Customized Furniture and Kitchen equipment for CBI office

Customized Furniture and Kitchen equipment for CBI office

Wooden Single Bed

Metal Single bed

Wooden Double Bed

Double Mattress

Single Mattress

Single Mattress with Memory Foam

Blanket with pillow cover

Back Cabinet Unit of size 5500MM X450MM X 3000MM

Back Cabinet Unit of size 4000MM X 450MMX 3000MM

Back Cabinet Unit of size 3500MM X450MM X 3000MM

Wooden Wardrobe of size 1800MM X 900MMX450 MM

Mid Back Revolving chair

10 seater conference table

20 seater conference table

50 seater conference table

Auditorium table

Reception Table

Wardrobe of size 2100mm H x 1800mm W x 450mm D

Aduitorium chair

High back revolving chair

High back revolving chair natural leather

Cafeteria chair

High back executive chair

Visitor chair Powder coated

Visitor chair Chrome finish

Working Storage

Storage Unit of size 4500W X 450D X 1800HT

Working table of size 1500 mml x 600 mm d x 750 mmh

Personal Locker Unit

Single Seater Sofa

Single seater Recliner

Cafeteria Table

Cubicle workstation with side composite pedestal

Working Cabin table with side composite storage and 1.2 meters height L shaped partition.

Executive Table 3.6 Meter

Executive Table 2.4 Meter

Modular Office Table 1.8 Meter

Single Burner Unit

Two Burner Unit

Working Table with sink

Tilting rice Boiler

DOSA Chapatti plate

Chapati rolling table

Chapati collecting trolley

Three burner chinese cooking unit

Tandoor Unit SS Gas

Chapati Rolling table

Worktop refidgerator

4 door vertical Refridgerator

2 Door Vertical Refridgerator

MS Fabricated Rack

Atta maida Bins

SS 3 sink washing unit

SS Pot rack 4 shelf

Clean dish and glass rack 4 shelf

SS Bain marie with 10 vessel

SS Soiled dish collection Trolley 3 Tier

Water cooler 80 Ltrs

SS paltform trolley

L.P.Gas PIPELINE MANIFOLD SYSTEM

L.P.Gas pipeline

MS Fabricated Cylinder room

HOT AIR VENTILATION SYSTEM

External Signage made of SS 304

12mm WPC Letter

Wooden planter 1.5Ft Single Bed: Supplying

placing in position and functional working Solid wood ( Beech wood or Seasham Wood or equivalant ) customized Single Size Bed(1070x2030)

Finished in clear lacquar. Height 350- 400mm. Headboard Height 670mm. All three sides having smooth curved edges with solid wood & tapered legs. Moisture resistant 12mm thick pre laminated premium plywood mattress board. Premium polish with low chemical emission. 10mm high buffers offer ground clearance for easy cleaning. The cot should be polish with min 6 layer of polishing to achive premimum velvet finish. The polish should have the low chemical emission to ensures healthy indoor air quality. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Factory-made Customized Metal Bed with metal planks as approved by Engineer-in-charge having following specification. TOP PLANK – Top plank shall be made by 1 mm thick CRCA sheet conferming the IS IS 513: 2008 . UNDERSTRUCTURE-Metal Understructure - Headboard & Tailboard of 50X25X1.2 mm THK MS conforms to IS 4923 Bid Details 2/110 and Top frame of combination of 50X25X1.2mm THK Rectangular pipe & 25X25X1.2 mm THK square pipe. The frame finished with powder coat up to 50-60 Micron.Construction : Flat Pack. SIZE: 2085 (L) x 956 (W) x 650/450 (H) mm upto headboard Finish- The bodies including shelves should be given anti-rust surface treatment & are powder coated with epoxy polyester powder. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of 50 to 60 (+\- 5) microns. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Double Bed: Supplying

placing in position and functional working Solid wood ( Beech wood or Seasham Wood or equivalant) customized double Size Bed (2090x2000x950)

Finished in clear lacquar. Height 350-400mm. Headboard Height 950mm. All three sides having smooth curved edges with solid wood & tapered legs. Moisture resistant 12mm thick pre laminated premium plywood mattress board. Premium polish with low chemical emission. 10mm high buffers offer ground clearance for easy cleaning. The cot should be polish with min 6 layer of polishing to achive premimum velvet finish. The polish should have the low chemical emission to ensures healthy indoor air quality. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Double Bed Mattress size (W) 1830mm X (D) 1980mm X (H) 150mm

This dual sided mattress has premium memory foam layers for a better back support & should have non-allergenic

anti- microbial properties. The fabric used in it is tear resistant yet breathable and has foam quilting. 3 Layers construction with soft -touch high GSM fabric . Mattress size should be as per supplied bed size.The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Single Bed Mattress size (W) 912MM X (D) 1980mm X (H) 100mm

This dual sided mattress has premium memory foam layers for a better back support & should have non-allergenic

anti-microbial properties. The fabric used in it is tear resistant yet breathable and has foam quilting. 3 Layers construction with soft -touch high GSM fabric .Mattress size should be as per supplied bed size. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Single Bed Mattress size (W) 912MM X (D) 1980mm X (H) 150mm

This dual sided mattress has premium memory foam layers for a better back support & should have non-allergenic

anti-microbial properties. The fabric used in it is tear resistant yet breathable and has foam quilting. 3 Layers construction with soft -touch high GSM fabric .Mattress size should be as per supplied bed size. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Classic Memory Foam Pillow size 5(W) 610mm X (D) 406mm X (H) 100mm . Open cell structure that reacts to body heat and weight by moulding to the sleeper’s body

Organic Cotton Fabric for extra comfort

Anti-fungal & Anti-allergic. The finish

design & size of the pillow is tentative and could vary +_ 5% and to be approved by engineer in charge.

300TC Duvet Cover Double Bed Premium Cotton Stripes -Quilt/Comforter Bid Details 3/110 Cover- 90x100 Inches

Razai Blanket Cover for Double Bed (White) with pillow cover. The finish

design & size of the quilt is above and could vary +_ 5% and to be approved by engineer in charge.

300TC Duvet Cover Single Bed Premium Cotton Stripes -Quilt/Comforter Cover- SINGLE SIZE 135 x 200 cm

Razai Blanket Cover for Single Bed (White) The finish

design & size of the quilt is above and could vary +_ 5% and to be approved by engineer in charge.

