. Make : L&T , Havells, Crompton.

S & F On load Change over 4 pole 100 Amp, 415 volt, open execution type, including taking out of old one complete all as specified. Make : L&T , Havells, Crompton.

S & F digital type Voltmeter with LED display suitable for 3 phase with accuracy class 1 in existing panel including taking out of old one complete all as specified. Make : L&T , Nippon , AE.

M & L for 3 pole power contactor 220 volts with 50 Amp AC3 duty rating MNX-50 including auxillary switch of make: L&T , Havells, Crompton, Schneider, Siemens in existing panel including taking out of old one complete all as specified.

M & L for electronic timer for automatic star delta starter 415 volt 50 Hz 3 - 30 sec of make:L&T , Havells, Crompton in existing panel including taking out of old one complete all as specified.

S & F digital type Ammeter with LED display suitable for 3 phase with accuracy class 1 Make: L&T , Nippon, Aein existing panel including taking out of old one complete all as specified.

S & F tape wound ring type Current Transformer suitable for Bar primary of rating 100/5 Amp, burden 5 VA of make: Kappa, Matrix, L&T in existing panel including taking out of old one complete all as specified.

S & F Single phase Preventer Relay with adjustable time delay 30 sec to 5 min suitable for 415 volt AC, SPPR type, Make: L&T , Havells, Crompton including internal wiring from switch gear to relay in existing panel complete all as specified.

S & F Three phase submersible pump controller with single phase preventer of rating 3 phase,415V,50 HZ, 40 HP ,Type MU-G40 FASD, Make : L&T, Sceinider, Havells including taking out of old one complete all as specified.

M&L for fixing of DOL starter three phases 415 Volt for 5 HP electric motor including all fixing materials, complete all as specified.

M&L for fixing of DOL starter three phases 415 Volt for 10 HP electric motor including all fixing materials , complete all as specified.

Supply & Fixing of Flat three core submersible cable PVC insulated and sheathed multistranded copper conductor of cross sectional area 16 sqmm , complete all as specified. Make: Havells , Kalinga ,Polycab .

Supply & fixing LED street light fitting 100W Rectangular LED Flood Light with innovative thermal management and available in multiple optics and equipped with IP66 protection with required connection wire multistand 2.5 Sqmm twin core sheathed weather proof up to ACSR conductor/ Ceiling rose complete all as specified. Make:- Crompton /Bajaj/Philips/Havells .

S&F FR PVC Insulated Single core unsheathed Industrial Flexible cable of size 16 sqmm conforming to IS 694:2010 with bright annealed copper conductor in existing panel including taking out of old one complete all as specified. Make : Polycab / Havells/ Grandley

Supply only bleaching powder in 25 Kg bag (ISI marked) grade II, complete all as specified. (Make: Punjab Alkalies/Modi Alkalies/Sriram ).

Supply only sodium hypochloride liquid (chlorine content 10%) duly packed in sealed drum of make: M/s Declibac/ M/s Rayalshima Enterprise/ Birla Chemicals , complete all as specified.

Collection of water samples of bore wells located in deferent pockets of cantonment area in decontaminated sterilised bottles and testing of water samples for following essential parameters for drinking water as per IS:10500- 2012 from Govt Lab or NABL accredited laboratory: - (i) Colour (ii) odour (iii) taste (iv) pH value, (v) Turbidity (vi) TDS (vii) Total arsenic (viii) Silica (ix) Fluoride (x) Iron (xi) Magnesium (xii) Sulphate (xiii) Total Hardness (xiv) Total alkalinity (xv) Calcium (xvi) Conductivity (xvii) Chloride (xviii) Total Coliform and (xix) E Coli , complete all as specified.

Repair/ Maint of Bleaching Powder doser including replacement of unserviceable parts and thorough cleaning, complete all as specified. [Note: All spares required for repair will be measured and paid under separate item of this schedule as 'Supply only']

Supply only Rubber bladder suitable for 145 ltrs bleaching doser for Bleaching Powder Doser.

