SPECIAL REPAIRS TO ARJAN HALL IN TRAINING WING

Amount

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

M & L for treatment of soil under existing floors using emulsion @ 1 ltr per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors etc all as specified and as directed by Engr-in-Charge.

M & L for non-skid ceramic coloured tiles 7 to 8mm thick (squire/rectangular)area of each tiles exc. 0.11sqm but not exc. 0.18 sqm in floor etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including 15mm thick screed bed or bedding layer of in CM 1:6 all as specified and as directed.

M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement withadmixture of pigment to match the shade of granite stone including 15mm thick screed bed or bedding layer of in CM 1:6 all as specified and as directed.

Dismantling of boarding , any description , fixed in any position (as in wall panelling and ceiling) with nails including battens etc all as specified.

Taking down cement plaster on brick or stone walls, ceilings, etc including racking out Joints, hacking for key, scrubbing down with water, etc,.

M & L Rendering 5 mm thick in cm (1:3) on fair faces of brick work or concrete ceiling surfaces, finished even and smooth without using extra cement

M & L Rendering in CM 1:6, 10mm thick on fair faces of brick work or concrete wall surfaces, finished even and smooth without using extra cement

M & L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces, plastered surfaces should be even and smooth with out using extra cement etc all as specified and as directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of Oil Bound Distemper over a coat of primer over 2 to 3mm thick wall care putty all as specified.

All as per item No 10 above but on ceilings.

M & L for preparing of old painted surfaces of wall and applying one coat of oil bound distemper matching with existing colour etc complete all as specified and directed.

M & L for preparing of old painted surfaces of ceilings and applying one coat of white wash etc complete all as specified and directed.

Taking down chowkhats or frames with shutters (with out taking off shutters from the frames) size exc 1.50 sqm and not exc 4.00 sqm each and all as specified and directed.

Taking down chowkhats or frames with shutters (with out taking off shutters from the frames) size not exc 1.50 sqm each and all as specified and directed.

M & L for 12mm thick prelaminated particle board, exterior grade , prelaminated both side with decorative choice lamination and fixefd with screw to frame work etc., complete all as specified and as diirected.

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified and as directed by Engineer- in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement , suppling & fixing in the frame at site as per specification & drawing etc., complete all as specified and as directed by Engineer-in-Charge.

Material and labour for second class hard wood plain , solid, stright , chowkhats and frames, wrought, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for second class hard wood 40mm thick plain framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board commercial face veneers , supplied and fitted to chowkats all as specified and as directed by Engineer-in-Charge.

S & F 100 mm size Butt hinges medium weight cold rolled mild steel.

S & F 200 mm size Aluminium anodised barrel tower bolts extruded section.

S&F 150 mm size Extruded aluminium alloy handles fabricated type anodised.

S & F 300 mm long Aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy .

Material and labour for preparation of new wood surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed by Engineer-in-Charge.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples

Taking up or down steel tubing and connections, removing to store for taking in account of credit for 15mm bore

All as per item No.27 above but for 20 mm bore

S&F steel tubing medium grade galvanised with all fitting and fixtures complete to walls and or laid in floors 15mm bore

All as per item No.29 above but for 20 mm bore

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm bore

All as per item No.31 above but for 75 mm bore

S&F PVC (SWR) bends any radius 110 mm bore

S&F PVC (SWR) bends any radius 75 mm bore

S&F grating doom 125 mm dia with waste hole of PTMT (minimum weight 40 gms)

S& F in repair Vitreous China wash basin, white, flat back, size 580x450mm (for Hospital use) excluding taps, waste, chain and plug and porcelain stopper but including brackets Make : CERA Model No: F5005102 or equivalent in HIndware, CERA, Parryware, Hindustan Sanitaryware.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including seat cover and flush pipe etc complete all as per specified and as directed by Engineer-in-Charge. Make : CERA Model No: S1021103 or equivalent in HIndware,Jaquar , Parryware, Hindustan Sanitaryware.

