SPECIAL REPAIRS TO C MESS (COOK HOUSE) BLDG NO. 03,04,05 AND 6A AT NCC OTA KAMPTEE.

Amount

Dismantling of asbestos cement/translucent (corrugated / semi-corrugated etc.,) sheets in roof coverings including ridges complete all as specified and as directed.

Dismantling of wall and ceiling board (fibre, pulp, insulation etc.,) or insulation board, slabs, blankets, any thickness including cover fillets complete all as specified and as directed.

Dismantling of timber scantlings in frame work 40 Sqcm and over in section in any position, unframed work, complete all as specified and as directed

Dismantling of timber scantling as in fillets, rails, posts, rafters, purlins, etc., under 40 Sqcm in section as in unframed/framed work, complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed

Demolition of PCC as in roofs,floors, beams,staircase, landing, chajjas etc., and similar suspendede works and disposal of unserviceable materials, debris and rubbish, complete all as specified and as directed.

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided, complete all as specified and as directed.

M&L for provision of water proofing treatment by using APP torch on mineral/ slate finished membrane over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.3 ltr per Sqm on clean and dry surface and then providing APP membrane having non woven. polyster film reinforcement with 3 mm thick and weight not less than 3.00 kg/Sqm and finished on top with mineral/ slate finished torch on system laid with 100 mm & 150 mm over lap on side & end laps respectively laid over rendering 15 mm thick in CM 1:4, complete all as specified and as directed.

S&F Structural rolled mild steel work as in roof trusses (framed), purlins, crane gantries, rail and fastenings and having buckets framing ( beam, tee, angle, channel or flat section) including distances pieces, cleats etc., including special shaped washer etc. conforming to IS 116-1979 grade Fe-290 (Gde E-165), complete all as specified and as directed.

S&F Pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material & labour Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slab and similar work not exc. 200mm thick (horizontal or sloping) for fair finished flat surfaces of concrete all as specified and as directed.

Use and waste of formwork to edges of concrete flats with fair finished surface, complete all as specified and directed.

M&L for RCC 1 : 1½ : 3 Type A1 (nominal mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L for Non skid colour ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but n.exc. 0.18 Sqm in floors etc set & jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6, complete all as specified and as directed.

M&L for Non skid colour ceramic heavy duty tiles for out door, 10 to 12 mm thick area of each tile not exceeding 0.09 Sqm but not exceeding 0.18 Sqm as in floors, set & jointed in neat cement slurry and pointed in coloured cement to match over and including 20 mm thick screed bed or bedding layer in CM 1:4, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 6-7mm, on vertical surface such as skirting / dado set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tile and including 10mm thick backing coat in CM 1:3 complete all as specified and as directed.

M&L for 4mm thick Non Asbestos, fiber cement building board of size 595 x 595mm size fixed over snap grid framework for false ceiling comprising of the following section for making partition of 600 x 600mm size fixed to wall with rawl plug and screw and hanged to roof with 4mm dia Gl suspended wire of suitable length and butterfly clip of size of main Tee shall be 32mm x 24mm x 0.30mm, cross tee shall be 28mm x 24mm x 0.30mm thick with black lining in mid portion and wall portion and wall angle shall be 24mm x 24mm x 0.30 mm thick complete all as specified and directed.

S & F suspended gypsum false ceiling which includes providing and fixing GI ultra perimeter channels of size 0.55 mm thick having one flange of 20 mm and another flange of 30 mm and a web of 27 mm alongwith perimeter of ceiling, screw fixed to brickwall/ partition with the help of nylon steeves and screws at 610 mm centres, then suspending GI ultra intermediate channels of size 45 mm, 0.9 mm thick with two flanges of 15 mm each from the soffit at 1220 mm centres with ultra ceiling alongwith 25 mm X 10 mm X 0.55 mm thick fixed to soffit with GI cleat and steel expansion fasteners. Ultra ceiling section of 0.55 mm thickness having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm are then fided to the ultra intermediate channel with the help of connecting clips and in direction perpendicular to the ultra intermediate channel at 457 mm centres. 12.5 mm tapered edge gypboard (CVonforming to IS 2095-1982) is then screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. finally the boards are to be jointed and finished so as to have a flush look which includes filling & finishing the tapered and square edges of the boards with jointing compound, paper tape and one coat of primer suitable over wall care putty finish etc., complete all as specified and as directed.