All as per item no. 21 but P.P. Funnel suitable for 145 ltrs bleaching doser

All as per item no. 21 but Orifice Plate suitable for 145 ltrs bleaching doser

All as per item no. 21 but Drain Valve suitable for 145 ltrs bleaching doser

All as per item no. 21 but PVC pipe for Solution Dosing Line upto 3.0 mtr suitable for 145 ltrs bleaching doser

All as per item no. 21 but PVC Dose Control Valve suitable for 145 ltrs bleaching doser

All as per item no. 21 but Water Inlet Valve suitable for 145 ltrs bleaching doser

All as per item no. 21 but Solution Outlet Valve suitable for 145 ltrs bleaching doser

All as per item no. 21 but Air release Valve suitable for 145 ltrs bleaching doser

All as per item no. 21 but Solution Feed Valve suitable for 145 ltrs bleaching doser

Supply only Liquid O-Tolidine solution in sealed bottle of 50 ml complete all as specified. Make:- M/s Rankem/ M/s Qualigens .

Supply only Chlorine ppm comparator test Kit with colour indicators having 0.1 to 2.0 PPM with Resolution 0.01 pH, complete all as specified. Make:Avon/ Aquasol

Supply only glass test tube of capacity 10 ml for chlorine check complete all as specified.

Repair and maintenance of of Microprocessor based circuit type water level indicator device LED display fitted in the control panel made of CRCA 16 SWG sheet with chemical grade powder coating to display water level in tank , SS304 grade level sensor pipe fitted in the tank by clamping at the bottom and the top of the tank consist of magnetic float and electronic switch for long life , the pump automatically switch OFF when the wate level in OH tank reaches the maximum level Toggle switch for manual run of pump when tank is full , heavy duty rubber coated wire (approx 100 metre ) for connecting the censor to the tank complete all as specified. Note : The price of the small parts like clamps , nut bolts etc and necessary T&P which is needed for the smooth functioning of Water Level Indicator deemed to be included in the quoted rate .

Supply only Control Cable 1.5 Sqmm X 4 Core copper cable for Microprocessor based circuit

All as per item no. 35 but Magnetic Float Switch vertical/ horizontal type hermetically sealed

All as per item no. 35 but Stainless Steel pressure tube

All as per item no. 35 but Toggle Switch

All as per item no. 35 but Relay

All as per item no. 35 but Electronic Switch

M&L for Rolled mild steel in Joist , channel, angle, or tee sections, fixed independently, without connecting plates, etc. for repair to staircase, hand rails and back rest of over head reservoir or as otherwise directed, complete all as specified. [Note: All T&P and labour charges for working on OH tanks upto 21 mtr high staging deemed to be included in the quoted rate]

Lifting of defective submersible pumping set up to 35 HP capacity from deep well 300mm housing along with connected accessories such as column pipe of 150mm dia appx 30 m submersible cable, steel pipe, spider, sleeve, line shaft, nut, bolts etc complete all as specified and directed by Engr-In-Charge. [Note:- (i) All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate (ii) The Contractor will start the lifting work with in minimum time after getting message verbally/telephonically by JE E/M , AGE E/M. (iii) A penalty of Rs. 500/- per day will be imposed on the Contractor for wilful delay by the Contractor will be imposed as per opinion of Engineer-in-Charge and amount will be deducted from the due payment of the Contractor]

Transportation including loading & unloading of defective submersible pump set 3 phase any make and capacity 25 to 35 HP from pump house to work shop for necessary repair and transporting back to the pump house including carefully loading & unloading of pump set after repair complete all as specified and directed by Engr-In-Charge.

Dismantling of defective submersible pump set any make & model of capacity 25 HP to 35 HP, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair complete all as specified and directed by Engr-In-Charge. [Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate]

Supply only CI/ MS bowl (As per existing size) for submersible pump capacity 25 HP to 35 HP any make & model complete all as specified .

All per item no. 45 but Stainless steel shaft with key

All per item no. 45 but Gun Metal Bush

All per item no. 45 but Stainless steel sleeve.

All per item no. 45 but Sand Guard

All per item no. 45 but Impeller lock with key

All per item no. 45 but Neck ring (as per existing size and type)

All per item no. 45 but Turning & polishing of Pump shaft (lathe work)

Supply only Stainless Steel thrust bearing. parts for submersible motor of capacity 25 HP to 35 HP any make & model complete all as specified .

All per item no. 53 but Carbon plate.

