SPL REPAIR TO BLDG NO. P-80, P-81 AND P-83 OFFR MESS, OFFRS SINGLE LIVING ACCN AND CAR PARKING OF FD HOSPITAL UNDER GE (N) BATHINDA AT BATHINDA MIL STN

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each complete all as specified.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tubes of 19 gauge thickness & size 19 x 19 mm for stiles and 15 x 15 mm for top and bottom rails. MS frame shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC 'C' channel of size 30x 50mm forming styles and 5 mm thick 75 mm wide PVC sheets for top rail lock and bottom on either side and 10mm ( 5x 2mm) thick 20 mm wide cross PVC sheet as gap insert for top and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rail with 30mm wide x 5 mm thick PVC sheet beading on either side and jointed together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications and as directed by Engineer-in-Charge.

S & F 100 mm long aluminium anodised, barrel tower bolts extruded section complete.

S & F 100 mm long mild steel butt hinges , medium weight, cold rolled complete.

S & F 150 mm long aluminium handles , cast type, anodised complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each and removal to store including cutting holes for removal of hold fast complete.

S&F factory made pressed steel frames of size 125 mm x 60mm for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc (thickness of MS sheet shall not be less than 1.25 mm), including making good the wall with plaster in CM 1:6 compete, all as specified.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, compete, all as specified of frame size 105 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

M & L for PCC (1:3:6) type C-0 using 12.5 mm graded crushed stone aggregate as in filling back of pressed steel door frames/ chowkats and for fixing hold fasts etc complete all as specified.

S&F 35mm thick factory made panelled shutter (two panels) plain framed with lock rail and panel of 9mm thick B.W.P commercial ply conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood (Hollow) rails and styles and the size of rail and style as per IS-1003 (Part I) complete all as specified .

S&F factory made 35mm thick glazed/wire gauge and skeleton shutters three panel separated and prepared to receive glass, gauge etc (without sash bars), using second class hard wood (Hollow) the size of rails and style as per IS chemically pressure treated in factory against termite edges of grame chamfered or rounded fitting with cut and inserted beads complete all as specified. Note:- Wire gauge shall be measured and paid separately.

S & F mild steel wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with tinned tacked or galvanized steel wire staples complete.

S & F in repairs mild steel galvanized wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with galvanized steel wire staples complete.

S & F 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

S & F Aluminium anodized barrel tower bolts, extruded section length of bolt 200mm complete all as specified.

S & F aluminium 300mm long, anodised aluminium sliding door bolt with hasp, staple (bolt type), and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S & F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

S&F floor door stopper 150 mm size of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed.

S & F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of red oxide primer complete all as specified..

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including one shop coat of red oxide primer complete all as specified..

S & F factory made steel ventilator with top hung shutter incl hinges steel pegs & stays complete all as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips of size not exceeding 0.5 Sqm each pane complete all as specified.

Supply and fixing sheet glass, 3 mm thick ordinary quality fixed with oil putty to wooden or steel surface not exceeding 0.5 Sqm in each complete.

S & F figured glass pin head type sheet glass, 3 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete.

M&L for preparing new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint including preparation of surfaces complete all as specified.

M&L for preparing old steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint including preparation of surfaces complete all as specified.

M&L for preparing new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified.

M&L for preparing old wooden surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint including preparation of surfaces complete all as specified.

Digging out and removing sunken floor filling and depositing the same at a distance not exceeding 250 M away from the outer edge of bldg where as directed complete all as specified.

Supply only liquid water proofing compound, ISI marked.

M&L for sunken treatment to sunken floor, cleaning the surface by using wire brush, rendering to floor and sides with 10 mm thick cement mortar (1:4) including mixing of liquid water proofing material as per manufacturer's instruction, finished even and smooth without using extra cement after that material & labour for providing two coats of two components (one part liquid two parts powder) ready to use cementations water proofing coating on properly prepared surfaces by brushing having elongation of >50% for the applying water proofing treatment as per following on horizontal and vertical surfaces of sunken floor complete all as per manufacturers instruction. (i) Applying 1st coat of two components modified polymer coating. (ii) Provn of glass fiber mess of 2 x 2mm immediately on alone coating. (iii) Apply 2nd coat of two components modified polymer coating after 72 hrs on horizontal and vertical surfaces. NOTE :- (i) Complete treatment shall be carried out by authorized applicators of water proofing manufacturers . (ii) WP Materials shall be measured and paid for separately as supply only in this BOQ.

M & L for 30mm thick PCC (1:2:4) type B0 using 12.50 mm graded stone aggregate with using water proofing compound as per manufacturer's instruction as in sunken floor all as specified.. (Note :- WP Materials shall be measured and paid for separately as supply only in this BOQ.)

