SPECIAL REPAIRS TO BUILDING NO P-505 TO 512 (OR MD ACCN) ABDUL HAMID ENCLAVE AT OLD AMRITSAR CANTT

Amount

Taking down cement plaster on brick or stone or concrete surfaces of wall etc ,including raking out joints , hacking for key, scrubbing down with water complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for rendering 15 mm thick on fair face of brick works or concrete surfaces of walls with CM (1:6) , surfaces finished even and smooth without using extra cement complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for rendering 15mm thick on other than fair face of brick works or concrete surfaces of walls with CM (1:4) , surfaces finished even and smooth without using extra cement complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for rendering 5mm thick on the fair face of ceiling surfaces s with cement mortar (1:3), surfaces finished even and smooth without using extra cement complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of newly plastered or unplastered surfaces of walls and applying two coat of cement base paint over a coat of primer etc. complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer etc. complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of old decorated , plastered or unplastered surfaces of walls by Complete removal of existing treatment , including stipping nails, holes, filling the cracks with putty applying two coats of oil bound distemper complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of newly plastered or unplastered surfaces of ceiling and applying Three coats of white washing to ceiling , chajjas complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white washing to ceiling , chajjas complete all as specified and directed by the Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Brickwork (Except bricks) (using serviceable bricks obtained from dismantling) straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed by the Engineer-in-Charge.

Demolition of Reinfoced cement concrete for roofs, floors,(other than ground floors) beams , stair cases, landing,chajjaa and similar suspended work complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for reinforced cement concrete type B1 (1:2:4) (using 20mm graded crushed stone aggregate ) in Slabs supported on walls , beams and columns in floors , roofs ., landings, balconies , canopies, deck slabs and cover slab in shelves and the like complete all as specified and directed by the Engineer-in-Charge.

Formwork to the soffits of suspended slabs such as roof slabs , floor slabs , landings and similar work ; not exceeding 200 mm thick ( Horizontal or sloping ) and making flat rough finished surfaces of concrete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for TMT bars 6 to 8 mm mm dia and over , cut to length , bent to shape required , including cranking , bending spirally for hooping ends and binding with and including mild steel wire ( annealed ) not less than 0.9 mm dia or securing with clips complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs 15 mm Bib taps, cast copper alloy fancy type chromium plated with capstan head screwed down screwed for iron pipe of 15mm bore and fixed in repair complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs 15mm dia Stop valves, , high pressure, with crutch or butterfly handle, chromium plated, fancy type, screwed both ends for iron pipe or for unions complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs 15mm bore stop valve fancy type chromium plated with long shank and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs 20 mm gun metal globe or gate valve with iron wheel head, screwed both end for iron pipe complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with plated bracket guard and railing 60cm long complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs for Vitreous China wash basin, white, flat back, size 500 X 400mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs for brass chromium plated shower rose 125 mm size with swivel joint including fixing to 15mm dia steel pipe or union complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete as in repair complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe)including connection to trap, and to flushing pipe, anti-syphonage pipe etccomplete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demilition of PCC / Lime concrete bedding existing pan complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in rapairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs PVC waste pipe 32/38/40 mm dia, 600 to 750 mm long complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs stainless steel plate rack of size 1m x 1m, with folded edge gloss finish fixed to wall complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs 40mm waste fittings, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable rubbish off the premises complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with cement @ 3.0 Kg/Sqm complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes, surfaces finished even & fair complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 10mm thick Screed bed or beading layer of cement mortar (1:4) for vertical surfaces like dado, skirting etc. surfaces finished even & fair complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Non-skid Ceramic colour tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Non-skid Ceramic colour tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Glazed ceramic colour tiles in vertical surface like Dado/skirting as similar works of size 450mmx300mmx7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 20mm thick Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick Screed in cement mortar (1:6) complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for kota stone slab 20-25mm thick in flooring laid over 20 mm thick cement screed in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including poilshing complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for kota stone slab 15-20 mm thick in skirting laid over & including 10 mm thick screed bed in cement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including poilshing complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Sand filling under floors or in foundations including watering and well consolidation complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 80mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-40 Grade complete all as specified and directed by the Engineer-in-Charge.