M & L for PVC (SWR) multi floor trap of 75mm dia with grating including jointing with solvent cement etc complete,

M & L for PVC (SWR) gully trap of 125/110mm dia includingsetting jointing with solvent cement etc complete,

S & F Unplasticised PVC pipes 50mm dia of pressure rating 10 kgf /cm2 fixed complete to walls, ceiling or in floors etc complete

S & F in repairs PVC valveless, syphonic action type, flushing cistern of 10 Ltrs capacity , low level , white, with inlet , ball valve, float and handle including brackets and flush pipe etc complete all as specified and as direted by Engineer-in-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm

S & F in repairs towel rail, 20mm dia, D type, 60cm long of brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats. Make :CERA Model No: F5004103 or equivalent in Prayag Polymers Pvt Ltd (Symet), Shakti

S&F in repairs Bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. Make : CERA Model No: F1015163 or equivalent in Leader,Jaquar, Zoloto, Seico, Marc

S&F in repairs chromium plated angle valves, cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size. Make : CERA Model No: F1015201 or equivalent in Leader, Zoloto, Seico, Marc

S&F in repairs Pillar taps fancy type cast copper alloy, with capstain head, chromium plated screwed down high pressure, with long shanks and fly nuts screwed for iron pipe and fixed 15 mm bore. Make : CERA Model No: F1015101 or equivalent in Leader, Zoloto, Seico, Marc

S & F in repair glass corner shelf assembly of size 225 x 225 mm consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard and railing etc., complete.

S & F in repairs vitreous china Urinal, Half stall type, white complete including providing and fixing plugs , bedding urinal against wall in cement mortar 1:2 , securing urinal to plugs with and including 60mm long brass screws , pointing around urinal back in cement , flushing pipe, grating and union for discharge pipe. etc complete with other necessary fittings and fixtures all as specified and as directed by Engineer-in-Charge.

S & F in repairs concussive push cock button taps of 15 mm bore of cast copper alloy, screwed for iron pipe and fixed etc complete all as specified and as directed.

S&F in repairs brass chromium plated health faucet with hand held and spring operated control valve with PVC flexible pipe connection of suitable length as directed fixed to 15 mm bore pipe. Make : CERA Model No:F8030103 or equivalent in Jaquar ,Dolphin/Zoloto

S&F in repairs white toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws.

M & L for Glazed ceramic coloured tiles on vertical surface 350 x 450 mm x 8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thick (above or below the ground level) as in existing CC hardstanding, base of fountain and other similar work etc complete.

M&L hardcore with broken stone or boulders of gauge not exc 63 mm deposited spread and leveled in layers not exc 15 cm thick watered and rammed to a true surface .

M & L for Cement concrete type C2, 1:3:6 (40mm graded stone aggregate) 75 mm thick as in floor including necessary form work as required.

M&L for chequered cement concrete tiles 30cmx30cmx25mm thick, set jointed and pointed in neat cement slurry with grey cement and pigment in floors including 20 mm thick screed bed or beding layer in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins , arches, pillars etc complete.

M & L for brickwork with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 all as specified and as directed.

M & L for 10mm thick rendering in cement mortar 1:4 on fair faces or brick work or concrete surfaces, rendered surfaces is to be finished even and smooth without using extra cement.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over one coat of primer all as specified.

Supply and installation of False Ceiling System having tiles ADVANTAGE E with micro look edge and 15mm thickness tiles or equivalent make, easily demountable tile, 15mm Gypsteel pre coated GI T Grid system in 600x600mm module which includes providing and fixing wall angle along the perimeter of the room with help of nylon sleeves and wooden screws at 300mm centers. Then suspending the main tee of size from the soffit with help of soffit cleat, rawl plugs and wire rod with Leveling spring clip at 1200mm c/c. 1200mm Cross Tee is then interlocked into the pre-cut slots in the main Tees at 600mm centers in direction perpendicular to the main Tee to make a grid of 600x1200mm. Finally 600mm Cross tees are then interlocked into the pre cut slots in the 1200mm tees at 1200mm centers and in direction parallel to the main tee to make a module of 600x600mm . Cross Tees having length more than 600mm are to be supported independently. Then laying Tile Ecophon 15mm Advantage E 595x595mm tile, Option of weekly dusting, vacuum cleaning, manufactured from High density glass wool, visible surface is a batch painted glass tissue in white, back of the tile covered with glass tissue. 83% light reflectance. Tiles classified under sound absorption class A with "alpha w " value of 0.95 at minimum 200mm o.d.s. Sound absorption test results measured according to EN ISO 354 and classification according to EN ISO 11654 and the single value rating for NRC value - 0.9 according to ASTM C 423 . Tiles should have white colour " White 500 " nearest NCS colour sample S 0500 - N with . Tiles withstand a permanent ambient RH up to 95% at 300C without sagging, warping and delaminating ( ISO 4611). Thermal resistance (Lambda value - 0,035-0,04 W/mK). Certified by the Indoor Climate labeling , emission class M1 for building materials and recommended by Swedish Asthma and Allergy Association. Product Certified under GRIHA council of India for Green Ratings . Fully recyclable . The glass wool core of the tiles is tested and classified as non combustible according to EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501 - 1 - European Standard. Tiles should have a re-cycled content of more than 70% Systems are classified as fire protective covering according to NT FIRE 003. Rate to be inclusive of approved GI exposed grid system as per manufactures specifications.

