SPECIAL REPAIR TO BUILDING NO P-47 AND P-80 UNDER GE (NORTH) MAMUN AT MAMUN MIL STN

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Taking down Shutters of any description not exc 1 sqm each including builders hardware complete all as specified and directed.

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 75mmx50mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface, complete all as specified and directed.

M&L for 18 to 20mm thick prelaminated PVC solid board (one side decorative choice laminate and other side balancing white) as in kitchen cabinet, cupboard and pelmet box fixed with screws to PVC/timber frame work complete all as specified and directed.

M & L for Solid PVC Door Frame of size 50mm x 95mm made out of 5mm wood grain colour prelam PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters (Factory made) of 2nd class hard wood and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 2009 (Larger size to be provided) incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for Factory made solid PVC moulded door shutters, 28 to 30mm thick (stiles), with PVC solid board core not less than 18mm thick and 2, 4, or 6 raised panel design with 5mm thick moulded wood grain coloured prelam PVC sheet on the front face & 5mm thick prelam wood grain coloured prelam PVC sheet on back face, supplied and fixed in frame at site as per specification and shown in SSR Part-II Section-8 complete all as specified and directed.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3 mm thick Figured glass, pin head type and glazing with oil putty in squares not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

S&F 100mm long stainless steel butt hinge medium weight cold rolled complete all as specified and directed.

M&L for Aluminium anodised barrel tower bolt, extruded section 200mm long , complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150 mm complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 100 mm complete all as specified and directed.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

M & L for Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours articles n exc 200 cu. cm each using 2nd class hard wood complete all as specified and directed.

S&F Hasp and staple aluminium anodized 100mm long including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for 300 mm aluminium alloy sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section complete all as specified and directed.

M&L for 25 mm thick floor in PCC 1:2:4 type B-0 finished even & fair as in subbase of floor,including dismantling existing floor of any type and pattern and removal of rubbish out off the premises complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio (1:2) by weight including dismantling existing floor of any type and pattern and removal of rubbish out off the premises complete all as specified and directed.

M&L for 60mm thick factory made rubberised coloured (laminated) interlocking paver block (using vibro compaction method) (topping thickness not less than 5mm) in white cement and non fadable glossy pigment of approved shade of any shape and size conforming to IS-15658-2006 of M-35 grade laid over & including cleaned dry sand cushion 50mm thick over and including 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) including demolition of damaged cement concrete of any type or description and removal of debris out off the premises etc complete all as specified and directed.

M&L for Cement concrete (1:1.5:3) type A-1 (using 20mm graded crushed stone aggregates) such as in column for fixing of truss, benching, coping, Bed blocks and the like, rounded or chamfered on edges including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) including roughening surfaces of existing concrete floor by picking, sweeping clean & washing down with water to remove dust and apply neat cement slurry @ 3.00kg of cement per sqm complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick as in skirting area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10mm thick screed bed or bedding layer of cement mortar (1:4) including taking out cement plaster sweeping clean & washing down with water to remove dust complete all as specified and directed.

M&L for Marble Green/Bhaislana Zebra 12 to 15mm thick (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like set and jointed in neat cement slurry including pointing in epoxy grout to match marble shade, including making hole for gas pipe including rounding the edges of marble stone , laid over and including 15mm thick screed bed in CM 1:4 including dismantling of existing tiles/stone etc complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F Peg set of six, powder coated fixed with chromium plated brass screws and wooden & plastic cleats (minimum weight 190 grams) complete all as specified and directed.

S&F 15 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 500 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

All as per Srl tem No 40 above but except pipes ( Refixing old retrived serviceable Pipes) ( Refixing old retrived serviceable Pipes) but with all new fittings complete all as specified and directed.

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

All as per Srl tem No 42 above but except pipes (Refixing old retrived serviceable Pipes) (Refixing old retrived serviceable Pipes) but with all new fittings complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exc 10 cm girth complete all as specified & directed.

S&F in repair for 25mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC brackets of approved design/pattern, funnels etc suitable for single curtain rod complete all as specified and approved by GE.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises, etc complete all as specified and directed

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan exceeding 6m mean radius built in CM (1:6), complete all as specified and directed.

All as per Srl item No 47 above but except bricks ( using retrieved bricks from dismantling) complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius in half brick thick walls, built in CM (1:4), complete all as specified and directed.

All as per Srl item No 49 above but except bricks (using retrieved bricks from dismantling) complete all as specified and directed.

