GE/ALP (8628) KOLKATA OF 2026-27

Dismantling removing all unsound concrete, plastered material by chipping/chiseling gently at all effected and adjoining areas of concrete etc till sound surface is reached various locations in building; subsequently cleaning the surfaces by hair brush and air blower and removing rubbish off the premises including hoisting assembling and fixing of double layer steel scaffolding to external perimeter of building complete all as specified and directed. Note: Work shall be carried out to bldgs upto height of 8 storey.

Removing of concrete all around reinforcement bar upto 12 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiseling etc) and M&L for applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area thoroughly by water and allow it to dry and totally rust free of reinforcement bar complete all as specified and directed. Make: ( Rust removing chemical ):- Reebaklens RR of FOSROC or equivalents solutions SIKA/STP or equivalent as approved by GE Note: Work shall be carried out to bldgs upto height of 8 storey.

Preparation of existing reinforcement surface by brush and M&L for application of two component epoxy zincrich primer on existing reinforcement surface of minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre. complete all as specified and directed. Make- Nitozinc primer of FOSROC or equivalent as approved by GE. Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for introducing new reinforcement TMT bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc complete all as specified and directed. Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for supply, mixing and placement of micro-concrete cement based prepacked single component chloride free, sulphate free, non-shrink, free flow. elf compacting, ready to use after mixing water in specified proportion (Make:- Sika Rep Microconcrete-4 or renderoc-RG of Fosroc equivalent as approved by GE) in required thickness as per manufacture's instruction and all as directed. Compressive strength (ASTN C 109,cm cube) of 35 MPa at 28 days including application curing compound concrete WB manufactured by Fosroc of equivalent at various locations in Bldgs including necessary form work complete all as specified and directed. Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for providing and applying two component structural grade polymer modified reinforcement mortar (Make:- Fosroc Renderoc S2 or equivalent as approved by GE) upto a thickness of 30 mm over a coat of epoxy resin bonding agent Nitobond EP. The cured mortar shall achieve a minimum compressive strength of 12N/mm2 in a day & 45 N/mm2 in 28 days with Flexural strength 8N/mm2 in 28 days Chloride diffusion coefficient shall be Nil after 24 hours when tested by Accelerated electrochemical chloride ion diffusion test method and the depth of carbonation shall be Nil after 24 hours when tested by Accelerated carbonation test. in addition to this percentage of water absorption should be 0.45 after 24 hours in immersion test at various locations in Bldgs complete all as Specified and directed. Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction complete all as specified and directed. Make:- Concure LP90 of FOSROC or equivalents solutions SIKA/STP/ Maruti / Choksey chemicals or equivalent as approved by GE Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for applying a flexible expansion joint membrane of minimum 150mm wide and 1mm thick, expoband one of FOSROC or equivalent as approved by GE over the prepared joint using a two part epoxy adhesive nitobond PC 40 of Fosroc or equivalent. The minimum tensile strength of the membrane should be more than 12 N/mm2 and elongation at break should be more than 400%. The installation of the membrane should be carried out complete all as specifiied and as directed. Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for inserting mild steel shear key bars/levelling gauges of required length and diameter in reinforced/plain concrete for drilling suitable holes in RCC Slab/ wall/ column/ beams to a depth as directed for anchoring steel reinforcement bars including washing with water inserting lokfix 'E' of Fosroc or equivalent in the holes at various location in Bldgs complete all as specifiied and as directed. Note: Work shall be carried out to bldgs upto height of 8 storey.

M&L for applying Anti carbonation coating as per manufacturer's specification of approved brand, manually using brushes on the hardened concrete/plastered surfaces after cleaning the surface and removing all loose particles, deposits etc complete including one coat of primer and two coats coatings complete all as specifiied and as directed. Note: Note: Work shall be carried out to bldgs upto height of 8 storey.

Hacking out old broken glass any thickness, size quality or description from wooden/steel frame fixed with wooden beads/metal pinning complete all as specified and directed

S&F in repairs 4 mm thick Figured glass in square not exc. 0.50 sqm in each pane, fixed with pin headed beads or putty (in metal frames etc) complete all as specified and directed.