BEDSIDE UNIT: Supplying

placing in position and functional working bed side table.Overall Size : 400mmW x 450mmDX500H. Material : Body and drawer panels of Bed side table are made of 18 mm thick MDF As per IS 12406:2021

BIS certification Board with 1mm thick laminated

all the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Side panels are made of 18 mm thick MDF As per IS 12406:2021

BIS certification board with imported H.D.F. foil wrapped decorative trim fixed on to it. Hardware : The high quality hardware (with 5 years warrenty ) soft touch/hydraulic used like Roller slides

dowels is of make approved make. 18 mm thick MDF As per IS 12406:2021

BIS certification Board is in shade matching to bed. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

BACK CABINET UNIT: Size : Supplying

placing in position and functional working Customized as per approved drawing and design by client ( 5500MM X450MM X 3000MM) Supplying Fitting and Fixing Back Cabinet with composite storage made out of 19 mm thick bwr ply. All external surfaces and internal surface finished with 3 mm Veneer with lacquar polish

necessary Hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

BACK CABINET UNIT: Size : Supplying

placing in position and functional working Customized as per approved drawing and design by client ( 4000MM X 450MMX 3000MM) Supplying Fitting and Fixing Back Cabinet with composite storage made out of 19 mm thick bwr ply. All external surfaces and internal surface finished with 3 mm Veneer with lacquar polish

necessary Hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

BACK CABINET UNIT: Size : Supplying

placing in position and functional working Customized as per approved drawing and design by client ( 5500MM X450MM X 3000MM) Supplying Fitting and Fixing Back Cabinet with composite storage made out of 19 mm thick bwr ply. All external surfaces and internal surface finished with 3 mm Veneer with lacquar polish

necessary Hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

BACK CABINET UNIT: Size : Supplying

placing in position and functional working Customized as per approved drawing and design by client ( 4000MM X 450MMX 3000MM) Supplying Fitting and Fixing Back Cabinet with composite storage made out of 19 mm thick bwr ply. All external surfaces and internal surface finished with 3 mm Veneer with lacquar polish

necessary Hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

BACK CABINET UNIT: Size : Supplying

Bid Details 4/110 fixing

placing in position and functional working Customized as per approved drawing and design by client ( 3500MM X450MM X 3000MM) Supplying Fitting and Fixing Back Cabinet with composite storage made out of 19 mm thick bwr ply. All external surfaces and internal surface finished with 3 mm Veneer with lacquar polish

necessary Hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Wordrobe Size :Supplying

placing in position and functional working ( 1800MM X 900MMX450 MM) Supplying Fitting and Fixing Back Cabinet with composite storage made out of 19mm BWR Ply placed horizontally & vertically and 6 mm back side with all external surfaces will be pested with 1.2 mm laminate and internal surface pested with 0.8 mm thick balancing laminate with necessary Hardware (with 5 years warranty ) soft touch/hydraulic and hanger rod in ss 304 grade crome finish . The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Med back mesh chair colour with matte finish specification : Type : MB 360 360°degre revolving chair

All over size : 680mm(l)x575mm(d)x 1035mm(h)

Details : Arms : two way adjustable pu padded arms with up & down position. Use of ply: 15 mm thick hot pressed bwr plywood grade 303 for seat. Seat: 40 ±2 mm thick polyurethane foam with density 45 ( (±3) kg per cu meter for best quality cushioning in seat

Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support mesh design based on symmetrical lumbar support mechanism : synchro multi locking mechanism . Gas lift 100 mm telescopic haudraulic . Base : 650mm nylonbase with smooth castors . The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

"CONFERENCE TABLE: Supplying

placing in position and functional working unitzed 10 seater Conference Table.Work Surface: Made MDF As per IS 12406:2021

BIS certification/Plywood of finished thickness of 36 mm

one side prelaminate board conforming to IS14587: 1998 and having chamfered edge. Full length access panel is provided with soft closing hinges in line with worktop edge. Understructure: The understructure consists of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990

Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty: Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS- 12823:1990

Edge banded with matching 2 mm thick PVC lipping. Wire Management: An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513

epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cutout for 4 module is provided for electrical fittings in Straight two seater and single seater modules below access flap per seat.Overall dimension in mm (2100x1150x740) (WxDxH). The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"CONFERENCE TABLE: Supplying

placing in position and functional working unitzed 10 seater Conference Table.Work Surface: Made one side prelaminate board conforming to IS14587: 1998 and having chamfered edge. Full length access panel is Bid Details 5/110 provided with soft closing hinges in line with worktop edge.Understructure: The understructure consists of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS- 12823:1990

Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty: Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990

Edge banded with matching 2 mm thick PVC lipping. Wire Management: An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513

epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cutout for 4 module is provided for electrical fittings in Straight two seater and single seater modules below access flap per seat.Overall dimension in mm (3000x1150x740) (WxDxH). The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"CONFERENCE TABLE: Supplying

placing in position and functional working of a 20-Seater Modular Conference Table. Worktop: The tabletop will be constructed from 25mm thick pre-laminated MDF As per IS 12406:2021

BIS certification

finished with 1.2mm laminate in an approved shade.The edges will be banded with 2mm thick PVC lipping.A soft-closing dual-access flap will be integrated into the design

allowing for convenient access to power supply and data cables.Understructure: The understructure will comprise a combination of 25mm and 18mm pre-laminated MDF As per IS 12406:2021

BIS certification

also finished with 1.2mm laminate in an approved shade. The edges will be banded with matching 2mm thick PVC lipping for a cohesive look.An anodized aluminum alloy 63400-WP profile. will be added at the bottom edges . Wire Management: A wire raiser constructed from 0.8mm CRCA MS (IS:513) will be included to facilitate organized routing of wires and cables. The wire raiser will be epoxy polyester powder-coated with a DFT of 40-60 microns for durability.A power box with two cutouts on either side will accommodate a standard 8-module setup.Additional cutouts with plates will be provided next to each cutout for mounting audio-visual cables (e.g.

etc.). Module Dimensions: Overall Size will be 5075 (w) x 2400(d) x 750(ht) 2-Seater Module: 1350mm (W) x 600mm (D) x 740mm (H) :- 4 nos. Head Module: 2400mm (W) x 850mm (D) x 740mm (H) :- 2 nos. 1-Seater Module: 675mm (W) x 600mm (D) x 740mm (H) :- 2 nos. The finish

and sizes of the furniture are tentative and may vary by ±5%

subject to approval by the engineer in charge.. "

"CONFERENCE TABLE: Supplying fitting & fixing conference table 50 seater 1. Dimensions: 13755mm (L) x 2795mm (B) x 750mm (H) 2. Construction:Tabletop: The tabletop will be made from 36mm thick pre-laminated MDF As per IS 12406:2021

BIS certification (Medium Density Fiberboard)

The surface will be finished with a 1.2mm thick laminate in an approved shade.Side Panels: The conference tabletop will be supported by 25mm thick side panels made of MDF As per IS 12406:2021

BIS certification

finished in a brown-black oak color with a 1.2mm thick laminate in an approved shade.Modesty Panel: Below the tabletop

an 18mm thick pre-laminated MDF As per IS 12406:2021

BIS certification modesty panel will be installed

ensuring a clean and polished appearance.Edge Treatment: All exposed edges of the work surface will be finished with 2mm thick edge binding tape in a matching color

secured with hot Bid Details 6/110 melt glue for a seamless finish. 3. Wire Management: The table will feature a 6-module flip-top box (without switch- socket) mounted above the tabletop. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"CONFERENCE TABLE: MEETING TABLE 1. Dimensions: 1650mm (L) x 900mm (D) x 750mm (H) 2. Construction: Tabletop: The tabletop will be constructed from 25mm thick MDF As per IS 12406:2021