All per item no. 53 Gun Metal bush

All per item no. 53 Rubber bush

All per item no. 53 Upper housing

All per item no. 53 Lower Housing

All per item no. 53 Turning, polishing of Rotor & shaft (Lathe work)

M&L Rewinding of submersible motor capacity 25 HP to 35 HP any make & model with super enamelled copper wire of existing size including removal of existing burnt winding, cleaning of slots including packing material, connection and testing complete all as specified.

M&L for painting to pump set with two coat of synthetic enamel paint (grey colour) over a coat of red oxide primer after preparation of surface complete all as specified.

Lowering, connecting, commissioning testing of repaired submersible set any make and capacity 25 HP to 35 HP 3 phase 415V into bore well 300/200mm with connected items such as column pipe approx 40 RM, properly connecting submersible cable etc complete all as specified. [Note:- (i) All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate (ii) The Contractor will start the lifting work with in minimum time after getting message verbally/ telephonically by JE E/M/ AGE E/M. (iii) A penalty of Rs. 500/- per day will be imposed on the Contractor for wilful delay by the Contractor will be imposed as per opinion of Engineer-in-Charge and amount will be deducted from the due payment of the Contractor]

Complete servicing of Fire fighting pump set any make & model of capacity 60 HP including replacement of minor spares and testing after servicing complete all as specified. [Note: (i) Greasing of moving parts deemed to be included in the quoted rate (ii) All type of T&P main switch ,electric multi meter/ tong tester for fault detecting , etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

Supply only rubber packing 6mm thick consisting of 8/6" holes for 100mm to 150 mm dia column pipe complete all as specified.

M&L for Rewinding of 2-2.5 HP motor 3 phase 415 volt 50 Hz AC,with super enamelled copper winding wire complete all as specified.

Dismantling of defective Monoblock motor pump any make & model of capacity 2 -2.5 HP, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair complete all as specified . [Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate]

Supply only Motor Bearing for monoblock pump capacity 2-2.5 HP any make & model complete all as specified.

All as per item no. 67 but Gland packing

All as per item no. 67 but Packing paper

All as per item no. 67 but Water seal

All as per item no. 67 but Starting Coil

All as per item no. 67 but Motor housing & sleeve repairing on Lathe

All as per item no. 67 but Impeller Brass

M&L for Rewinding of 5 HP motor 3 phase 415 volt 50 Hz AC, complete all as specified.

Dismantling of defective Monoblock motor pump any make & model of capacity 5 HP, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair ,complete all as specified. [Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate]

Supply only Motor bearing for monoblock pump capacity 5 HP any make & model complete all as specified .

All as per item no. 76 but Gland packing

All as per item no. 76 but Packing paper

All as per item no. 76 but Water seal

All as per item no. 76 but Starting Coil

All as per item no. 76 but Motor housing & sleeve repairing on Lathe

All as per item no. 76 but Impeller Brass

M&L for Rewinding of 10 HP motor 3 phase 415 volt 50 Hz AC, with super enamelled copper winding wire , complete all specified.

Dismantling of defective Monoblock motor pump any make & model of capacity 10 HP, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair complete all as specified . [Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate]

Supply only Motor bearing for monoblock pump capacity 10 HP any make & model complete all as specified.

All as per item Ser No 85 but Gland packing

All as per item Ser No 85 but Packing paper

All as per item Ser No 85 but Water seal

All as per item Ser No 85 but Starting Coil

All as per item Ser No 85 but Motor housing & sleeve repairing on Lathe

All as per item Ser No 85 but Impeller Brass

Periodical maintenance including complete servicing of Diesel Engine Generator set of 160 KVA capacity at Military Hospital of make: Kirloskar or any other make and connected accessories including replacement of oil /lubricant filter to keep the plant in running condition including routine maintenance complete all as specified and as directed. [Note: (i) The Contractor need to get the job done through authorised service centre/ agency of Kirloskar Oil Engine Ltd or any other OEM (Original Equipment Manufacturer) located near Faizabad. The cost thereof deemed to be included in the quoted rate. (ii) All Spare parts for routine maintenence will be measured and paid seperately under relevent items of this schedule as 'Supply Only' (iii) Labour charges for routine maintenance including properly dismantling of old parts deemed to be included in the quoted rate]

All as per item Ser No 92 here-in-before but of Diesel Engine Generator Set of 62.5/ 63 kVA capacity at Pump House No 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, STP Himachal Niwas, STP Kandahar Line, Signal Centre, Amn Dump, Trolly Mounted

All as per item Ser No 92 here-in-before but of Diesel Engine Generator Set of 40 kVA capacity at Records

All as per item Ser No 92 here-in-before but of Diesel Engine Generator Set of 15 kVA capacity at Stn HQ

Supply only Cut out for routine maintenance of Alternator of DG Set 160 KVA, complete all specified.

