Special repair to conversion of LT OH to UG cable, switch gear pnels and certain revenue works at Jaipur Mil Stn under GE south Jaipur

Amount

02/SR/61SA/QW/20-21 Excavation in trenches n.exc 1.5metre wide and n.exc 1.5 metre in depth for foundation etc or for laying of cable etc and getting out in soft/loose soil 02/SR-378, 12/SR-391, 06/Rev-60

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm in depth. 02/SR-216, 12/SR-272, 06/Rev-34

Removing of excavated material (soil) to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.50metre above the starting point 02/SR-162,12/SR-119, 06/Rev-26

M & L Sand cushioning to PVC under ground cable with tibba sand and punning to provide a required cover. 02/SR-113, 12/SR-110, 06/Rev-18

M & L Bricks for protection cover to under ground cable (with old size sub class ‘B’ bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10mm as directed by Engineer-in-Charge. 02/SR-11.5, 12/SR-11.0, 06/Rev-1.9

Supply, install, commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming (a) ACB 630 amps, fixed type manual 4 pole, 50Hz ,415 V with rupturing capacity 50 KA-01 No, Make :- L&T, Legrand, Scheineiders. (b) Bus bar electrolytic grade copper 1000Amp,4 pole, not less than 1.5 Mtr long SMC insulators mounted on insulators - 01 set Outgoing (a) MCCB 320 amps, 4 pole, 35/36 KA , with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make :- L&T,Legrand, Scheineiders (b) MCCB 200 amps, 4 pole,35/36 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 2 Nos. Make :- L&T,Legrand, Scheineiders (c) MCCB 160 amps, 4 pole,35/36 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 2 Nos. Make :- L&T,Legrand, Scheineiders. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands.

All as per tems No -06 above but having the accessories of following capacity for Incoming (a) MCCB 320 amps, 4 pole, 50Hz ,415 V with rupturing capacity 35/36 KA-01 No Make :- L&T, Legrand, Scheineiders/C&S. (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 600Amp,4 pole, not less than 75 cm long mounted on insulators 01 set Outgoing (a) MCCB 160 amps, 4 pole,25 KA with adjustable thermal over load release with earth fault protection. 50 Hz, 415 volts grade - 3 Nos. Make :- L&T, Legrand, Scheineiders/C&S. (b) Blank Space for 3 phace meter - 01 Nos Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands

All as per tems No -06 above but having the accessories of following capacity Incoming (a) MCCB 100 amps, 4 pole, 50Hz ,415 V with rupturing capacity 25 KA-01 No Make :- L&T, Legrand, Scheineiders. Outgoing (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200 Amp, 4 pole, not less than 50cm long mounted on insulators 01 set Note (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands.

Supplying, laying, Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade, of size following sizes :-

50 sqmm, 3 1/2 core 02/SR-220, 12/SR-320

16 sqmm, 4 core 02/SR-525, 12/SR-515, 06/Rev-210

120 Sqmm 3.5 Core (12/SR)

Laying only under mentioned XLPE Cables in trench, wall on pole. (Note:LT cable shall be issued under Sch 'B' as free for laying only)

240 sqmm, 3 1/2 core

185 sqmm, 3 1/2 core

70 sqmm, 3 1/2 core 02/SR-380, 12/SR-130

35 Sqmm 3.5 Core 02/SR-210, 12/SR-150, 06/Rev-140

25 sqmm, 4 core 02/SR-200, 12/SR-350

95 Sqmm 3.5 Core (12/SR)

10 Sqmm 2 Core (12/SR)

Dismantling old existing ACSR conductor of any type/size for reuse or to be diposite to MES store yard all as directed by Engr-in-Charge. 02/SR -0.80, 12/SR-0.40

Dismantling old existing MS cross arms of any type/shape. 02/SR-0.60, 12/SR-0.50

Dismantling old existing Insulators of any type/shape for reuse or to be diposite to MES store yard all as directed by Engr-in-Charge. 02/SR-36, 12/SR-48

Dismantling of prestressed cement concrete poles/RCC poles/Steel poles complete of any size including PCC foundation and necessary excavation & earth work and making good to disturbed surfaces as directed by Engineer-in-Charge. 02/SR- 09, 12/SR-12

M & L PCC (1:3:6) type C-2 using 40 mm graded stone aggregate for foundation of stay assembly / struts / poles etc. 02/SR-3.90, 12/SR-5.00, 06/Rev-1.90

M & L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping including necessary form work complete all as directed by Engr-in-Charge. 02/SR-0.37, 12/SR-0.49, 06/Rev-0.16

Supply & install steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screw as specified Type 410 SP-31 (9 metres long) and providing with 02 coats of aluminium paint over a coat of red oxide primer complete all as directed by Engr-in-Charge. 02/SR-09, 12/SR-12, 06/Rev-04