BIS certification (Medium Density Fiberboard) board

finished with a 1.2mm thick laminate in an approved shade. Gable End & Modesty Panel: The gable end and modesty panel will be made from 18mm thick MDF As per IS 12406:2021

BIS certification board

also finished with a 1mm laminate extending to the ground level. Edge Treatment: All exposed edges of the tabletop will be treated with machine-pressed 2mm thick imported PVC lipping

glued with hot melt EVA glue that is free from any VOC (Volatile Organic Compounds)

ensuring a healthier indoor environment. 3. Wire Management: The table will feature a 450mm anodized flip-up wire management solution

made from aluminum with an anodized finish. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

"DRESSING TABLE : Supplying

placing in position and functional working Dresser. Overall Size :Width : 90cm

Height : 201.3cm. Material: Body panels are made of 18 mm thick MDF As per IS 12406:2021

BIS certification Board all external surfaces will be pested with 1.2 mm laminate and internal surface pested with 0.8 mm thick balancing laminate. All the exposed edges are edge banded with 2 mm thick PVC edge banding.Mirror (6mm thick ) Door & Drower fronts are made of 18 mm thick is made of MDF As per IS 12406:2021

BIS certification board. Body back is made of 18 mm thick MDF As per IS 12406:2021

BIS certification board. Hardware: (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

LUGGAGE RACK :Supplying

placing in position and functional working Providing

fitting and fixing of luggage rack

made of 19mm thick plywood IS 710 grade BWP . All inside surfaces to be finished with 0.8mm thick laminate and outer visible surfaces to be finished with 1.0 mm thick laminate with necessary Hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. Size-750Lx500Wx750H

"RECEPTION TABLE : Customized as per approved drawing and design by clien Supplying and Placing in Position of modern design reception desk MDF As per IS 12406:2021

BIS certification board all external surfaces will be pested with 1.2 mm laminate and internal surface pested with 0.8 mm thick balancing laminate.colour : Asian Maple or as per approval of EIC. finish : Main table size : 2400 mm(l)x 900 mm(d)x 750

1050 mm(h). Over all size is 2400 mm(l)x 900 mm(d)x 750 mm(h)

table top made of 25mm thick also table top based on side panel's made 18mm thick MDF As per IS 12406:2021

BIS certification board . Combination construction of reception desk above table top 18 mm thick counter top to table top height is @ 300mm

overall reception desk height is @ 1050mm with toughened glass (8mm) counter top

table top made 25 mm thick MDF As per IS 12406:2021

BIS certification board work surface with the exposed edges shall be finished with 2mm thick pvc edge Bid Details 7/110 binding tape of matching colour and shade fixed with hot melt glue. Along with 18mm thk additional modesty panel size is 1050 mm (l) x 700 mm (h) .1 mobile pedestal (2 drawers + 1 filing cabinet )size is 400 mm(l)x 450 mm(d)x 725 mm(h) in provided with central lock's for security and handle's are provided for easy of opening & pedestal's move on nylon castors. Ms powder coated cpu trolley with castors. Pvc keyboard tray. Three layer MDF As per IS 12406:2021

BIS certification board . Finish of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. colour shall be finalised by the client/Engineer in charge . The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

"STUDY TABLE : Supplying

placing in position and functional working of workdesk . Overall dimensions: (W)90*(D)60*(H)71.3 Material All panels are made of 18 mm thick MDF As per IS 12406:2021

BIS certification Board pested with 1mm laminate. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Hardware : (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. wooden dowels. Finish 18 mm thick MDF As per IS 12406:2021

BIS certification Board . Drawer Size ( 30 cm x 40 cm x15cm) The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. "

placing in position and functional working Material: Body panels are made of 18 mm thick MDF As per IS 12406:2021

BIS certification Board all external surfaces will be pested with 1.2 mm laminate and internal surface pested with 0.8 mm thick balancing laminate. All the exposed edges are edge banded with 2 mm thick PVC edge for Entertainment Floating Tv Unit For Living Room | Floating Media Tv Cabinet | Open Shelf & 2 Door Drawer Storage (1200x300x250mm)

Hardware : (with 5 years warranty ) soft touch/hydraulic. The finish

design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working kennedy wardrobe for guest room material : MDF As per IS 12406:2021

BIS certification board

Wardrobe size : 2100mm (H) x 1800mm (W) x 450mm (D). Colour : walnut finish with laminate finish . Providing & suppling placing position of modular wardrobe top shall be made from 25 mm thick MDF As per IS 12406:2021

BIS certification board pested with 1 mm thick laminate internal surface pested with 0.8 mm thick balancing laminate. While rest of the sides as well as shelves and shutter to be made up of 18 mm thick MDF As per IS 12406:2021

BIS certification board. machine pressed exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade fixed duly pasted with the assistance of edge banding machine at 200 degree celsius. Wardrobe with 2 shutters construction is 2 openable doors with 2 fixed shelve

form ground to lock height is @ 1000 mm & cloth hanger rod holder in stainless steel

in wardrobe provided with 1 universal cam lock for security and handles are provided for easy of opening . over all height of product is @ 2100 mm . Each shutter should be fixed with required numbers hinges

ss tower bolt of 100 x 10

double strip magnetic catcher and drawers shall have 100 mm size ss fancy handles (one on each drawer) with necessary hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the Bid Details 8/110 furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

placing in position and functional working Auto tip up - Auditorium Chair Specification : Standard Heavy Duty Auditorium chairs ( Fix type with tip up ) Structural Frame: Back Rest frame : Mild Steel of size 25 X 3 mm flat bend as per ergonomic contour “ S “ bend to suit the body shape. Seat frame : Mild Steel of size 20 X 4 mm flat “ C “ bend type with cross flat running across the frame. Note : In main load bearing structure no Wood based frame is require. WING COMPONENTS : HRCA/CRCA Sheet Metal/IS: 1079-1994 Type C/U of 1.6/2 mm sheets. Legs frame ‘ U ‘ Type shaped. Side wing frame made up of 80 x 40 mm rectangular pipe of 2.0 mm thick with side is covered with 6 mm wooden ply with fabric upholstery. SPRINGS : For tip up mechanism Coil Spring/Spring Steel IS : 4454 1981 GRADE 2 Tested for 1

000 Cycles. Spacing: The spacing from back to back shall be from 1000 mm. The distance from seat to back of the front row should be 262 mm. " "Arm rest: The armrest should be in wooden PU polish without cup holder. As an optional you can get Skinned Integral PU armrest also without cup holder. Support: The chair shall rest on the ground on two side panel frames (Side Panel/Aisle Panel ). Stand will be in tubular steel structure. Metal tube IS : 4923-1997- 80 X 40 mm