Taking up or down steel tubing and connections for 15mm bore of pipe , including cleaning for refixing or removal to storecomplete all as specified and directed by the Engineer-in-Charge.

Re-fixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) including cleaning, re-running the old screw threads etc complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 15mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) complete all as specified and directed by the Engineer-in-Charge.

Taking up or down steel tubing and connections for 20mm bore of pipe , including cleaning for refixing or removal to storecomplete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 20 mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) complete all as specified and directed by the Engineer-in-Charge.

Re-fixing for 20mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) including cleaning, re-running the old screw threads etc complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 500 Litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with manhole cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 20 mm Ball valves high pressure of PTMT with epoxy coat ed Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0mm-210gms) complete all as specified and directed by the Engineer-in-Charge.

Taking down chowkats with shutters (without taking down of shutter from the frames) exc 1.50 Sqm and n.exc 4.00 Sqm each complete all as specified and directed by the Engineer-in-Charge.

Taking down chowkats with shutters (without taking down of shutter from the frames)n. exc 1.50 Sqm each complete all as specified and directed by the Engineer-in-Charge.

Taking down shutter of any description exc 1.00 Sqm and n.exc 2 Sqm each complete all as specified and directed by the Engineer-in-Charge.

Taking down shutter of any description n exc 1sqm each complete all as specified and directed by the Engineer-in-Charge.

Refixing Shutter of any description exc 1 sqm but n exc 2 sqm each complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for solid PVC door frames of size 50mm x 47mm made out of 5mm plain cover fillet colour PVC sheet reinforced with MS square tube for toilet complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either toside and as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in M.S frame welded/sealed to stiles and rails with suitable PVC sheet beading and jointed together with solvent cement. Supplying and fixing in the frame at site as specified of drawing complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165 complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 35mm thick factory made 2nd class hard wood plain framed pannelled shutter (any number of panel) with lock rail and panel of 12mm veneered board particle board of exterior grade with commercial veneering on both faces. The size of rail and style as per IS-1003 complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 25 mm thick flush shutter, soild core construction, with block board core and plywood face panel commercial type on both sides complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 35 mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass/gangue (with sash bars) edges of forming plain chamfered or rounded fitted with cut and mitred bead for securing glass/ gauged etc size of member of shutter as per Pt-I, Section 8, Clause 8.20 (a) complete all as specified and directed by the Engineer-in-Charge.

Taking down steel window / ventilator of any description & size n exc 1.50 sqm areacomplete all as specified and directed by the Engineer-in-Charge. complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for box type steel window, ERW hollow P-Section size 60 mm x 25 mm, double rebated ERW section of 1.25mm thick, comprising of glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one or two No openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast and guard bars etc as given below all as shown on drg No CEJZ/TD-06/07 incuding cutting holes and PCC 1:2:4, type B-1 in hold fast block, complete all as specified and directed as follows:- (a) Hold fast 150mm long of MS flat 12mm x 3mm - 4 Nos per Window (b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf (c) MS tower bolt 150mm long - 02 Nos per leaf (d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf (e) Cleat 55mm long of hollow square 15mm, 0.63mm thick- 01 Nos per leaf (f) MS pintol hinges size 75mmx12mm - 2 Nos per leaf (g) MS guard bar 10mm square bars @ 10cm c/c fixed horizontly Note:- Sheet glass, wire mesh and painting shall be measured and paid sperately. complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as stopper, cleat, pintal hinges, hold fast etc all as shown on drg No CEJZ/TD-06/07 dt 07.06.07 incuding cutting holes complete all as specified and directed by the Engineer-in-Charge. Note: Sheet glass and painting shall be measured and paid Separately.