S&F in repairs 5.5 mm thick plain sheet glass and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F in repairs stainless steel wire cloth with stainless steel 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with wire staples (for windows and gauzed doors) complete all as specifiied and as directed.

S&F in repairs stainless steel bow handle fabricated type 125mm long complete all as specifiied and as directed.

S&F in repairs 100 mm long stainless steel butt hinges, medium weight, cold rolled and fixed complete all as specifiied and as directed.

S&F in repairs 200mm long stainless steel barrel tower bolts of extruded section and fixed complete all as specifiied and as directed.

S&F in repairs stainless steel curtain rod anodised aluminium alloy 25 mm dia with pair of suitable brackets,finnels and also making good the wall surface to match the existing surfaces complete all as specified and directed.

S&F in repairs 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specifiied and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and directed.

S&F suspended false ceiling (Decorative Type) system using metalic (E grid) exposed suspende system, grid section size 600mm x 600mm comprising of GI powder coated main runner of dimension 32 mm x 24mm x 0.80mm thick ( thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of Runner) Cross Tee of dimensions 26mm X 24mm x 0.8 mm thick, wall angle 22.00mm x22.00mm x 0.35 mm thick ( thickness comprising of GI/0.35 + PPPCGS/0.3 mm) with and including 4 mm thick HPSC ( High pressure steam cured) pre- primed, self embossed textured designer board, water resistant termite resistant, fire resistant for insulation and accustic purpose to be placed in the grid system duly suspended with 4 mm dia G I bars hangers fixed with steel dash through fasteners with Provn of light fixture complete all as specifiied and as directed.

S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and incl Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long ccomplete all as specifiied and as directed.

S&F Gypsum Board 12mm thick in ceiling flat or slopping fixed in jointless finish with jointing compound and jointing tape fixed with screw as per manufacturers instructions with provn of light/electric fixtures complete all as directed complete all as specified and directed.

Preparing of new gypsum board ceiling, pillasters, cornices etc and M&L for applying one coat of 3 mm thick wall care putty with & including two coat acrylic distemper complete all as specified and as directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) incl PVC seat cover, (excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain (or outgoing pipe) and to flushing pipe etc. complete all as specifiied and as directed.

S&F in repairs PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approved by GE complete all as specified & directed.

S&F in repairs white Plastic water closet seat cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device complete all as specifiied and as directed.

S&F in repairs CP tubular towel rail 600mm long 20 mm dai complete all as specified and directed.

S&F in reapirs 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs 110/125 mm floor trap fixed in floor with grating incl jointing with solvent 1:2:4 cement concrete, complete all as specifiied and as directed.

S&F in repairs Vitreous china squatting pan of orissa patern size (580 x 440mm) white with integral foot rest (excluding flushing cistern and flush pipe) complete all as specifiied and as directed.

S&F in repairs Urinal spreader of CP any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified & directed.

S&F in repairs half stall Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specifiied and as directed.

S&F in repairs 15 mm Dia CP Bib taps (Two-in-one), fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specifiied and as directed.

S&F in repairs Health Faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and wall hook including making connections and fixed in position complete all as specifiied and as directed.

S&F in repairs 15 mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm-125gms) complete all as specified & directed.

S&F in repairs 15 mm dia bib tap cast copper alloy chromium plated with capstan head handle, screwed down high pressure screwed for iron pipe or for brass ferrule complete all as specified & directed.

Supply only white cement in bags of 25 Kgs packing complete all as specified and directed.

S&F in repairs 15mm dia, fancy type, pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specifiied and as directed.

S&F in repairs 15 mm dia pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-110gms) complete all as specified & directed.

S&F in repairs 15 mm dia stop valve cast copper alloy chromium plated with capstan head handle, screwed down high pressure screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F in repairs 15mm dia angle valve, chromium plated, screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe on for unions, complete all as specified and directed.

S&F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specifiied and as directed.

S&F PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specifiied and as directed.

S&F in repairs Brass CP mixer for mixing hot & cold water (for wash hand basin) and fixed including dismantling of 15mm dia chromium plated pillar tap, complete all as specified and directed.