1.63/2.0 mm Thickness. M.S. sheet metal frame formed in 1.6/2.0 mm . The side wooden panel must be 6 mm thick with fabric upholster with a spacing of 560 mm ctc. Grouting: The side panels will be fixed to the floor using 2 nos Grouting bolt - M 8 X 75 mm expandable anchor fasteners with chemicals for grouting. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working modern/mb : Med back mesh chair Type : Med back 360°degre revolving chair : mb

All over size is : 680mm(l)x575mm(d)x 1035mm(h)

with head rest. Details : Arms : two way adjustable pu padded arms with up & down position. Use of ply: 12 mm minimum hot pressed bwr plywood (is grade 303 for seat). Seat: 40 ±2 mm thick polyurethane foam with density 45 ( (±3) kg per cu meter for best quality cushioning in seat

Back : frame of design shall be curved made of two pieces injectionmoulded frame cover with mesh. backrest support mesh design based on symmetrical lumbar support mechanism : synchro multi locking mechanism . Gas lift 100 mm telescopic haudraulic . Base : 650mm nylon/Chrome base with smooth castors . The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working high back 360° degre revolving chair

All over size is : 610mm(l)x 500mm(d)x 1300mm(h)

the chair made of full natural leather . Details :- Arms : chrome finish arms with pu padding . Use of ply: 12 mm minimum thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat . Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : multi-locking knee tilt mechanism . Only seat size is 510mm(L) x 610mm(H) & the back size is 640mm(L) x 530mm(H). Seat maximum height is 610mm & minimum height is 530mm & back height from floor maximum height is 1130mm & Bid Details 9/110 minimum height is 1040mm. Gas lift 80mm telescopic haudraulic ; Base : 650 mm chrome plated and assembled with injection moulded black polypropylene hub cap with smooth castors . The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working stackable modern design cafeteria chair coco material : synthetic fiber size : 381mm(l)x 419mm(d)x 839mm(h). Cafeteria chair size is 381mm(l)x 419mm(d)x 839mm(h) a combination of synthetic fiber with stainless steel make the products utile and a delight

the complete structure shall be made up of 20% glass filled blow molded high density polyethylene

the frame structure shall be supported by ( 2 straight + 2 slant ) four legs.the tubular welded frame is made from dia2.22 + 0.03cmx 0.12+/0.0128 cm and 3.5+/0.03 cm x 0.12+ 0.0128 am stainless steel 202 grade tube & the tube are buff polished.seat and in back given handle to hold are made of injection moulded high impact strength polypropylene polymer compound with indoor grade uv resistance and pressed fitted with legs. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working high back natural leather chair in brown colour with matte finish specification : - office seating - - berlin chair

Type : High back 360° degre revolving chair

All over size is : 673mm(l)x 508mm(d)x 1270mm(h)

The chair made of full natural leather. Details : Arms : wooden arms with leather padding arm rest are fitted to the seat & back. Use of ply: 12 mm minimum thick hot pressed bwr plywood (is grade - 303 for seat and back). Seat: 40 ± 2 mm thick polyurethane foam with density 45 (±3) kg per cu meter for best quality cushioning in seat . Back : 40 ± 2 mm thick polyurethane foam with density 45 (±3) kg per cu meter for best quality cushioning in back .backrest support foam design based on symmetrical lumbar support. Mechanism : multi-locking knee tilt mechanism . Seat maximum height is 580mm & minimum height is 500mm & back height from floor maximum height is 1270mm & minimum height is 1219mm

Gas lift 80mm telescopic haudraulic

Base : the prong (base) is made of soild wood with polished and fitted with 5 numbers. twin wheel castors (castor wheel dia. 50mm) & 700mm pitch center dia (740mm with castors). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working visitor chair. 1. SEAT ASSEMBLY: The seat assembly is made up of 1.2 ±0.1cm. thick hot-pressed plywood

upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) 2. BACK ASSEMBLY: The back asembly is made of Base : chrome finish tublar frame of cantilever type . The back is upholstered using Net fabric with high tenacity yarn. 3. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =45+/-2 kg/m³ and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 4. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. 6. TUBULAR FRAME (FOR 7512RG): The powder coated (DFT 40-60 microns) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. WIDTH (W): 61.0 CM. DEPTH (D): 64.5 CM. HEIGHT (H): 93.5 см. SEAT HEIGHT (SH): 46.5 CM. The finish

design & Bid Details 10/110 size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working fix cantilever chair

All over size is : 610mm(L)x 505mm(D)x 990mm(H)

The chair made of full leatherette in black colour. Details : - Arms : chrome finish arms with pu padding . Use of ply: 12 mm minimum thick hot pressed BWR plywood (IS Grade - 303 for seat and back) .Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat

Back : 40 ± 2 mm thick polyurethane foam with density 45 (±3) kg per cu meter for best quality cushioning in back . backrest support foam

sign based on symmetrical lumbar support backrest support . Only seat size is 610mm(L)x 505mm(D)x 485mm(H) & the back size is 610mm(L)x 540mm(H)

Base : chrome finish tublar frame of cantilever type . The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. "

placing in position and functional working clint/c back unit storage material :18mmMDF As per IS 12406:2021

BIS certification board pested with 1.2mm thick laminate

Back unit size : 1600 mm (l)x 450 mm (d)x 800 mm (h). Providing & suppling placing position of modular back unit top shall be made from 18 mm thick MDF As per IS 12406:2021

BIS certification board. While rest of the sides as well as shelves and shutter to be made up of 18 mm MDF As per IS 12406:2021

BIS certification board. machine pressed exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade fixed duly pasted with the assistance of edge banding machine at 200 degree celsius and nternal surface pested with 0.8 mm thick balancing laminate.. Storage unit with 4 shutters construction is 1 openable door with 1 fixed shelve + 2 openable door with 1 fixed shelve + 1 openable door with 1 fixed shelve

in provided with 3 universal cam lock for security and handles are provided for easy of opening. over all height of product is @ 800 mm . Each shutter should be fixed with required numbers hinges

ss tower bolt of 100 x 10

double strip magnetic catcher and drawers shall have 100 mm size ss fancy handles (one on each drawer) with necessary hardware (with 5 years warranty ) soft touch/hydraulic. for installation of side unit wooden dowels and minifix to use for additional support. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Storage SIZE - 900 X 450 X 1200 HT Specification: The storage top will be made of 25mm thick BWR grade ply

shutter & sides panel are made of 18mm thick & back panle is made of18mm thick BWR ply of approved shade . all exposed serface pested with 1.2mm thick laminate and un-exposed surface pested with 0.8mm thick laminate.. All the edges of storage surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from lowVOC.with finger groove handle & suitable lock.All exposed area PVC edge lipping with necessary hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

