TENDER FOR CONSTRUCTION OF GALVALUME SHEET ROOFING FOR 500 KVA DG SET AT MAIN HOSPITAL AND FENCING WORK IN EE(C) CD II DIVISION

1. Dismantling of the existing lean mix floor concrete to the required size for fixing the vertical pipes etc.,all as directed at site of work and wherever required without damaging the nearby structures including collecting and depositing the debris within a lead of 50m for disposal including all labour, tools, equipments etc., complete

2. Earth work excavation in ordinary soil, sand, clay mixed with roots, boulders weighing individually less than 250 Kg, debris, rubbish etc., upto 1.50m depth as existing at site of work wherever required including dressing of sides ramming of bottom all as per relevant specification and as directed including conveying and depositing the excavated earth with in a lead of 50m , dewatering if required, including all labour, tools, tackles, storing, strutting equipments, fuel etc., complete

3. Providing and laying plain cement concrete of mix 1:4:8 in volumetric proportions (1 cement : 4 Crushed Stone sand : 8 Hard granite stone aggregate 40mm size graded down to 20mm size) for leveling course in foundations for fixing MS vertical pipe 100 mm dia and ISMB 150 etc. including shuttering, mixing, transporting, placing, ramming, curing, etc. including all labour, materials, equipment, tools, etc. complete.

4. Providing and laying plain cement concrete of mix 1:1.5:3 in volumetric proportions (1 cement : 1.5 Crushed stone sand : 3 Hard granite stone aggregate 20mm size graded down to 12mm size) for Pedestal of fixing M.S.vertical pipe 100 mm dia and ISMB 150 etc. below Ground level, including shuttering, mixing, transporting, placing, vibrating,curing etc. including all labour, materials, equipment, tools, etc. complete.

5. Supply, fabrication and erection of new Structural steel members for Roof Trusses, purlins, rafters etc. for roofing system / wall cladding and fixing of roof trusses in proper position in the vertical supports of 100mm dia MS pipe with MS Hollow section of size 60x40x3.2mm as purlins and MS Hollow section of size 80x40x3mm as rafters or nearest available higher size section with necessary Gusset Plates/ base plates, bolts and nuts including all accessories / consumables for proper completion of the work, all as per drawings, relevant specifications and as directed at site of work, including providing scaffolding, safety helmets, safety belts, safety shoes all equipment such as welding plants /Gast cutting plants, materials, labour, tools , transport , fuel , etc., complete.

6. Providing and fixing Galvanized Powder coated Colour corrugated Sheet 0.47mm thickness for Roof portion to the required size and fixing in proper position including providing necessary lapping/mittering the corners if necessary all accessories/consumables such as self threaded screws etc., for proper completion of work all as per drawings, relevant specifications and as directed at site of work ,including providing scaffolding, all materials, labour, tools, equipments, transport , fuel, safety helmets, safety belts, etc., complete..

7.Supplying, stretching and fixing G.I chain link fencing of 2m height with PVC coated sleeve of mesh size 50mm x 50mm, made out of 2.5mm G.I wire having total thickness of 4mm, tying to the vertical supports with the same PVC coated G.I wires of 4mm overall thickness including providing 8mm dia RTS rods fixed top and bottom horizontally throughout the fencing, all as directed at site of work and applying two coats of anti corrosive paint over a coat of primer for 8mm dia RTS rod including all labour, materials, tools, equipments, scaffolding, transport, fuel etc., complete. Note: - The cost of 8mm dia.RTS rods. will be paid under seperate item.

8. Supplying, fabricating and fixing in position of Main Gate of size 3000x2000 mm and wicket Gate of size 1200x2000mm both gates are made up of 16mm M.S. square rod as vertical member and MS flat of size 40x8mm as Horizontal member with necessary fittings including fixing the ISMB 150 section on both sides of Main Gate / wicket Gate with suitable pintel arrangements / hinges etc., including applying one coat of red oxide primer for Main Gate/wicket Gate all as directed at site of work and as shown in the drawing including all labour, materials. tools, equipments, transport, fuel welding plants/Gas cutting plant,brushes etc. complete.

9. Preparing the surfaces of the ceiling and plastering in CM 1:3(1Cement: 3 clean C.S.sand) 6-10mm thick to the required finish and wherever required curing etc., all as directed at site of work including all labour, materials , tools, scaffolding, equipments, curing etc., complete

10. Preparing the surfaces of existing ceiling and applying two coats of white wash using lovelycem of approved make to give an even shade and all as directed at site of work including providing scaffolding, all materials, labour, tools, equipments, brushes, etc. complete.

11. Preparing the surfaces of existing inner wall and applying two coats of Plastic emulsion paint of approved make, colour to give an even shade all as per Manufacturer;s specification and as directed at site of work including providing scaffolding, all materials, labour, tools, equipments, brushes, etc. complete.

12. Preparing the surfaces of existing exterior wall and applying with one coat of ACE (Acrylic copolymer emulsion paint ) of approved make, colour to give an even shade all as per Manufacturer;s specification and as directed at site of work including providing scaffolding, all materials, labour, tools, equipments, brushes, etc. complete

13. Preparing the surfaces of new steel members and applying two coats of synthetic enamel paint over a coat of red oxide prime of approved quality, colour to give an even shade all as directed at site of work including providing scaffolding, all materials, labour, brushes, tools, equipments, transport , fuel ,etc, complete. NOTE: 1. Necessary painting co-efficient shall be allowed as per Ch.P.T. engineering manual. 2. The above quantity is inclusive of painting co-efficient

14.Preparing the surfaces of new steel members and applying two coats of synthetic enamel paint of approved quality, colour to give an even shade all as directed at site of work including providing scaffolding, all materials, labour, brushes, tools, equipments, transport , fuel ,etc, complete. NOTE: 1. Necessary painting co-efficient shall be allowed as per Ch.P.T. engineering manual. 2. The above quantity is inclusive of painting co-efficient

15. Preparing the surfaces of existing wooden members and applying one coat of synthetic enamel paint of approved quality, colour to give an even shade all as directed at site of work including providing scaffolding, all materials, labour, brushes, tools, equipments, transport , fuel ,etc, complete. NOTE: 1. Necessary painting co-efficient shall be allowed as per Ch.P.T. engineering manual. 2. The above quantity is inclusive of painting co-efficient

GEES EPC SERVICES PVT. LTD.