NIT No. 1112/TC/EinC/PWD/25-26

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 meters including removal and disposal of top organic soil not exceeding 150 mm in thickness if required and as per relevant clauses of section-200. In area of light jungle

Compacting Original Ground Compacting Original Ground supporting embankment Loosening, leveling and compacting original ground to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at O.M.C. and then compacted by rolling so as to achieve minimum dry density as given in table 300-2 for embankment construction.

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, ,carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 (A) Plant mix method (with Mechanically crushed stone only)(b) For Sub-base cum drainage layer or upper sub-base with (i) Grading-V Material

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406.)

Prime coat (Providing and applying primer coat with oil based bitumen emulsion (SS-1, grade confirming to IS:8887) on prepared surface of granular Base including clearing of road surface and spraying primer using mechanical means as per clause 502. (i) on WBM/WMM surface @0.85 Kg/sqm.

Tack coat Providing and applying tack coat with bitumen emulsion (RS-1, grade confirming to IS:8887) using emulsion pressure distributor on the prepared Bituminous /granular surface cleaned with mechanical broom and as per clause 503. (ii) Granular surfaces treated with primes @ 0.30 kg /Sqm

Bituminous Macadam (Providing and laying bituminous macadam as per clause 504 with mixed prepared in minimum 40-60 TPH capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction) (B) With mechanical paver finisher (ii) for Grading-II(19 mm nominal maximum size, bitumen content 3.40%)

Close Graded Premix Surfacing/Mixed Seal Surfacing (Mechanical means using minimum 40-60 TPH capacity of HMP. Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness using bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade, complete as per clause 508) (II) With mechanical paver finisher (A) With bitumen (ii) Type B ( 13.2 mm to 0.09 mm size aggregates )

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe on first class bedding. (Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe for culverts on first class bedding of granular material including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets). (A) 600 mm dia

Providing and laying cement concrete for plain concrete/ reinforced concrete i/c form work, shuttering complete in as per drawings and specifications.( For Village roads) (i) M - 10

Providing & Laying un reinforcement cement Concrete without dowel bar including formwork and expansion construction and longitudionla joints as per design and IRC 62-2014 over a prepared base as per approverd mix design and finishing line and grade as per drawing for pavement thickness less than 200 mm in low volume roads. (iv) PCC Grade M - 30 Minimum cement Content @ 375 Kg/Cum

Providing and laying cement concrete for plain concrete/ reinforced concrete i/c form work, shuttering complete in as per drawings and specifications.( For Village roads) (ii) M - 15

Retro reflectorized Traffic signs (Providing and fixing of retro reflectorized cautionary ,mandatory and informatory sign as per IRC : 67-2012 made of retro reflective type sheeting vide clause 801.3, fixed over aluminium sheeting of required thickness supported on a mild steel back frame of ISA 40x 40x5 mm and mild steel angle post 75mm x75mm x6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x45 cm x60 cm ,60 cm below ground level as per approved drawing and painting all components of the signs and supported as per clause 7.2 of IRC 67-2012 Made of Class A High intensitysuper engineering grade sheeting of Type II (for village road) With aluminium sheeting of 1.5 mm thickness (i) 900 mm Equilateral Triangle

Retro reflectorized Traffic signs (Providing and fixing of retro reflectorized cautionary ,mandatory and informatory sign as per IRC : 67-2012 made of retro reflective type sheeting vide clause 801.3, fixed over aluminium sheeting of required thickness supported on a mild steel back frame of ISA 40x 40x5 mm and mild steel angle post 75mm x75mm x6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x45 cm x60 cm ,60 cm below ground level as per approved drawing and painting all components of the signs and supported as per clause 7.2 of IRC 67-2012 Made of Class A High intensitysuper engineering grade sheeting of Type II (for village road) With aluminium sheeting of 1.5 mm thickness (iv) 800 mm x 600 mm rectangular

