Certain B/R and E/M repair works in OTM and Md Accns under GE (Utilities) Udhampur

Amount

Demolition of brick work or stone /boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) in ground floor and in pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided, complete all as specified and directed by Engr-in-charge.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

All as per Ser item No 4.00 here-in-before but except bricks, complete all as specified and directed by Engr-in-charge. Note : Old bricks obtained against demolition shall be used.

Walling of random rubble stone masonry uncoursed with best quality lacally available harder stones such as granite, trap, basalt stone etc, wellbonded bedded and solidly hearted, built in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

All as per Ser item No 6.00 here-in-before but except stones, complete all as specified and directed by Engr-in-charge. Note : Old stones obtained against demolition shall be used.

Removal of existing old water proofing treatment as in roofs and Preparing RCC roof slab top by wire brushing and cleaning the dust and foreign materail etc , there after applying 15mm thick cement plaster on concrete surface in CM 1:4 finished even and smooth without using extra cement using water proofing compound, complete all as specified and directed by Engr-in-Charge.

Preparing and Cleaning the dust and foreign materail etc complete for roof surfaces (plaster/concrete) and applying a coat of hot blown bitumen 85/25 grade @ 1.20kg/Sqm and there after laying of a layer of APP based polymeric membrane (five layered with centre core as 100 microns high molecular high density polyethylene film) weighing not less than 3.5 kg/Sqm and reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid on bituminous surface by press application method with 75mm side overlap and 100mm end overlap. The membrane has to be laid with LPG torch application and overlaps sealed and finished neat, after that applying one coat of bitumen 85/25 grade on top surface @ 1.20 kg/Sqm and blinded with premier dry sand @ 0.5 kg/Sqm dusted over bitumen coat, incl.applying two coats of aluminium paint over roof treatement, complete all as specified and directed by Engr-in-charge. Make- STP/IWL

Removing existing paint by scrapping with TruCare Wall Sander L-01/H-01 (having mechanical vacuum mechanism) or equivalent as recommended by the manufacturer and approved by the GE, having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. by skilled labour, complete all as specified and directed by Engr-in-charge.

Providing and applying 1mm thick waterproof cement based putty @ 1Kg (undiluted) per Sqm of Asian Paints or its equivalent over the plastered/ old painted wall after scrapping to prepare the surface even and smooth, complete all as specified and directed by Engr-in-charge. Step 1) Mix the putty powered by adding 40-50% water and mix it with Putty mixer (Trucare Putty mixer capacity of min 2.5 kg putty per minute). Step 2) Apply the first coat the prepared mixer with the help fully automatic airless spray machine of putty application of Asian Paints Trucare Graco spray Machine (Model: EH 230 DI) or equivalent as recommended by the manufacturer and approved by the GE, having DC electric motor of 3.3 KW having flow speed of max 6 Itrs per minutes with a maximum pressure 230 bar having maximum tip size 0.041" or oy manually. Step 3) Allow 6-8 hrs time to dry the putty surface.

Sanding of the putty surface with Asian Paints TruCare wall sander: L-01/H-01 or equivalent (having mechanical vacuum mechanism) or equivalent as recommended by the manufacturer and approved by the GE, having RPM not less than 1500, sanding pad of 240 Grit or above having dia of 7"/9" to make the surface free from dust etc. by skilled labour, complete all as specified and as directed by Engr-in-Charge.

Providing and applying, one coat of acrylic waterbased interior/exterior grade primer @ 0.8 itr (undiluted)/10Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalent as recommended by the manufacturer and approved by GE, having an electric motor of min 1 HP with a flow speed of min 1 itr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent coats, complete all as specified and directed by Engr-in-charge.