M & L for POP with fibre moulded ceiling cornices, decorative type, design as approved of size n. Exc 200 mm wide fixed with screws complete as per manufacturer's instruction etc., complete all as directed.

M & L for POP with fibre moulded ceiling rounded, decorative type, design as approved of size 1200 mm dia fixed with screws complete as per manufacturer's instruction etc., complete all as directed.

Dismantling of brick work or stone/boulder masonry built in cement mortar including ashlar facing dressed stone and pre-cast concrete articles complete all as specified and as directed

Demolition of un-reinforced cement concrete of any description and in any position and disposal off demolished material and rubbish out of the premises MD land, complete all as specified and as directed

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and as directed

Taking down cement plaster of any description on brick or stone walls including raking out joints hacking for key, scrubbing down with water etc complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

M&L for PCC 1 : 4 : 8 Type D-2 (using 40 mm graded stone aggregate), as in foundations, filling and mass concrete etc., complete all as specified and as directed.

M&L for 75mm thick PCC 1 : 2 : 4 Type B-1 (using 20 mm graded stone aggregate), as in floorings and finished even and smooth with using extra cement, complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement including mist filling in the joints, complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 (Using old size brick) complete all as specified and as directed.

M&L for brick work with fly ash brick, straight or curved on plan to any radius built in half brick thick wall built in CM 1:4 (Using old size brick) complete all as specified and directed.

M&L for Rendering 15 mm thick in CM 1:4 on fair faces of brick masonry or concrete surfaces finished even & smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 15 mm thick in CM 1:6 on fair faces of brick masonry or concrete surfaces finished even & smooth without using extra cement complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20 to 25mm thick, laid over and including 20mm thick cement mortar 1:6 screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc., complete all as specified and as directed.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) as in floors, set, laid over and including 20mm thick screed bed or bedding layer in CM 1:6 jointed and pointed in white cement(1:2) using marble dust with admixture of pigment to match with marble shade, complete all as specified and as directed.

M&L for machine cut Cudappah stone slab flooring 20 to 25mm thick polished one side, laid over and including 15mm thick cement mortar 1:6 screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and as directed.

M&L for machine cut, pre-polished granite stone slab of any shade as approved by GE as in flooring 20 to 25mm thick, laid over and including 20mm thick cement mortar 1:6 screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc if required to be carried out at site after fixing of pre-polished granite stone in position, to match the surface upto required pre-polished standard complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, as in steps, cooking plaforms etc., and similar situations, complete all as specified and as directed.

M & L for 80 mm thick, M-40 grade, machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 laid over, with and including 30mm thick sand dust cushion or bedding layer, with grey cement and pigment complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 by using 20mm graded stone aggregate, as in padding, coping etc., haunching, rounded or chamfered on edges including necessary form work, finished even and smooth without using extra cement, complete all as specified and directed.

Taking down chowkat or frames including shutters (without taking of shutter from the frames) n. exc 1.50 Sqm each, making good disturbed surfaces and removing materials from site, complete all as specified and as directed.

Taking down chowkat or frames including shutters (without taking of shutter from the frames) exc 1.50 Sqm and not exc 4.00 Sqm making good disturbed surfaces and removing materials from site, complete all as specified and as directed.

Taking down shutters of any description not exc 2.00 Sqm each complete all as specified and as directed.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply & fix 30 mm thick 2nd class HW factory made Glazed and Skelton door shutters, open rebated and prepared to receive wire gauge edges cut and mitred beads for securing glass etc., (without sash bars), edges of framing plain, chamfered or rounded, size of members of shutters as specified in SSR Part I section and clause 8.24 (a), kiln seasoned & chemically pressure treated, fitted to Chowkats or frames of any numbers of panels complete all as specified and as directed.