M & L for PCC (1:7:12) type F2 using 40 mm graded stone aggregate with using liquid water proofing compound @ 0.20 ltr per bag of cement as in filling & mass concrete in sub base , floor all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for non skid ceramic coloured tiles, 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) complete all as specified. Note: Only course sand shall be used in screed bed.

M & L for glazed ceramic coloured tiles 450 x 350mm, 7 to 8mm thick in vertical surfaces such as dado / skirting, set and jointed in neat cement slurry and pointed in white or coloured cement pigmented to the match the shade of tiles laid over and including M & L for 10 mm thick rendering in cement mortar (1:4) as backing coat and finishing the surface rough to receive the tile complete all as specified.

M & L for vitrified ceramic tiles, 10 mm thick (square / rectangular), dark shade, polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles over and including M & L for 15 mm thick Screed bed or bedding layer in CM (1:6) complete all as specified.

M & L for vitrified ceramic tiles, 10 mm thick (square / rectangular), dark shade, polished, area of each tiles not exceeding 0.36 Sqm, in vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles over and including M & L for 10 mm thick rendering in CM (1:4) complete all as specified.

M & L for machine cut kota stone slab as in flooring, 20-25 mm thick over and including M & L for 15 mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M & L for machine cut kota stone slab 20 to 25 mm thick as in riser of steps , skirting , dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including M & L for 10 mm thick rendering in CM (1:4) complete all as specified.

M&L for 18 to 20 mm thick granite work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including M & L for 10mm thick screed beding in CM 1:4 complete all as specified.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm complete.

M & L for prelaminated particle board, 18/19mm thick, medium density, flat pressed, three layer type with BWR type adhesive, exterior grade quality, prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised of 40 mm width of flap (when open) complete all as specified.

S & F mild steel drawer pulls, 3 screw plate with fixed dished pull 80mm to 100mm long complete.

Dismantling framed timber scantlings 40 sq cm and over in section in framed work in any position complete all as specified.

M & L for second class hard wood, clean sawn, in scantlings 40 sqcm and over in section, unframed work complete all as specified.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified

S&F in repairs 15 mm cock cast or angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified.

S & F in repairs brass chromium plated shower rose 125 mm size with swivel joints including fixing to steel pipe or union complete all as specified and as directed.

S & F in repairs 15 mm chromium plated concealed stop cock complete all as specified and as directed.

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long including end brackets complete all as specified.

S&F in repairs, chromium plated soap dish /tray of approx size 100 x 100 x 6mm and fixed to plugs on wall with chromium plated screws complete.

S&F in repairs bib taps, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore dia of pipe.

S&F in repairs curtain rod mild steel, chromium plated of 19/20 mm dia fixing with brackets, stops, rollers etc as per site requirement complete all as specified.

Taking up or down 15mm bore galvanized iron tubing and connections, including cleaning for refixing or removal from site complete all as specified.

Taking up or down 20mm bore galvanized iron tubing and connections, including cleaning for refixing or removal from site complete all as specified.

Taking up or down 25mm bore galvanized iron tubing and connections, including cleaning for refixing or removal from site complete all as specified.

S & F GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 15 mm complete all as specified

S & F GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 20 mm complete all as specified

S & F GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 25 mm complete all as specified

S & F in repairs vitreous china wash hand basin, white, of size 550mm x 400mm , counter sunk in granite slab complete including waste, chain and plug and porcelain stopper. 32 mm dia waste coupling all as directed complete .

Fixing in repairs vitreous china wash hand basin of any size, colour and type obtained from site including waste, chain and plug and porcelain stopper, including M & L for 32 mm dia waste coupling fancy type chromium plated, PVC waste pipe of 32 mm dia and mild steel angle iron brackets complete all as specified and directed . Note:- Old wash basin of any size, colour and type obtained from site shall be fixed in this item.

S&F in repairs vitreous china urinal, half stall type, white, including and providing and fixing plugs, bedding urinal against wall in CM (1:2) securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified.

Taking down 100 mm dia AC eaves gutters and rain water pipes (any size or pattern ), including all fittings, heads, shoes, bends, swan necks, etc, complete all as specified.

S&F HDPE pipe (ISI Marked) 110mm bore for rain water pipe conforming to IS : 1984 pressure rating at 2.5 kg /sq cm including necessary cutting of holes in parapet/ wall as required at site complete all as specified.

S & F 110 mm bore HDPE bends (ISI marked) of any radius to suit rain water pipes complete as directed.

S & F in repairs Gun metal globe or Gate valve with iron wheel head , screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm x 260 mm, white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor and excluding flushing cistern, flush pipe and waste pipe complete all as specified.

S&F in repairs vitreous china wash down water closet , (pedestal pattern) EWC , white with white coloured seat cover , 'P' or 'S' trap including connection to drain or outgoing pipe and to flushing pipe, etc. including making good to floor complete all as specified.

S & F in repairs PVC valve less, syphonic action type, flushing cistern, 10 liters capacity, low level, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe 32mm dia and PVC connection complete all as specified.

Dismantling and disconnecting of existing cast iron soil waste & vent pipe or reinforced concrete drain pipes of any dia / bore fixed to wall or laid in trenches incl all fittings, jointed in cement mortar and taking out of trenches, if required.

S & F 100 mm dia cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

All as per ser item 75 above but fixed to walls

S & F 75 mm dia cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

All as per ser item 77 above but fixed to walls

S & F in repairs 100mm dia cast iron bends (any radius), diminishing pieces or tapers (large bore measured) complete all as specified.

All as per ser item 79 above but with oval access door.

S & F in repairs 100mm cast iron Cowl fixed with cement joint in CM 1:2 complete all as specified.

S & F in repairs 100mm bore cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

S & F in repairs SGSW Gully trap of size 150 x 150 mm, set and jointed to drain in CM 1:1 complete all as specified.

S & F in repairs 75mm dia cast iron bends (any radius), diminishing pieces or tapers (large bore measured) complete all as specified.

All as per ser item 84 above but with oval access door complete all as specified.

S & F in repairs 75mm cast iron Cowl fixed with cement joint in CM 1:2 complete all as specified.

S & F in repairs 75mm bore cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

S & F in repairs 75mm dia cast iron floor trap with chromium plated grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.

S & F in repairs Stack clamps made out of 50 x 5 mm flat iron and 16 mm dia round iron stay including nuts , bolts and securing ends of stays to wall or roof complete for 100 mm bore dia pipe all as specified.

Dismantling of brick tiles or terracing tiles, single layer on roof including any type of water proofing membrane and disposal of retrieved unserviceable material upto a distance not exc 250 mtr away complete all as specified.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 250 mtr away from site and disposal off in low lying area complete.

M & L for cleaning of top surfaces of concrete roof slab , lime terracing , or surface of tiles with wire brush including flashing and junction of parapets etc and surface painting with layer of blown grade bitumen of any penetration applied hot @ 1.70 Kg / Sqm and rendering in 15 mm thick in cement mortar (1:4), priming the surface @ 0.30 Kg / Sqm and laying 3 mm thick APP based polymer membrane of weighing not less than 3 Kg / Sqm reinforced with polyster non woven fabric (Weight not less than 150 Gm / Sqm) laid on primed surfaces by torch application with side over lap 75mm and end over lap 100mm and tucked into the chases as a treatment for moderate condition complete all as specified and as directed.

M & L for providing lime concrete (1:3) using 40 mm graded stone aggregates as leveling course on roof slab complete all as specified and directed.

M&L for 40 mm thick brick tiles laid on cement mortar (1:6), 20 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement or mud phuska complete all as specified.

All as per ser item No. 94 here-in-above but except tiles

M & L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping , steps , bed block, complete.

Taking down cement of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M & L for rendering 15 mm thick in patches in cement mortar (1:6) on other than fair face of brick work or concrete surfaces of walls and finishing the surface even & smooth without using extra cement complete all as specified.

M & L for rendering 15 mm thick in cement mortar (1:4) mixing with WPC @ 3% by wt of cement on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified. (NOTE – WP material shall be measured and paid for separately as supply only in this BOQ.)

All as per ser item No. 99 here-in-before but on ceiling surfaces in 5 mm thick in CM 1:3.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete all as specified.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection complete all as specified.

Demolition of RCC of any description & in any position not otherwise specifically provided for, complete all as specified.

M & L for RCC (1:2:4) type B1 using 20mm graded stone aggregate as in Chajjas, lintel etc complete all as specified.

M & L for TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M & L for Use and Waste of form work to soffits and sides of chajjas and similar work for fair finished surface of concrete etc complete all as specified.

S & F 1000 litres capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and type from site complete all as directed.

S&F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 25 mm bore (minimum weight 25mm-455 gram) complete all as specified.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash etc complete all as specified.

M&L for preparing old plastered surfaces of ceiling and applying three coats of white wash etc including complete removal of existing treatment complete all as specified.