"Supplying and Placing in Potition of Center Table size (W)1150mm X (D)487mm X (H)458mm.the unit made of beech wood with one nos self. The top glass will be made of 8mm thick tougen glass.. Premium Polish: The table should be polished with a Bid Details 11/110

minimum of six layers to achieve a premium velvet finish. Low Chemical Emission: The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Mobile Pedestal SIZE: 4500W X 450D X 1800HT Pedestal are made of 18mm thick MDF As per IS 12406:2021

BIS certification board of approved shade.back panle is made of18mm thick MDF As per IS 12406:2021

BIS certification ply of approved shade . all exposed serface pested with 1.2mm thick laminate and un-exposed surface pested with 0.8mm thick laminate.. All the edges of storage surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from lowVOC.with finger groove handle & suitable lock.All exposed area PVC edge lipping with necessary hardware (with 5 years warranty ) soft touch/hydraulic The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working table 18mm MDF As per IS 12406:2021

BIS certification pedted with 1.2mm thick laminate size : 1500 mm(l)x 600 mm(d)x 750 mm(h). finish : laminated. a combination of metal and wood make with storage side unit structure of over all size is 1500 mm(l)x 600 mm(d)x 750 mm(h) Side Storage Will be Opeanable Shutter

table top made of 25mm thick MDF As per IS 12406:2021

BIS certification pested with 1.2mm thick laminate. On table top 6 module flip top box without switch & shocket single raceway & pole with powder coated below wiring & table top supported with non toxic ms powder coated ""c"" shape metal legs verticle of size 50mm x 50mm x 1.6 mm and connectors horizontal of size 40mm x 40mm x 1.6 mm ms pipe. providing 0.8mm thk ms powder coated to the thickness 50-60 microns(+/-5 micron) crca sheet perforated modesty panel at front side

below top with work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue.all metal parts should finishing with epoxy polyester powder coated to the thickness 50-60 microns(+/-5 micron) with necessary hardware (with 5 years warranty ) soft touch/hydraulic. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working vault 4 door personal lockers material : mild steel size : 380mm(l)x 450mm(d)x 1855mm(h).finish : epoxy polyester

Construction : rigid knockdown. material shall be crca 0.6 mm thickness . construction shall be rigid knockdown construction

shelf shall be uniformly distributed load capacity per each shelf level is 30 kg maximum.these components shall be made of crca ‘d’ grade high yield strength as per is:513 & is:304 grade. Features: index holder & air ventilation hole

concealed metal hinges w/o exposed brackets (better security). Finish shall be epoxy polyester powder coated to the thickness of 50 microns . handle/label holder shall be appealing snap fit abs plastic handle . ventilation shall be attractive punched pattern for ventilation.the finishing shall include epoxy powder coated to the thickness of 50 microns (+/10). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Casper Side Table size (W)577mm X (D)393mm X (H)460mm. the unit made of beech wood . The Bid Details 12/110 top glass will be made of 8mm thick tougen glass.. Premium Polish: The table should be polished with a minimum of six layers to achieve a premium velvet finish. Low Chemical Emission: design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working 1 seater sofa size : 1140mm(l) x960mm(d)x 820mm(h). Material : premium leatherette style : 3 seater exclusive premium leatherette lounge seating sofa with kiln-dried wood framing makes it warp and scratch resistant

comfortable seat depth & height designed wrapped in buttery-soft premium leatherette with panelled back and cushioned armrests. Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12MM grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried german beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue

the frame shall be padded with high resilience polyurethane foam having 24 +/- 5 density in seat it shall be stack foam of 50mm thik

32mm thick back foam having 45 +/- 5 density foam used

there shall be cushion arm 25mm thick provided padded with high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered with premium leatherette

it complements the modish legs are made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h)

arms height @ 685mm back height @ 460mm ). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Leatherette 1 Seater Sofa size :- (W) 1090mm X (D) 965mm X (H) 940mm. Seating Height 480mm. Arm height 712MM. Seat Depth 570mm. Back Height 430mm. Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 15 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried german beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue

the frame shall be padded with high resilience polyurethane foam having 24 +/- 5 density in seat it shall be stack foam of 50mm thik

32mm thick back foam having 45 +/- 5 density foam used

there shall be cushion arm 25mm thick provided padded with high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered with premium leatherette

it complements the modish legs are made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h)

arms height @ 685mm back height @ 460mm ). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Leatherette 1 Seater Manual Recliner in Brown:Premium Leather Dimension (W) 820mm X (D) 940mm X (H) 1050mm Frame Material Solid Wood Upholstery Material Nappa Aire Leather Filling Material: Foam (Standard Density: 45 +/- 5 kg/m³) Seat Material Nappa Aire Leather Finish Matte Dimension (W)820mm X (D)940mm X (H)1050mm Number Of Recliners 1 Number Of Reclining Positions 3 Mechanism Power Seating Bid Details 13/110 Capacity 1 Seater Seating Height 490mm Function Autolift The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working 2 SEATER Size will be 1460 x 960x820. Material : premium leatherette/style : with kiln- dried wood framing makes it warp and scratch resistant

the panelled back and cushioned armrests Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried beech wood. the complete structure shall be covered by p.u.foam fixed with adhesive glue

the frame shall be padded with high resilience polyurethane foam having 45 +/- 5 density in seat it shall be stack foam of 50mm thik

32mm thick back foam having 45 +/- 5 density foam used

there shall be cushion arm 25mm thick provided padded with high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered it complements the modish legs are made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h)

arms height @ 685mm back height @ 460mm ). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working 3 seater size : 2125mm(l) x960mm(d)x 820mm(h). Material : premium leatherette style : with kiln-dried wood framing makes it warp and scratch resistant

the panelled back and cushioned armrests Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried beech wood. the complete structure shall be covered by p.u.foam fixed with adhesive glue

the frame shall be padded with high resilience polyurethane foam having 45 +/- 5 density in seat it shall be stack foam of 50mm thik

32mm thick back foam having 45 +/- 5 density foam used

there shall be cushion arm 25mm thick provided padded with high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered it complements the modish legs are made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h)

arms height @ 685mm back height @ 460mm ). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Leatherette 3 Seater Sofa size :- (W) 1965mm X (D) 965mm X (H) 940mm. Seating Height 480mm. Arm height 712MM. Seat Depth 570mm. Back Height 430mm. Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried german beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue

the frame shall be padded with high resilience polyurethane foam having 45 +/- 5 density in seat it shall be stack foam of 50mm thik

