ADB AMR-05

Amount

Upgradation of SH 292 TO DURGWADA Road Tq. MORSHI Dist-Amravati

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.(Item No. 3.30/ P.No. 12)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 16)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 15 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 16 A with a lead upto 1000 m

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 16 A with a lead upto 1000 m

Construction of Hard Shoulders as per Technical Specification Clause 407 (Item No. 4.10 (A) and B / P.No. 26)

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material by manual means. . (Item No. 9.1 / P.No.39 )

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Watering and compacting the Embakment formed of material obtained from the road cutting departmental land or other soures within in a lead of 50 mafter after laying them layers of 20 cm to 30 cm with 3% camber and design superelevation etc.complete( compaction with power roller )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.21)

Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 25)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 30 )

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20to 0.25 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. ( Item No. 5.2 (ii) / P. No. 29)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 (B) By Mechanical Means with paver finisher Case - II : Type B (I) Bitumen (S-65) VG-30 (Item No. 5.9 - A II (I) / P.No. 32 )

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302(Item No. 14.4 / P.No.57 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 48 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 . ( II )P.C.C grade M 15 (I) Nominal mix (1:2.5:5) (Item No. 11.4 (I) (ii) / P.No. 48 )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-15 (i) Nominal Mix 1:2.5:5 ) (Item No. 12.2 (I) (i) / P.No. 50 ) )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-20 (Item No. 12.2 (I) (i) / P.No. 50 ) )

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 51)

Providing Tar paper bearing of approved quality in proper size etc. complete (Rate as per PWD CSR 2017-18) (Item No.13.16 (V) / P.No. 55 )

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications M25 garde Clauses 800, 1205.4 and 1205.5 II R.C.C M 25 (Item No. 13.1 (II) / P.No. 53 )

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 i) Granular Material (Item No. 12.8 (I) / P.No. 51 )

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301 ) [Spec.No. :- Item no. 14.1 ]

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs B)Semi Reflective Traffic Signs Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 ii)600 mm equilateral triangle

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm X 450 mm rectangular ]

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) ii) Ordinary Km. Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 40)

Construction of Rounded Hump Type Speed Breaker as per IRC : 99 (1988) for general traffic as per specification, including painting, fixing cautionery boards etc. complete and as directed by Engineer-in-Charge.

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro- reflectance of the reflecting panel, to the Engineer. (pwd ssr ITEM 6.09)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Upgradation Of Kolvihir to brhamnwada Road Tq. Morshi Dist-Amravati

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.(Item No. 3.30/ P.No. 12)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 16)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 15 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 16 A with a lead upto 1000 m

Construction of Subgrade and earthen shoulders with approved material obtained from barrow pits with all lifts and leads,transprting to site,spreding grading to rtequired slope and comapcted to meet the requirment of tabel 300.2 with lead upto1000 m as per technical specification clause 303.1(Item No 3.14/P.No 15 )

Construction of Hard Shoulders as per Technical Specification Clause 407 (Item No. 4.10 (A) and B / P.No. 26)

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material by manual means. . (Item No. 9.1 / P.No.39 )

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Watering and compacting the Embakment formed of material obtained from the road cutting departmental land or other soures within in a lead of 50 mafter after laying them layers of 20 cm to 30 cm with 3% camber and design superelevation etc.complete( compaction with power roller )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.21)

Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 25)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 30 )

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 29)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 (B) By Mechanical Means with paver finisher Case - II : Type B (I) Bitumen (S-65) VG-30 (Item No. 5.9 - A II (I) / P.No. 32 )

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.4 B / P.No. 39 )

Filling in foundation trenches as per drawing and technical specification Clause 305.3.9.I Sand filling

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 (II) Rubble filling (For B.C. Soil) (Item No. 11.2 (II)/ P.No. 47 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 48 )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-15 (i) Nominal Mix 1:2.5:5 ) (Item No. 12.2 (I) (i) / P.No. 50 ) )

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 51)

Plain/reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (III) R.C.C grade M 20 (Item No. 12.2 (III/ P.No. 50 ) M20 cap

Providing Tar paper bearing of approved quality in proper size etc. complete (Rate as per PWD CSR 2017-18) (Item No.13.16 (V) / P.No. 55 )

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications M25 garde Clauses 800, 1205.4 and 1205.5 II R.C.C M 25 (Item No. 13.1 (II) / P.No. 53 )

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 i) Granular Material (Item No. 12.8 (I) / P.No. 51 )

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301 ) [Spec.No. :- Item no. 14.1 ]

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 39 )

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs B)Semi Reflective Traffic Signs Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 ii)600 mm equilateral triangle

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm X 450 mm rectangular ]

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) ii) Ordinary Km. Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 40)

Construction of Rounded Hump Type Speed Breaker as per IRC : 99 (1988) for general traffic as per specification, including painting, fixing cautionery boards etc. complete and as directed by Engineer-in-Charge.