Supply & Fixing for framed work such as framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; and similar workconforming to FE 290, Grade E-165 complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples in window and door as in new door/window. complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples / wooden beads in wooden / steel window and door as in repair complete all as specified and directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden & steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads exc 1.5 Sqm complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 3mm thick sheet glass in repairs , ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane including hacking out old broken glass ( any thickness, size , quality or description ) from wooden frames glazed with putty or fixed with beads . complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 4mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane in any position complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for butt hinges 100mm size medium weight cold rolled mild steel, fixed with screws or welded to steel frame complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 150 mm aluminum , anodised, barrel tower bolts of extruded section complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 200 mm aluminum , anodised, barrel tower bolts of extruded section complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 150 mm aluminum Handle Cast type complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 250mm aluminum alloy, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 2nd class hardwood small fittins such as brackets of any type, latch and hinge blocks, shapes door and window stops and the like including all necessary labours ; articles n exc 200 Cum each complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for Mild steel 300mm ordinary rat tail rod pattern spring including roller and roller plate complete including necessary welding to door frame complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of new wooden surfaces over 10cm girth or width and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of new steel surfaces and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described and apply One coat of synthetic enamel paint complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for flat iron as in hold fast,including tarring or coal tar black paint conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for PCC (1:2:4 ) type B1( using 20 mm graded aggregate ) Used as in Brick or concrete wall for fixing of holdfast including weathering, slightly rounded or chamfered angles and throating,complete all as specified and directed by the Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings (unreinforced) n.exc 15 cm thickness (below or above ground level) complete all as specified and directed by the Engineer-in-Charge.

Material and labour 50mm thick plain cement concrete 1 : 3 : 6 type C1 (using 20 mm graded stone aggregate) as in paving/ plinth protection laid in pannels including necessary form work, finished even and smooth without using extra cement, & filling the joint with bitumenous filler (bitumen mixed with sand) complete all as specified and as directed by Engr-in-Charge .

Supply and fixing for 25mm dia MS pipe PVC sheathed, decorative fancy type, curtain rod including brackets & a set of ABS finials complete all as specified and directed by the Engineer-in-Charge.

Dismantling of 100/75 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of floor/trenches, if required complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 110 mm bore PVC (SWR ) pipes single socketed, in any lenth with rubber ring & solvent fixed to wall complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 75 mm bore PVC (SWR ) pipes single socketed, in any lenth with rubber ring & solvent fixed to wall complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for PVC (SWR) bend 110 mm size complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for PVC (SWR) bend 75 mm size complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 110 mm bore PVC (SWR) single Tee complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for framed work as in cup board shutter, frame made of angle iron 35x35x6mm, covered with 1.00mm thick MS sheet, welded to frame including suitable handle, lugs and locking arrangement in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165 complete all as specified and directed by the Engineer-in-Charge.

Supplying and fixing PVC sheet 5mm thick, in backside of kitchen cabinets for support complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing for PVC board 18mm thick, in cupboard shelves and backside (for hanging) kitchen cabinet etc complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for solid PVC shutter 18mm thick with one side prelam of any shade plain colour as in cup board, kitchen cabinet shutter etc.complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 40mm long box type steel hinges spring action type complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 75-80mm long stainless steel handle complete complete all as specified and directed by the Engineer-in-Charge.

Dismantling brick tiles or terracing tile, single/double layer on roof including mud phuska any thickness and leepng plaster, seggregating, cleaning and stacking servicable tiles for reuse complete complete all as specified and directed by the Engineer-in-Charge.

Demoliton of mud in roof any thickness including mud plastering and removing to distance exc 250m but n exc 500m complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 40mm thick brick tiles, laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for brick tiles (except tiles) (using serviceable brick tiles obtained from dismantling) , laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for PCC (1:3:6) type C-0 (using 12.5mm graded stone aggregate) averaging 50 mm thick as in roof padding mixed with & including water proofing compund @ 100ml (minimum) per 50 Kg of cement finishing the surface even and smooth without using extra cement complete all as specified and directed .complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for 15mm thick plaster in CM (1:3) on RCC roof surfaces as in vertical surfaces mixed with & including water proofing compund @ 100ml (minimum) per 50 Kg of cement finishing the surface even and smooth without using extra cement complete all as specified and directed .complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces complete all as specified and directed by the Engineer-in-Charge.

