Provision of Limited Height Subway (LHS) with EI (Make: Hitachi) in lieu of Existing Manned Level Crossing No. LC-357 at Km 661/19-21 between BAV-MMS Stations of KUR Division and Execution of PRIME Target Works in Khurda Road Division.

A1-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All

A2-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All

B1-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

B2-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

B3-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

C -SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR.

Item- 1 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

KHURDA ROAD DIVISION-S AND T/ECOR

1 1 Installation/Alteration/Phase working, Wiring, Station 1.00 1314621.00 1314621.00

testing and commissioning of complete

Electronic Interlocking System

(Distributed/Centerlized Configuration

System with Hot Stand by feature) supplied

as per Item Nos. 01 of Schedule-B-I including

transportation from Consignee's depot to site

of work. This includes execution of labour

portion, Interface relay wiring, erection of

relay racks, fixing of relays and associated

work in relay room, proper fixing of Operator

VDU Terminals etc (The Relays for interface

relays wiring will be supplied by Railways.

The Contractor shall supply all other

materials required for installation, wiring,

testing and commissioning). NOTE:- 1)

Installation & commissioning of Electronic

Interlocking is as per Section-H , Chapter-08.

2) If it is phase working, other than initial

phase design, supply of application logic

required for phase working should be done

by the Contractor agianst this item. 3) The

work includes manufacture/ fabrication,

supply and installation of SM's console and

side table extension as per site requirement

and as advised by site Engineer to

accomodate VDUs, other S&T equipments

and SM's stationary for operation of VDUs

and execution of day to day work for

operation of trains.

2 2 Factory acceptance test (FAT) with ECoR Station 1.00 700837.00 700837.00

officials, Only for Subsequent Phase working

not for Initial working.

3 3 Site Acceptance Testing(SAT) with ECoR Station 1.00 723923.00 723923.00

officials, Only for Subsequent Phase working

not for Initial working.

Schedule A2-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable)

Item- 2 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Alteration of existing panel, wiring and Station 1.00 42357.40 42357.40

testing and commissioning of Control

Panel[Operation-cum-Indication Console] as

per Specn. No.S/36/87 amendment-2,

complete with termination of cable, painting

and lettering as required. Railway will supply

Control Panel and multi core indoor cables

only. Tender shall supply Dominoes, buttons,

keys, counters, MS Angle/Flat, Hylum sheet,

MS clamps, Bolts andnuts, PVC pipes, Screws,

Sleeves, PVC cables, PVC pipes, PBT

terminals, Fuses, LEDs etc and all other

materials required for the work at his own

2 2 Alteration of wiring in existing Relay rack/ CT Numbers 1.00 28281.00 28281.00

rack/composite relay rack. This includes

supply of all types of wires, eyelets, nuts &

bolts, bunching material, ferrules, ARA

terminals, fuses & fuse blockes by the

contractor at his own cost. Lettering &

painting to be done by the contractor at his

own cost. Wire (RDSO Approved Sources) to

be inspected by the representative of

Railway before use.

KHURDA ROAD DIVISION-S AND T/ECOR

3 3 Wiring, testing and commissioning of overall Stn/IBH 1.00 140176.00 140176.00

circuits and ground gears of approved

interlocking arrangement as per approved

circuit diagram and Interlocking plan. This

also includes making corrections/alterations

in As Planned drawings and documents as

per the execution at site. This includes Free

home signal connection at site and SM's

office, telephone connection in the

tents/goomties and any other communication

arrangement for the Non interlocking at the

station or as decided by the representative of

Railway during non-interlocking. The

materials required for preparation of Free

Home indication board will be supplied by the

tenderer.This also includes painting and

lettering of gears. Telephone, VHF

Sets/Walkie Talkie sets will be supplied by

railway. Note: In case of IBS : It includes

overall testing and commissioning of IBS and

both the end stations associated with IBS

4 4 Miscellaneous arrangement for NI period Station 1.00 149624.00 149624.00

comprising of Provision of water-proof

temporary goomty/tent at both side of the

station yard and at central panel building.

Each goomties to be furnished with one iron

table, six chairs, emergency light and

mosquito repellant caps for NI staff, PA

system, crowbar men for operating point and

men for supplying water to tents.

5 5 Dismantling of existing LC gates and related Numbers 1.00 10461.00 10461.00

gears. This includes dismantling, stacking,

accountal of all the materials including

transportation of all the released materials to

the Railway store.