M&L for rendering 5mm thick cement plaster on surfaces of concrete ceiling in cement mortar 1:3, surface finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and removal of rubbish out off the premises, complete all as specified & directed.

M&L for Rendering 15mm thick in two layers base layer 10mm thick in CM 1:6 & finishing layer 5mm thick in cement mortar (1:4) using liquid water proofing compound [ In 2nd layer only] on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises, etc complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:3) on in fasia /edges/ ceiling of chajjas/ roof projections etc surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

S&F in repair Soap Dispenser with glass bottle and chromium plated base frame fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Jaquar Cat part No ACN-1135N or equivalent of Hindware/Marc.

S&F in repair Glass shelf assembly 55cm long with brass chromium plated bracket guard and railing fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Jaquar Cat part No AQN-7771 or equivalent model in Hindware/Marc.

M&L for 20 mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe, fixed in repair, etc complete all as specified and directed.

S&F in repair for Vitreous china White Squatting Orissa Pattern pan (Make : Somany Cat part No 121115 or equivalent Cat Part/Modelof Hindware/Parryware) of size 580x440mm, including cast iron ‘P’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe etc complete all as specified and directed. (Note : Demolition and refilling of concrete PCC 1:5:10 type E-2 in sunken portion shall be measured & paid separately.)

S&F in repair PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore and PVC connection 15mm bore 450mm long complete all as specified and directed.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including 15mm bore fancy type Pillar taps, cast copper alloy, with long screwed shank and fly nuts, chromium plated (Make : Jainko Cat part No PCJ-1 or equivalent model in Hindware/Marc.) brackets, CP waste coupling, 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

S&F in repair for Stainless steel sink with draining board 1mm thick sheet for kitchen with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm, including 32mm bore PVC waste outlet pipe of minimum length 600mm complete all as specified and directed. Make : Blue star Cat part No. BSSBSD-52 or equivalent model in Nirali/Jyoti

S&F Stainless steel plate rack of approx size 750x900mm fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Blue star Cat part No. KPR-312 or equivalent model in Nirali /Jyoti

M&L for Filling of sunken floor with PCC 1:5:10 type D-2 using 40mm graded crushed stone aggregate including breaking and removal of existing filling of lime concrete/PCC/brick bats and rubbish out off the premises, etc complete all as specified and directed.

M&L for Rendering 15 mm thick on brick work or concrete surfaces in CM 1:4 with and including water proofing compound to sunken portion with proper slope towards outside and finishing cement concrete surface even and smooth using extra cement including application of 90 micron polythene film and applying bitumen coating @ 3.00 Kg/Sqm etc complete all as specified and directed. [Note : WPC shall be measured and paid seperately]

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for RCC( 1:1.5:3) type A-1 using 20mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork including demolition of existing cover slabs of any description and removal of rubbish out off the premises etc complete all as specified and directed.

M&L for Precast cement concrete (1:1.5:3) type A-1 using 20mm graded crushed stone aggregate in cover slabs of manhole, drains & similar articles set in cement mortar 1:4 incl formwork including demolition of existing cover slabs of any description and removal of rubbish out off the premises complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately)

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

M&L for Reinforced concrete pipes 200 mm bore ( Internal dia ), class NP2, laid and jointed complete with collars complete all as specified & directed. (Note : WPC shall be measured and paid separately)

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, laid in floor complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 25mm x 3mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, laid in floor complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 25mm x 3mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 50 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 25mm x 3mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron branch pieces or Tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors etc complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron branch pieces or Tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors etc complete all as specified and directed.

S&F in repair for 75 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair 100 mm Cast iron Swan necks (or off- sets) upto 152 mm projection , fixed with cement joints complete all as specified and directed.

S&F in repair 50 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains for 150 mm bore & making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-2(using 40mm graded crushed stone aggregates) as in surface channels and drains including demolition of existing cover slabs of any description and removal of rubbish out off the premises etc complete all as specified and directed. complete all as specified and directed.

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in roof padding finishing top surface even and smooth using extra cement complete all as specified and directed

Dismentling and M&L for providing bedding layer of mortar 20mm thick in cement mortar 1:4 with WPC over and including neat cement slurry @ 3 kg of cement per Sqm on existing roof surfaces including finishing top surface even and smooth using extra cement complete all as specified and directed (Note : WPC shall measured and paid separately)

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/ Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

M&L for PCC 1:3:6 type C-2 as in Concrete bed to drain pipes 150 mm bore ( Internal dia ) including after they are laid and tested complete all as specified and directed.