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro- reflectance of the reflecting panel, to the Engineer. (pwd ssr ITEM 6.09)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Upgradation of MAYAWADI APPROACH road Tq MORSHI, Dist Amravati

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.(Item No. 3.30/ P.No. 12)

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 16)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 15 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 16 A with a lead upto 1000 m

Construction of Subgrade and earthen shoulders with approved material obtained from barrow pits with all lifts and leads,transprting to site,spreding grading to rtequired slope and comapcted to meet the requirment of tabel 300.2 with lead upto1000 m as per technical specification clause 303.1(Item No 3.14/P.No 15 )

Construction of Hard Shoulders as per Technical Specification Clause 407 (Item No. 4.10 (A) and B / P.No. 26)

Dismantling Stone Masonry as per Technical Specification Clause 202. Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of stone masonry, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per Technical Specification Clause 202. (Item No. 2.7 (C) / P.No. 8) Stone masonary

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202. B )Above 600 mm to 900 mm dia Hume pipe (Item No. 2.7 / P.No. 12 )

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantalling of Masnory Works as per Technical Specification Clause 202 C) Above 900mm Ø Hume Pipe (Item No. 2.7 / P.No. 12 )

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material by manual means. . (Item No. 9.1 / P.No.39 )

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.21)

Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 25)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 30 )

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. ( Item No. 5.2 (ii) / P. No. 29)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 (B) By Mechanical Means with paver finisher Case - II : Type B (I) Bitumen (S-65) VG-30 (Item No. 5.9 - A II (I) / P.No. 32 )

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and Laying Reinforced Cement Concrete Pipe NP2 as per design.Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. For 600 mm dia.

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 (II) Rubble filling (For B.C. Soil) (Item No. 11.2 (II)/ P.No. 47 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 48 )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-15 (i) Nominal Mix 1:2.5:5 ) (Item No. 12.2 (I) (i) / P.No. 50 ) )

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 51)

Plain/reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (III) R.C.C grade M 20 (Item No. 12.2 (III/ P.No. 50 ) M20 cap

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 i) Granular Material (Item No. 12.8 (I) / P.No. 51 )

Providing 90 cm thick flexible stone Mat as per Standard drawing including supplyying all materials at work site spreading and compaction etc complete ( Spec No : As directed by Engineer incharge )

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 39 )

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs B)Semi Reflective Traffic Signs Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 ii)600 mm equilateral triangle

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm X 450 mm rectangular ]

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) ii) Ordinary Km. Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade BOUNDRY PILLAR/LOCAL STONE (Precast) of standard design as per IRC:25fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1704. (I.No. 10.11 / P.No. 40) iii) 200m Stone

Construction of Rounded Hump Type Speed Breaker as per IRC : 99 (1988) for general traffic as per specification, including painting, fixing cautionery boards etc. complete and as directed by Engineer-in-Charge.

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro- reflectance of the reflecting panel, to the Engineer. (pwd ssr ITEM 6.09)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Upgradation of RIDHPUR TO BRHAMANWADA ROAD oad Tq MORSHI, Dist Amravati

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.(Item No. 3.30/ P.No. 12)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 16)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 15 ]

Construction of Subgrade and earthen shoulders with approved material obtained from barrow pits with all lifts and leads,transprting to site,spreding grading to rtequired slope and comapcted to meet the requirment of tabel 300.2 with lead upto1000 m as per technical specification clause 303.1(Item No 3.14/P.No 15 )

Construction of Hard Shoulders as per Technical Specification Clause 407 (Item No. 4.10 (A) and B / P.No. 26)

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material by manual means. . (Item No. 9.1 / P.No.39 )

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Watering and compacting the Embakment formed of material obtained from the road cutting departmental land or other soures within in a lead of 50 mafter after laying them layers of 20 cm to 30 cm with 3% camber and design superelevation etc.complete( compaction with power roller )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.21)

Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 25)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 30 )

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 29)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 (B) By Mechanical Means with paver finisher Case - II : Type B (I) Bitumen (S-65) VG-30 (Item No. 5.9 - A II (I) / P.No. 32 )

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and Laying Reinforced Cement Concrete Pipe NP2 as per design.Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. For 800 mm dia.