6 6 Transportation, excavation of pit, casting of Numbers 4.00 19438.00 77752.00

foundation, plastering and erection of Steel

Apparatus case (full size) with fixing of E-

Type lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/CON/SK/16. This includes earth work

and/or masonry work required for securing

the apparatus case as per site condition.

Railway will supply apparatus case with 'E'

type lock only from Railway stores at.

Tenderer will supply all wiring materials, PBT

Terminals, fuses, fuse blocks, bus bars, hylum

sheet ISI mark [6mm thickness], wood plank

board of good quality [minimum 3/4" thick,

Cement and transport all the materials to site

of work at his own cost. The wiring materials

such as wire coils, PBT terminals, fuses, fuse

block, etc. should be used from RDSO

approved sources.

7 7 Alteration of wiring in existing apparatus Numbers 4.00 3583.00 14332.00

cases full/half. This includes supply of all

materials in connection with alteration in

wiring. All the materials shall be supplied by

the contractor at his own cost. This includes

entry of cables, sand filling and masonry

work involved. Lettering and painting to be

done by the contractor at his own cost.

Railway shall supply only relays and relay

KHURDA ROAD DIVISION-S AND T/ECOR

8 8 Transportation of signal posts for multiple Numbers 2.00 20931.00 41862.00

aspect colour light signals, complete with

signal units, bases, ladders and other fittings,

excavation of pit, casting of cement concrete

foundation, plastering as per Drg.No

Con/SK/T/12, erection and fixing of complete

fittings of the 2/3/4 aspect signal/signal posts

including termination of cables, wiring, LED

fixing, signal testing and focusing. Name

plate & marker and all other materials shall

be provided by the contractor at his own

cost. Required cement shall be supplied by

the contractor. Arrangement of Screening to

be provided by the contractor if required as

instructed by site Engineer. Contractor shall

prepare jointly with Railway Engineer at site

and submit Signal Sighting report and Signal

test report as per approved format of

Railway. NOTE: (i) 50 % Payment shall be

released after erection of signal post.

Balance 50 % shall be released after

termination of cable, wiring, painting, testing

& focusing of signal. (ii) If foundation is

available at site 30% of the cost is to be

9 9 Laying of Signalling/4 Quad/ 6 Quad/ Power Kilometre 5.00 24389.00 121945.00

Cable/Telecom cables/ Jelly filled cables of all

sizes in excavated trench, through

GI/RCC/DWC pipes etc. wherever required.

This includes transportation of cables from

the stores to work site and transportation of

empty cable drums with left over cables from

site to the stores at. The length of cable laid

includes the length of cable coil for

termination purpose. NOTE: The cables are to

be carefully handled during loading, un-

loading and transportation to work site. Any

damage found in the cable after final testing,

in view of mishandling of cables, shall be

made good by the Tenderer. Cable should be

maggered before and after laying and

recorded in a register and submitted to the

10 10 Excavation of trenches of following depth and Kilometre 1.30 88821.00 115467.30

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [ii] 1.0 Meter

KHURDA ROAD DIVISION-S AND T/ECOR

11 11 Fixing of cable route marker as per drawing Numbers 24.00 706.00 16944.00

in" section-H" at a distance of 100 mtrs.

Along the trench and at places where the

cable route has taken diversion as per

instruction of site Engineer, this includes

casting of foundation at site and fixing of the

marker in the foundation made earlier at site

as per railway directives and specifications,

this includes proper curing of the structure,

All materials required for this like cement,

sand 15 mm chips and steel rod of ISI marks

should be supplied by the tenderer.

12 12 Horizontal direction drilling/boring without Metre 300.00 1515.72 454716.00

damage of surface of road/track formation.

The bore shall be 150 mm dia. and shall be

at the proper depth as per site conditions

decided by Enginerin-charge. The ground

level shall be considered ignoring the

bankheight of the bank of the road. The

length of the bore shall be minimum 04 Mtrs

long. This include insertion of different dia.

DWC/GI/HDPE pipes coupling etc as per

direction of Engineer-in-charge. NOTE: The

cost of pipe is not included in this item.

Contractor shall provide all material required

for boring and adequate nos. of labourers for

proper laying of cables in to the bore. Cable

shall be laid cautiously so that it should

notget damage due to rough handling and

pressure on cable.

