SPECIAL REPAIR TO BLD NO P-22 AND PROVN OF MT SHED FOR A VEHICLE AT NABHA UNDER GE(S) PATIALA

Amount

'Notes: (i) Please refer Schedule 'A' Notes of tender documents.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc. or for shafts, wells cesspits manholes, pier holes,etc. n exc 10 sq on plan & getting out in soft/losses soil complete all as specified and directed.

M&L dor PCC (1:2:4) type B-2, (using, 40mm graded stone aggregate) as in foundation, mass fillings for posts/struts etc complete all as specified and directed

S & F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws complete all as specified and directed.

S&F for rolled sections as in main and cross beams, hip and jack rafters purlins, where connected to common rafters and running rails and guides for slinding doors, fixed with angle cleats or other connecting plates to Fe-290 (Gde E-165) complete all as specified and directed.

S&F plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new steel surfaces of of any description not otherwise described over 10cm width or grith including prepartion of surface including one coat of red oxide primer complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches complete all as specified and directed.

Removing excavated soil to a distance n,exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified.

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

M & L for 15mm thick ( in two layers of 10mm and 5mm thickness) cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finished complete all as specified and directed Note : Water proofing compound shall be measured and paid saparately under item.

M&L 10mm thick cement plastering in cement mortar Cement Mortar 1:6 finishing the surface even and smooth without using extra cement complete all as specified and directed.

Complete removal of existing treatment of any type/description such as distempering work ,internal emulsion etc from internal/external surfaces of walls & ceiling with mechanical means/grinder including removal of material from site complete all as specified and directed.

M&L Preparation of new plastered or unplastered surfaces of walls, two coats of cement base paint complete all as specified and directed.

M&L prepration of new plastered or unplastered surface of walls and applying two coats of distemper oil emultion over complete all as specified and directed

Supplying & applying for two component elastomeric acrylic polymer modified cementitious waterproofing coating on Brick level, SmartCare Damp Block 2K or approved equivalent, having 100% elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per ASTMC1202, crack bridging up to 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI, will be apply on both Positive & Negative side and resist up to 5 Bars of Hydrostatic Pressure. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc. After coating will sprinkle Sand on the coating then apply plaster on the coating which is in contractor scope, complete all as specified and directed.

Supply only integral water proofing compound ISI marked.

Rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for Preparation of new plastered or unplastered surfaces applying three coat of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparing old plastered surfaces of ceilings and applying one coat of white wash in all as specified and as directed.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.

All as per srl item No 21 hereinbefore but n. exc 1.5 sqm each complete all as specified and directed.

S&F Powder coated Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with single rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts ,filling PCC (1:3:6 Co) in chowkhats , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 105x 60mm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified and directed ( Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item)

S&F Powder coated Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts ,filling PCC (1:3:6 Co) in chowkhats , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 125x 60mm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified and directed. Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item

M&L Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed.

S&F 35mm thick plain framed (Factory made) Panelled shutters of 2nd class HW with lock rail and panels of 9mm B.W.P commercial ply including beading on the facing side of shutters as per SSR Part I clause No 8.17.5. The size of rail and stiles as per IS 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm 2nd class hard wood Glazed and skeleton shutters, 2nd class hard wood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Aluminium 200mm anodised , barrel tower bolt of extruded complete all as specified and directed

Aluminium anodised sliding door bolt of size 250mm, stove enamelled black with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts complete all as specified and as directed.

S&F Aluminium handles 125mm cast type , anodised complete all as specified and directd.

S&F Mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and directed.

S&F in repair300 mm long MS rat tail pattern spring hinge including roller and roller plate, complete all as specified and directed.

S&F Floor door stoper of aluminum alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and as directed.

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows complete all as specified and directed.

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beed 20mm size complete all as specified and as directed.

S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples all as specified and directied

M&L for preparing of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel pain and one coat of pink primer complete all as specified and directed.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed.

M&L for Ceramic floor tiles of 7 to 8mm thick area of each tile exc0.18sqm but not exc0.38sqm in floor etc set and jointed in neat cement lurry and pointed in white cement to match over and including 15mm thick screed bed in Cement Mortar (1:4) laid in complete all as specified and directed.

M&L for Non Skid coloured tiles 7 to 8(square/rectangular) area of each tile ecxc 0.06Sqm but not exc 0.11sqm in flooring etc set and jointed in neat cement lurry and pointed in white cement to match over and including 15mm thick screed bed in Cement Mortar (1:4) laid in complete all as specified and directed.

S&F for coloured glazed ceramic tiles (300 x 600 mm) x 7mm or (300 x400 mm)X7mm thick as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed.

Taking Up or down steel tubing of size 15mm bore and removal to store complete all as specified and directed.

Taking Up or down steel tubing of size 20mm bore and removal to store complete all as specified and directed.

Supply and laying of 20mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed.

Supply and laying of 25mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed.

S&F mild steel chromium plated 20mm curtain rod with fixing brackets, stops rollerss complete incl fixing brackets, stops etc all as specified & directed as in repair . (For the purpose of mesurement and payment running length of curtain rod only shall be considered.)

Dismantling of brick tiles or terracing tiles single layar on roofs complete all as specified and directed.

Demolation of mud puska and removing on roof any thickness complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 using 12.5 mm graded crushed stone aggregates as in padding over roof maintaining a slope of 1:100 using water proofing compound finish even and smooth without using extra cement complete all as specified and directed.

M&L for the following roof treatment. (a) Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick weight not less than 3.60kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt, fixed as per manufacturer’s instructions complete all as specified and directed. (b) Applying one coat of bituminous primer confirming to IS-3384 @ 0.3 Ltr/Sqm. (c) Applying one coat of aluminium paint over APP membrane @ 0.50 litres per Sqm all as specified and directed. (d) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per square metre including cleaning the surfaces complete all as specified and directed.

S&F 30mm thick PVC door factory made solid panell shutters concisting of frame made out of MS tubes for top and bottom rails, MS frames shall be covered with hit moulded plain coulour PVC 'C' chanel having a PVC sheet strip of 20mm width stuck in side with screws complete all as specified and directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixed in opening complete all as specified and directed.

S&F 'PVC(SWR) Floor trap 75mm plain with CP grating including jointing to wate pipe with solvent cement complete all as specified and directed..

PVC ( SWR) rain water pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete as as pecified including flat iror clamps 25x3mm complete all as specified including taking out old damaged AC rain water pipes.

PVC (SWR) bends of any radius for 110 mmdia rain water pipes with rubber ring joints a complete all as specified and directed.

Rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position incl demolition of exisiting Rcc tank and incl 20 mm bore ball brass valves high pressure with polythene float and fly nut all as specified in SSR Part-1. complete all as specified and directed.

S&F in Repair Bib taps for 15 mm dia bore pipe cast copper alloy cromium plated with capstain head screwed down for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in Repair Pillar taps hot and cold mixture Cast copper alloy fancy type 15mm bore , with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts scrrewed for iron pipe and fixed complete all as specified and directed.

S&F in Repair stop cock cast copper alloy chromium plated fancy type ,high pressure with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipe after taking down old stop cock of any description complete all as specified and directed.

S&F in Repair Angle stop valve(Concealed type) cast copper alloy chromium plated with capstan head , long shank and cup screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipeafter taking down old stop cock of any description complete all as specified and directed.

S&F in Repair 20mm Stop valves/ gate valve , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in Repair 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and directed.

S&F Viterous china, wash hand basin, white, flat back, size 550x400mm including PVC waste pipe 32mm bore and mild steel brackets, fixed all in repairs, including cutting for or pinning in brackets complete all as specified and directed.

Tubular towel rail, CP 20mm dia, 60cm long between flanges fixed in repairs complete all as specified and directed.

S&F in repairs low level flushing cistern of PVC 10 ltr capicity incl 45cm long PVC connection with brass nut at both ends, 15 dia stop cock cast copper alloy,screwed both ends , high pressure(wt not less than as specified in SSR), PVC flush pipe 32 mm bore complete all as specified and directed.

S&F viterous china ware wash down water closet Orrisa pattern size 580x440mm white with integral foot rests including connection to traps and to flushing pipe, anti syphonage pipe complete fixed in repair.

Hard core of broken bricks of gauge n exc. 63 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface complete all as specified and directed.

PCC (1:3:6), 50mm thick as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement complete all as specified and directed.

S&F Machine cut Kota stone slab flooring 20mm (+2mm) thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 25mm thick cement concrete type B-0 (12.5mm graded aggregate) complete all as specified and directed.

All as per item No 73 here in before on vertical surfaces as in skirting/dado of size as required at site but excluding 25mm thick PCC complete all as specified and directed.

S&F for machine pressed precast concrete inter locking paver block any shape and size made of M-35 grade concrete (with grey cement and no pigment) of 60mm thickness with 6mm top layer of anti abrasive material laid over 25mm thick (compacted) fine sieved sand complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation all as per specified and directed

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring. complete all as specified and directed.

S&F for 'PVC enclosed case (cabin type) with cover and looking mirror over it with two shelves in it complete all as specified and fixed with screws on wall.

S&F cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floor of 100 mm bore with sand cast paper complete all as specified and directed.

S&F cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floor of 75mm bore with sand cast paper complete all as specified and directed.

S&F cast iron 100mm sand cast vent cowl with cement joints bore with sand cast paper complete all as specified and directed.

S&F CI floor trap with grating including jointing to waste pipe in neat cement 75 mm dia fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S&F CI P & S trap with grating including jointing to waste pipe in neat cement 100 mm dia fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

Demolition and breaking up 150mm drain pipes set in cement mortar (salt glazed stoneware/asbestos cement/reinforced) and removal of debris to low lying area to a distance not exceeding 100m, complete all as specified and directed.

Reinforced concrete pipes, class NP2 laid and jointed complete with collars bore in pipes 150mm complete all as specified and directed.

M & L for150mm bore, cement concrete bed 1:3:6 type C2, using 40mm graded stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in deep and getting out in hard / dense soil for foundations, etc or for shafts, wells, cesspits, manholes, pier holes, etc complete all as specified and directed.

Removing excavated material(soil) to a distance not exc 50mm and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

M & L for PCC 1:2:4, type B1, using 20mm size graded stone agregates as in bands, copings, etc., including necessary formwork complete as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soils complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quions, arches, pillers, etc complete all as specified and directed.

M&L for brick work in cement mortar 1:4 with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius for manhole and septic tank/soakage well repair work complete all as specified and directed.

Demolition of reinforced cement concrete of any description (Reinforecement cut as required to facilitate demolition )complete all as specified and directed.

M&L for reinforcement cement concrete (Normal mix )1:2:4 Type B1 (20mm graded aggregate) as in slab support on wall , beams and collums in floor roof landing balconies deck slab and in shelves and the like complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor and roof beams ,lintels beam ,cantilevers ,shelves including supports ,overhangs and similar work , for rough finished flat surfaces complete all as specified and directed.

S&f Coolar stand Joist, channel, angle, or tee sections, fixed independently, without connecting plates, conforming to Fe 410-W (Gde-E-250) quality -A complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L anodised aluminium snap grid false ceiling of grid size 605x605mm consisting of aluminium main and "T' sections of size 25x35x1.5mm thick and wall angles of size 25x 25x 1.5 mm thick suspended with GI wire suspenders of 6mm dia of suitable length and 8-10 mm thick gypsum board, 60x60 cm size fixed with staples on snap grid complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L for point wiring with 1.50 sqmm in copper conductor cable ( multistrand) FRLS single core PVC insulated cable in and including PVC concealed conduit ( ISI Marked) of heavy duly with all accessories ie PVC gutties etc terminated in sunken/pressed metal flush box and white modular cover plate with frame for mounting of switches /sockets/ fan regulators etc and continuous earth wire 1.5 Sqmm copper cable PVC insulated FRLS controlled by one switch for one light/fan/sockets point/ complete all as specified and directed. in ceiling Portion surface conduit wiring to be done. . Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.iii) Neccessary cutting chasing wherever required and making good the disturbed surface shall be part of job at no extra cost.

All as per item No 101 above, but for one 3/5 pin socket outlet 5 Amp on independent board complete all as specified and as directed.

All as per item No 101 above, but for one 3/5 pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed.

All as per serial item No 101 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed.

M&L for Modular switch 1 way 6A, 1 module complete all as specified and directed.

M&L for Modular switch 1 way 16A, 1 module type complete all as specified and directed.

M&L for Modular Socket, 6A - 5 pin, 2 module type complete all as specified and directed

M&L for Modular Socket 6A/16A - 2/3 pin, 2 module type complete all as specified and directed.

M & L for Fan step regulator, 120W - 1 module complete all as specified and directed.

S&Fin replacement of existing Unsv FTL with new techonlgy ultra bright led tubelight with aluminium heat sink & polycarbonate diffuser having high efficacy of capacity 20 Watt Warm White with BOX TYPE Pre-coated CRCA body, heavy duty regal Batten for LED tube universal batten for G13 t8 lamps including neccesary fitting on wall and making electric connection from ceiling rose to connector with suitable size of electric cable and making good the disturbed surface complete all as specified and directed.

S&F in replacement of LED 10 Watt, 2 feet long, Cool day light with NEO Batten10 W 6500K having high efficiency Cat No. LHEXACP7IN1W010. makes as mentioned in Appendix 'B' incl necessary electric conection complete all as specified and directed.