Demolition of cement Concrete in sunken floors exc 15cm thick ( above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in sides of sunken slab benching etc including necessary form work complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Rendering 15mm thick cement plaster as in sunken portion in cement mortar 1:3 using & including water proofing compund @ 100ml (minimum) per 50 Kg of cement finishing the surface even and smooth without using extra cement complete all as specified and directed .complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 40mm bore steel water tubing grade galvanised inserted at the end of lateral slope projecting atleast 25cm beyond the outermost part of the building below the drain pipe up to two storey construction as spout for sunken, and all joints should be sealed properly by epoxy sealent complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Water proofing treatment to sunken floor including wall comprising with the following course of treatment/ specification from bottom to top. (a) Applying bituminous primer @ 0.40 ltrs per sqm over plastered surface of floor for treating the sunken floor all as specified & as directed by Engr-in-Charge. (b) Apply a coat of hot bitumen 85/25 penetration grade bitumen @ 1.20 kgs/Sqm. (c) One layer of 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application over entire area, complete complete all as specified and directed by the Engineer-in-Charge. Note:-(i) After plastering testing tobe carried out by ponding (For 48 Hrs) and any leakage/Seepage observed shall be rectified before water proofing treatment. (ii) Laying of APP membrane shall be done as per manufracturers instructions . (iii) Joints tobe touched hot and Minimum width of overlaps not less than 150mm.complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Plain cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate as in sunken filling as mass concrete or in sub base of floors complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Removing of nails, making good holes, cracks, etc and applying 2mm thick wall care puty on walls including finished the surface even and smooth complete complete all as specified and directed by the Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for foundation, manholes,sewage line etc exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed by the Engineer-in-Charge.

Returning,filling in,spreading,levelling,watering and well ramming in layers not exc 25cm thick each complete complete all as specified and directed by the Engineer-in-Charge.

Removing excavated material to a distance exc 250mtr but n.exc 500 mtr and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and directed by the Engineer-in-Charge.

Demolition and breaking up existing unserviceable 150 mm bore SGSW pipe and haunching against the sides of pipe at any depth including removing rubbish to a distance exceeding 100m complete all as specified and directed by the Engineer-in-Charge.

Supplying,laying in trenches, jointing and testing 150 mm bore salt glazed stoneware pipe grade 'A' drain pipe ISI marked all as specified & directed.( Excavation and earthwork shall be measured and paid for separately under appropriate items of Sch. 'A'.) complete all as specified and directed by the Engineer-in-Charge.

Material and labour for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) for bed of sewage lines of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for Point wiring for one light point/Bell/Fan point controlled by one switch complete with 1.5 Sq mm (nominal area)FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 25 mm dia and 1.5 mm wall thickness and conduit fittings including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire to common earth and connecting to earth dolly and Metal Flush box, cover plate with frame of suitable size for fixing modular switches/sockets/fan regulator etc complete all as specified for the following (Note : Cost of Metal boxes and modular accessories like cover plates will be included in quoated rate) complete all as specified and directed by the Engineer-in-Charge. (a) Fan point/ exhaust fan point / one light point / bell/ buzzer controlled by one switch/ bell push.

All as Ser item 125 here in before but One socket outet point 5 amps on the same board complete all as specified and directed by the Engineer-in-Charge.

All as Ser item 125 here in before but One socket outet point 5 amps on the independent board complete all as specified and directed by the Engineer-in-Charge.

All as Ser item 125 here in before but with 2.5 sq mm wire and earth wire of 1.5 sq mm for 3 Pin 15 Amp modular type socket outlet complete all as specified and directed by the Engineer-in-Charge. Note : Point wiring for power point will not be mixed with light/fan point circuit or not in the same conduit pipe complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing switch piano one way 5 A, SP, 230 Volts complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing Socket outlet 2 in 1, 3 pin 5 Amps Flush type complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing Switch outlet 2 in 1, 3 pin 15 Amps Flush type complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC complete complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing stepped type electronic fan regulator flush type complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for bell push, flush type, single pole 5 amps complete complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing of single phase call bell ‘DING DONG’, AC 230 volts single pole fixed over and including pressed steel sunk box of size 175 X 100 mm duly covered with 3 mm thick bakelite sheet complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for lamp holder insulated body angular type with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size and making good surface as original by plastering and whitewash/colour/distemper etc complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size and making good surface as original by plastering and whitewash/colour/distemper etc complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs MCB single pole, 240 volts, 40 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs MCB double pole, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed by the Engineer-in-Charge. (Note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate)complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for Blanking plate of plastic (suitable for distribution board) complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repair wall /ceiling mounting LED 18 Watt high quality sleek aluminum extruted tube light fitting complete with all acessories 1x18 Watt LED ,suitable for domestic application, 240 Volts, 50 Hz, including one tube rod and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete Make Havell's/Jaguar or its equivalent approved make in Phillps/Bajaj complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for 40 mm bore light grade galvanised iron tubing with all necessary GI fittings as in protection pipe of cable, fixed to pole or laid under floor / ground / under road crossings for protection of cable complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for Sand cushioning to UG cable 40cm wide 15cm and 10cm thick above and below the cable in trenches/ducts complete all as specified and directed by Engineer-in-Charge.