13 13 Excavation of trenches in all kinds of soils Metre 70.00 335.00 23450.00

including soft rocky area and clearing of

track etc. to a depth of 1.0 M and width of

0.3 M for track crossing /pucca road/level

crossing gate/platform/station circulating

area or any other place as advised by site

Engineer including transportation and laying

of DWC/RCC/Split RCC/G.I. pipes with or

without coupler. This includes repairing of

track/pucca road/level crossing gate/

platform/station circulating area surface to

original position by ramming and concreting

wherever required soon after the work is

over. DWC/RCC/GI pipes shall be supplied by

the Railway. DWC pipes wherever required

shall be supplied in 6 Mtr. length and shall be

cut to size as per requirement. All other

materials including cement are to be supplied

by the contractor.

14 14 Excavation of trenches including clearing of Metre 30.00 255.00 7650.00

roots of trees etc., in rocky area up to a

depth to be indicated by Railway Engineer at

site as per the site condition [Minimum 0.6

meter] and width 0.3 Mts. at the bottom. This

includes concreting & plastering as per the

instructions of site Engineer and complete

back filling by digging earth from a lead of 30

Mtr. In case 0.8 meter depth or higher is

achieved no concreting is required, otherwise

concreting up to 100 mm thickness should be

done. All materials required for the above

works shall be supplied by the Contractor.

KHURDA ROAD DIVISION-S AND T/ECOR

15 15 Cable Duct behind the Relay room and Numbers 2.00 16729.00 33458.00

Goomties of size 1.8 M x1.8 M x 1.2 M to

keep cables entering into it consisting of

brick work of 254 mm thickness of proportion

1:6 with sand filling after coiling of cables.

The top of sand filling covered with

concreting of size 1.30 M x1.30 M and a

depth of 200 mm of proportion 1 : 1.5 : 3

outside of the duct should be plastered with

cement mortar 1 : 6 to achieve smooth

finishing. All materials including cement and

chips of size 40mm. and second class bricks

etc. to be supplied by the contractor.

16 16 Cutting of masonary floor/walls at station Numbers 2.00 6108.00 12216.00

building/ signal goomty/ Gate lodge at a

depth of 0.5 mtr. to 1.0 mtr a t places to be

indicated by site Engineer for entering of

cables inside the building. Only G.I pipes

supplied by Railway and all materials as

clamps, bolts & nuts as instructed by site

Engineer supplied by tenderer. This includes

repairing of masonary floors/walls after the

cables are taken inside. Cement, Sand

required for the work shall be supplied by the

tenderer and also transportation of G.I Pipe

from Store by the tenderer.

17 17 Trenching and fixing of G.I. pipes of different Metre 30.00 533.00 15990.00

sizes/DWC pipes in hard rocky area up to a

depth of 0.3 M to 0.6 M or at places as per

instructionof site Engineer and concreting [1

: 3 : 6] up to height of 100 mm above the

pipes. G.I. pipes with the socket/ DWC pipes

shall be supplied by the Railway. All other

materials required for the works shall be

supplied by the contractor. Note: [1] In case

of girder bridges, G.I. pipes shall be suitably

clamped by the contractor as advised by the

site Engineer. Clamps shall be supplied by

the contractor. [2] The work including

excavation of trenches in hard rock area up

to a depth of 0.3 M to 0.6 M and back filling,

ramming after completion of work where

ever required. [3] In case of concrete bridges

clearing of ballast for laying of pipes and re

arranging the Railway ballast after

completion of work shall be done by the

18 18 Supply, Transportation and Installation of Numbers 6.00 12306.00 73836.00

earth electrode (make TATA or Jindal as per

Rly. practice) including MS flat for signalling

equipments on lever frame, apparatus cases,

signal, relay racks, cable termination rcak,

block instrument etc. (supply & installation of

earth electrode as per drawing no.

RE/S&T/DRG/Tender/SK/398/94 for apparatus

cases, signal post & other equipments as per

instruction on earthing of S&T equipment.

Laying of earth lead mild steel flat of size

35mmx6mm and fixing of lead MS flat (make

TATA/Jindal or Similar) to earth electrode and

lever frame, signal post & apparatus cases as

per Drg. No. CORE/S&T/ALD/SK/591/2008,

592/2008 and 593/2008 respectively and

instructions on earthing at S&T equipment

and providing cement enclosure for earth

electrode as per drawing no.

RE/S&T/Sig./Tender/SK/13/85 Alt. A) NOTE:

This includes testing of earth value and

indicating the same on the Earth enclosure

by paint. Inspection by RITES.