All as per item no. 96 but Rectifier Assembly

All as per item no. 96 but Brush Box Assembly

All as per item no. 96 but Bearing

All as per item no. 96 but Oil seal

All as per item no. 96 but Field Coil

All as per item no. 96 but Lubricant oil filter for DG set 160 KVA

All as per item no. 96 but Fuel filter (Pre) for DG set 160 KVA

All as per item no. 96 but Fuel filter (Micro) for DG set 160 KVA

All as per item no. 96 butAir filter for DG set 160 KVA

All as per item no. 96 but Hose : Water Pump inlet to Radiator outlet for DG set 160 KVA

All as per item no. 96 but Hose :Pipe to Water Pump for DG set 160 KVA

All as per item no. 96 but Hose : Pipe to Diesal tank for DG set 160 KVA

All as per item no. 96 but Hose pipe clip with nut

All as per item no. 96 but Terminal block for DG set 160 KVA

Supply only cut out for routine maintenance of Alternator of DG Set 15-62.5 KVA.

All as per item no. 111 but Rectifier Assembly

All as per item no. 111 but Brush Box Assembly

All as per item no. 111 but Bearing

All as per item no. 111 but Oil seal

All as per item no. 111 but Field Coil

All as per item no. 111 but Lubricant oil filter

All as per item no. 111 but Fuel filter (Pre)

All as per item no. 111 but Fuel filter (Micro)

All as per item no. 111 but Air filter

All as per item no. 111 but Hose : Water Pump inlet to Radiator outlet

All as per item no. 111 but Hose :Pipe to Water Pump

All as per item no. 111 but Hose : Pipe to Diesal tank

All as per item no. 111 but Hose pipe clip with nut

All as per item no. 111 but Terminal block

Supply only Coolant for DG Set , , complete all specified.

Supply only Lub Oil for DG Set of make Koel Care Premium Genuine

Supply only lead acid battery 12 volt 180 Ah including initial charge of make: Exide , Amaron, Luminous, complete all specified.

M&L for Automatic Voltage Regulator for DG Set of capacity 15 to 62.5/ 63 kVA make: Kirloskar or equivalent as approved by GE including taking out of old one, complete all specified.

M&L for Automatic Voltage Regulator for DG Set of capacity 160 kVA make: Kirloskar or equivalent as approved by GE including taking out of old one, complete all specified.

M&L for Calibration of Fuel Injection Pump including properly dismantling and transporting to service center/workshop for over hauling/ calibration and refixing on DG Set after calibration for DG Sets of capacity 160 kVA including taking out of old one and with replacement of following items, complete all specified. a) Element - 06 Nos b) D.V - 06 Nos c) T.R.B - 06 Nos d) Bearing - 02 Nos e) C.R - 01 Nos f) C.R Bush - 02 Nos g) Ball Bearing - 01 Nos h) F.P.P - 01 Nos i) F.P Kit - 01 Nos j) Pressure Bolt - 06 Nos k)Nozzle seal - 02 Nos l) Nozzle setting - 06 Nos & with all other neessary items .

All as per item 131 above but for DG Sets of capacity 62.5/ 63 kVA

All as per item 131 above but for DG Sets of capacity 40 kVA

All as per item 131 above but for DG Sets of capacity 15 kVA

M&L for Banjo Bolt M 14 x 1.5 including taking out of old one , complete all specified.

M&L for Flexible fuel pipe type 7.5 14 x 14 B 700 PB of make: Kirloskar or equivalent as approved by GE including taking out of old one, complete all specified.

M&L for Expansion bellow suitable for 62.5 kVA DG Set of make: Kirloskar including as approved by GE taking out of old one, complete all specified.

M&L for Starter Ring suitable for 160 kVA DG Set of make: Kirloskar or equivalent as approved by GE including taking out of old one, complete all specified.

M&L for Starter Ring suitable for 15 to 62.5 KVA DG Set of make: Kirloskar or equivalent as approved by GE including taking out of old one , complete all specified.