M & L for False ceiling with 12.5mm thick Gypboard plain board (Make Saint Gobain Gyproc India) including all necessary fittings and fixtures , which includes gypsteel ULTRAtm CRP surface ribbed perimetre channels (having one flange of 20 mm and another flange of 30 mm and a web of 27 mm) along the primeter of ceiling screw fixed to brick wall/ partition with the help of nylon steeves and screws, at 610mm centres.Then suspending Gypteel ULTRA tm CRP surface ribbed intermediate channels of size 45mm (with two flanges of 15mm each) from the soffit at 1220mm centres with Gypsteel ULTRA tm CRP surface ribbed ceilling angle of width 25mm x 10mm fixed to soffit with GI cleat and steel expansion fasteners (Mfg by Saint Gobin Gyproc). Then Gypsteel ULTRA tm CRP surface ribbed Ceiling section of having web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the Gypsteel ULTRA tm intermediate channel with the help of connecting clip and in direction prependicular to the Gypsteel intermediate tm channel at 457mm centres. Single layer of 12.5mm tapered edge Gypboard Plain (confirming to IS 2095 part 1 1996) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attatchment. Finally square and tapered edges of the boards are to be jointed and finished so as to have flush look which includes filling and finishing with Gyproc jointing compound, Gyproc joint paper tape. (As per recommended practices of Saint- Gobain Gyproc India) incl Painting of Gypboard Ceiling/Partition/Walls with two coat of (Birla wallcare putty) two coats of primer and two coats of EMULSION (Asian) with roller finish.

Supply and installation of False Ceiling System having tiles of Black SOMBRA A or equivalent make, 15mm thickness, square edge tiles, The 'T' grid system Black 24mm precoated GI T Grid system in 600x600mm module which includes providing and fixing wall angle along the perimeter of the room with help of nylon sleeves and wooden screws at 300mm centers. Then suspending the main tee of size from the soffit with help of soffit cleat, rawl plugs and wire rod with Leveling spring clip at 1200mm c/c. 1200mm Cross Tee is then interlocked into the pre-cut slots in the main Tees at 600mm centers in direction perpendicular to the main Tee to make a grid of 600x1200mm. Finally 600mm Cross tees are then interlocked into the pre cut slots in the 1200mm tees at 1200mm centers and in direction parallel to the main tee to make a module of 600x600mm . Cross Tees having length more than 600mm are to be supported independently. Then laying 20mm Black Sombra Tiles 595x595mm Easily demountable, Option of weekly dusting, vacuum cleaning. manufactured from high density glass wool . Visible surface is a matt black batch painted glass tissue and the back of the tile is covered with glass tissue. 3-4% light reflectance. Tiles should be classified under sound absorption class A with "alpha w " value of 1 at minimum 200mm o.d.s. classification according to EN ISO 11654, and the single value ratings for NRC value 0.9 according to ASTM C 423. Tiles withstand a permanent ambient RH upto 95% at 300c without sagging, wraping or delaminating (ISO 4611). Thermal resistance (Lamda value - 0,035-0,04 W/mK) Certified by the Indoor Climate Labelling, emission class M1 for building materials and recommended by the Swedish Asthma and Allergy Association. Fully recyclable. Glass wool core of the tiles is tested and classified as non- combustible according to EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501 - 1 - European Standard. Systems are classified as fire protective covering according to NT FIRE 003. Rate to be inclusive of approved GI exposed grid system as per manufactures specifications

S & F solid PVC wall lining / paneling consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification etc complete all as specified and as directed by Engineer-in-Charge.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on wall to make PVC frame as per specification and as directed by Engineer-in-Charge.