32mm thick back foam having 45 +/- 5 density Bid Details 14/110 foam used

there shall be cushion arm 25mm thick provided padded with high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered with premium leatherette

it complements the modish legs are made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h)

arms height @ 685mm back height @ 460mm ). The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Cafeteria Table 1. Dimensions: 1500mm (L) x 900mm (D) x 750mm (H) 2. The tabletop should be 25mm thick BWR (Boiling Water Resistant) plywood

ensuring durability and resistance to moisture. The surface will be finished with a 2mm laminate

providing a sleek and easy-to-clean finish. All edges will be fitted with PVC edging for additional durability and aesthetic appeal. Support Structure: The tabletop will be supported by two (2) mild steel C-shaped legs

each measuring 50mm x 50mm. The legs will be connected by horizontal connectors for stability. All metal components will be treated with a powder coating of 50 microns to enhance protection against corrosion and wear. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Cubical Cabin Table AND 1200HT PARTITIONS MAIN TABLE: 1500W X 750D X 750HT TABLE TOP SIDE COMP STORAGE 2D1F: 900 X 450 X 750HT Specification: Table top : Made of 25mm thick MDF As per IS 12406:2021

BIS certification board of approved shade . All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Main Frame : Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm MINIMUM thick 1200mm ht NEO based system with fabric above and lamiante below the table top.Fabric magnetic and glass markers are provided for each workstation. Support : Table top is supported on MS Powder coated Square single perform Legs which is constructed by 50Sq-16g ERW tube Wire Management : Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access. Side Composite Storage: Storage is made of 25mm thick top

18mm MDF As per IS 12406:2021

BIS certification with openable shutters

adjustable shelves

auto closing hinges

locking mechanism

finger groove handles and 2D+1F Drawer unit with Regular locking system."

placing in position and functional working Cabin Main Table - 1500W X 750D X 750HT SIDE COMPOSITE STORAGE - 900 X 450 X 750HT Specification: Table top: Made of 25mm thick MDF As per IS 12406:2021

BIS certification board of approved shade . All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: Table top is supported on MS Powder coated Square perform Legs which is constructed by 50Sq-16g ERW tube acts as vertical member & supporting ms cross beam

which is made of 40 x 20 16 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. Modesty Panel: MS square perforated metal modesty panels of 450mm ht are provided at passage side only. Wire Management. 450mm Anodised flip up Made of Aluminum in anodised finish

which Bid Details 15/110 has soft closure and three way wire acess & PVC cable dump. Vertebra for wire entry. Side Composite Storage: Storage is made of 25mm thick top

18mm MDF As per IS 12406:2021

BIS certification with openable shutters

adjustable shelves

auto closing hinges

locking mechanism

finger groove handles and 2D+1F Drawer unit with Regular locking system. "

placing in position and functional working the table shall be of size upto 3600 Width mm x 1200 mm Depth x 750 mm height. Top surface of the table shall made up50MM GABLE END 50MM MODESTY 25MM THICK of MDF As per IS 12406:2021

BIS certification (Medium density fibre ) board duly finished with Veneer and final coating f PU. The Main desk should contain in Smart Case space slides . The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm x 600 Height mm. Top shall be of MDF As per IS 12406:2021

BIS certification (medium density fiber) board duly finished with veneer and final PU polished Size of side unit top 1050 Width mm x 400 480 Depth mm x 550(not from ground with castors ).The main desk is provided with the wire management system also there is perfect storage side unit construction of side unit storage 1 fixed shelves with 1 sliding shutter

The Pedestal Shall Be Made Up of Medium Density Fibre Board. Pedestal Side

Facia Shall Be 18mm Thick And Pedestal Base On MS Powder Coated Legs. The Drawer Shall Be Operated with SS Handle and Easily Close & Open With The Assistance of Roller Channel And Ball Bearing Channel To Enable Smooth Operation. The Drawer Shall Have Central Locking Mechanism In Which All The Drawer Shall Be Synchronized Locked With One Single Key. The Pedestal Shall Be Mounted On 80mm Height

Powder Cotaed Legs.. Ms powder coated CPU trolley with castors. PVC keyboard tray. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge. "

placing in position and functional working structure of l- shape table top . Primary work surface over all size is 2400mm(l)x 1000mm(d)x 750mm(h) 50mm thick table top made of MDF As per IS 12406:2021

BIS certification board with natural 3mm venner work surface with p.u. polish. modesty is designed with leatherite patch. side pannel made of 40mm thick . Provision of side unit of size is 900mm(l)x 595mm(d)x 770mm(h)

construction of side unit storage 1 fixed shelves with 1 sliding shutter . A Fixed Pedestal Shall Be Provided With An Overall Size (400mm Length X 480mm Depth X 640mm Height). The Pedestal Shall Be Made Up of Medium Density Fibre Board. Pedestal Side

Facia Shall Be 18mm Thick And Pedestal Base On MS Powder Coated Legs. The Pedestal Shall Have 2 Nos. of Drawer i.e. 1 Box Drawer Size is 392 mm (D) X 179mm (H) And 1 Filing Drawer Size Should Be 392 mm (D) X 360mm (H). The Drawer Shall Be Operated with SS Handle and Easily Close & Open With The Assistance of Roller Channel And Ball Bearing Channel To Enable Smooth Operation. The Drawer Shall Have Central Locking Mechanism In Which All The Drawer Shall Be Synchronized Locked With One Single Key. The Pedestal Shall Be Mounted On 80mm Height

Powder Cotaed Legs.. Ms powder coated CPU trolley with castors. PVC keyboard tray. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

"Providing and fixing of modular table Dimensions: 1800mm (W) x 600mm (D) x 750mm (H) & UNIT SIZE- 600W X 450D X 750HT Construction: Tabletop and Sides: The tabletop and Bid Details 16/110 side panels will be constructed from 25mm thick MDF As per IS 12406:2021

BIS certification (Medium Density Fiberboard)

finished with 1.2mm thick laminate. Other Parts: All other components will also be made of 25mm thick MDF As per IS 12406:2021

BIS certification

Assembly Type: Design: The table will be of a knock-down assembly type . Storage Type: with 2 nos Drawers units and 1 filling folder unit with provided with fingure groove handle with suitable lock. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

placing in position and functional working Cafeteria Table 1. Dimensions: 1500mm (L) x 900mm (D) x 750mm (H) 2. The tabletop should be 25mm thick BWR (Boiling Water Resistant) plywood

ensuring durability and resistance to moisture. The surface will be finished with a 1.2mm laminate

providing a sleek and easy-to-clean finish. All edges will be fitted with PVC edging for additional durability and aesthetic appeal. Support Structure: The tabletop will be supported by two (2) mild steel C-shaped legs

each measuring 50mm x 50mm. The legs will be connected by horizontal connectors for stability. All metal components will be treated with a powder coating of 50 microns to enhance protection against corrosion and wear. The finish

design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge."

Installation and commissioning of SINGLE BURNER RANGE- Size-24"x24"x24. Top 16 swg ss sheet-304 grade

and cast iron Black enamel painted pan support

side panel 20 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe- 304 grade (38X38mm and 25x25mm Respectively). SS angle structure . One no high pressure gas burner and one pilot burner with all fittings. adjustable nylon bullet.. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge.