M&L for Fuel Pump mounted STOP solenoid switch suitable for 15 to 62.5-63 kVA DG set of make: Kirloskar or equivalent as approved by GE including taking out of old one , complete all specified.

M&L for Fan Belt suitable for 62.5 kVA DG set of make: Kirloskar or equivalent as approved by GE including taking out of old one , complete all specified.

M&L for servicing of radiator including cleaning and testing of leakages for DG set of capacity 15-62.5 KVA , complete all specified. [Note: - In case of leakages found during servicing, the same should be measured and paid separately ]

Dismantling the radiator and transporting to workshop, repair of all leakage and transporting back and refitting in original position and testing for DG set of capacity 15-62.5 KVA , complete all specified.

M&L for Carefully dismantling the fuel tank and transporting to workshop, repair of all leakage, cleaning and transporting back and refitting in original position and testing after completion for DG set of capacity 62.5/ 63 kVA all as specified and as directed including taking out of old one, complete all specified.

M&L for Carefully cleaning of fuel tank for DG set of capacity 62.5/ 63 kVA all as specified and as directed including taking out of old one, complete all specified.

M&L for Carefully dismantling the self starter of DG set capacity 15-62.5 KVA and transporting to workshop and reffiting back after repair with replacement / repair of material required for repairing , complete all specified.

Supply only Carbon bush with spring materials for repair of self starter , complete all specified.

All as per item Ser No 147 above but GM bush set

All as per item Ser No 147 above but Bendex Pinion

AlAll as per item Ser No 147 above but Solenoid switch

All as per item Ser No 147 above but Armature Rewinding

All as per item Ser No 147 above but Field coil Set.

M&L for rectification of leakage from 50mm bore GI Pipe line joints including excavation, returning and filling etc incl fittings like unions, sockets, bends, elbows, tees, nipples etc as required complete all as specified .

All as per item Ser No 153 above but 40mm bore

All as per item Ser No 153 above but 25mm bore

All as per item Ser No 153 above but 20mm bore

All as per item Ser No 153 above but 15mm bore

S&F 15mm bore Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of make : Zolotov ,Leader, Venus , complete all specified.

All as per item Ser No 158 above but 20mm bore

All as per item Ser No 158 above but 25mm bore

All as per item Ser No 158 above but 40mm bore

All as per item Ser No 158 above but 50mm bore

S&F connection & testing 80mm bore sluice valve 'ISI marked' both ends flanged and drilled cast iron body class PN-1.6 conforming to IS-14846/2000 complete with gun metal spindle of make : BIR, Upadhyaya, Leader, Kartar or equivalent including necessary nut bolts and gasket etc for fixing complete all as specified including taking down existing. [Note: For sluice valves fixed with pillars of over head tank, breaking of RCC/lead/ flange joints and repairing the same after fixing of valve deemed to be included in the quoted rates]

All as per item Ser No 163 above but 100mm bore

All as per item Ser No 163 above but 150mm bore

M&L for rectification of leakage from 150mm bore CI Pipe line of joints incl excavation in mud/soil and coucking with pig lead , returning filling , complete all specified.

All as per item Ser No 166 above but 100mm bore

All as per item Ser No 166 above but 80mm bore

M&L Earthing complete with galvanised steel earth plate electrode 600 X 600 X 6mm thick buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the earth plate not less than 1.5 meters deep below normal ground level, connected with and including galvanised iron strip of size 25 x 4mm connected to main test point as directed as earthing lead by means of nuts, bolts and washers of galvanised iron protected by 40mm dia (medium grade) GI tubing, funnel, wire mesh, 20mm bore GI tubing (light grade) watering pipe, including concrete pit in PCC (1:3:6) type C-1, precast RCC (1:2:4) type B-1 cover slab of size 350 x 350 x 50mm reinforced with 8mm dia TMT bars @ 15cm c/c in both ways and 10mm dia MS handle (01 No) of suitable size for lifting of cover slab, charcoal and salt in alternate layers including necessary excavation and earth work in soft/loose soil all as shown in Electric plate No 3 of SSR Part-I and testing on completion complete all as specified .

M&L for replacing of gland packing,nut-bolts and washer of 80mm bore sluice valve , complete all specified.

All as per item Ser No 170 above but 100mm bore

All as per item Ser No 170 above but 150mm bore

M&L for replacing of gun metal check nut of 80mm bore sluice valve , complete all specified.

