REPAIR/REPLACEMENT OF ROOFING AND CONNECTED WORKS TO CERTAIN MD / OTM ACCN FOR ZONE B UNDER AGE B/R-II AT GE JHANSI

Amount

Dismantling Asbestos Cement (Corrugated or Semicorrugate) sheet in Roof covering complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in unframed works such as roof purlins, rafters, fillets ,ridges etc as in ceiling complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F mild steel (Fe 410 W, Gde E 250, Quality- A) as in roof trusses (framed), trussed, purlins, crane gantries ,rails and fastenings and heavy brackets framing (beams, tee, angle, channels or flat sections) etc complete all as specified and directed .

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including snap grid frame work complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5 mm dia GI wire from roof/Slab/truss including wall/perimeter runner/channel of 15 mm size with and including 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm duly fixed in ceiling frame work complete all as specified and directed.

Providing and fixing 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with Intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of oil bound distemper over a coat of primer suitable for board, all as per manufacturer's pecification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge.

S&F in repairs PVC sandwich wall lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification complete all as specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed.

Supply only liquid Water proofing compound complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S & F stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore pipe complete all as specified and directed.

M&L for non asbestos cement north light curves to suit asbestos cement sheets, fixed with seam bolts and nuts including L-type or J-type or cranked hook bolts etc complete all as specified and directed.

M&L Plain Cement Concrete type B-1 1:2:4 (using 20mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

S&F in repair filleting n exc 25 sqcm in section, in any position and to any shape in cement mortar 1:4 including all mitres, stops, etc complete all as specified and directed.

S&F in repair for 1.00 mm thickness plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

S&F of 3 mm thick sheet figured glass pin headed type, exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. Notes: The rates in inclusive of fixing the glass upto 12.00 m ht with the help of scaffolding or ladder. No separate payment will be done for scaffolding or ladder

Flint India (BID ID -3302966)

VIJAY BUILDERS (BID ID -3307713)

M/S SHIVA TRADERS (BID ID -3303028)

NAVEEN TRADERS (BID ID -3302998)

ADARSH ENTERPRISES (BID ID -3302453)

M/s Jagdish Chandra Arora (BID ID -3302640)

M/S Kumar Contractors (BID ID -3308570)

HARNAM SINGH ANIL SINGH (BID ID -3302946)

M/sDaljeet singh keer (BID ID -3302699)

Dubey Construction Company (BID ID -3308696)

m/s ramesh saran agarwal (BID ID -3302694)

FTH TRADERS (BID ID -3301461)