Construction of Matak Bhawan at Banipur, Dibrugarh, Assam

Amount

1) GROUND FLOOR AREA = 784.77SQM.+36.74SQM. (TOILET BLOCK) AND D.G. SHED AREA = 56.27 SQM. Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2.6.1 All kinds of soil

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 11.1.1, 1:4 (1 cement : 4 coarse sand)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cemt : 4 coarse sand)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) Main Building (G.F.balance work),

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (cement : sand) Main Building (G.F.balance work),

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from..sources) Main Building (G.F.balance work),

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.3 Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Main Building (G.F.balance work),

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

CEMENT PLASTER (In coarse sand), 12 mm cement plaster of mix : 13.4.1, 1:4 (1 cement: 4 coarse sand) Main Building (G.F.balance work),

12 mm cement plaster finished with a floating coat of neat cement of mix : 13.7.2, 1:4 (1 cement: 4 fine sand)

CEMENT PLASTER (In coarse sand), 15 mm cement plaster on rough side of single or half brick wall of mix: 13.5.1, 1:4 (1 cement: 4 coarse sand) Main Building (G.F.balance work),

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs …. separately). 9.1.3 Hollock wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 9.5.2 Kiln seasoned and chemically treated hollock wood 9.5.2.1, 35 mm thick shutters

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws conforming to IS 1328 BWR Type

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc.complete as per architectural drawings and directions of engineer..... 21.2.1 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, ..filling up the ....., i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc........ (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . .... in basic item): 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 9.74.2, 200x10 mm, Door,

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 9.74.3, 150x10 mm, Window

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 9.75.2, 250x16x5 mm, Door,

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Door

Providing and fixing bright finished brass handles with screws etc. complete: 9.81.2, 100 mm, Door,

Providing and fixing bright finished brass handles with screws etc. complete: 9.81.3, 75 mm, Window

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Door

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Main Building (G.F.balance work),

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Main Building (G.F.balance work),

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Main Building (G.F.balance work),

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces Main Building/ DG (G.F.balance work),

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat ... butt hinges and screws and applying a priming coat of ..... as per the direction of Engineer-In-charge. Main Building/ DG (G.F.balance work),

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufac-turers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm.

13.48.2 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @0.75 ltr/10sqm of approved brand and manufacture

13.48.3 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture Main Building/ DG (G.F.balance work),

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) ...as nuts, bolts, fasteners etc.).

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc.....

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, ....shade, laid on 20 mm thick cement mortar 1:4 ..easily. 11.41A.3 Glazed Vitrified tiles Matt/..size 11.41A.3.2 Size of Tile 600 x 1200 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm .... specified and as directed by the Engineer-in-Charge. 11.56.2 Polished Granite stone slab of all colour and texture except …. Stairs and steps

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size...excluding the cost of painting with : 12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer's specification, with all …... than 0.60.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone agg. 20 mm nomi. size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and ...grouted with fine sand, including necessary excavtion, levelling & dressing & finishing the top smooth.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cemt : 4 coarse sand) Plinth Protection Drain

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 11.1.1, 1:4 (1 cement : 4 coarse sand) Plinth Protection Drain soling

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) Plinth Protection Drain

12 mm cement plaster finished with a floating coat of neat cement of mix : 13.7.2, 1:4 (1 cement: 4 fine sand) Plinth Protection Drain

2) FIRST FLOOR AREA = 821.51SQM. Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Main Building (F.Floor),

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.3 Suspended floors, roofs, landings, balconies and access platform Main Building (F.Floor),

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Main Building (F.Floor),

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Main Building (F.Floor),

5.9.7 Stairs, (excluding landings) except spiral-staircases Main Building (F.Floor),

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Main Building (F.Floor),

SANITARY INSTALATIONS & WATER SUPPLY WORKS: Providing and fixing white viterous china pedestal type water closet ( European type WC pan) with seat and lid, 10 litre low level white P.V.C. Flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1, W.C. Pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm or 340 x 410 x 265 mm sizes respectively.

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing and fixing kitchen sink including making all connections excluding cost of fittings.Providing and fixing kitchen sink including making all connections excluding cost of fittings. 17.26.1 White glazed fire clay sink of size 600x450x250 mm

Providing and fixing wash basin with CI brackets, 15mm PTMT pillar cock, 32mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls werever required. White viterous china flat back wash basin size 550x400 mm with single 15mm PTMT pillar cock.