KHURDA ROAD DIVISION-S AND T/ECOR

19 19 Supply, installation, testing and Numbers 1.00 61717.00 61717.00

commissioning of Maintenance free and

permanent earth as per RDSO Specification

No. RDSO/SPN/197 Version 1.0 and Technical

Specification as per section H, Chapter 8.

Inspection by RITES.

20 20 Fixing of relay bases and wiring, bunching, Per Relay 20.00 783.00 15660.00

fixing of relays, wiring in Old relay

racks/location box and also carrying out any

alteration in existing relay rack duly wiring

and connecting New to old and Old to old

relays by standard wires (RDSO Approved

Sources) as per Circuit diagram. Fuses of

bases, condensers, ND fuses, LED indicator &

its wiring for relay rack. All materials required

for this work will be supplied by the

contractor from RDSO Approved Sources.

Relays with accessories will be supplied by

21 21 Hiring of JCB machine (in good condition) for Hour 16.00 845.61 13529.76

levelling and dressing ground/dismantling

structures including disposal of debris

through dumpers etc. with contractor's

labour, JCB machine, machine operator, fuel

etc. The contractor shall arrange road permit

for vehicle for all the states of operation as

per instruction of engineer-incharge and

vehicle shall not be more than three years

old. payment shall be made for actual

working hours at site.

22 22 Supply, fitting & fixing of ply board 19mm Sqm 50.00 1684.47 84223.50

thick for cupboard, partition wall etc.

Inspection by representative of Sr.DSTE/KUR.

23 23 Transportation of OFC from the store of to Kilometre 0.50 25563.00 12781.50

work site with care, and pushing/ pulling OFC

through the HDPE pipes sealing of the duct

by simple plugs. The cable is to be laid by

mechanised means. At inaccessible places

where mechanised laying is not possible, the

cable is to be laid manually by pulling

through pre inserted rope. Empty cable

drums with or without leftover cable should

be returned to the store. This also includes

testing of cable drums by OTDR in the store

premises before transportation and

submission of results thereof.

24 24 Transportation of HDPE pipe from the store to Kilometre 0.50 15746.00 7873.00

the work site, laying of the same ( with 4mm

nylon rope,pre inserted inside the HDPE pipe)

in excavated trench/already laid GI/RCC

pipe/tubes,jointing, levelling and end sealing

the pipes. HDPE pipe, couplers and end caps

shall be supplied by the railways, Nylon rope

shall be supplied by the contractor.

25 25 Transportation and jointing (straight through Numbers 2.00 1591.00 3182.00

and derivation) of PIJF/quad cables size TSF-

IV as per Specn No. IRS: TC-31/96 & IRS

30/97. Jointing kits shall be supplied by the

Railway. All other materials shall be supplied

by the tenderer.

KHURDA ROAD DIVISION-S AND T/ECOR

26 26 Supply, transportation, and installation of Numbers 2.00 11156.00 22312.00

RCC joint chamber with two piece top cover

and bottom cover with hole for drainage and

cable entry as per drawing No.RCIL/ER/DRG-

02/06 (Section-H). This includes trenching for

joint pit, back filling and ramming of pit after

placing the joint closure and cable loop in the

chamber without causing damage to the

same and consolidation of soilas well as

disposal of excess soil. Inspection by

representative of Sr.DSTE/KUR.

27 27 Supply ,transportation & installation of Numbers 2.00 18027.00 36054.00

Optical Fibre cable joint enclosure and

splicing of OFC (24 Fibre) and testing. OFC

spicing shall be done in presence of Railway

Representative. Inspection by representative

of Sr.DSTE/KUR.

28 28 Transportation, excavation of pit, casting of Numbers 2.00 9742.00 19484.00

foundation, plastering and erection of Steel

Apparatus case (Half size) with fixing of E-

Type lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/Con/BBS/92/90. This includes earth work

and/or masonry work required for securing

the apparatus case as per site condition.