Providing and applying two coats of smooth acrylic emulsion with rich matt firish having voc less than 50 grams per Itr complying leed criteria @ 1 Itrs (undiluted)/10Sqm diluted with water in 2:1 ratio applied over priming ccat with fully automatic airless spray machine of paint application of Asian Pairts Trucare Graco or equivalent as recommended by the manufacturer and approved by the GE, having an electric motor of min 1 HP with a flow speed of min 1 Itr per minute having a pressure of 3300 PSI A low 6-8 hrs to dry the surface in both the coats of paint, complete all as specified and directed by Engr-in-charge. Make: "Apex Ultima" of Asian Paint/"Weathercoat All Guard" of Berger Paints/Excel Total of Nerolac Paint

Note: (Applicable to Ser items No. 10 to 14 Here-in-above) (a) At the time of uploading bids each tenderer shall upload a copy of MOU towards triparty agreement between tenderer. Manufacturer of Paints from Asian Paints/Berger Paints/Goodlass Nerolac Paints and their Applicators, for material and execution of work from any of the said manufacturers. Financial Bids of only those bidders shall be admitted whosoever shall upload a legitimate MOU. (b) Terms of the MOU so entered between tenderes, Applicators and Manufacturers mentioned above shall also cover the guarantee from manufacturer of paints for any defect in work executed by their applicator for a period of 3 Years. All other aspects with regard to payment, execution of work or other legal points shall be solely as decided between the tenderer, Paint manufacturer & Applicator. Department shall in no way be responsible for any complicacy arising at a later stage between the parties to MOU with regard to payments or execution of work. (c) (Applicable to Srl items other than covered under Note 1 to 5 here-in-before). The necessary steel scaffolding upto G+3 storeyed wherever required to execute the work shall be provided by the contractor with all safety equipments and the cost of providing scaffolding & safety equipments shall be deemed to be included in the quoted rates of the contractor and nothing extra shall be admissible on this account. (d) The work shall be executed in restricted area and head loss etc. The contractors are advised to consider this aspect while quoting his rates. Nothing whatsoever on this account shall be admissible at later stage.

Supply only integral water proofing compound as per latest IS specification, complete all as specified and directed by Engr-in-charge.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engr-in-charge.

Rolled mild steel work as in roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to grade Fe-410 W(Gde-E-250) quality-A, steel work, complete all as specified and directed by Engr-in-charge.

Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to grade Fe.290.Gde-E-165, steel work, complete all as specified and directed by Engr-in-charge.

Welded steel wire fabric supplied and fixed to wood or steel members weight not exc. 4 kg per square metre, complete all as specified and directed by Engr-in-charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified and directed by Engr-in-charge.

M&L prepainted galvalume aluminium zink coating GI based corrugated steel sheet 0.6mm thick mangalore pattern of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-charge.

M&L prepainted galvalume aluminium zink coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-charge.

Material & Labour 18-20mm thick machine cut marble [Baroda Green / Udaipur Green] with granite polish stone slab as in kitchen shelf or cooking platform, laid over and including cement screed bed or base 20mm thick in CM 1:4 laid and jointed with cement slurry mixed with colouring pigment to match the colour or shade of the slab including rounding outer edges of stone half round by grinding machine, complete all as specified and directed by Engr-in-charge.

M&L for Bitumastic gola, with 80/25 bitumen and coarse sand mixture 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces, complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exceeding 1.50 Sqm each and removing from site, complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exceeding 1.50 Sqm each but not exceeding 4 Sqm each and removing from site, complete all as specified and directed by Engr-in-charge.

Taking down chowkats of any descrition exceeding 1.00 Sqm and not exceeding 2.00 Sqm each and removing from site, complete all as specified and directed by Engr-in-charge.

Taking down steel windows including frames and shutters not exceeding 1.50 sqm each and removing to store, complete all as specified and directed by Engr-in-charge.

Taking down steel windows including frames and shutters exceeding 1.50 sqm but not exceeding 4 sqm each and removing to store, complete all as specified and directed by Engr-in-charge.

S&F 2nd class hard wood (sal/hollock), glazed and skelton shutters 35mm thick open rebated and prepared to receive glass, gauge,etc. (without sash bars), edges of framing palin, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I Section 8.24(a) supplied and fitted to chowkhats complete including fixing only iron mongery such as tower bolt,handle,hinges,aldrop bolt etc, complete all as specified and directed by Engr-in-charge.

S&F 35mm thick flush shutters, solid core construction, with particle board core and plywood face panels, with decorative face veneer on both faces withlipping/frame to match, complete all as specified and directed by Engr-in-charge.

Factory made solid PVC moulded door shutter ( with particle board core) of 30mm thick with 2 raised panel design with 2mm thick moulded PVC sheet on back face & 2mm coloured prelaminated PVC sheet on front face as specified in SSR Part II 2010 Sec 8 clause 8 B 1 to 8B 2.1, complete all as specified and directed by Engr-in-charge.