Ecophon Akusto™ Wall A Tech Akutex FT 1200 x 2700 mm with 40 mm natural square edge, manufactured from high density glass wool, demountable panels (with standard fabric approved by the architect) & wrapped around in concealed system with PVC grippers of 18mm screwed on the MDF or wood baton of 22 mm. The panels are stuck using SR adhesive in the cavity created by Mdf batons as per the design size and finally fabric is rolled and stretched through the PVC gripper teeths to conceal the panels and give the approved fabric finish look. The back surface on the civil wall or gypsum drywall to be fixed WPC plywood of 12 mm pre provided wherever the panelling has to be done. ODS of system - 43 mm inlcuidng fabric apart rom the 12mm ply backing behind Manufacturing- Manufactured in Sweden, production unit is ISO 14001 certified. Acoustics-Sound absorption(Alpha W) - 1 at minimum 43 mm o.d.s as per EN ISO 354 Acoustics-Sound absorption Class - Class A at 43 mm o.d.s as per EN ISO 11654, NRC - 0.95 Articulation Class - 230 as per ASTM E1111, ASTM E1110 Humidity Resistance -Permanent ambient RH upto 95% at 300C without sagging, warping or delaminating (EN 13964:2014). Fire Safety- Tested and classified as non combustible according to EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501 -1 -European Standard. Indoor Health & Well-being - Complying with the French regulation on VOC emissions, A+ level.Certified by the Finnish Building Information Group (RTS) with the M1 label. Free from substances of very high concern (SVHC) above 100 ppm as defined by the European REACH regulation (No1907/2006). Product Certified under GRIHA Council of India for Green ratings. Environmental Product declaration (EPD) acc to international ISO 14025 & EN 15804 series of standards. Circularity - Re-cycled content of more than 70% CE marking - CE-marked according to the harmonised standard EN 13964:2014 Maintenance - Daily dusting & vacuum cleaning, weekly wet cleaning

M & L for providing and fixing solid UPVC foam flooring made of solid UPVC foam proifile with homogenous fine cellular structure having smooth outer integral skin having 250mm wide T & G design with 12mm thickness cornice profile 39mm x 10mm and internal corner 15mm x15mm are used for covering corner joints, flooring joints and column joints. Grid work is made of shall be made of solid uPVC foam profile having 35mm width and 17mm thick. Batten aligned horizontally along the wall with 50mm gaps between battens to provide the cushion and impact resistance. Flooring can be masde in natural finish / wood veneers emboss finish design as well as with PU coating for additional abrasion (optional) as per instructtion of the Engr-in-Charge.

Removal of old demolished bldg material out of MD land to a distance exc 1.50 Km but n. exc 5km and depositing where directed. Note : Location and getting permission of depositing the excavated material / old debris for disposal out side MD land from concerned authority shall rest with contractor on his own arrangement.

S&F Anodised aluminiam frame for sliding doors , Partition Wall, window, ventilators with one or more rebeats including joining clear for fixing etc.completed all as specified.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150 mm long ( (1 No), hinges type B-21 100 mm long (2 Nos) suitable handle (01 No) complete all as specified and as directed

M & L for vitrified ceramic light shade tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm but not exc 1.00sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match etc., including 15mm thick screed bed or bedding layer of in CM 1:6 all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendents, regulators, sockets, etc all as specified and directed.

Taking down sub main wiring of any size includig GI/copper earth continuity conductor in PVC conduit on wall/roof making good to disturbed surfaces all as directed.

Taking down old ceiling fan / exhaust fan and dismantling of blades, depositing to AGE E/M store yard.

Material and Labour for point wiring with PVC unsheathed multi standard 1.5 Sqmm FRLS Cable 1100 Volts grade with multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic PVC conduit with all accessories concealed in walls and including provision of 1.5 Sqmm single core PVC insulated FR cable 1100 Volts grade with multistranded copper conductor cable as earth continuvity complete all as specified and directed :-

Five light point controlled by one, one way switch

One light point controlled by one, one way switch

One fan point controlled by one switch

One switch socket outlet 5A on same board with other switch

One switch socket outlet 5A independent with cable 1.5 Sqmm

All as per Item No. 76 described here-in-before but with copper conductor cable FRLS 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including provision of 2.5 Sqmm PVC insulated copper conductor cable as earth conductivity conductor on independent board.