M&L for precast manhole cover in RCC (1:1.5:3) type A1 with angle iron frame of size 40 x 40x5 mm fixed in repairs complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over a layer of wall care putty 2 mm thick complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer as per manufacturer instructions complete all as specified and directed.

M&L for Preparation of existing distempered surfaces of walls by complete removal of existing treatment and apply two coats of distemper oil emulsion (OBD) over a coat of cement wall primer (from same manufacturer of OBD) over a layer of wall care putty not less than 3mm thick etc complete all as specified and directed.

Preparing new /Old wall surface including making surface clean, dry and free from any loose paint film, dirt, chalk, grease, fungus and algae and applying two coats of acrylic , antifungal emulsion exterior weather proof paint on external surfaces, complete all as specified & directed.

M&L preparation of old treated steel surfaces of any description over 10 cm in width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of existing white washed surfaces of walls and apply two coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of existing white washed surfaces of ceiling and apply two coats of white wash on plastered surfaces complete all as specified and directed.

M&L for Preparation of existing painted surfaces of walls & complete removal of existing treatment and apply two coats of cement base paint over a coat of alkali primer (from same manufacturer ) over complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 106 above but one light point controlled by two Nos switch 06 Amp two way, complete all as specified and directed.

All as per Srl item No. 106 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 106 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 106 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S&F Modular Socket outlet, 5 pin, multi purpose, 2 module 6/16 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 or equivalent of Legrand/Siemens/Schenider/Anchor Roma

S&F Modular Switch 2 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S&F Modular bell push, 10 Amp, AC 230 Volt etc complete all as specified and directed. Make : Legrand Cat Part No 673404/ Anchor Roma Cat Par No 289101/ Schenider Cat Part No P1005.

S & F modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

S & F modular switch piano type flush button one way 06/10 Amp one module complete all as specified and directed. Make : Legrand Cat Part No 673000/Crabtree Cat Part No ACMSXXW101/Anchor Roma Cat Part No 66111.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 50x20mm, three terminals, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 39040 or equivalent of Havells(Reo)/SSK (Topline)/GM (Vyoma)

M &L for ceiling fan 1200 mm sweep star rated with down rod & all accesseroies with & incl modular type fan regulator socket type 120 watt fixed in repairs complete all as specified and directed.

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S&F for Bell Ding Dong AC 230 Volt, single Pole complete all as specified and directed. Make : Anchor Cat Part No 8024/Cona Cat Part No 2856/ Anchor Cat Part No 8272/GM Cat Part No 4001.

S&F Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S &F the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S&F Mirror decorative light of toughened glass and having with and including 1X7 Watt LED mounting on surface with high output diffuser and 1' length with all accessories connected with and including twisted flexible copper conductor all as specified and direted.

S &F building LED security light luminaries 35 W LED 5000K AC 230 volts, new generation saving & enviromental friendly long life versatile pressure die cast aluminium luminaries with high power LED as light source complete making connection with street light/ building security light box or OH line using PVC insulated and sheathed single core multi stranded copper conductor cable of size 1.5Sqmm including suitable size 32mm of bracket and light grade pipe for muntaining of fitting complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 12W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.Notes : Notes for Srl item No 121 to 125:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation.

S&F Double door MCB DB TPN, 415 Volts, 04 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar, including taking out old unserviciable DB any size/type complete all as specified and directed.

S&F Double door MCB DB SPN, 240 Volts, 08 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar including taking out old unsv DB any size/type, complete all as specified and directed. Make: Legrand Cat Part No 6077-11 or equivalent model in L&T/Hager/SCHNEIDER

S&F for MCCB tripple pole & neutral (TPN) 415 volts, 63 Amps, 10KA complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole (SP) 240 volts, 40 to 63 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 32 Amps, 10KA ((C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 63 Amps, 10KA ((C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X4 sqmm multistranded copper conductor cable 1100 V with 1X4 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wire : Polycab/Anchor/Finolex

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 16 sqmm 2 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 25 sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

M & L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed. [Note : Punned thickness shall be measured and paid]

S&F for GI tubing 40 mm bore light grade laid in trenches/floors/ fixed to wall/poles for protection of cable with necessary fittings and FI clamps duly painted complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

Abrol construction co

M/S CANTILEVER ENGINEERS

M/S INDIAN ELECTRICAL

A V BUILDERS

M/S DUGGAL CONSTRUCTION CO

Walia trading co

naresh kumar sharma

v k engineers and builders

Raghbir chand

Shiva Builders