S&F in repairs 15 mm dia wall mixer cost copper alloy chromium plated with capstan head handle, screwed down high pressure screwed for iron pipe or for brass ferrule complete all as specifiied and as directed.

S&F in repairs 110 mm bore PVC (SWR) Pipes single socket, complete all as specified and directed.

All as per BOQ Serial item No 48 above but 75mm bore complete all as specifiied and as directed.

S&F in repairs PVC bend/tee suitable for 110mm bore pipe complete all as specifiied and as directed.

All as per BOQ Serial item No 50 above but 75mm bore complete all as specifiied and as directed.

S&F in repairs door closer hydraulically regulated (extruded section) , designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 complete all as specified and directed.

S&F in repairs door closer hydraulically regulated (extruded section) , designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 61 to 80 complete all as specified and directed.

S&F in repairs heavy duty double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel complete all as specified and directed.

S&F in repairs 19mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortor bedding (but not backing removing serviceable to store complete all as specified and directed.

M&L for glazed ceramic (coloured) tiles of size 450x300 6-7mm thick as in vertical surface/dado set and jointed with approved adesive and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Anti-skid joint free ceramic (coloured) tiles 7-8mm thick area of each tiles exeeding 0.06 sqm but n.exceeding 0.11 sqm in toilet/bath floor etc.set and jointed with approved adesive and pointed in epoxy grout with spacers complete all as specified & as directed.

M&L for Non Skid joint free ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specifiied and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc laid, bedded & pointed in any mortar complete all as specifiied and as directed.

M&L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specifiied and as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, indow-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specifiied and as directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specifiied and as directed.

M&L for bedding layer of mortar 10 mm thick in CM 1:3 for laying wall/dado finishes complete all as specifiied and as directed.

S&F in replacement rotational moulded polythylene water storage tanks 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position with & including 20 mm brass valve high pressure with polythene float and fly nut complete and GI tank nipple, screwd for iron pipe complete all as specified and directed.

All as per BOQ Serial item No 66 above but 1000 ltr capacity complete all as specifiied and as directed.

All as per BOQ Serial item No 66 above but 2000 ltr capacity complete all as specifiied and as directed.

Taking down wooden/steel chowkhats/door/window frame including shutter (without taking off shutter) exc.1.5 Sqm but n exc 4 sq m each area complete all as specifiied and as directed.

Taking down wooden/steel chowkhats/doo/window frame including shutter (without taking off shutter) area not exc.1.5 Sqm each complete all as specifiied and as directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium ections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specifiied and as directed.

S&F Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators or aluminium frame for partition works etc with one or more rebates including joining cleat for fixing etc. complete all as specifiied and as directed.

S&F Anodised powder coated aluminum Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specifiedr and including dismantling of existing unserviceable Aluminium window complete all as specifiied and as directed.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868) of approved design/pattern, with approved standerd section and fix to the existing window frame with C.P brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specifiied and as directed. (only weight of grill to be measured for payment)

S&F 12 mm thick prelaminated particle boards (ISI marked), interior grade prelaminated both side with decorative choice lamination, fixed with necessary clips and other like to aluminium frame work, as in doors, windows, partition etc complete all as specified and as directed.

M&L for Cub-boards shutters made with Prelaminated Particle board 18/19 mm thickness, interior grade prelaminated both side with decorative choice lamination, fixed with screws to timber frame work complete all as specifiied and as directed.

S&F Glass film reflective type sticked to glass panes as per manufacturers intructions complete all as specified & directed.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, angle iron chowkhats; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. .

Taking down wooden/steel chowkhats/door frame including shutter (without taking off shutter) area exc.4 Sqm each complete all as spd & directed.

S&F 1.25 mm thick lath Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer and two coat of synthetic enamel paint ;erected in position as indicated, complete:but gear operated type with bevel gear box and crank handle complete all as specified and directed.

S&F in repairs safety lever locks mild steel with 4 levers for rolling shutters complete all as specifiied and as directed.

S&F in repairs Ball bearing including suitable springs for rolling shutters complete all as specifiied and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking up or down 15mm bore steel water tubing and connections, complete all as specified and as directed.

Taking up or down 20mm bore steel water tubing and connections, complete all as specified and as directed.