M&L for preparation of new plastered surfaces of walls/ pillars/ cornices by brooming down with using broom/ sand papering or by any other means, preparing the surfaces smooth by applying one coat of wall care putty( 3mm) and after that applying two coats of oil bound distemper ( washable) as per approved tint/ colour over a coat of suitable primer with using roller/ brush complete all as specified.

M & L for preparation of old plastered surfaces of internal walls and applying the following:- (i) Applying wall care putty in one coat( 3mm each) on wall surfaces & smoothening the surface with sand papers/ mechanized sanding etc (preparatory to paint as directed) complete all as specified. (ii) Two coats of oil bound distemper of approved tint over a coat of suitable primer by using airless spray / roller. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparation of newly plastered surfaces of external walls and applying two coats of cement base paint of approved tint by using roller/brush over and including a coat of cement base primer complete all as specified.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces with wall putty and M & L for preparation of old plastered surfaces of walls and applying the following:- (i) Two coats of cement base paint of approval tint by using airless spray/ roller over and including a coat of acylic external primer .

Supply only 15mm bore chromium plated, fancy type, quarter turn Pillar cock screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified.

Demolition and breaking up drain pipes (SGSW, AC or Reinforced concrete) of dia up and including 150 mm bore set in cement mortar, laid in trenches / fixed on walls including all fittings, accessories, encasing etc complete all as specified.

M & L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate bed to drain pipes including packing under and hunching against the sides of the pipes 150 mm dia after they are laid and tested in trenches complete all as specified .

M & L for 150mm internal dia SGSW pipes, grade 'A', laid in trenches and jointed complete all as specified.

S&F factory made powder coated aluminium frame for doors, windows, ventilators with section weighting 0.98 kg/ rm with one or more rebates including joining cleat for fixing etc. complete all as specified. (minimum thickness of powder coating shall be 50 micron)

S&F factory made powder coated (minimum thickness of powder coating shall be 50 micron) aluminium door shutters, aluminium section weighting 0.55 kg/ rm including necessary joining cleats, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc complete all as specified.

S & F sheet glass, 4mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified.

S&F Solar control film 25 micron reflective type ( gareware sun control or equivalent) complete all as specified.

S & F door closer hydraulically regulated, designation No 3, universal type, aluminium (extruded section) body, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specifed.

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc except concealed conduit and sunken boxes and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including M & L for rigid non metallic PVC concealed conduit not less than 20mm dia (medium duty ISI marked) and conduit fittings concealed in wall/ ceiling with and including modular metal flush box and modular cover plate with frame of suitable size and matching colour of required module for mounting or housing switches, socket outlets, fan regulators etc including blanking plates and all other fixing accessories for one fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and directed.

All as per item No 126 here in before but for one socket outlet 5 pin, 5/6 Amp 250 volts flush type on same board complete all as specified.

All as per item No 126 here in before but for one socket outlet 5 pin, 5/6 Amp 250 volts flush type on independent board complete all as specified.

All as per item No 126 here in before but for one socket outlet 6 pin, 6/16 Amp 2 in 1 with cable 2.5 sqmm multistranded copper conductor FRLSH cable on the independent board including provn of 2.5 Sqmm PVC insulated copper conductor FRLSH cable continues as earth wire connected to earth dolly complete all as specified.

All as per item No 126 here in before but one bell/ buzzer point controlled by one push botton switch with cable 1.5 sqmm complete all as specified.

All as per item No 126 here in before but two way point controlled by two 2-way switches complete all as specified.

S & F Switch modular , flush type, single pole, one way, 5/6 Amp .

S & F modular socket outlet universal, 3 Pin 6 Amp, flush type. (Note: Switch and socket shall be of same make.)

S & F for 16 Amps switch modular type with indicator , 230 volts, AC ISI marked complete all as specified.

S & F for socket universal 6/16 Amps modular type, 230 volts, AC ISI marked complete all as specified.

S & F for bell push 6 Amps one way modular type , 230 volts, AC, ISI marked complete all as specified.

S & F for 6 Amps switch modular type , 230 volts, AC two way ISI marked complete all as specified.

S&F electric / electronic bell, ding dong type, 230 Volt, AC supply complete all as specified.

S & F ceiling rose, 3 plate, surface bakelite type, Polycorbonate body, 6 Amps, 250 Volts AC, 65 x 50 mm, three terminal (ISI marked) complete all as specified.

S & F for fan regulator electronic step type (1-4), modular type , 230-240 volts, AC, complete all as specified.

S & F jumbo batten holder of PVC/Polycarbonate type with jumbo skirt suitable for batten fitting including of 9/10 watt LED bulb 6000K complete all as specified.

