SPECIAL REPAIR TO TECH BUILDING NUMBER T-140 AT MIL STN NABHA UNDER GE (S) PATIALA

Amount

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

Demolition of brick work built in cement mortar.

M&L for brick work in cement mortar (1:4) using sub class 'B' bricks staight or curved on plan exc 6.0 m mean raidus

M & L for 15mm thick ( in two layers of 10mm and 5mm thickness) cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finished complete all as specified and directed Note : Water proofing compound shall be measured and paid saparately under item .

M&L 10mm thick cement plastering in cement mortar CM 1:6 finishing the surface complete all as specified

M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits(thickness vary from1.5to2.5mm as required for desired smoothness and levelling of surfaces in two or more layers)by us ingready made wall careputty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.

Applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

M&L Preparation of new plastered or unplastered surfaces of walls, two coats of cement base paint all as specified.

Supply only integral water proofing compound ISI marked. Make : Pidilite/Sika

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

All as per srl item No 9 hereinbefore but n. exc 1.5 sqm each.

S&F powder coated aluminium glazing/ doors & shutters made out of aluminium anodised section 101.60x44.75x1.75mm for chowkats or frame & shutters made of size 81.25x38.10x1.75mm for side rails, top rails and bottom rails and including 6mm thick glass above and below middle/lock rail, and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including fixing required nos. of pivots/hinges and brass mortice lock (four levers) and two Nos of key complete all as specified and directed.

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

S&F 150mm long alum anodised barrel tower bolts of extended action.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates Powder coated to them (minimum thickness of powder coating 50 microns) bates including joining cleat for fixing glazing/particle board etc. complete all as specified.

S&F 5.5 mm thick sheet glass ordinary quality, glazing and rubber beading with oil putty fixed in aluminium windows/door/partions and all as specified

S & F brass mortice lock of size 100mm long 4 levers.

M& L Door closer Aluminium Die cast hydraulically regulated designation No 3, universal type, suitable type for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixedNo 3 universal type, suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixed all as specified.

Sheet glass ordinary quality 4 mm thick and glazing with oil puttly or wooden beads in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

S & F Wire netting of galvanised steel wire 1.40mm dia and size of mesh 25mm fixed with wooden beds tinned tacks of wire staples

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises

Coloured glazed ceramic tiles (300 x 600 mm) x 7mm or (300 x400 mm)X7mm thick as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed.

M&L for ceramic tiles floor tiles of minimum size 600X600 mm 8 to 10mm thick in flooring etc set and jointed in neat cement slurry and pointed in white cement to match over and including 20mm thick screed bed in CM (1:4) laid over complete all as specified and directed.

Machine cut Kota stone slab flooring 20mm (+2mm) thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 25mm thick cement concrete type B-0 (12.5mm graded aggregate) complete all as specified and directed.

All as per item No 15 here in before on vertical surfaces as in skirting/dado of size as required at site but excluding 25mm thick PCC all as directed.

M&L fo 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed.as in floor base complete all as specified and as directed.

Dismantling of asbestos cement sheets [corrugated, semi-corrugated, etc] in roof coverings complete all as specified

S & F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws as specified

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws as specified.

S&F MS hollow rectangular/square/circular tubes/pipes of Fe410-W(Gde-E-250) Grade as in frame work for roof/rafter/purline/chajja/trusses/columns/struts etc and like similar items etc. complete all as specified.

S&F for plates /cleats/connplates of Fe410-W(Gde-E-250)quality A etc for frame work all as specified.

Dismantling of wrought timber truss scantling 40Sq.cm and over in section framed work, provided for complete as directed .

Dismantling of wrought timber scantling as in fillets, post rafter , purlins etc under 40Sq.cm in section framed work, provided for complete as directed .

Hard core of broken stone boulders of gauge 40 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface all as directed and specified

PCC (1:3:6), 50mm thick as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement

M&L for chequered cement concrete tiles with grey cement and pigment 20cmX 20cmX25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, over 20 mm thick cement screed bedding layer in cem,ent mortar 1:6, All as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring.

S&F Curtain rod Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets

M&L anodised aluminium snap grid false ceiling of grid size 605x605mm consisting of aluminium main and "T' sections of size 25x35x1.5mm thick and wall angles of size 25x 25x 1.5 mm thick suspended with GI wire suspenders of 6mm dia of suitable length and 8-10 mm thick gypsum board, 60x60 cm size fixed with staples on snap grid complete all as specified and directed.