Installation and commissioning of SUPPORT TABLE - with 2 BS Size : 48""x24""x34""+6""Top 16 swg ss sheet-304 grade

bottom shelf - 18 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe- 304 grade (38X38mm and 25x25mm Respectively). SS chanel structure . adjustable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of TWO BURNER RANGE SINGLE SINK UNIT WITH- Size-48""x24""x30""Top 16 swg ss sheet-304 grade

and cast iron Black enamel painted pan support

side panel 20 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe- 304 grade (38X38mm and 25x25mm Respectively). SS angle structure .2 no high pressure gas burner and 2 nos pilot burner with require fittings

adjustable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of Working Table with sink 54"x24"x34"6" with CI WATER OUTLET VALVE.Top 16 swg ss sheet-304 grade

sink 18 swg 304 ss sheet

vertical and cross braching ss 16 swg square pipe- 304 grade (38X38mm and 25x25mm Respectively).All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge.

Installation and commissioning of Tilting Rice Boiler -100 Ltrs: 44 x 37X 36"". Doble jacketed ss sheet botoom 5 mm

304 inner body 3 mm ss sheet 304

outer insulated 16 swg sshet. Swetable gear box

Bid Details 17/110 vertical legs by ss 304 square 16 swg pipe

(38X38mm and 25x25mm Respectively) out let valve

one high pressure burner with individual control. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

"SS Drain Through Gartings : SS 304 angle frame 3mm( 25 x25mm) and ss 16 swg 304 grade 1"" and 3/4"" square pipe fabricated Size: 48""x12""x1""

gap to be maintained 20 mm . All necessary fittings and items will be provided for make it installed functional approved by engineer in charge."

" SS Drain Through Gartings : SS 304 angle frame 3mm( 25 x25mm) and ss 16 swg 304 grade 1"" and 3/4"" square pipe fabricated Size Size: 24""x12""x1"".Gap to be maintained 20 mm. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of DOSA/CHAPPTI PLATE -Size- 60""X24""X34"" WITH PUFFER.Chapati Plate3/4"" thick M.S.Plate on top with angle bracing. 20 swg S.S. 304 sheet panel .vertical legs by ss 304 square 16 swg pipe

(50 X50 mm and 25x25mm Respectively). SS angle structure . 3nos high pressure gas burner with pilot ignition & individual control system. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge. "

Installation and commissioning of CHAPATI ROLLING TABLE with 2nos bottom shelf Size : 48""X24""X34""+6"".Top 16 swg ss sheet-304 grade

bottom shelf - 18 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe(38X38mm and 25x12MM Respectively)- 304 grade . SS chanel structure adjustable nylon bullet. All necessary fittings and items will be provided for make it installed functional approved by engineer in charge."

Installation and commissioning of CHAPPTI COLLECTION TABLE TROLLEY -4 SIDE TURNEDUP: 30""X24""X34"". Top 18 swg ss sheet-304 grade

bottom shelf - 18 swg ss sheet -304 grade vertical ss 16 swg square pipe- 304 grade (38X38mm and 25x25mm Respectively) with 4 nos nylon wheel with brek. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of THREE BURNER CHINESE COOKING RANGE SIZE: 60""X30""X32+12 .Top 16 swg ss sheet-304 grade and 3 nos cast iron round and square pansupport with black enamel painted. side panel 20 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe- 304 grade . vertical legs by ss 304 square 16 swg pipe

(38X38mm and 25x25mm Respectively)SS angle structure . Three no high pressure gas burner and 3 no pilot burner adjustable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of CHAPATI ROLLING TABLE with 2 BS Size : 48""X24""X34""+6""Top 16 swg ss sheet-304 grade

bottom shelf - 18 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe(38X38mm and 25x12MM Respectively)- 304 grade . SS chanel structure adjustable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

SS Gas Tabdoor -: 30"x30"x34" Top 16 swg ss sheet-304 grade

side panel 20 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe- 304 grade(38X38mm and 25x25mm Respectively) . 4 nos MS wheel.All necessary fittings and items will be provided Bid Details 18/110 for make it installed/functional approved by engineer in charge.

Installation and commissioning of CHAPATI ROLLING TABLE with 2 BS Size : 48""X24""X34""+6""Top 16 swg ss sheet-304 grade

bottom shelf - 18 swg ss sheet -304 grade vertical and cross braching ss 16 swg square pipe(38X38mm and 25x12MM Respectively)- 304 grade . SS chanel structure adjustable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of SS 3 door worktop refrigerator: 72x28x32. Top and body made of 20 swg 304 ss heet

Compressor -Temparatuee Range 0C to + 10C WARRANTY FOR 3 YEARS FROM THE DATE OF SUPPLY All necessary fittings and items will be provided for make it installed functional approved by engineer in charge."

Installation and commissioning of4 Door vertical refrigerator : 48""x28""x78"" Complete body made of 20 swg 304 ss heet

Compressor - Imported - electric load 1.100Kw

AC .4 nos wheel . Temparature Range : 0C to +10C. WARRANTY FOR 3 YEARS FROM THE DATE OF SUPPLY All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of 2 Door vertical Deep freezer : 24x28""x78""Complete body made of 20 swg 304 ss heet

Compressor - electric load 0.500Kw

AC 4 nos wheel . Temparature Range: -17C to -12C WARRANTY FOR 3 YEARS FROM THE DATE OF SUPPLY All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of Chest freezer : 453 Ltrs-

Temparature range -23C to +8C Compreesor:

Electric load - 0.500 Kw

220 V. Size: 1402 x 666 x 940mm WARRANTY FOR 3 YEARS FROM THE DATE OF SUPPLY All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of MS Fabricated Rack with 1.5""x1.5 -6 mm MS angle and 18 swg MS sheet - 4 shelves duly enamel painted. Size: 44""x 30""x 72"" All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning ofAtta Maida Bins: 24""x24""x30""; Structure made of ss chale 304 16 swg

and rest body made from 304 ss sheet 18 swg. One hasbold should be provided with top door for locking arrangement. 4 nos ss vertical legs 16 swg 304 pipe

(38X38mm). 4 nos 4"" dia nylon wheel with break. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of SS Soiled dish landing table with garbage chute 48""x24""x34""+6"": Structure made from ss 16 swg

top made of 304 16swg

vertical and cross braching made of 16 swg 304 square pipe.(38X38mm and 25x25mm Respectively)4 nos adjustable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning ofSS 3 Sink washing unit with CI water outlet Ball Valve.Structure made from ss 16 swg

top made of 304 16swg

vertical and cross braching made of 16 swg 304 square pipe.(38X38mm and 25x25mm Respectively) Sink : 18""x18""x12 - 3 nos by 304 18 swg ss sheet. 4 nos adjustable nylon bullet. All necessary fittings and items will Bid Details 19/110 be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of SS Pot rack-4 shelf : 60""x30""x66"". Made of ss 304 16 swg ss sqaure pipe

(1.5 x 1.5"") and4 nos shelf made of 1""x1""x16 swg 304 ss square pipe. 4 nos adjsutable nylon bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of Clean dish and glass rack - 4 shelf : 44""x16""x66"". 4 nos perforated shelf by 304

18 swg ss sheet. 4 nos vertical made of 16 swg 304 square pipe. (38X38mm )4 nos nylon adjustable bullet. All necessary fittings and items will be provided for make it installed functional approved by engineer in charge."