S&F in replacement of conventional street light fitting any type/capacity with LED street light fitting 45W (IP-66) with integrated lens for asymmetrical light distribution, system lumen output of ≥ 6500 (± 2.5% )lumens, system efficacy ≥ 100 lm/W, LED lumen efficacy ≥ 120 lm/W, CCT 3000K~6500K, CRI >70, electronic driver, 10 kV in-built surge protection, Output open/short circuit protection, phase to phase protection, over-voltage protection, etc. as per IS-15885, THD<10%, PF ≥ 0.95, housed in pressure die cast aluminium housing including necessary fabrication for fixing of LED stree tlight all as per directed by Engineer-in-Charge. Make :- Syska, Havells,Philips, Bajaj, Wipro

Supply and fixing in replacement of New Generation Energy Saving LED flood light 150 watt. powder coated PDC aluminium body with toughened glass visior Efficacy >100Lm/w. Make;- Bajaj, Syska, philips,wipro

S&F polycarbonated unbreakable Junction box with fuse provn and suitable connection for three phase incoming cable, single phase out going cable endorsed in thermo plastic enclosure. Shock proof safe IP 65, weather proof, rust proof, dust and water proof internally embedded gasket with provn for cable entry through glade of size 200x160x98mm along with MS Clamps copper bus bar for three phase connection and 02X MCB SP 6 Amp 10 KA incl single phase 2.5 sqmm copper conductor PVC sheathed as required at site for electric connection to LED lights and connecting wire from JB to LED fitting as required complete all as specified directed.

Supply & fixing or laying galvanised steel tubing light grade 80 mm dia (ISI marked) for protection of under ground cable on poles / walls under road crossing etc of following sizes including dismantling & taking down existing pipe.

S&F GI tubing light grade with fittings to wall or pole as required of bore 50 mmdia including bends as in cooping etc. complete. 02/SR-09, 12/SR-36, 06/Rev-12

Taking out existing LT cable of any size and type, not more than 20 Mtr length from the loop trench and relaying the same after dressing of cable including replacment of aluminium lugs, nuts etc complete including necessary excavation & earth work complete all as specified and directed by Engineer-in-Charge.

Supply and fixing cable jointing kit termenation for 1.1 KV grade cable for straight through joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable and testing after jointing of size:-

16 - 35 Sqmm 3½ Core

50 - 95Sqmm 3½ Core

M&L for boring of existing road/path for laying of GI pipe protection for UG cable including making good distrurbed area/surface all as specified and directed. 02/SR-12, 12/SR-24, 06/Rev-12

M&L earthing complete as per electrical plate No. 3 of MES SSR Part-I with copper plate electrode 60cmx60cmx6.0mm thick, buried directly vertically in ground in a pit depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less then 1.5 metre below normal ground level connected to and including copper strip 20mm x 3mm by means of bolts, nuts check nuts and washers of galvanised iron or steel. Earthing strip shall be protected by galvanised iron or steel pipe 40mm bore light grade and connected to continuous earth wire on pole / test point. Watering pipe shall be 20 mm bore GI medium grade. The earthing shall be of inclusive of excavation & earth work in any type of soil, charcoal, salt, funnel PCC pit and RCC cover complete all as specified & tested complete.

M&L earthing complete as per electrical plate No. 3 of MES SSR Part-I with galvanised steel earth plate electrode 60cmx60cmx6.0mm thick, buried directly vertically in ground in a pit depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less then 1.5 metre below normal ground level connected to and including galvanised iron or steel earth strip 25mm x 4mm by means of bolts, nuts check nuts and washers of galvanised iron or steel. Earthing strip shall be protected by galvanised iron or steel pipe 40mm bore light grade and connected to continuous earth wire on pole / test point. Watering pipe shall be 20 mm bore GI medium grade. The earthing shall be of inclusive of excavation & earth work in any type of soil, charcoal, salt, funnel PCC pit and RCC cover complete all as specified & tested complete. 02/SR-10, 12 SR-11

06/REV/61SUB/Q3/20-21 Supply and fixing of 60 W LED street light with lens optics on LEDs, IP66 protected luminaire fixture made from pressure dia cast aluminum housing & heat resistance toughned glass cover with one number of 45 W driver, operating voltage range 130-275 Volt, suitable upto 50 mm mounting pipe as directed by engineer-in-charge. Make: Bajaj, Syska, Philips/Wipro/HPL Crompton Greaves

GI pipe bracket 40mm bore single swan neck shape suitable to fix on top of tubular pole complete with nuts, bolts and washers. 06/REV-04, 12/SR-12

S&F thermoplastic, polystyrene unbreakable junction box size 260 x 210 x 116 mm suitable for pole mounted outdoor type IP 65 insulated complete with FI clamp & nut, bolts, washers and including phase seperator between R, Y, B terminals and one MCB SP 6 amp 10 KA, all duly mounted on din cannel, cable glands for cable entry. Make : Hensel ,Cat Part No K9350,Sintex. 06/REV-04, 12/SR-12

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings base frame of 40x40x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming (a) MCCB 100 amps, 4 pole,(Ics==100% of Icu) 18 KA with adjustable thermal release, 50 Hz, 415 volts grade - 01 No. L&T Cat No CM90518OOKO (b) Bus bar electrolytic grade copper 200Amp, 4 pole, SMC insulators not less than 50cm long - 01 set. Outgoing (a) MCB TPN 63 Amp - 02 Nos L&T (b) Time Switch complete Assymbly astro rex D 21- 01 No and 3 phase contactor with on off control MCB TPN 63 amp and other connected accessories complete all as specied and directed by Engineer-in-Charge. Make:- L&T , Legrand, Sechneider Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (i) Panels shall be placed above 0.6 mtr from ground level (ii) Outgoing Cables shall be fed with solid busbar connectors. (iii) Cables shall be terminated using gun metal /SS glands.