All as per item No 46 above, but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars of any numbers for windows, ventilators etc., as specified in SSR Part I section-08 and clause 8.24 (b), complete all as specified and as directed.

Supply & fix 30mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type of both faces, complete all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube supplying & fixing in opening as per specification & drawing all as specified and as directed.

Supply & fix factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 4mm thick mounded laminated PVC sheet on the front face & 4 mm plain colour PVC sheet on back face, with wood free EPS supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Taking down steel window/ventilator shutter of any size, in any description and in any position and refixing the same after necessary repairs, with and including welding and all accessories as required at site, complete all as specified and as directed.

Supply & fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, as in gauge doors/window/ventilators, as in repairs, complete all as specified and as directed.

Supply & fix 100 mm long Stainless steel medium weight butt hinges and fixed with screw / welded to frames etc., complete all as specified and as directed.

Supply & fix 200 mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and as directed.

Supply & fix 100 mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and as directed.

Supply & fix 150 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and as directed.

Supply & fix 100 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and as directed.

Supply & fix 250 mm long aluminium alloy, anodised, sliding bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and as directed.

S&F sheet glass ordinary quality, 4 mm thick and glazing with oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and as directed.

Taking up or down steel tubing 15mm dia bore and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing 20mm dia bore and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Supply & fix GI tubing 15 mm bore medium grade including all fittings such as bends, elbows, tees, union etc., and fixed to wall/ceiling or laid in floors complete all as specified and as directed.

Supply & fix GI tubing 20 mm bore medium grade including all fittings such as bends, elbows, tees, union etc., and fixed to wall/ceiling or laid in floors complete all as specified and as directed.

Supply & fix 15mm bore Bib tap (half turn), cast copper alloy chromium plated, fancy type, with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and fixed, as in repairs, completed all as specified and as directed.

S&F rotational moulded polyethylene double layered water storage tanks (cylindrical or vertical with closed top) 2000 liter capacity hoisted and fixed in position, all as specified in SSR Part-I, as in repairs, complete all as specified and as directed.

S&F 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum 2 0 m m - 2 1 0 g ms), complete all as specified and as directed.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S&F Solid/ hollow PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, as in repairs, complete all as specified and as directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, as in repairs, complete all as specified and as directed.

S&F 25mm dia Stainless steel curtain rod of approved quality (Make as approved by GE) including cutting and fixing to curtain brackets, as in repairs, complete all as specified and as directed.

S&F fancy type curtain brackets suitable for 25mm dia, of approved quality (Make as approved by GE) fixed to wall with screws, complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M&L for old decorated surfaces of walls of any description by brooming down the surfaces including preparation of surfaces, filling cracks and holes etc., with mixture white cement and fine sand in 1:3, and applying two coat of white wash, complete all as specified and as directed.

All as per item No.73 above, but two coat of white wash on Ceilings

Material & labour for preparation of new plastered surfaces of wall & applying two coats of cement base paint over a coat of primer of approved make complete all as specified and as directed.

Material & labour for preparation of new plastered surfaces of wall & applying two coats of oil emulsion distemper over a coat of primer and putty of approved make complete all as specified and as directed.

Material & labour for complete removal of existing treatment of surfaces of walls & applying two coats of oil emulsion distemper over a coat of primer and putty of approved make complete all as specified and as directed.

Material & labour for complete removal of existing treatment of surfaces of walls & applying two coats of cement base paint over a coat of primer of approved make complete all as specified and as directed.

M&L for complete removal of existing treatment of surfaces of walls & applying two coats of exterior grade acrylic emulsion (Make: ICICI DULUX (VVT)/ASIAN -Apex ultima or equivalent) paint over a coat of primer and Birla white putty of approved make complete all as specified and as directed.

Material & labour for preparation of newly woodensurfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over coat of pink primer complete all as specified and as directed.

Material & labour for preparation of new or previously untreated surfaces of steel or iron works of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over coat of red oxide primer complete all as specified and as directed.