S&F 18 mm thick LEAD FREE PVC celuka ply of both side plain white color fixed with screws, slovent cement/adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufactured's specification complete all as specified and directed. NOTE: not less than 10kg per sqm

S&F 18 mm thick LEAD FREE PVC celuka ply of both side plain of approved color other than white colour fixed with screws, slovent cement/adhesive to make kitchensides top and bottom and shelves inside the cabinets complete as per manufactured's specification complete all as specified and directed. NOTE: not less than 10kg per sqm

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 Kg

S&F Paino/continuous hinge of size 30 mm stainless steel complete all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150 mm long matt finished complete fixed in position all as specified.

Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over and including 15mm thick screeed bed or bedding layer in CM (1:4), in complete all as specified and directed.

Dismantling stone slab and tiles of any description or thickness laid bedded and pointing in any mortar of floor, aprons etc

Dismanteling 500ltr water storage tank and removing to store

Rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position incl 20 mm bore ball brass valves high pressure with polythene float and fly nut all as specified in SSR Part-1.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp, holders brackets, bulk head, mirror light fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring with 1.50 sqmm in copper conductor cable ( multistrand) FRLS single core PVC insulated cable in and including PVC concealed conduit ( ISI Marked) of heavy duly with all accessories ie PVC gutties etc terminated in sunken/pressed metal flush box and white modular cover plate with frame for mounting of switches /sockets/ fan regulators etc and continuous earth wire 1.5 Sqmm copper cable PVC insulated FRLS controlled by one switch for one light/fan/sockets point/ all as specified and directed by Engr-in-Charge in ceiling Portion surface conduit wiring to be done. Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth. (iii) Necessity cutting chasing where ever required shall be part of job & making good the disturbed surfaces shall be part of job.

All as per item No 2 above, but for one 3/5 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 2 above, but for one 3/5 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 2 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

S & F in replacement of modular switch 1 way, 6 Amps, 1 module completeall as specified.

S & F in replacement modular type, Bell push 1 way, 6 Amps, 1 module complete all as specified.Make : Indoasian/Anchor/Havells

S & F in replacement modular type, switch 1 way, 16 Amps, 1 module complete all as specified. Make : Legrand/ Roma/ORIS L&T/Siemens/Wood Make : Legrand/ Roma/ORIS L&T/Siemens/Wood

S & F in replacement modular type, socket 5 pin 6 Amps, 2 module complete all as specified. Make : Legrand/ Roma/ORIS L&T/Siemens

S & F in replacement modular socket 5 pin 6/16 Amps, combination type 2 module complete all as specified. Make : Legrand/ Roma/ORIS L&T/Siemens/Wood

S & F in replacement modular Fan regulator step type, 120 watts, 1 module complete all as specified. Make : Legrand/ Roma/ORIS/Havells

M & L for ceiling rose surface type, 65 mm x 50 mm three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed by the Engineer-in-Charge.

S & F in replacement Vertical load line type VTPN DB, 4 way 415 V, double door as per IS - 8623, IP-54 protection, universal mounting with suitable capacity copper bus bar with nuetral bus bar, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for accomodate MCCB TPN 100 Amp as incomer and TP&SP MCCB/MCBs as outgoing complete & making necessary electrical connection for incoming and outgoing cables, with copper lugs, crimpped with crimping tool complete all as specified and directed. Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing shall be part of job.

S&F in replacement of existing MCCB TPN, 63 Amps, 415 volts, 16 KA complete fixing in DBs including proper thimbles connections all as specified and directed.

S & F in replacement of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 12 way double door type with 200 amp rated bus bar as per IS - 8623, IP-54 protection. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job.

S & F in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, in the MCB DB Complete with connection testing and commissioning complete all as specifed and directed

S & F in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) SPN current carrying capacity 6 to 32 Amp, in the MCB DB Complete with connection testing and commissioning Complete all as specifed and directed

S & F in replacement of FTL with new techonlgy LED having high efficiency of capacity LED 20 Watt, 4 feet long, FIXT ELITE PRIDE PLUS 20 W 6500K, Cool Day Light (CDL) LHEXBLP7PN1W020. Make -Havells. incl necessary electric conection complete all as specified.