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302(Item No. 14.4 / P.No.57 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 48 )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-15 (i) Nominal Mix 1:2.5:5 ) (Item No. 12.2 (I) (i) / P.No. 50 ) )

Plain/reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (III) R.C.C grade M 20 (Item No. 12.2 (III/ P.No. 50 ) M20 cap

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 i) Granular Material (Item No. 12.8 (I) / P.No. 51 )

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301 ) [Spec.No. :- Item no. 14.1 ]

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 39 )

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs B)Semi Reflective Traffic Signs Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 ii)600 mm equilateral triangle

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm X 450 mm rectangular ]

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) ii) Ordinary Km. Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 40)

Construction of Rounded Hump Type Speed Breaker as per IRC : 99 (1988) for general traffic as per specification, including painting, fixing cautionery boards etc. complete and as directed by Engineer-in-Charge.

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro- reflectance of the reflecting panel, to the Engineer. (pwd ssr ITEM 6.09)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Upgradation of MOLVAN APPROCH road Tq Morshi, Dist Amravati

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 16)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 15 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 16 A with a lead upto 1000 m

Construction of Subgrade and earthen shoulders with approved material obtained from barrow pits with all lifts and leads,transprting to site,spreding grading to rtequired slope and comapcted to meet the requirment of tabel 300.2 with lead upto1000 m as per technical specification clause 303.1(Item No 3.14/P.No 15 )

Construction of Hard Shoulders as per Technical Specification Clause 407 (Item No. 4.10 (A) and B / P.No. 26)

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material by manual means. . (Item No. 9.1 / P.No.39 )

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Watering and compacting the Embakment formed of material obtained from the road cutting departmental land or other soures within in a lead of 50 mafter after laying them layers of 20 cm to 30 cm with 3% camber and design superelevation etc.complete( compaction with power roller )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.21)

Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 25)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 30 )

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. ( Item No. 5.2 (ii) / P. No. 29)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 (B) By Mechanical Means with paver finisher Case - II : Type B (I) Bitumen (S-65) VG-30 (Item No. 5.9 - A II (I) / P.No. 32 )

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and Laying Reinforced Cement Concrete Pipe NP2 as per design.Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. For 600 mm dia.

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302(Item No. 14.4 / P.No.57 )

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 (II) Rubble filling (For B.C. Soil) (Item No. 11.2 (II)/ P.No. 47 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 48 )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 . ( II )P.C.C grade M 15 (I) Nominal mix (1:2.5:5) (Item No. 11.4 (I) (ii) / P.No. 48 )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-15 (i) Nominal Mix 1:2.5:5 ) (Item No. 12.2 (I) (i) / P.No. 50 ) )

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-20 (Item No. 12.2 (I) (i) / P.No. 50 ) )

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 51)

Plain/reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (III) R.C.C grade M 20 (Item No. 12.2 (III/ P.No. 50 ) M20 cap

Providing Tar paper bearing of approved quality in proper size etc. complete (Rate as per PWD CSR 2017-18) (Item No.13.16 (V) / P.No. 55 )

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications M25 garde Clauses 800, 1205.4 and 1205.5 II R.C.C M 25 (Item No. 13.1 (II) / P.No. 53 )

Supplying, fitting and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 i) Granular Material (Item No. 12.8 (I) / P.No. 51 )

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301 ) [Spec.No. :- Item no. 14.1 ]

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 39 )

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs B)Semi Reflective Traffic Signs Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 ii)600 mm equilateral triangle

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm X 450 mm rectangular ]

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) ii) Ordinary Km. Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 40)

Construction of Rounded Hump Type Speed Breaker as per IRC : 99 (1988) for general traffic as per specification, including painting, fixing cautionery boards etc. complete and as directed by Engineer-in-Charge.

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro- reflectance of the reflecting panel, to the Engineer. (pwd ssr ITEM 6.09)