Material & labour for preparation of old wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and as directed.

Material & labour for preparation of old treated surfaces of steel or iron works of any description over 10 cm width or girth & applying one coat of synthetic enamel paint complete all as specified and as directed.

E/M Works:- Taking down unserviceable point wiring with copper/aluminium conductor cable of (light, fan, plug and power plug point) complete including light fittings any type switches, sockets, ceiling rose, switch boards, bell/buzzer, bell push, tube light fittings, regulator etc, and making good disturbed surfaces of walls/floor etc to match with existing surfaces including white/ colour washing/distempering all as specified and as directed.

Taking down carefully unserviceable sub main wiring of any size/capacity and making good disturbed surfaces to match with the existing surfaces complete all as specified and as directed.

Taking down old unserviceable sheet metal enclosure with MCB's ,main switch, etc., and making good the disturbed surfaces of wall all as specified and as directed.

Material and labour for concealed point wiring 1100 volt grade single core PVC FRLSH insulated and unsheathed cable with multi-stranded copper conductor 1.50 Sqmm drawn in with and including electrical grade PVC conduit not less than 20 mm dia with IS 9537 (Part-III) 1983 marking, medium grade concealed on wall/ceiling as per site requirement including PVC FRLSH insulated and unsheathed cable with copper conductor of size 1.50 Sqmm as earth conductor and pressed steel terminal boxes sunk on wall for mounting modular switches, switch sockets. fan regulator, etc including modular cover with frame of any size, including making good the disturbed surfaces complete all as specified and as directed for:- (a) One light point controlled by one No. one way switch.

(b) One Ceiling/Exhaust fan point controlled by one No. one way switch and regulator.

(c) One 3 pin 6 Amps socket out let point on the same board with other switches .

(e) One 3 pin 6 Amps socket out let point on independent board.

All as per item No. 131 here in before, but wiring with 2.5 Sqmm multi stranded copper conductor cable and earth wire with copper conductor cable of size 1.5 Sqmm for 15 Amps power plug point.

M&L for sub main wiring with two single core PVC FRLSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit heavy duty of suitable size concealed in wall of the following sizes :- (a) 2 x 10.0 Sqmm + 1 x 10.0 Sqmm earth wire.

S&F modular switch 1 way 6 Amps 250 Volts AC, 1 Module, Make: Anchor Roma/Legrand/Hager/Crabtree

S&F modular switch 1 way 16 Amps 250 Volts AC, 1 Module, Make: Anchor Roma/Legrand/Hager/Crabtree

S&F modular socket 2/3 pin combined 2 module 6 Amps 250 Volts AC. Make: Anchor Roma/Legrand/Hager/Crabtree

S&F modular socket 2/3 pin combined 2 module 6/16 Amps 250 Volts AC. Make: Anchor Roma/Legrand/Hager/Crabtree

S&F modular ceiling fan regulator step type 120W 2 module. Make: Anchor Roma/Legrand/Hager/Crabtree

Supply & fix ceiling rose ,3 phase /PVC/polycarbonate ,isolated body surface, all as specified and as directed.

Supply & fix LED light fitting 09-12 Watts surface mounted bulk head luminaries complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size of 230V, 50Hz from fitting to ceiling rose complete all as specified and as directed. Make: Philips: Endura LED 10W or Luker: LBKOVSL04 or CG: Cat No. LBH 10 CDL.

S&F LED batten fittings 9-11 Watts, 2' length including drivers having energy consumption, 230 Volts, 50Hz, 6500K, not less than 800 Lunen prewired complete with all accessories, , with and including LED tube rod, connecting up with twin core twisted flexible copper conductor cable of suitable size from fitting to ceiling rose, complete all as specified and as directed. Make:Philips:Smartbright LED 10S or CG: LCTL-9-CDL or Luker: LT509WH.