S&F steel window (box type) factory made with sidehung shutter including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer, complete all as specified and directed by Engr-in-charge. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 . ii) MS fillets, glazing wire gauge shall be measured and paid seprately.

Description all as per Ser item No 34.00 here in before but without glazing bar, complete all as specified and directed by Engr-in-charge. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 sheet 1/3 to 3/3. ii) MS fillets, glazing, wire gauge shall be measured and paid seprately.

Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2004), complete all as specified and directed by Engr-in-charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004), complete all as specified and directed by Engr-in-charge. Make: Rajshri or equivalent as approved.

Mild steel framed work such as grills, gratings with ends of bars shouldered or reveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar works, conforming to Fe-290, Gde E-165, complete all as specified and directed by Engr-in-charge.

S&F aluminum handles cast type, anodised, 150 mm size, complete all as specified and directed by Engr-in-charge.

S&F in repair stainless steel butt hinges medium weight 100 mm long, including fixing and welding to pressed steel/wooden door frame if required, complete all as specified and directed by Engr-in-charge.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long, complete all as specified and directed by Engr-in-charge.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed by Engr-in-charge.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed by Engr-in-charge.

Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame, complete all as specified and directed by Engr-in-charge.

Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and taring back side of frame, complete all as specified and directed by Engr-in-charge.

M&L for providing cement concrete 1:3:6 type C-0 using 12.5mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast, complete all as specified and directed by Engr-in-charge.

S&F of stainless steel wire clothcut to size, 0.36 mm nominal dia wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staple in repairs, complete all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including CM bedding but not backing, removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engr-in-charge.

M&L for Non skid coloured 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.36 sqm, digital, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15mm thick screed bed in CM 1:6, complete all as specified and directed by Engr-in-charge.

All as per Ser item No 49.00 here in before but on skirting over vertical surfaces & including 10 mm thick cement mortar 1:4 screed, set and jointed with grey cement slurry and pointed in grout of matching shade of tiles, complete all as specified and directed by Engr-in-charge.

Material & Labour for Vitrified digital double charge tiles 600x600x8-10 mm thick (square or rectangular polished in floors set and jointed with Balendura adhesive or equivalent as approved by GE and pointed in white cement mixed with colouring pigment to match the shade or colour of tiles laid over and including 15mm thick screed bed or bedding layer with CM 1:6, complete all as specified and directed by Engr-in-charge. Make : Marbonite [series-2] of M/s H R Johnsons or equivalent make as approved by GE

M & L for Granite (of any type) slabs 20mm thick machine cut, bedded and jointed with grey cement slurry as in flooring, staircase steps & risers etc. and pointed with white cement with admixture of pigment to match the shade granite stone including grinding and polishing over and including 15mm thick screed bed in Cement Mortar 1:4 in floors etc complete all as specified and directed by Engr-in-charge.

Glazed ceramic coloured tiles digital 300mm x 600mm x 7mm thick as in vertical/Dado surfaces such as skirting dado etc set and jointed in neat cement slurry, jointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed by Engr-in-charge. Make - Johnson/ Kajaria or make as approved by GE.

Glazed ceramic coloured tiles 150mm x 600mm x 7mm thick as in vertical/Dado surfaces such as skirting dado etc set and jointed in neat cement slurry, jointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed by Engr-in-charge. Make - Johnson/ Kajaria or make as approved by GE.

M&L for 100 mm thick cement concrete 1:2:4, type B2 (using 40mm graded agg) as in path etc finished even and smooth w/o using extra cement, complete all as specified and directed by Engr-in-charge.

M & L for 50mm thick Plain Cement Concrete 1:3:6, type C-2 (using 20mm graded crushed stone aggregate), finished even and smooth without using extra cement as in plinth protrection, complete all as specified and directed by Engr-in-charge.

Roughening surfaces of old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and directed by Engr-in-charge.

M&L for brushing neat cement slurry with 3.00kg of cement per sq.metre, complete all as specified and directed by Engr-in-charge.