Providing and fixing mirror of superior glass ...and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : 17.32.2, Rectangular shape 453x357mm

Providing and fixing soil, waste and vent pipes : 100 mm dia, Sand cast iron S&S pipe as per IS: 1729. 17.65.1, 100 mm dia. pipe, 2x3.05+30.62= 36.72

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 17.65.1, 100 mm dia. pipe,

Providing and fixing plain bend of required degree. 17.39.1.1, 100mm, Sand cast iron S &S pipe as per IS: 1729

Providing and fixing double equal plain junction of required degree. 17.42.1.1, 100x100x100x100mm, Sand cast iron S &S pipe as per IS: 1729

Providing and fixing collar. 17.57.1.1, 100mm, Sand cast iron S &S pipe as per IS: 1729

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. 1 x 5 = 5

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe, 17.28.2.1, 32 mm dia,

Providing and fixing toilet paper holder : 7.34.1, C.P. brass,

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of stadard shape with bracket ... Soap container,

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with minimum distances of 37mm from wall face with cocealed fittings.. Soap container,

WATER SUPPLY WORKS :: Providing and fixing Chlorinated Polyvinyl chloride (CPVC) pipes, having thermal stability for hot and cold water supply including CPVC plain & brass threaded fittings. This includes jointing of pipes..testing..Engineer in Charge. 18.9.1,15mm nomi. dia.pipes,

18.9.3, 25mm nomi. dia.,

18.9.4, 32mm nomi. dia.,

18.9.5, 40mm nomi. dia.,

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc., Internal work - Exposed on wall 18.10.1 15 mm dia nominal bore,

18.10.4 32 mm dia nominal bore,

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 ....complete as per standard design : 18.34.1 With common burnt clay F.P.S. (non modular) bricks of class 1 x 3 = designation 7.5

Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10.....complete as per standard design : 18.36.1 With common burnt clay F.P.S. (non modular) bricks of class 1 x 1 = designation 7.5

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 18.49.1, 15mm nominal bore,

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 18.51.1, 15mm nominal bore,

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 18.52.1, 15mm nominal bore,

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and laying S&S C.I. Standard specials such as tees, bends, collars tapers and caps etc, suitable for flanged jointing as per IS : 1538 : 18.66.1 Up to 300 mm dia,

Providing and fixing gun metal gate valve with CI wheel of approved quality : 18.17.3, 40mm nominal bore,

Providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 18.18.3, 25mm nominal bore,

Providing and fixing uplasticised PVC connection pipe with brass unions: 18.21.2, 45 cm length 18.21.2.2, 20mm nominal bore,

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 18.31.1, 100 mm diameter, 18.31.1.1, Class I,

Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested : 18.42.3, Beyond 12 m and up to 18 m depth

Providing and placing in position filters of 40 mm diameter G.I. pipe with brass strainer of approved quality.

Providing and fixing to filter and lowering to proper levels 40 mm G.I. pipe for tube well including cleaning and priming the tube well.

Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 18.46.5, 40 mm nominal bore,

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without ..base support... Water storage tank,

Electrical Works: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. 1.10.1: Group A

Group B

Group C

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 1.14.1: 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1.27.3: 4 Module (125mmx75mm)

12 Module (200mm X 150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1.28.3: 4 Module

12 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.10.1: Single Pole

Double pole

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 16 KA, TPMCCB

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying, installing, testing and commissioning of following capacity TPN distribution tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with HRC fuses, interconnections, earthing etc. as required. 32 amps TPN, 6 way

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm

Supplying of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].Aero King Havells 5 STAR model 1200 mm Sweep

Supplying fitting & fixing of Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver. 20 W Havells ( Rate as per Price list enclosed )

Supplying fitting & fixing of Recessed low depth Aluminium Heat Sink Downlighter made with EASH technology in round and square. PC difffuser in white powder coated finish with integral electronic low THD(<10%) LED driver. INTEGRANEOSURFACEDLS12WLED830S

Supplying fitting & fixing of 12 W LED bulb CROMPTON DYNARAY in the existing lamp holder as specified and directed by the department .

Supplying of following AC Exhaust fan Metallic of following sweeps as approved by the Deptt.as required complete and as directed by the Department [Without regulator].Ventil Air DB NEO/DB 300mm Sweep

Supplying one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size (cable rate as per RR cable price list) 2C Aluminium 10 sq mm armoured cable

Supplying one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size (cable rate as per RR cable price list 2023) 3.5 C 70 sqmm Aluminium armoured

Supplying and installation of V4 Submersible Pump set 2 HP 1.5 KW in existing borewell of appropriate size.

Supplying with installation testing and commissioning of Hi-Wall 3 star rating non ducted split type air conditioner with cordless remote complete with coipper pipe and electrical connection cable, as approved by the dept. upto 5m between the indoor and outdoor unit as directed by the dept. 1.5 ton

Item: Supplying and fixing of die-cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting. JETAALBAFLOODLIGHT60W

Supplying, installation testing and commissioning of the following rating copper wound indoor / out door type transformer complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 100 KVA star rating up to 4 star, above 100KVA as per CEA guidelines for losses along with LV enclosure. 11/0.4 KV 63 KVA Aluminium wound transformer.

Load Security to be paid to APDCL

Supply ,installation testing and commissioning of 57 KVA 3 phase Diesel Generator set Kirloskar Make Model No.4R810ETA 4G1 CPCB IV Silent with STD Panel and Shed

Supply and installation of 100 A On load Changeover Switch including all connections, testing and commissioning

SRI BISHNU CHETRY (BID ID -291204)