Rehabilitation of Khanpur Disty from K.M. 0.000 to 10.300 (Tail)

Amount

Lining with design mix concrete of grade M-15 with minimum cement content 240kg/cum, 75mm thick in curve portion and side slope manually including 10 mm thick cement plaster 1:6, form work, dressing and preparation of sub grade HSR Item No. 14.10 (As per analysis of rate)

Providing and laying in position ready mixed plain cement concrete M-15, with cement content as per approved design mix andmanufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuousagitated mixer, manufactured as per mix design of specifiedgrade for plain cement concrete work, including pumping ofR.M.C. from transit mixer to site of laying and curing, excludingthe cost of centering, shuttering and finishing, including cost ofcuring, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of theEngineer-in-charge.(Note :- Less cement used as per design mix is recoverable. However no extra payment shall be made if excess cement is used as per design mix for sleepers). M-15 grade plain cement concrete (cement content considered @ 240kg/cum) as per HSR item No. 6.22.1.2

Brick work in 1:4 ( 1 cement 4 course sand) mortar with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth complete as per HSR. 7.21.1) @ (4135)/cum

E/Work excavation in foundation of structue as per drawing and technical specifications i/c setting out, construction of shoring & bracing, removal of stumps and other deterious matter, dressing of sides & bottom and back filling with approved materials as per Specifications by manual means in ordinary all lead and lift and rolling around structure depth complete as per HSR 4.12.1

Providing & laying in position Cement concrete 1:4:8 with 8 graded sone aggregate of 40 mm size in foundation and plinth excluding centering & shuttering complete in all respect as per HSR 6.1.b

Filling expansion joints, with bitumen impregnanted hot pour, 12 mm wide as per HSR item No. 6.58

10 mm thick cement sand plaster (1:5 as per analysis of rate) (HSR 11.5.4)

Steel reinforcement of thermo mechanically threaded bars of graded Fee-500D for RCC work , where not included in the complete rate of RCC i/c straightening, cutting bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wires etc.complete in all respect above plinth level as per HSR 6.33.6

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material as per (HSR 4.32)

Brick work in 1:3 ( 1cement 3 course sand) mortar with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth complete as derived rate

Suply and Lowering plain and reinforced concrete pipes and specials of 300 mm dia NP-2 into trenches for all depths and laying out the same to correct alignment gradients levels etc., including all dressing and trimming and cutting of concrete beds and joint holes, supporting the pipes and specials in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benching haunches and envelope are completed. The pipes shall rest on the beds at all points throughout their lengths and to ensure this they shall be grouted in where necessary as described in item no.21.38 including carriage from the stores of the Engineer-in-charge and safe delivery thereof at site of works. This includes, loading, unloading, stacking at convenient points adjacent to the works ready for lowering as may be found most convenient in the interest of work.(HSR 20.62.3

Centering and shuttering i/c strutting, proping and removal of form work for roof, landing etc, complete as per HSR 6.30.3

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works above plinth level cement content considered in this item is @ 330 kg/cum up to floor IV level as per HSR item No. 6.25.1

Centering and shuttering i/c strutting, proping and removal of form work for foundation, footing and bases of colomns etc, complete as per HSR 6.29.1

Providing and laying dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks complete as per HSR 10.34

Demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead Complete as per HSR 5.6

Dismantling of brick masonry laid in cement sand mortar manually/by mechanical means i/c stacking serviceable materials and disposal of unserviceable material or as per direction of enginner in charge complete

Providing lowering cutting jointing and testing 900 mm dia RCC pipe class NP 3 as per 18-458-2003 with spigot & socketed joints manufactured with ISi marked sulphate resistance cement as per ISi 12330 with rubber rings ISI marked antiternmite as required at site in to trenches for all depths and laying out the same to correct alignment gradients and levels including dressing and trimming and cutting of concrete beds and side of trenches, if required jointing with rubber rings in trenches and jointing with 1: 3/2 cement sand mortar and with end dowels filled with 1: 3/2. cement sand mortar and finishing the joints at an angle of 45 degree with faces of spigot of socket joints cutting and finishing the cut surface to a uniform finish etc. as fully described in item No . 21.38, item 21.44, item 21.45, & item 21.46 including cartage loading and unloading complete in all respects. The internal diametric of the sewer being: (HSR 21.95.8)

Removing hume pipes-NP 2/NP 3/NP 4 including excavation and taking out the pipes manually/ by mechanical means and stacking the pipes within standard lead as per direction of Engineer-in-charge above 600 mm dia as per HSR item No. 5.53.2

Laying 150 micron polythene sheet (NS)

Supply of 150 micron polythene sheet (NS)

Demolishing cement concrete 1:2:4 or leaner (i/c equalent designmix)manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.complete as per HSR-5.23.2

Credit for Old Brick masonry

Credit for Old 900 mm dia RCC pipe NP-3

credit of old 900 mm dia NP3 (Diversion)

Credit of old tiles

jaipal singh s/o sardara singh