Material and Labour for chequered ceramic tiles, coloured/designer, 12 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sq M but not exceeding 0.11 Sq M, conforming to IS 4457-2007, on floors, set over and including 15 mm thick screed bed in cement mortar (1: 4) and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour, complete all as specified and directed by Engr-in-charge. Make:- (Johnson 'Endura'/ Somany 'Durastone'/ Regency 'Duro')

Machine pressed precast concrete interlocking paver block 50% grey and 50% coloured, any shape and size, conforming to IS 15658-2006 of 60mm thickness, M-35 over and including 75mm thick PCC, type D-2, M-7.5(1:4:8) and 25mm thick sand cushion with grey cement and pigment, complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster including tiles of any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-charge.

Rendering 15mm thick in cement mortar 1:4 on fair faces of bricks work/concrete surface finished the surface even and smooth (without using extra cement) as on walls, complete all as specified and directed by Engr-in-charge. Notes :- Plaster shall be carried out upto any height in patches and contractor shall have no claim for height and scaffolding what so ever is required to complete the work.

Rendering 15mm thick in cement mortar 1:6 on fair faces of bricks work/concrete surface finished the surface even and smooth(without using extra cement) as on walls, complete all as specified and directed by Engr-in-charge. Notes :- Plaster shall be carried out upto any height in patches and contractor shall have no claim for height and scaffolding what so ever is required to complete the work.

M&L for applying two coat of oil bond distemper on walls after preparation of newly plastered surfaces over a coat of white primer, complete all as specified and directed by Engr-in-charge.

M&L for finishing walls with textured weather proof exterior paint of required shade (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm, complete all as specified and directed by Engr-in-charge. Make : Dulux Weather Shield Signature or equivalent of Asain Paints/Berger.

M & L two coat of cement base paint over a coat of alkali resistant priming paint over old plastered surfaces of wall including preparing surfaces after conplete removal of existing treatment upto 5-10 m height from ground level and at all locations as directed including , scaffolding, cleaning and curing etc, complete as directed by Engineer-in-charge.

Preparation of old plastered/unplastered wall surfaces and applying one coat of oil bound distemper (including wahsing, rubbing down and stopping of distempered and painted surfaces), complete all as specified and directed by Engr-in-charge.

Preparation of old plastered/unplastered wall surfaces and applying one coat of white wash, complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 15mm, complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 20mm, complete all as specified and directed by Engr-in-charge.

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm, complete all as specified and directed by Engr-in-charge.

Fixing only Steel water tubing 15mm dia medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors, complete all as specified and directed by Engr-in-charge.

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20 mm, complete all as specified and directed by Engr-in-charge.

Fixing only Steel water tubing 20mm dia medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors, complete all as specified and directed by Engr-in-charge.

S&F in repairs Rotational moulded polyethylene water storage tank 1000 Ltrs capacity, ISI marked (cylindrical vertical with closed top), triple layer construction, Pure Antimicrobial hoisted and fixed in position complete all as specified in SSR Part-I, making connections incl 20mm bore ball valve brass with polyethylene float and fly nut and tank nipples incl dismantling existing water tank of any capacity and removing from site, complete all as specified and directed by Engr-in-charge.

Supply and fixing in repair ball valves of size 15 mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site, complete all as specified and directed by Engr-in-charge.

Supply and fixing in repair angle valves cast copper alloy 15 mm, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site, complete all as specified and directed by Engr-in-charge. (Make Cat No QQT-7053 of Jaquar or equivalent of Ess Ess/ Kohler/Marc)

S&F in repair 15mm dia stop cock fancy type chromium plated, complete all as specified and directed by Engr-in-charge. (Make Cat No QQT-CHR-7083K of Jaquar or equivalent of Ess Ess/ Kohler/Marc)

S&F as in repair bib tap 15mm bore fancy type chromium plated, complete all as specified and directed by Engr-in-charge. (Make Cat No QQT-7037 of Jaquar or equivalent of Ess Ess/ Kohler/Marc)

S&F bib cock 15mm bore fancy type long body chromium plated in repair, complete all as specified and directed by Engr-in-charge. (Make Cat No ALI-CHR-85037 of Jaquar or equivalent of Ess Ess/ Kohler/Marc)

S & F in repair 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed by Engr-in-charge.

All as per Ser item No 81.00 here in before but dia 15mm, complete all as specified and directed by Engr-in-charge.

Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed by Engr-in-charge.

Precast reinforced cement concrete, (Nominal mix), Type B-1, 1:2:4 (using 20mm graded crushed stone aggregates) as in cover slab, manhole cover, shelves and similar articles with plain face, set and jointed in cement mortar 1:4, complete all as specified and directed by Engr-in-charge. (Note : Reinforcement shall be measured and paid separately)

TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for slabs,beam, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed by Engr-in-charge.

TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for slabs,beam hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed by Engr-in-charge.

Hacking out old broken glasses (any thickness, size, quality or description) from wooden frames or steel frames, glazed with putty or fixed with wooden beads, complete all as specified and directed by Engr-in-charge.

4 mm thick sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-charge.

S & F in repair 32 mm dia waste coupling of PTMT (half or full threaded) (minimum weigh 45 gms), complete all as specified and directed by Engr-in-charge.

10 litre capacity PVC, low level, valveless, syphonic action type flushing cistern, dual flush, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia PVC flushing pipe and 15 mm dia 450 mm long PVC connection with PTMT waste coupling (fixed in repair), complete all as specified and directed by Engr-in-charge.

PVC connection suitable for 15 mm pipe with PTMT nuts and washers for both ends of length 450 mm long, (fixed in repair), complete all as specified and directed by Engr-in-charge.

S&F in repir stainless steel grating doom 100mm dia with or without hole, complete all as specified and directed by Engr-in-charge.

S & F 110mm bore PVC (SWR) pipes signle socketed, in any length with rubber ring joints, laid in trenches or in floor inluding taking down existing old pipes, complete all as specified and directed by Engr-in-charge.

All as per Ser item No 94.00 here in before but bore of pipe 75mm, complete all as specified and directed by Engr-in-charge.

S & F 110mm bore PVC (SWR) pipes signle socketed, in any length with rubber ring joints, fixed in walls inluding taking down existing old pipes, complete all as specified and directed by Engr-in-charge.

S & F 75mm bore PVC (SWR) pipes signle socketed, in any length with rubber ring joints, fixed in walls inluding taking down existing old pipes, complete all as specified and directed by Engr-in-charge.

S&F for 110mm PVC (SWR) bends any radius, complete all as specified and directed by Engr-in-charge.

S&F for 75mm PVC (SWR) bends any radius, complete all as specified and directed by Engr-in-charge.

S&F for 75mm dia outlet PVC(SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed by Engr-in-charge.

S & F in repairs, 15mm dia pillar taps, single lever basin mixer without popup waste with 450mm long braided hoses, complete all as specified and directed by Engr-in-charge. Make- Hindware cat part no-10051BPM or Jaguar as approved by GE.

S & F in repair for Vitreous china wash down water closet pan pedestal pattern, white including connection to drain (or outgoing pipe) and to flushing pipe antisyphonage pipe and plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device including jet pressure, complete all as specified and directed by Engr-in-charge. Make- Hindware cat part no-92565(S-22) size 68x36x74.5cm or Jaguar as approved by GE.

Vitreous China urinals fixed in repairs, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushingcistern, trap and waste pipe, complete all as specified and directed by Engr-in-charge. Make - Hindware(starwhite) cat part No-96008 Size-28x34.5x69 cm or Jaguar as approved by GE.

Vitreous china, white, wash hand basin, flat back of size 550x400mm, white including MS brackets and pedestal pattern including cutting for and pinning including 32mm dia CP brass waste coupling and PVC waste pipe, fixed in repair, complete all as specified and directed by Engr-in-charge. Make:- CERA cat part No. S 2040105 for WHB & for pedestal cat part No.S 2090101, Jaquar- SLS-WHT-0611F for WHB and SLS-WHT-1510 for pedestal or Hindware approved make as approved by GE.

Vitreous china, Pastel, wash hand basin oval shape, counter sunk size 560x410mm including 32mm dia CP brss waste coupling and PVC waste pipe, fixed in repair, complete all as specified and directed by Engr-in-charge. Make:- Hindware cat part No. 10017 or equivalent of Jaguar/Kohlar approved make as approved by GE.

Repairs to existing steel rolling shutters without ball bearing by taking down top cover, anchoring rod, spring etc and providing new springs and anchoring rod, replacing the worn out strips, safety lever lock of shutters and welding of handle, hasp staple and other broken articles etc, greasing the spring, guide rail, shaft etc and making functional and errecting in position, including refixing of top cover/hood etc, and refixing in same opening and making good in CM 1:3/PCC to match the existing surface, opening n.exc. 10 sqm each and finally painting with two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-charge.