Installation and commissioning of SS Bain marie with 10 vessel : 84""x26""+10""x34"". structure made of ss 304 16 swg ss chanel

water tank made of 16 swg 304 sheet

3 side cover bottom shelf by 304

20 swg ss sheet : with tray rail made of 304 ss 16 swgss pipe

10 nos vessel 1/2- 6nos and 1/1-2 nos - by 304 20swg ss sheet. 4 Kw

heater with theromostatic control 220V. Vertical legs 304 16 swg ss square pipe with nylon adjustable bullet. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of SS Soiled dish collection Trolley 3 Tier : 36""x24""x34""Top 18 swg ss sheet-304 grade

bottom shelf - 18 swg ss sheet -304 grade vertical ss 16 swg square pipe- 304 grade (38X38mm and 25x25mm Respectively) with 4 nos nylon wheel with brek. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of Water cooler 80 Ltrs - 2 nos Faucet (80 Ltrs storage and 60 Ltrs supply)with 3 stage (Sediment filteration

carbon filteration and UV filtaration) inbuild RO sysem

body complete 304 stainless steel. Operation Temperature- 15C to 45C

electric load - 250 Watt

220 V. : Size- 660 x480x1355mm All necessary fittings and items will be provided for make it installed functional approved by engineer in charge."

Installation and commissioning of SS paltform trolley

made of ss Angle 304 and ss 18 swg. Ss sheet 304 grade

ss pushing round hnadle

4 nos 6"" dia x1""thick wheel with break .Size- 36""x24""x 10""+30"". Load Capacity - max- 150 kgs. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of L.P.Gas PIPELINE MANIFOLD SYSTEM with all necessary fittings : Non retu rn valve- 16 nos

Click-on adopter -16 nos

Fleaxable burner pigtail-3feet long-16 nos

manifold 1"" dia valve - 2nos

I- satge reglator -1 no

II- stage regulator -1No

pressue guage -(0-60 PSI)-1 no

mainline shutt-off valve 1 "" dia 1 no

Manifold - 8x2=16 Cylinder - complete set- 1no

Require. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge. Vendor will take all necessary statutory approvals (FIRE NOC ect) for making it functional"

"1"" dia L.P.Gas pipeline TATA

ERW. High thick

fixing testing and painting JOB SHOULD BE DONE AS PER IOC APPROVED NORMS IS6044 PART- I. All necessary fittings and items will be provided for make it installed functional approved by engineer in charge. Vendor will take all necessary statutory approvals (FIRE NOC ect) for making it functional"

Installation and commissioning of MS Fabricated Cylinder room-Double tier : Cap-16 cylinder.Made Bid Details 20/110 of 18 swg. MS sheet

structure made of 40x40x3mm MS agnle

duly enamel painted finish with locking system. Size: 70""L x 36""x 90"" All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of HOT AIR VENTILATION SYSTEM: With 6 nos ss 202

20wg ss hood and require ss filter

and one no AXIAl flow fan static pressure 15 mm with 3 HP

1440 RPM with crompton motor

Aluminium Impeller - dynamic balancing

440 V. GI. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

Installation and commissioning of ductline made of GI 22 SWGwith necessary fittings. Size specification as per approved design. All necessary fittings and items will be provided for make it installed/functional approved by engineer in charge."

"Providing and fixing External Signage's made of SS 304 (brush finish) front 0.8mm thick & side 0.6mm thick sheet for letters with raising(letter depth of 37-50mm). Including all fittings

fabrication.The signage will be front illuminated/hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl for desired colour with premium make LEDS and IP 67 Grade powersupply fixed on the wall with necessary fixtures. Size approx 10 SQ FEET . The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"Providing and fixing External Signage's made of SS 304 (brush finish) front 0.8mm thick & side 0.6mm thick sheet for letters with raising(letter depth of 37-50mm). Including all fittings

fabrication.The signage will be hollow illuminated. Sides of the signage to be made of 4 mm thick acrylic. UV Print for desired colour with primium make LEDS and IP 67 Grade powersupply fixed on the wall with necessary fixtures. Size approx 9 SQ FEET . The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"Providing and fixing Logo Signage's Base made of ACP Cladding 4mm thick ACP

0.5mm aluminium foil with MS SHS 37x37 mm frame. MS frame to be duly treated with 2 coats red oxide primer and 2 coats of white enamel paint. Logo + Text : 3d Letters with translucent vinyl of MAKE primium on 10 mm acrylic sheet

4mm inside and 6mm outside of ACP. The Lighting for logo shall be achieved through make LEDS and IP 67 Grade powersupply. Size approx 1200X1500mm . The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"12mm WPC Letter

letter size upto - 12"" -16"" - Providing

fabricating and fixing of 3D letter which will be made 12mm thick WPC board

cutting through CNC router machine and polished through CNC sander machine and exterior will be PU paint finish. The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"12mm WPC Letter

letter size upto - 08"" -10"" - Providing

fabricating and fixing of 3D letter which will be made 12mm thick WPC board

cutting through CNC router machine and polished through CNC sander machine and exterior will be PU paint finish. The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"12mm WPC Letter

letter size upto - 06"" - Providing

fabricating and fixing of 3D letter which will be made 12mm thick WPC board

cutting through CNC router machine and polished through CNC sander machine Bid Details 21/110 and exterior will be PU paint finish. The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"Planter 3Ft - Providing

fabricating and fixing of Pot

made of glass fiber reinforced polymer (FRP) Composite of resine

indentry and all other materials etc.. Pot as per design with glass fiber reinforced plastic molded skins and a special sandwich core

external portion will be finished with artistic paints as per design/asthetic value. The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"Planter 2Ft - Providing

fabricating and fixing of Pot

made of glass fiber reinforced polymer (FRP) Composite of resine

indentry and all other materials etc.. Pot as per design with glass fiber reinforced plastic molded skins and a special sandwich core

external portion will be finished with artistic paints as per design/asthetic value. The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "

"Wooden Planter 1.5Ft - Providing

fabricating and fixing of Pot

made of glass fiber reinforced polymer (FRP) Composite of resine

indentry and all other materials etc.. Pot as per design with glass fiber reinforced plastic molded skins and a special sandwich core

external portion will be finished with artistic paints as per design/asthetic value. The finish

design & size is tentative and could vary +_ 5% and to be approved by engineer in charge. "