12/SR/61SUB/Q3/2020-21 Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised and IP 54 suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming (a) MCCB 200 amps, 4 pole, 35/36 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make: L&T, Legrand, Scheineiders (b) Bus bar electrolytic grade copper 400Amp, 4 pole, SMC insulators not less than 75 cm long mounted on insulators -01 No. Outgoing (a) MCCB 160 amps, 4 pole, 25 KA with adjustable thermal over load release . 50 Hz, 415 volts grade -2 Nos. Make:L&T, Legrand, Scheineiders,C&S (b) MCCB 100 amps, 4 pole, 25 KA with adjustable thermal over load release . 50 Hz, 415 volts grade - 2 Nos. Make:L&T, Legrand, Scheineiders,C&S Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level (iii) Outgoing Cables shall be fed with solid busbar connectors. (iii) Cables shall be terminated using gun metal /SS glands.

All as per item No -32 above but with following accessoies comlete. Incoming (a) MCCB 160 amps, 4 pole, 35/36 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. MMake:L&T, Legrand, Scheineiders,C&S (b) Bus bar electrolytic grade copper 400 Amp, 4 pole SMC insulators , not less than 75 cm long mounted on insulators 01 No. Outgoing (a) MCCB 125 amps, 4 pole, 25 KA with adjustable thermal over load release. 50 Hz, 415 volts grade - 02 Nos. MMake:L&T, Legrand, Scheineiders,C&S (b) MCCB 100 amps, 4 pole, 25 KA with adjustable thermal over load release. 50 Hz, 415 volts grade - 02 Nos. Make:L&T, Legrand, Scheineiders,C&S (c) MCCB 63 amps, 4 pole, 25 KA with adjustable thermal over load release. 50 Hz, 415 volts grade - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S (d) Digital timer complete assembly, including connected switch gear, controls and wiring etc. in one compartment -01 set Note- All as above items No -06 here and there but with following earth workand pcc , accessoies comlete.

All as per item No -32 above but with following accessoies comlete. Incoming (a) MCCB 125 amps, 4 pole, 35/36 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S (b) Bus bar electrolytic grade copper 250 Amp, 4 pole SMC insulators , not less than 75 cm long mounted on insulators 01 No. Outgoing (a) MCCB 100 amps, 4 pole, 25 KA with adjustable thermal over load release. 50 Hz, 415 volts grade - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S (b) MCCB 63 amps, 4 pole, 25 KA with adjustable thermal over load release. 50 Hz, 415 volts grade - 02 Nos. Make:L&T, Legrand, Scheineiders,C&S (c) Time Switch complete Assymbly astro rex D 21- 01 No and 3 phase contactor with on off control MCB TPN 63 amp and other connected accessories complete all as specied and directed by Engineer-in-Charge. Make:- L&T , Legrand, Sechneider,C&S

All as per item No -32 above but with following accessoies comlete Incoming (a) MCCB 100 amps, 4 pole, 25 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S (b) Bus bar electrolytic grade copper 200 Amp, TPN SMC insulators - 01 No. Outgoing (a) MCCB63 amps, 4 pole, 25 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S (b) MCB TPN 63 amps, 4 pole, 10 KA - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S

All as per item No -32 above but with following accessoies comlete Incoming (a) MCCB 100 amps, 4 pole, 25 KA with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make:L&T, Legrand, Scheineiders,C&S Outgoing (a) Bus bar electrolytic grade copper 200 Amp, TPN SMC insulators - 01 No.

M & L for Supplying, fixing , connecting and testing in ON Load Change over switch 100 amp 4 pole ,with sheet steel enclouser including taking down complete all as directed by Engr-in-Charge.

S&F in replacement of conventional street light fitting any type/capacity with LED street light fitting 60W (IP-66) with integrated lens for asymmetrical light distribution, system lumen output of ≥ 6500 (± 2.5% )lumens, system efficacy ≥ 100 lm/W, LED lumen efficacy ≥ 120 lm/W, CCT 3000K~6500K, CRI >70, electronic driver, 10 kV in-built surge protection, Output open/short circuit protection, phase to phase protection, over-voltage protection, etc. as per IS-15885, THD<10%, PF ≥ 0.95, housed in pressure die cast aluminium housing including necessary fabrication for fixing of LED stree tlight all as per directed by Engineer-in-Charge. Make :- Syska, Havells,Philips, Bajaj, Wipro,C&S

M/S TRADE LINKERS

Pioneer Enterprises

M/S JAGDAMBA ENTERPRISES

LAKSHMI ASSOCIATES

M/S Anil Enterprises