All as per item Ser No 173 above but 100mm bore

All as per item Ser No 173 above but 150mm bore

M&L for replacing of existing size brass spindle of 80mm bore sluice valve , complete all specified.

All as per item Ser No 176 above but 100mm bore

All as per item Ser No 176 above but 150mm bore

S&F Long 'ISI marked' for iron pipe all as per latest IS specifications of size 15mm bore , complete all specified.

All as per item Ser No 179 above but 20mm bore

All as per item Ser No 179 above but 25mm bore

S&F Nipple of length 6'' 'ISI marked' for15mm bore iron pipe all as per latest IS specifications , complete all specified.

All as per item Ser No 182 above but 20mm bore

All as per item Ser No 182 above but 25mm bore

All as per item Ser No 182 above but 40mm bore

All as per item Ser No 182 above but 50mm bore

S&F Nipple of length 4'' 'ISI marked' for 15mm iron pipe all as per latest IS specifications, complete all specified.

All as per item Ser No 187 above but 20mm bore

All as per item Ser No 187 above but 25mm bore

All as per item Ser No 187 above but 40mm bore

All as per item Ser No 187 above but 50mm bore

S&F Union 'ISI marked' for 20mm bore iron pipe all as per latest IS specifications , complete all specified.

All as per item Ser No 192 above but 25mm bore

All as per item Ser No 192 above but 40mm bore

All as per item Ser No 192 above but 50mm bore

S&F Long 'ISI marked' for 15mm iron pipe all as per latest IS specifications, complete all specified..

All as per item Ser No 196 above but 20mm bore

All as per item Ser No 196 above but 40mm bore

All as per item Ser No 196 above but 50mm bore

S&F Pluck 'ISI marked' for 15mm bore iron pipe all as per latest IS specifications, complete all specified.

All as per item Ser No 200 above but 20mm bore

All as per item Ser No 200 above but 25mm bore

S&F Elbow 'ISI marked' for 15mm bore iron pipe all as per latest IS specifications , complete all specified.

All as per item Ser No 204 above but 20mm bore

S&F 'Tee' of size 20mm 'ISI marked' for iron pipe all as per latest IS specifications, complete all specified.

S&F Reducer of size 15x20 mm 'ISI marked' for iron pipe all as per latest IS specifications, complete all specified.

Taking out steel water tubing UPVC for 15 mm bore size including fittings complete all as specified .

S&F Unplasticised PVC pipes Sch 40 of fixed complete to walls, ceilings or in floors etc., any type of pipe for 15 mm bore sizes , complete all specified.

Repair and maintenance of suction sweeper comprising 600mm long MS/ CI fabricated suction head with PVC wheels, spring loaded brush and fibber squeezer including trolley mounted electric driven non clog self priming type centrifugal pumping set with 02 HP Motor 03 phase , 415 V electric driven DOL Push button starter along with repair to minor defects such as repair/ replacement to electric contact, kit-kat fuse, pumping set gland rope, coupling nuts & bolts, bush/ thrust bearing of existing size , push button, contactor block & relay of starter ,oiling/ greasing and testing etc complete including painting with two coat of synthetic enamel paint -of existing colour after removal of old paint / cleaning to rusted/ corrosive portion - 04 Sets [Note:- (i) All type of T&P main switch ,electric multi meter/ tong tester for fault detecting , etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate. (ii) If item of work is not got executed for any of the suction sweeper-machine , price adjustment shall be made based on the proportional rate worked out from unit quoted rate for the item of work. (iii) Supply of major items required for repair/replacement shall be measured and paid separately under relevant item of this schedule as 'supply only']

Supply only following Nylon-Rope size (14 -20) mm dia suction sweeper , complete all specified.

All as per item Ser No 210 above but Spire Brush suitable for Cleaning of swimming pool, complete all specified.

S & F PVC wheel with bush and nut bolt set of 04 nos suitable for suction sweeper machine , complete all specified.

Supply and fixing PVC Floats suitable for Swimming pool including taking out of old one, complete all specified.

Super Automobiles

M/S Shiv Ballabh Mishra

M/S ATUL CONSTRUCTION

Hi-Tech Constructions

Stoneage

M/S A P CONSTRUCTION

Shivagya Engineering