Railway will supply apparatus case with 'E'

type lock only. Tenderer shall supply all

wiring materials, PBT Terminals, fuses, fuse

blocks, bus bars, hylum sheet ISI mark [6mm

thickness], wood plank board of good quality

[minimum 3/4" thick, cement and any other

materials that are required for the work at his

own cost. Contractor has to transport all the

materials from store at his own cost to the

work site. The wiring materials such as wire

coils, PBT terminals, fuses, fuse block, etc.

should be used from RDSO approved

sources.1) Modification of inside

arrangement of Apparatus cases if required

for fixing of relays/transformers etc. shall be

done by the contractor. Extra shelf, if any,

shall be deposited to the Railway stores by

the contractor.2) All cables shall be

terminated by providing copper eyelet of

suitable size.Note:-(i) If location box

foundation is available at site 20% of the cost

is to be deducted.(ii) 40% payment shall be

released after erection of location boxes.

29 29 Submission of the final cable route plan after Route 0.30 2111.00 633.30

the cables are laid and commissioned Kilo

indicating clearly the exact position of the Meter

cable, joints, LB for emergency sockets and (RKM)

other critical materials with reference so

centre line of the nearest track. The final

cable route plan and drawings of the cable

terminations along with all relevant

particulars area to be submitted to the

Railways in original master form as well as 6

30 30 Hiring charges for 7.5 KVA DG Set including Job 2.00 1945.63 3891.26

manpower for operation and maintenance as

per direction of Engineer at site. Only HSD oil

is to be supplied b y Railw a y. Remaining all

other materials including transportation of

the DG set to the site is to be borne by the

contractor. (1 JOB=1 DG set for 1 day)

KHURDA ROAD DIVISION-S AND T/ECOR

commissioning & associated wiring for

temporary lighting with 1x28 Watt T5

FL/1X18 W or abo ve indoor type LED T8

fittings with lamp including manpower for

operation and maintenance as per direction

of Engineer at site. All materials including

fitting & wires etc. are to borne by the

contractor. (1 JOB= 1 Light for 1 day).

32 32 Painting, varnishing, numbering, lettering Station 1.00 38057.00 38057.00

and graphiting of all outdoor and indoor

signalling equipments over and above the

initial painting as per instruction of Railway

representative at site. This includes supply of

paints, varnish, graphites and any other

consumables by the contractor.

33 33 Supply and installation of Exothermic weld in Per Weld 250.00 1875.30 468825.00

earth strip and other side with Lug tightened

through nut-bolt, with supply of 1X16 sq mm

green multi strand copper power wire as per

IS:2465/1984 and IS:694:2010 or latest,

conductor each dia0.45+/-0.01 with

insulation thicknessof 1.2mm and nominal

conductor resistance of 1.127 ohms/KM and

test parameters as per RDSO spec No-IRS:S-

76/89 Ammend-3 copper lug 16sq mm both

side, 16sq mm cables will be laid normally on

layer of soft earth under the floor. The

cutting to be filled and finished with cement

concrete and plastering. The wire will be laid

in PVC pipe and this work is to be executed

as per direction of railway engineer at site as

per extent practise of ECOR. Supply items

will be inspected by RITES, whereas

execution will be carried out by the

representative of Sr. DSTE/KUR.

Schedule B1-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable)

Item- 3 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of Master telephone (One No.) with Set 1.00 112437.00 112437.00

voice recorder (Model No. GTM 124 or

similar), (II) slave telephones (3 nos.) (Model

No. GTM-909S or similar), (III) 24V Power

supply unit ( 01 no) Inspection by RDSO.

2 2 Supply of Magneto Telephone Desk type to Numbers 2.00 7317.00 14634.00

Specification No. IRS: TC-36/97 amd 2. or

IRS:TC 79/2000 Amdt. 4 as per Railway

requirment. Inspection by the Representative

of Sr.DSTE/KUR.

3 3 Supply of Steel Apparatus case 'large Size' as Numbers 4.00 42507.00 170028.00

per Drg. No - CON/SK/1/1/86 and Spec.No.

IRS:S-10/78 (adv) with latest amnd. with "E"

type lock and key of ward No-32 with handle.

Inspection by RITES.

4 4 Supply of Signal colour light multi unit as per Numbers 2.00 29161.00 58322.00

specification No: IRS: S-26/64 with latest

amendment as per RDSO Spec No.

RDSO/SPN/153/2011 long range working on

110 V- AC 50 Hz complete 3-Aspect suitable

for 140 mm dia. post as per Drg.No:SA-23002

A/M [Adv]. Inspection by RITES.