M& L for Sub main wiring with 2 runs of 6 sqmm single core PVC insulated unsheathed multistranded copper conductor cable 1100V grade FRLS drawing in and including PVC rigid medium grade conduit concealed in wall of suitable size complete including provn of 6 sqmm PVC insulated copper conductor earth continuity wire NOTE ;- One runs of three single core cable and conduit shall be measured as one unit

M& L for Sub main wiring with 4 runs of 4 sqmm single core PVC insulated unsheathed multistranded copper conductor cable 1100V grade FRLS drawing in and including PVC rigid medium grade conduit concealed in wall of suitable size complete including provn of 2x4 sqmm PVC insulated copper conductor earth continuity wire

S & F Switch modular 6A one way, 1 module Make :- Legrand, Crabtree, Anchor

S & F Switch modular 6A one way, 1 module Make :- Legrand, Crabtree, Anchor

S & F Socket, 6A - 2/3 pin combined 2 module Make :- Legrand, Crabtree, Anchor

S & F Socket, 6 / 16A - 2/3 pin combined 2 module Make :- Legrand, Crabtree, Anchor

S & F Ceiling fan step regulator modular 120W - 2 module Make :- Legrand, Crabtree, Anchor

S & F 33/40 W LED slim panel light 2 x 2 recess mounted luminaire with frame and electronic driver unit and two core 0.5sqmm with flexible connecting cord complete all as secified and diected Cat No. LPS 40WH of Lukar or equivalent in Havels, Philips, Bajaj

S&F TARA-M/20W, LED tube light fitting 1x20 Watt MS white powder coated decorative LED T8 batten with PC tube complete with two core 0.5 sqmm white flexible connecting cors all as directed. Make :- C & S Cat No. LTDC0161820WLED + LT4F20WLEDT8/WD or Luker Cat No. LT820T + LLTS1 or equivalent in Havels, Philips.

S&F indoor foot light 3W concealed type including electronic driver unit and two core 0.5 sqmm with flexible connecting cord and other strandard accessories complete all as specified and directed. Cat No. Havells ES 50 or equivalent in Luker, Crompton, Bajaj.

S&F ceiling fan AC single phase 230 Volts 1200mm sweep BEE 5 star rated complete with two core 0.5 sqmm with flexible connecting cord and other strandard accessories complete all as directed. Cat No. Havells ES 50 or equivalent in Luker, Crompton, Bajaj

S&F exhaust fans heavy duty AC single phase 230 Volts of 300 mm sweep 1400 RPM with louver shutter with two core 0.5sqmm with flexible connectong cord and other standard accessories complete all as specified & directed. Make:- Havells, Bajaj, Crompton

S & F triple pole and earth enclosure with a three pin and earth plug with socket complete with one triple pole MCB 20A

Supply and fix sheet metal enclosure double door with distribution board vertical (DB) VTPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 08 way double door suitable for fixing MCCB 63 Amps as incommer and MCBs TPN as out going complet, fixed on wall and connecting with all electric connections/circuit complete all as directed by Engineer in charge. Make: Indoasian Cat No. 811893 or equivelent in Havells, Standard.

S&F sheet metal enclosure double door, acrylic window type for MCB DB TPN 4 way 415V with 200 A bus bar including connecting up circuits all as directed . Make:- Havells, Legrand, Crompton

S&F sheet metal enclosure factory made double door MCB DB SPN 8 way 240V with 200 A rated bus bar complete including connecting up all circuits all as directed. Make:- Havells, Legrand, Crompton

Supply and fix sheet metal enclosure double door with distribution board vertical (DB) VTPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 08 way double door suitable for fixing MCCB 63 Amps as incommer and MCBs TPN as out going complet, fixed on wall and connecting with all electric connections/circuit complete all as directed by Engineer in charge. Make: Indoasian Cat No. 811893 or equivelent in Havells, Standard.

Supply and fix 4 pole MCCB 63 A ,50 Hz,415 V with rupturng capacity 25 kA complete all as specified and directed. Make: Indoasian, Havells, Legrand.

Supply and fix MCB TPN 32 Amps, 415 Volt C curve all as specified and directed. Make: Indoasian, Havells, Legrand

Supply and fix MCB TP 32 Amps, 415 Volt C curve all as specified and directed. Make: Indoasian, Havells, Legrand

Supply and fix MCB SPN 32 Amps, 415 Volt C curve all as specified and directed. Make: Indoasian, Havells, Legrand

Supply and fix MCB SP 32 Amps, 415 Volt C curve all as specified and directed. Make: Indoasian, Havells, Legrand

S & F ceiling rose , 3 phase/PVC/polycrbonate, isolated body

M&L for Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in Electrical Plate No 3 of SSR Part-I and testing on completion.

M&L for dismantling the split AC of capacity 3 TR both indoor and outdoor units carefully and kept in safe custody & refixing the same after completion of repair work complete all as specified and directed.

M&L for 5mm thick sheet glass, ordinary quality and glazing with aluminium beading in sqare exc 0.5 Sqm each panes complete all as specified and directed.

SEMBA ELECTRICALS

p.chinnasamy

TECKXPERT ENTERPRISES