S & F in replacement of LED 10 Watt, 2 feet long, Cool day light with NEO Batten10 W 6500K having high efficiency Cat No. LHEXACP7IN1W010. Make -Havells. incl necessary electric conection complete all as specified.

S & F in replacement of recess mounted LED luminaire 28 Watt warm white complete with all accessories incl cost of lamp & driver, suitable for 2x2 feet false ceiling panel complete all as specified and directed by Engineer-in-Charge.

S & F in replacement of lamp holder, PVC/ polycarbonate type with back plate suitable for upto 20 watt bulb for batten fitting, including plastic square board of required size complete all as specified.

S & F in replacement of LED Lamp 12 Watt.

S & F in replacement LED light fitting 1x9W/1X10W bulkhead luminaires 230 Volts including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified by Engr-in-Charge.

S & F in replacemnt new generation energy saving and environmental friendly long life LED building security light 1x25 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with suitable dia light grade GI pipe bend to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed.

M&L for replacement of existing unserviceable earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I

S&F energy saving 3 star rating ceiling fan 1200mm sweep energy efficent as per latest specifications having service value more than 5.5 make: Havells or equivalent in Usha/ Bajaj and suspended from fan hook including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose to ceiling fan.

S&F Metal body Wall mount Fan energy saving 3 star rating 450mm sweep energy efficent as per latest specifications having 230 Volts incl anchoring arrangement all as directed by Engr-in-Charge. Make: Havells, Bajaj or equivalent in Usha/ Bajaj

S & F in replacement of exhaust fan metal body, AC single phase 230/ 240 V of size 300 mm sweep with louver . Note: Fixing of Exhaust Fan on wall with suitable size anchor bolt all as specified and directed.

S & F in replacement 1100 volts grade heavy duty XLPE insulated, armoured heavy duty electric cable with aluminium conductor cross-sectional area 35 sq. mm, 4 core incl grouting into wall , connecting to DB/Panel with suitable size coppr thimbles, making good/mahing the surface of wall complete all as specified.

Excavating in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Material and labour for sand cushioning with dry river sand in trenches for cushioning of underground cable line including spreading, leveling, well ramming completed all as specified and directed.

Supply and laying well burnt sub class ‘B’ bricks. ( designated 75) locally available best quality laid dry in trenches for protection of underground cable all as specified and directed.

Material and labour for replacement of GI tubing light grade 50 mm bore for passing through cables under the floor, along the wall or along the pole complete all as specified and directed.

S & F in replacement of existing unserviceable Plug & Socket Box (sheet metal) with PVC Plug, SPN 16/20 Amps for Acs. Model No. - DHDPHSN020, Make-Havells/Indoasian.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x4 sqmm ( line conductor) & 1x4 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth . (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size . (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x6 sqmm ( line conductor) & 1x6 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth . (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size . (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

Dismantling existing ceiling fan with hanging pipe, refixing the same with new hanging GI pipe of suitable size below false ceiling duly painted all as directed by Engr-in-Charge. Note :- Cost of Pipe is included the rate of the item.

M&LSupply of waterless and maintenance free Earthing (grounding) electrode of overall size 100mm dia, 3000mm depth, 25mm in dia with copper bonded, ETP Grade MS conductor,(254 micron, UL Listed ) Conductive aggregate mixed with cement to embed or backfill the voide surrounding the 25mm Coppeer bonded MS conductor placed at the centre of a augured bore hole of 150mm dia & 3150mm depth. The surface area of the earth electrode shall lower the earth resistance permanently without periodic watering or recharge of earth enhancing compound for a period of 30 years in all type of soil conditions and shall not leach into the soil or Under-ground water channels, Electrod's top terminal shall be sealed permanently & earth strip shall be taken cut and terminated to earth bus bar, the earth electrode shall be able to withstand the fault current up to 40KA for 1 second complete as per specification and requirements. with polyethlene FRP Pit Box (Extra Heavy Duty). Note :- (i) Cost of earth work, PCC & Brick masonary work for earthing pit, RCC pit Cover, cutting work done by cutter & testing etc. all shall be deemed to included in unit rate. (ii) Test report in duplicate on satisfied value shall be submitted by contractor to this office. Make :- JMV LPS limited / JEF / Alcoice conducrete.

NARINDER KUMAR SONS