KHURDA ROAD DIVISION-S AND T/ECOR

5 5 Supply of 4.6 Mts CLS tubular steel post Numbers 2.00 11663.00 23326.00

specification No. IRS: S-6/81 with latest Amnd

to suit 140 mm dia base. Inspection by the

6 6 Supply of Ladder 4.5 meter for CLS post as Numbers 2.00 8181.00 16362.00

per Drg. No. SA: 23153 [Adv] Alt-1,

specification No. IRS: S-10/78 (with latest

Amendment) consisting of ladder base,

platform and guarding, ladder support

complete. Inspection by the RITES.

7 7 Supply of Signal Base 140 mm dia [Type Numbers 2.00 5024.00 10048.00

tube] Drg. No. S-2011/M. Inspection by the

8 8 Supply of double walled corrugated pipe 6 Numbers 14.00 4117.00 57638.00

mtr in length, 120 mm outer dia and 103 mm

inner dia, w i t h one suitable coupler

conforming to RDSO Specification No.

RDSO/SPN/204/2011 Version 1.1 Amdt 1 or

latest for under ground cable protection .

C o l o u r- O r a n g e . Inspection by the

Representative of Sr.DSTE/KUR. Note: If

required, the DWC pipe shall be supplied split

9 9 Supply of Perforated G.I. pipe of 100 mm dia Metre 30.00 1889.00 56670.00

with socket. G.I. pipe of make TATA/JINDAL

shall be as per IS: 1239 part-I/2004

Specification for medium gauge and shall be

perforated by drilling 7 mm dia holes length

wise in zig-zag manner staggered at a

distance of 300 mm. Inspection by the

Representative of Sr.DSTE/KUR.

10 10 Supply of cable route tracer with Integrated Numbers 1.00 451828.60 451828.60

GPS and Bluetooth, Live GPS data transfer

with Mobile App, through BT, User

configurable frequency and Current direction

indication & 10W Transmitter with minimum

500mA output current and 90V visible on

display, with rechargeable Battery.

Specification as per section H. Make:

adiodetection (RD8200G) or similar. 3 years

OEM warranty. Inspection by representative

of Sr.DSTE/KUR..

11 11 Supply of Permanently lubricated two layer Kilometre 0.50 132496.00 66248.00

type HDPE duct, outer dia 40 mm, inner dia

33 mm with three end plugs and two

couplers for every Km length of pipe in

length of 500 m confirming to RDSO Spec.

No. RDSO/SPN/TC/45/2013.Rev.2.0

Amendment 2.0 or latest. Inspection by

representative of Sr.DSTE/KUR. Note: The

HDPE Duct should be pre inserted with 4 mm

nylon rope, inside the HDPE Duct.

12 12 Supply of Thermo shrink jointing kit for Numbers 6.00 6143.00 36858.00

underground cable as per Specn No. IRS: TC-

77/2012 [Rev.3] Amd 3. (Cable jointing kit

shall be procured from RDSO approved

sources only). Inspection by the RDSO.

13 13 Supply of Steel Apparatus case 'Half Size' as Numbers 2.00 25868.00 51736.00

per rg.No.S&T/CON/BBS/92/90 with 'E' type

lock & Key. Ward No. 32. Inspection by RITES.

14 14 Hand Held 200 Khz Digital Multimeter . Numbers 2.00 40592.00 81184.00

MAKE- FLUKE/ YOKOWAGA .MakeiBrand:-

FLUKE 87V. Inspection by the Representative

of Sr.DSTE/KUR.

KHURDA ROAD DIVISION-S AND T/ECOR

15 15 Supply of ELECTRICAL INSULATING RUBBER Numbers 1000.00 1203.60 1203600.00

MATS AS PER IS STANDARD IS 15652:2006

OR LATEST. SIZE - 3MM (THICKNESS) X 1 MTR

(WIDTH) X 2 MTR (LENGTH), MAT TYPE -

CLASS C, MAXIMUM USE VOLTAGE - 33 KV AC

(RMS) & 240V DC, DIELECTRIC STRENGTH 65

KV AC (RMS), COLOUR: BLACK, ANTI SKID

DESIGN CHECKRED. MAKES DURATUF,

RAYCHEM & MARVEL VINYLS or similar Make

(Warranty Period : Upto 30 months from the

date of delivery.). Inspection by RITES.

16 16 Provision of Cement concrete enclosure for Numbers 2500.00 481.35 1203375.00

Earth electrode as per Drawing No. S&T/C-

36(NKG). This includes supply of all materials

by the contractor duly inspected by

consignee. Inspection by RITES.

TPRA).Compatible with Global, Make:Global

Device or similar. Inspection by RITES.