Retro reflectorized Traffic signs (Providing and fixing of retro reflectorized cautionary ,mandatory and informatory sign as per IRC : 67-2012 made of retro reflective type sheeting vide clause 801.3, fixed over aluminium sheeting of required thickness supported on a mild steel back frame of ISA 40x 40x5 mm and mild steel angle post 75mm x75mm x6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x45 cm x60 cm ,60 cm below ground level as per approved drawing and painting all components of the signs and supported as per clause 7.2 of IRC 67-2012 Made of Class A High intensitysuper engineering grade sheeting of Type II (for village road) With aluminium sheeting of 1.5 mm thickness (vi) 600 mm x 600 mm square

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro reflectorized sign as per IRC:67-2012 made of Micro prismatic grade type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm,60cm below ground level as per approved drawing) Made of Class B High intensity micro Prismatic grade sheeting of Type IV (for Village road)

Kilo Meter Stone (Reinforced cement concrete M15grade kilometer stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) (ii) Ordinary Kilometer stone (Precast)

Kilo Meter Stone (Reinforced cement concrete M15grade kilometer stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) (iii) Hectometer stone (Precast)

Providing & Fixing Hazard Marker Type-2 Partial Retro Reflective Size 0.30 x 0.90M made of 16 gauge (1.6 mm) thick mild steel sheet Confirming to IS:2062 Painted with one cast of Zinc Chromate Stoving Primer and two coats of Black Stove Enamel (Oven Baked) paint with 10 cm bands of yellow Retro- Reflective Sheeting of Engineering Grade pasted a per IRC:79 including one MS angle Iron post of size 50x50x5 mm of 1.65 meter long duly painted with synthetic enameled paint block including bolts and fixing the same in M-15 concrete black of size 30x30x30cm, including transportation etc. Complete.

Excavation for drain (Earth work in excavation for drain/chamber as per drawing and technical specification, including setting out,construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.)

Plain cement concrete complete as per drawing and Technical Specifications (i) PCC M - 15

Construction of RCC drain /chamber cover, placing in position, providing shuttering and concreting by using concrete mixer, compaction by vibration etc complete as per drawings and technical specifications excluding reinforcement. with RCC M-20

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in drain/cover/chamber complete as per Drawing and Technical Specifications.

Cutting of trees, including cutting of trunks, branches and removal of stumps, roots,stacking ofserviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression /pit and as per relevant clauses of section-200 for :- (i) Girth from 300 mm to 600 mm

Cutting of trees, including cutting of trunks, branches and removal of stumps, roots,stacking ofserviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression /pit and as per relevant clauses of section-200 for :- (ii) Girth beyond 600 mm to 900 mm

Cutting of trees, including cutting of trunks, branches and removal of stumps, roots,stacking ofserviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression /pit and as per relevant clauses of section-200 for :- (iii) Girth beyond 900 mm to 1800 mm

Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter,dressing of sides and bottom and backfilling with approved material including dewatering etc. complete. (I) Ordinary soil (i) up to 3.0m depth

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe. (Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe for culverts including fixing collar with cement mortar 1:2 but excluding bedding below pipes, excavation, protection works, backfilling, concrete and masonry works in head walls and parapets . (D) 1000 mm dia

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification 710.1.4 of I.R.C. 78 and 2200. (i) Granular material

Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material including dewatering etc. complete. (I) Ordinary soil (i) Upto 3 m depth

Sand Filling in Foundation Trenches as per Drawing & Technical Specifications. (A) Using concrete mixer

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications. (A) Using concrete mixer (i) PCC Grade M15

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications. (A) Using concrete mixer (ii) PCC Grade M15

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 (Newly laid concrete shall be covered by gunny bags). (A) Height upto 5m (a) Using concrete Mixer (ii) PCC Grade M20

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 (Newly laid concrete shall be covered by gunny bags). (D) Height upto 5m (a) Using concrete Mixer (i) RCC Grade M20

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification sections 1500, 1600 and 1700 (Newly laid concrete shall be covered by gunny bags). (B) RCC Grade M30 (I) For Solid Slab Super Structure (a) Using Concrete Mixer (i) Height upto 5m

Filler joint (B) Providing & fixing 20 mm thick compressible fiber board (12 m long x 25 cm deep ) in expansion joint complete as per drawing & Technical Specification.

meter

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, ,carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 (A) Plant mix method (with Mechanically crushed stone only)(b) For Sub-base cum drainage layer or upper sub-base with (ii) Grading-VI Material

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit