Annual repair to Non Residential building in Commissioner Camp office at Karnal in Karnal Distt. For the year 2020-21

Amount

Tile terracing with one layer of tiles, 22.86 cm x 11.43 cm x 3.81cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean (HSR 13.14).

conglomerate floor 40 mm thick cement concrete topping 1:2:4 (HSR 14.9)

extra for laying terrazzo flooring on stair case treads not exceeding 30 cm in width including nosing (HSR 14.42)

Fixing and Laying of Marble stone flooring 17mm thick slab including matching grains of marble laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry, mixed with pigment to match the shade of marble incluidng rubbing and polishing (excluding the cost of Marble, Marble will be supplied by the Department) [HSR 14.49]

Kotah stone flooring, 25mm thick, in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing (HSR 14.62)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK. (HSR 14.89)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) a) Size of ceramic Glazed tiles 200 x 300 mm

6 mm thick cement plaster 1 : 3 on walls ( HSR 15.1 )

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

12 mm thick cement plaster 1:5 on walls (HSR 15.6)

12 mm thick cement plaster 1:6 on walls [HSR 15.7]

15 mm thick cement plaster 1:6 on rough side of single or half brick wall (HSR 15.12)

10 mm thick cement plaster 1:4 on under side of ceiling (HSR 15.52)

Lime Surkhi pointing 2:3 weathered and struck on brick and tile work. [HSR 15.59]

Cement pointing 1:3 deep variety on brick and tile work. (HSR 15.61)

Cement pointing flush 1:3 on stone walls (HSR 15.66)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3).

Painting two coats with synthetic enamel paint in all shades on old wood-work or metalic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Painting one coat with readymixed paint in all shades on old wood work to give an even shade including rubbing down old paint. [HSR 16.8]

Painting one coat coat with plastic emulsion paint on walls on old work to give an even shade. (HSR 16.31)

Distempering with washable oil bound distemper (of approved manufacture) two coat on old distempered work (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint (1st. Quality) [HSR 16.79 (b)]

Sawing of hard wood like teak, kikar, sal & shisham etc, by band -saw including carriage to and from saw mill. (HSR 17.2) LR

Sawing timber at site of work by manual labour- (HSR 17.3) L.R

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. ( Non coniferous timber other than teak, conforming to I.S. specification No. 1003 kiln seasoned )- ( c) 4 mm thick ( glazing area above 55 sq dm but upto 84 sq dm of each pane) [HSR 17.36( c)]

Supplying and fixing glass panes with teak wood moulding (HSR 17.42 (c ) 4 mm thick (glazing area above 55 sq dm. but upto 84 sq dm of each pane)

Structural steel work in angles, tees and flats, rivetted including cutting fixing all gusset plates, bolts, nuts, rivets etc., with hoisting and erecting in position for roof trusses, well kerbs, plates and trussed girders, etc., of any span for building and bridges. [HSR 18.3]

Providing and fixing in position best indian make (to the approval of the Engineer-in-Charge) European type water closet suit with non-concealed 'P' or 'S' trap with or without vent and all other necessary fittings as fully described in item no. 30.3 above [HSR 30.4 (i)]

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos. chromium plated brass screws and washers complete including cutting and making good the walls etc. [HSR 30.71] a) Indian make (i) 600 x 450mm

Providing and fixing in position 15mm i/d C.P.bras bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] a) bib cock long body

c) Bib cock

Providing and fixing in position C.P.brass stop cock (as approved by the Engineer-in-charge) [HSR 30.76] a0 15mm stop cock (ii) Concealed stop cock with flange

Bani Constructions