S & F wall mounted LED batten fitting 1 x 20 watt, 6000 K min 100 lumen per watt, 4 ft complete with decorative ultra slim square profile liner LED lighting fixture with extruded polycarbonate environment friendly , energy efficient complete with all light fittings connections all as specified and directed .

S & F recessed / suspended LED ceiling light with wide light window for maximized glare free output suitable for 600 x 600 mm and suspended fitting with separate electronic driver and high brightness LEDs 36 watt ( 100 lumens per watt) not less than 5700 K including connecting electric connection, complete all as specified.

S & F round shape 6 watt, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting to electric point by using flexible copper wire twin core upto ceiling rose/ connector complete all as directed.

M & L for LED mirror light fitting of 09/10 watt, 6000K, linear & compact with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete lamp and all other accessories fitting arrangement including connecting to electric point by using flexible copper wire twin core upto ceiling rose/ connector complete all as directed.

Hanging only lights of any description and type after repair of ceiling / roof work . Note:- Old existing / new lights providing by user of any type and size shall be used for hanging in this item.

Fixing only wall mounted decorative bracket light of any type and size. Note:- Old existing / new lights providing by user of any type and size shall be used for fixing in this item.

S&F in repairs new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP 66 roadway luminair with high power LED of 25/35 watt toughened glass complete with GI bracket (01 No) MS clamps (02Nos) suitable for security light fitting fixing to wall/column & electrical connection to the light fitting providing 1.5 mtr long twin core round copper conductor cable of suitable size and testing compete all as specified.

S & F in replacement of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 volt , 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current mortor (BLDC) and old rusted and outdated ceiling fans deposited to MES store complete all as specified and directed.

S & F in replacement of exhaust fan 450 mm sweep BEE , 5 star rated and electrical connection providing twin core round copper conductor cable of suitable size and old exhaust fan deposited to MES store complete all as specified

S & F in replacement of exhaust fan 300 mm sweep BEE , 5 star rated and electrical connection providing twin core round copper conductor cable of suitable size and old exhaust fan deposited to MES store complete all as specified

Taking down existing Geysers from site before the building tiles/ plastering and refix the same after completion of tiles/ plastering work including painting of Geysers and fixing arrangements and testing of required for proper functionality and including electric/ earth connections and carrying out grouting and complete installations with mounting bolts, nuts including testing after installation complete all as specified and directed.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc complete all as specified.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 12 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc complete all as specified.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 4 way, DB TPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc complete all as specified.

S & F MCB SPN 63 Amps, 10 KA 'C' Curve, 240 Volt, AC, 50 Hz including necessary attachment complete all as specified.

S & F MCB TPN 100 Amps, 10 KA 'C' Curve, 240 Volt, AC, 50 Hz including necessary attachment complete all as specified.

S & F MCB, SPN, 6 to 40 Amps, 10 KA 'C' Curve,240 volt including taking down old unserviceable MCB SPN complete all as specified.

S & F AC connection box / Geyser connection box, SPN type with two pin & earth plug and socket ( industrial type DB) with and including one MCB SPN 'C' Curve type capacity 32 Amps, 10 KA complete all as specified.

M&L for concealed sub main wiring with 2 single core cable 6 sqmm, 1100 volts grade PVC insulated unsheathed of copper multi standard conductor FRLSH cable with continuous copper earth conductor of size 6 sqmm, 1100 volts grade drawing through in & including M & L for non metallic PVC conduit of size 20 mm includig all fittings and accessories including cutting chases for conduits as required sinking of terminal boxes, making good the same including taking down old unserviceable sub main wiring complete all as specified. Note :- Two runs of cable and one run of earth wire shall be measured as one unit.

M&L for concealed sub main wiring with 2 single core cable 4 sqmm, 1100 volts grade PVC insulated unsheathed of copper multi standard conductor FRLSH cable with continuous copper earth conductor of size 4 sqmm, 1100 volts grade drawing through in & including M & L for non metallic PVC conduit of size 20 mm includig all fittings and accessories including cutting chases for conduits as required sinking of terminal boxes, making good the same including taking down old unserviceable sub main wiring complete all as specified. Note :- Two runs of cable and one run of earth wire shall be measured as one unit.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia medium grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion including taking out old existing earthing of any type and size.. Note :- (a) PCC chamber shall be constructed at least 1.5 m away from earth pit. Pipe for watering shall be provided in slanting manner. (b) 4mm dia GI wire and 15mm dia light grade GI protection pipe upto 7.5 metre shall deemed to be included in quoted rate.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ

V K CONTRACTOR

Ajay Enterprises

M/s MITTAL CONSTRUCTIONS

R K GOYAL & COMPANY

M/s Kamal Builders