18 18 Supply of lntel Core i5 All in One PC with 23.8 Numbers 93.00 57985.00 5392605.00

lnch Display/ Windows 11 Home,

Specification as per Annexure-AB. Inspection

19 19 Supply of Interactive UPS with AVR of rating Numbers 93.00 3905.72 363231.96

1.0KVA with warranty of 03 years,

Specification as per Annexure-AC. Inspection

by representative of Sr.DSTE/KUR.

20 20 Supply of Hp Multi function machines Mfm on Numbers 93.00 26555.00 2469615.00

site OEM warranty 03 year. Specification as

per Annexure-AD. Inspection by RITES.

21 21 Supply of Super gasketing compound corium Numbers 200.00 11670.00 2334000.00

Z-190 of 200 ml cane make: corium zl

Enecon/Lupromax or similar as per technical

document attached. Make- Corium Z190

(Warranty Period : Upto 12 months from the

date of delivery.). Inspection by RITES.

22 22 Supply of DC Motor 110 Volts with Gear Box Numbers 40.00 27718.20 1108728.00

IP67 type 400V AC Immunity for Electric Point

Machines (IRS Type ) as per IRS: S 37-2022

Version 2.0. (Warranty Period : Upto 60

months from the date of delivery.).

Inspection by RITES.

23 23 Supply of Insulation resistance tester 500V Numbers 1.00 17857.00 17857.00

DC 500 Mega Ohms hand generator type

metal body to Spec. no. IS:2992 make WACO.

Inspection by the Representative of

24 24 Supply of AC/DC Digital clamp meter Fluke- Numbers 1.00 83661.00 83661.00

376 or similar. Inspection by the

Representative of Sr.DSTE/KUR.

Schedule B2-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

Schedule 4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item Directory - Not

Item- 4 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of LED signal lamps RED aspect for Numbers 5.00 8401.60 42008.00

main color light signals for railway signaling

as per RDSO.( Warranty Period : Upto 60

months from the date of supply). Inspection

KHURDA ROAD DIVISION-S AND T/ECOR

2 2 Supply of Integrated LED Signal for YELLOW Numbers 5.00 8401.60 42008.00

aspect as per RDSO Specification No.

RDSO/SPN/199/2010Rev1.1 or latest. (

Warranty Period : Upto 60 months from the

date of supply).Inspection by RDSO.

3 3 Supply of Integrated LED Signal for GREEN Numbers 5.00 9581.60 47908.00

aspect as per RDSO Specification No.

RDSO/SPN/199/2010Rev1.1 or latest. (

Warranty Period : Upto 60 months from the

date of supply). Inspection by RDSO.

Schedule B3-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

Schedule 4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item Directory - Not

Applicable) (Item Directory - Not Applicable)

Item- 5 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of Relay AC Immune, plug-in type, Numbers 15.00 6428.00 96420.00

style 'QNA1', Neutral line, 24V DC 8F/8B

contacts, Front and back contacts metal to

carbon, complete with plug board, retaining

clip and connectors conforming to

BRS:931A,IRS : S - 60, IRS : S - 34, IRS : S - 23

(As applicable). Interlocking code : ABDGH.

Inspection by RDSO.

2 2 Relay plug in type, Style AC-LED: ALL aspect, Numbers 15.00 7878.00 118170.00

AC lamp proving Relay unit within built

current transformer type, slow release

neutral line relay, 4F/4B contact , front and

back contact metal to carbon shall be

suitable for working in series with 110V AC,

LED signal lamp rated at 15W conforming to

RDSO Spec No- STS/E/Relay/AC lit

LED/signal/09-2002, Amdt. 1, BRS : 941A ,

IRS : S :3 4 & IRS : S : 23 {as applicable}. The

interlocking code for this unit shall be

ABDHK. Inspection by RDSO.

Schedule C -SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE OF:1.All taxes.,

2.Supply of sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of

Schedule materials to site., 4.Transportation of released materials from one site to another site or store of

concerned SSES/(In-charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item

Directory - Not Applicable) (Item Directory - Not Applicable)

Item- 6 SUPPLY & EXECUTION OF DRAWING WORK

S No. Item Description of Item Unit Qty Rate Amount

1 1 Compilation, preparation, correction, Per Page 100.00 25.00 2500.00

updating, printing and supply of Final station

working rules with contractor's stationery,

tools, plants and materials. Note: Final SWR

to be submitted in 2 sets for each station.