Taking up or down 25mm bore steel water tubing and connections, complete all as specified and as directed.

S&F in repairs CPVC pipes 16 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings as in walls, ceiling, floor, etc. complete all as specified and directed.

S&L in repairs 20 mm bore (Outer dia) CPVC pipes of SDR 11 and plain CPVC SDR 11 fitting fixed on wall or floor (concealed ), ceiling or laying in floors complete all as specifiied and as directed.

S&L in repairs 25 mm bore (Outer dia) CPVC pipes of SDR 13.5 and plain CPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as specifiied and as directed.

S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specifiied and as directed.

S&F 25 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specifiied and as directed.

S&F 20mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specifiied and as directed.

S&F 25mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specifiied and as directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs 32 mm PVC waste pipe 900 mm long with complete all as specifiied and as directed.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specifiied and as directed.

S&F in repair vitreous China wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with flyash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for brick work with flyash old size bricks, straight or curved on plan to any radius in half brick thick walling built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removal of debris outside MoD land complete all as specified and as directed.

M&L for 5mm thick plastering on ceiling surfaces in CM (1:3) surface finished even and fair complete all as specified and directed.

M&L for 20mm thick (in two layer) plastering on fair face of Brick surface with CM (1:4) mixed with WPC finish surface even and smooth with out using extra cement complete all as specified and directed.

M&L for 15mm thick cement plaster with CM (1:6) on other than fare face of brick wall finsh even and smooth without using extra cement complete all as specified and directed.

Disposal of building rubbish/malba/similar unserviceable, dismantled or waste materials by mechanical means, including loading, tranporting, unloading to approved municipal dumping ground outside MoD land as directed complete all as specified and directed.

Complete removal of existing treatment by using electric sander machine or steel wire brushing to remove all dust and loose scale etc of wall surfaces & prepare to receive wall care putty complete all as specified & directed.

M&L for 1mm thick wall care putty on wall including rubbing with sand paper to achieve a smooth surface & sharp straight edges etc. complete all as specified and directed.

Preparation of old decorated walls & M&L for applying two coats of acrylic oil emulsion distemper complete all as specified and directed.

Preparation of decorated Ceiling and M&L for applying two coats of acrylic oil emulsion distemper complete all as specified and directed.

Preparation of newly plastered wall surface and M&L for applying two coats of oil bound distemper over & including a coat of primer on complete all as specified and directed.

M&L for two coat of Anti fungal anti bacteria paint on old decorated surface of internal walls inclding removal of existing preparation and 3mm wall care putty as per manufacturers instructions & complete all as specifiied and as directed.

All as per BOQ Serial item No 113 above but as in ceiling surface complete all as specified and as directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over 2mm thick wall care putty and icluding priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

Preparing of new steel surfaces and M&L for applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and as directed.

M&L for applying two Coats of Synthetic Enamel Paint over & including one coat of primer to steel and iron surfaces of any description, not otherwise described including preparation of new or previously untreated surface complete all as specified and directed.

M&L for one coats of synthetic enamel paint, area exc.10cm width or girth over old painted wooden surfaces including preparation of surface complete all as specifiied and as directed.

M&L for one coat of plastic emulsion paint on old decorated surface of internal walls incl preparation complete all as specifiied and as directed.

Supply only Intregal water proofing compound complete all as specifiied and as directed.

M&L for L-shaped rubberised corner guard for sharp vertical edges of length 1000mm, width 100 x 100mm reflective type of thickness 10mm complete all as specified & as directed.

Dismantling of interlocking tile 60-80mm thick complete all as specified and directed.

Supply and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and incl 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Supplying and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and as directed.

Demolition of cement concrete above ground floor n.exe 15cm thickness(below or above ground level) complete all as specifiied and as directed.

M&L for PCC type D-2 (1:4:8) (using 40mm graded stone aggregates) as in fundations, filling and mass concrete complete all as specified and directed.

M&L for 50 mm thick Cement concrete type C- 2, 1:3:6 (40mm graded stone aggregates) as in sub base floor, hard standing and like complete all as specifiied and as directed.

Please Enable Macros to View BoQ information