Supply and laying burnt brick sub class 'B' modular size, for cable protection laid length wise perpendicular to the axis of cable complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 25 sqmm 4 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.

Material & Labour for earthing complete with galvanised steel earth plate electrode 600mmx600mmx6.3 mm thick burried in ground vertically to a depth not less than 2.25 meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15 cm thick layers of common salt and charcoal dust starting FRLSom ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanised iron earth lead of size 4 mm by means of galvnised nuts, bolts and washers. GI wire of 4 mm dia laid in 15 mm dia light grade GI pipe as protection FRLSom top of the plate up to test point (cost of protection pipe up to 7.5 meters FRLSom earth electrode will be included in the rates quoted by the contractor) with following:- (a) test point of GI. (b) Watering pipe GI light grade 20mm dia FRLSom top of the earth electrode up to MS funnel with brass wire mesh embeded in floor of PCC earth pit. (GI watering pipe should properly tightned on GI plate & Funnel and embeded in PCC floor of earth pit) (c) PCC earth pit 30cmx30cmx30cm constructed in PCC 1:2:4 type B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 25mm thick with 1 Nos MS handles suitable for carrying of pit cover. (d) Angle Iron FRLSame Made of 40x40x4 mm size angle iron for holding earth pit cover. Note :- The cost of excavation, earth work, watering pipe, metal test point, MS funnel with brass wire mesh and RCC pit with pit cover have already been included in the rates. No extra cost shall be paid to the contractor against these items. complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs wall /ceiling mounting LED 9 Watt high quality sleek aluminum extruted tube light fitting complete with all acessories 1x9 Watt LED , suitable for domestic application, 240 Volts, 50 Hz, including one tube rod and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete complete all as specified and directed by the Engineer-in-Charge.

Taking down old unserviceable point wiring any type from existing conduit (light, fan, socket or power point etc) complete such as switches, ceiling rose, pendent, regulator and socket etc and removing the material FRLSom site and making good the disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, whitewash/colour/distemper etc complete all as complete complete all as specified and directed by the Engineer-in-Charge.

Material & Labour for for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with stranded copper conductor 6 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 4 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing in repairs energy saving new generation 10 watt LED, 6000k bulk head luminaire including 01 No 15 Watt LED Bulb with opal diffuser light fitting complete with all acessories and connection complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for decorative wall mounting light made up of polycarbonate suitable for 15 watt LED bulb B-22 including LED bulb 15 watt and connection complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for MCCB Incomer distribution board double door vertical type made out of CRCA MS sheet surface with insulated material like polyester or with epoxy powder coating surface mounting TPN 4 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and incl 100 amp 36 kA 4 pole MCCB with thermal - magnetic setting and Icu = Ics = 100% , including removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing in replacement of security light fitting LED 36 Watt aluminum pressure dia cast housing with touched glass cover IP-66 protection Including suitable size and accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal including taking down old CFL security light fitting complete complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for GI bracket light grade GI Pipe 1.2 mtr Length for fixing of street light fitting 36/40 Watt including connection complete all as specified and directed by the Engineer-in-Charge.

Supply & Fixing for Exhaust fan 300 mm sweep including cutting of walls , louvers nut and bolts etc including connection complete complete all as specified and directed by the Engineer-in-Charge.

amardeep traders

RAJ KAMAL BUILDERS

GEE EMM ASSOCIATES

m/s. gopal krishan

B.J.CONSTRUCTION CO