S&F building security light LED 20/25 Watt with pressure die cast aluminium housing heat resistance toughened glass, IP66 protection, complete with driver with rated voltage 240 V, 50Hz, with and including mounting GI pipe (made out of 25mm dia light grade pipe) 1.2m bent to the required shape fixing with FI clamps nut bolts etc., and connecting up with twin core twisted flexible copper conductor cable of suitable size of 230V, 50Hz from fitting to ceiling rose, complete all as specified and as directed. Make:Philips:BRP 022 LED20CW or CG: LSTS-25-CDL or Bajaj BCLST 20W LED or Luker. LST24WH.

S&F LED tube light fittings 18-22 Watts complete with aluminium body with all accessories, driver with not less than 1800 Lunen O/P and I/P rated voltage 240 Volts, with and including tube rod, connecting up with twin core twisted flexible copper conductor cable of suitable size from fitting to ceiling rose, complete all as specified and as directed. Make:Philips:Smartbright LED 20S or CG: Linea 20W or Surya: SLE BT 20W IP65LXN.

Supply & fix MCB DB Vertical type TPN 4 Way with MCCB 63 Amps, 415 Volts, with 200 Amp rated bus bar flush/surface mounting double door type, complete all as specified and as directed.

Supply & fix MCB DB SPN 8 Way, 415 Volts, with 200 Amp rated bus bar flush/surface mounting double door type, complete all as specified and as directed.

Supply & fix MCB SPN 6 to 32 Amps, breaking capacity 10 KA, 240 Volts, complete all as specified and as directed.

Supply & fix MCB SP 6 to 32 Amps, 240 Volts,, breaking capacity 10 KA all as specified and as directed.

Taking down carefully existing serviceable ceiling fan with down rod complete of 1200/1400 sweep from fan hook, dismentling the blades, cleaning, servicing, painting with two coats of synthetic enamel paint, marking MES No. and refixing the same with twin core twisted flexible copper conductor cable of suitable size from fan to ceiling rose, complete all as specified and as directed.

S&F wall mounted air circulator fan 450mm sweep, single phase, 230 Volts, 50Hz, and connecting up with twin core twisted flexible copper conductor cable of suitable size from fitting to ceiling rose, complete all as specified and as directed. Make: Bajaj/ CG/ Havells / Orient.

S&F Exhaust fan 300mm sweep, single phase, 230 Volts, 50Hz, with nut and bolts, washers etc., and connecting up with twin core twisted flexible copper conductor cable of suitable size from fitting to ceiling rose, complete all as specified and as directed. Make: Bajaj/ CG/ Havells/ / Orient.

M&L for making hole of suitable size for 300mm sweep exhaust fan and including grouting bolts, cutting chasing and plastering, painting etc., to match with the existing surface, complete all as specified and as directed.

Material and Labour for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of earth plate not less than 1.5m below ground level connected to galvanized iron earth lead wire 4.00mm dia by means of bolts, nuts, check nuts, washers of galvanized iron and connected to main switch/control board upto 7.5m away from the earth electrode including excavation earth work, PCC chamber, RCC cover slab char coal, watering pipe, wire mesh lugs, earth lead protection pipe 40mm bore, medium grade 7.5m long as applicable and as per plate No. 3 of SSR Part-I 2009 and all as specified. (a) Excavation and earth work in any type of soil. (b) Drilling of holes in electrode (c) PCC pit in cement concrete (1:2:4) type B-1 (d) 40 mm thick Pre-cast RCC cover or reinforcement with 8mm TMT bars at 100mm c/c both ways with suitable handle. (e) Funnel with watering pipe of GI 20 mm nominal bore ,medium grade & copper lug etc. (f) 15mm nominal bore medium grade GI protection pipe upto 7.50 m long for protection of earthing lead. (g) Requisite quantity of charcoal and common salt. (h) Connection to earthing test point and testing on completion.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.42,374.00 /- ]

chronicle enterprises

M/s Rahul Traders

M/s T.S.JOHAR

Sharma Electrical and Services

Bidder Name

Sharma Electrical and Services

chronicle enterprises

M/s T.S.JOHAR

M/s B S Jain

M/s Rahul Traders