2 2 Printing and supply of approved SWR with Per Page 100.00 4.00 400.00

contractor's stationery, tools, plants and

materials. Note: Approved SWR to be

submitted in 6 copies for each station.

3 3 Design of SIP & submission of Three paper Set 1.00 36520.00 36520.00

copies for approval.For a Four-Line Station

4 4 Design of SWRD & submission of Three paper Set 1.00 17628.00 17628.00

copies for approval.For a Four-Line Station

5 5 Alteration of Existing SWRD & submission of Station 1.00 2596.00 2596.00

Three paper copies for approval.For a Four-

6 6 Design of Cable Route Plan (Distant to Set 1.00 8815.00 8815.00

Distant) & submission of Three paper copies

for approval. For a Four-Line Station

KHURDA ROAD DIVISION-S AND T/ECOR

7 7 Supply of Original Tracing of SIP after Numbers 1.00 730.00 730.00

incorporating all the corrections. For a Four-

8 8 Supply of Original Tracing of SWRD after Numbers 1.00 528.00 528.00

incorporating all the corrections. For a Four-

9 9 Supply of Original Tracing of Cable Route Numbers 1.00 1411.00 1411.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Four-Line Station

10 10 Supply of Original Tracing of Location Box Station 1.00 2644.00 2644.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Four-Line Station

11 11 Supply of Amonia Print of Approved SIP .For a Numbers 6.00 44.00 264.00

Four-Line Station

12 12 Supply of Amonia Print of Approved SWRD. Numbers 6.00 44.00 264.00

For a Four-Line Station

13 13 Supply of Amonia Print of Approved Cable Numbers 6.00 44.00 264.00

Route Plan(Distant to Distant). For a Four-

14 14 Alteration of Existing RCC & submission of Station 1.00 2596.00 2596.00

Three paper copies for approval. For a Four-

15 15 Design of RCC & submission of Three paper Set 6.00 17628.00 105768.00

copies for approval.For a Four-Line Station

16 16 Supply of Original Tracing of RCC after Numbers 6.00 705.00 4230.00

incorporating all the corrections. For a Four-

17 17 Supply of Amonia Print of Approved RCC. For Numbers 6.00 44.00 264.00

a Four-Line Station

18 18 Alteration of Existing Circuit Diagrams Sheet 100.00 350.00 35000.00

consisting of the items as mentioned below &

submission of Three paper copies for

approval. (i) Wiring Diagrams, (ii) Relay

Disposition Charts, (iii ) Contact Analysis and

Fuse Particulars, (iv) Panel Termination

Chart, (v) CT Rack Particulars & (vi) Input &

Output Bit Chart for EI Systems

19 19 Design of Cable Distribution Plan & Set 1.00 7077.00 7077.00

submission of Three paper copies for

approval. For a Four-Line Station

20 20 Supply of Original Tracing of Cable Numbers 1.00 1411.00 1411.00

Distribution Plan after incorporating all the

corrections. For a Four-Line Station

21 21 Supply of Original Tracing of Goomty Station 1.00 3878.00 3878.00

Drawings (Including Relay Disposition Chart,

Contact Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc) after

incorporating all the corrections. For a Four-

22 22 Supply of Amonia Print of Approved Circuit Station 1.00 4583.00 4583.00

Diagrams consisting of the items as

mentioned below. (i) Wiring Diagrams, (ii)

Relay Disposition Charts, (iii ) Contact

Analysis and Fuse Particulars, (iv) Panel

Termination Chart & (v) CT Rack Particulars.

For a Four-Line Station

23 23 Supply of Amonia Print of Approved Goomty Station 1.00 705.00 705.00

Drawings ((Including Relay Disposition Chart,

Contact Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc). For a Four-

24 24 Alteration of Existing Location Box Drawings Sheet 50.00 451.00 22550.00

(Including Contact Analysis, Fuse Particulars

etc) and submission of Three paper copies for

KHURDA ROAD DIVISION-S AND T/ECOR

25 25 Alteration of Existing Goomty Drawings Sheet 20.00 901.00 18020.00

(Including Relay Disposition Chart, Contact

Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc) and

submission of Three paper copies for

26 26 Supply of Original Tracing in A-3 Size. NOTE:- Sheet 50.00 71.00 3550.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size.

27 27 Supply of Amonia Prints in A-3 Size. NOTE:- Sheet 100.00 19.00 1900.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size.