S&F Steel rolling shutter (curtain made of 1mm thick mild steel sheet) area exc. 5sqm each with ball bearing, as specified including top cover, anchoring rod, hasp and staple, guide chennels, strike plate etc and one shop coat of primer erected in position as indicated push pull or manual type ,thickness of laths 1mm ,incl taking down carefully existing old rolling shutter, complete all as specified and directed by Engr-in-charge.

Taking down the existing aluminium door/window frame with shutters exc.1.5 sqm each incl all accessories and making good the disturbed portion, complete all as specified and directed by Engr-in-charge.

M&L for Powder coated (of approved color) aluminium sliding window of any shade with frame of section 100mm x 45mm , thickness of sheet 16 gauge , including sliding shutter with shutter of section 32mm x 15mm (with and including Triple Track and 2 Nos Glazed Shutter and 01 No Gauzed Shutter) including Stainless Steel wire mesh, rubber gasket for securing the glass, 4 mm thick Tinted glass and necessary Aluminium moongreies and handles, locks complete all as specified and directed by Engr-in-charge.

M&L for Powder coated (of approved color) aluminium door frame of any shade with shutter of section 100mmx 45mm, thickness of sheet 3mm , partly panelled shutter and partly glazed lock rail / bottom rail of shutter 100mm x 45mm, top rail 80mm x 45mm including necessary jointing cleats, anodized aluminium including necessary fittings and aluminium mongeries i.e. 200mm long two Nos aluminium handles, 02 No, 200mm long aluminium tower bolt in each leaf, rubber gasket for securing the glass and 3 Nos 100 mm long butt hinges with each including 5 mm thick tinted glass and 12 mm thick Prelaminated Particle Board including mortice lock, hydraulic door closure to each shutter, complete all as specified and as directed by Engineer-in-charge.

S&F in repair Aluminium (Diecast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width & of weight between 61 to 80kg, complete all as specified and directed by Engineer-in-charge.

Providing and fixing 12 mm thick clear toughened glass door of area exc1 sqm but not exceeding 4.00 Sqm (saint-gobain or modiguard), MES logo, as per approved design, with making holes, cut-outs as required, making edges clear smooth polished, fixed with approved stainless steel Top & bottom Patch Fitting with necessary door assembly (pre installed hardware, removable clip on covers, end cap and rubber gasket for proper grip), U / F pattern rubber beeding on two vertical sides and fixed on double action floor spring with closing force as directed, having high grade cast mechanism body, housed within a corrosion resistant zinc paint protected galvanised steel loose box, internal mechanism components utilizing heat treated high alloy steel and ball bearing for optimum efficiency, closer mechanism totally immersed in hydraulic fluid, "hold open" models, having the possibility of the shutter being held open at 90 degrees angle, adjustable closing speed valve, with pivot to suit patch fittings and door shutters, having tempered full glass panel of upto 120 Kg weight, and Door handle both face : 550mm long x 25 mm diameter "S" type, SS Finish, back to back installation, glass damage preventing gasket, grub srews finish and Bottom Patch Lock Solid SS finish, complete all as specified and as directed by Engineer-in-charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and as directed by Engineer-in-charge.

S & F in repairs stainless steel curtain rod, surface finish No. 4 as per IS 6911: 1992, 25 mm dia, including fancy brackets and holders etc, complete all as specified and as directed by Engineer-in-charge.

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-charge.

M&L providing and fixing of false ceiling with powder coated exposed Gl grid suspension system (E-grid T-2420 or equivalent of Armstrong having load carrying capacity of 12.5 Kg/M3 with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200/600 mm long and Wall Angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall with steel screws with distance 300 mm c/c. The main runners to be placed @ 1200 mm, the cross tee 1200 mm will be inserted in the pre-cut slots of Main Runner at regular interval of 600 mm to form a modular grid of 1200x600mm. Additional cross tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm x 600 mm with and including 6 mm thick HSPC (High pressure steam cured) oceanic pre primed, self embossed, textured designer board, water, termite & fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4 mm dia GI wire hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt 0.007 kg/clip), hold down clips (wt-0.0035 Kg/clip), with provn of light fixture complete all as per manufacturer instructions, complete all as specified and as directed by Engineer-in-charge. Make: Armstrong/Everest

Supply & Fixing in repair ACP panel as in wall panelling or cladding 6 mm thick of required colour fixed on mild steel framing or grill of specified spacing fixed on face of walls or coloumn by drilling hole with screw & joints of panels shall be sealed with silicon tape as per manufacturer Instructions, complete all as specified and as directed by Engineer-in-charge.