S&F in replacement of LED fitting 28 Watt complete with all accessories incl cost of lamp & driver, suitable for 2x2 feet false ceiling panel complete all as specified and directed.

S & F new generation energy saving and environmental friendly long life LED building security light 1x35 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with suitable dia light grade GI pipe bend to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed.

M&L for ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed.

M&L for replacement of existing earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate complete all as specified and directed and shown in EP-3 of SSR Part-I

M&L for replacement of existing earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to GI earth strip 32x6 mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I complete all as specified and directed.

S&F metal body exhaust fans AC single phase 230/ 240 V of size 450 mm sweep with louver . Note: Fixing of Exhaust Fan on wall with suitable size anchor bolt , making hole in wall for groutng and making good the disturbed surface including plaster work shall be part of job at no extra cost complete all as specified and directed.

S&F metal body exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver . Note: Fixing of Exhaust Fan on wall with suitable size anchor bolt all as specified and directed.

S&F Vertical three phase MCB distribution board powder coated double door flush mounted complete with locking arrangement suitable for 4 way VTPN as per IS - 8623, IP-54 protection, with MCCB of capacity 63 Amp FP, 16 KA as incomers and MCB's as out going with rated bus bar 200 Amp link 230 volt (Note: (i) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(ii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped.(iii) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (Cost of MCCB incl in the item of rate) complete all as specified and directed.

S&F Vertical three phase MCB distribution board powder coated double door flush mounted complete with locking arrangement suitable for 8 way VTPN as per IS - 8623, IP-54 protection, with MCCB of capacity 100 Amp FP, 16 KA as incomers and MCB's as out going with rated bus bar 200 Amp link 230 volt (Note: (i) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(ii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped.(iii) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (Cost of MCCB incl in the item of rate) complete all as specified and directed.

S&F Vertical three phase MCB distribution board powder coated double door flush mounted complete with locking arrangement suitable for 12 way VTPN as per IS - 8623, IP-54 protection, with MCCB of capacity 125 Amp FP, 25 KA as incomers and MCB's as out going with rated bus bar 200 Amp link 230 volt (Note: (i) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(ii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped.(iii) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (Cost of MCCB incl in the item of rate)

S&F MCCB 63 Amps 4 pole, 16 KA, 415 volts grade with thermal magnetic relaese type all as specified and directed.

S&F MCCB 100 Amps 4 pole, 16 KA, 415 volts grade with thermal magnetic relaese type all as specified and directed.

S&F MCCB 125 Amps 4 pole, 25 KA, 415 volts grade with thermal magnetic relaese type all as specified and directed.

S&Fin replacement of existing Unsv Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type as per IP-54 protection with 200 amp rated bus bar. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job.

S&F in replacement of existing Unsv Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 12 way double door type as per IP-54 protection with 200 amp rated bus bar complete all as specified and directed.. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job .

S&F in replacement of MCB SP up to 6-32 Amp complete all as specified and directed.

S&F in replacement of MCB SPN 6-32 Amp complete all as specified and directed.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x10 sqmm ( line conductor) & 1x10 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth . (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size . (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x6 sqmm ( line conductor) & 1x6 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth . (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size . (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

S&F in replacement of existing Unsv Plug & Socket Box (sheet metal) with PVC Plug, SPN 20 Amps for ACs. Model No. - DHDPHSN020 complete all as specified and directed.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x4 sqmm ( line conductor) & 1x4 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth . (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size . (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

S&F Wall mounted fan 450 mm sweep, 72 CFM, 1350 rpm, 230/240 volts PVC body with 4/5 step speed control, 3 blades type complete all as specified and directed.

S&F ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 63 Amps complete all as specified and directed.

Supply & lay in replacement of existing Unsv XLPE insulated, armoured heavy dutyelectric cable with aluminium conductor, 1100 volt grade of crosssectional area 25 Sqmm 3.5 Core complete all as specified and directed.

Excavating in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for sand cushioning with dry river sand in trenches for cushioning of underground cable line including spreading, leveling, well ramming completed all as specified and directed.

S&F well burnt sub class ‘B’ bricks. ( designated 75) locally available best quality laid dry in trenches for protection of underground cable all as specified and directed.

M&L for replacement of GI tubing light grade 50 mm bore for passing through cables under the floor, along the wall or along the pole complete all as specified and directed.

RINKU BROTHERS (BID ID -3117727)

m/s k.k. construction co. (BID ID -3117257)