Solid PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES schedule part-II, complete all as specified and as directed by Engineer-in-charge.

M&L18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws as in shelves, shutters etc ,including hinges,hasp staple, complete all as specified and as directed by Engineer-in-charge.

Providing and applying Polymer modified cement mortar of average thickness 15-20mm using Polymer in one or more layers in proportion 1:5:15 of Polymer Cement Quartz Sand as manufacturer’s specifications in specific layers, curing the surface after 72 hours of application with wet gunny bags etc and by finishing the surface with 12mm thick (1:3) Cement sand plaster, complete all as specified and as directed by Engineer-in-charge. Make :- SIKA - Sika 122 WL FOSROCK - Renderoc S2

Providing and applying Polymer modified cement mortar of average thickness 30-40mm using Polymer in two layers in proportion 1:5:15 of Polymer Cement Quartz Sand as manufacturer’s specifications in specific layers, curing the surface after 72 hours of application with wet gunny bags etc and by finishing the surface with 12mm thick (1:3) Cement sand plaster, complete all as specified and as directed by Engineer-in-charge. Make :- SIKA - Sika 122 HS FOSROCK - Renderoc HS xtra

M&L for preparation of old plastered or unplastered surfaces of wall and applying one coat of anti-fungal acrylic emulsion paint (Appex) any tinted, complete all as specified and directed by Engineer-in-charge.

Supply and fixing factory made uPVC white colourThree track three panels sliding window with fly proofS.S wire mesh (Two nos. glazed & one no. wire meshpanels) upto 1.50m height made of (big series) frame116 x 45 mm & sash 46 x 62 mm both having wallthickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Areaof window above 1.75 sqm) comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mmthick galvanized mild steel section made from rollforming process of required length (shape & sizeaccording to uPVC profile), appropriate dimensionof uPVC extruded glazing beads and uPVC extrudedinterlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy bodywith single nylon rollers (weight bearing capacity tobe 40 kg), G.I fasteners 100 x 8 mm size for fixingframe to finished wall and necessary stainless steelscrews etc. Profile of frame & sash shall be mitred cutand fusion welded at all corners, including drillingof holes for fixing hardware's and drainage of wateretc. After fixing frame the gap between frame andadjacent finished wall shall be filled with weatherproof silicon sealent over backer rod of required sizeand of approved quality, complete all as specified and directed by Engineer-in-charge. (Glass or wiremesh shall be paid separately)

Note: For uPVC frame and sash extruded profilesminus 5% tolerance in dimension i.e. in depth & widthof profile shall be acceptable. Variation in profiledimension in higher side shall be accepted but noextra payment on this account shall be made.

Supply and fixing factory made uPVC white colourfixed glazed ventilator made of (small series)frame 47 x 50 mm mullion 47 x 68 mm both havingwall thickness of 1.9 ± 0.2 mm and single glazingbead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame andmullion (where ever required) extruded profiles dulyreinforced with 1.60 ± 0.2 mm thick galvanized mildsteel section made from roll forming process ofrequired length (shape & size according to uPVCprofile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, G.I. fasteners 100 x 8 mmsize for fixing frame to finished wall, plastic packers,plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion weldedat all corners, mullion (if required) shall be also fusionwelded including drilling of holes for fixinghardware's and drainage of water etc. After fixingframe the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealantover backer rod of required size and of approvedquality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paidseparately). Note: For uPVC frame, sash and mullion extrudedprofiles minus 5% tolerance in dimension i.e. indepth & width of profile shall be acceptable.Variation in profile dimension in higher side shallbe accepted but no extra payment on this accountshall be made

Providing and fixing GI frame work including 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface sunk or raised moulding over metal frame work and reinforced with G.I. wire mesh including one coat of putty and two coats of paint, shades as approved by GE, complete all as specified and directed by Engr-in-Charge.

M&L for acrylic texture paint over a coat of base paint complete all as manufacturer instructions, shades, make and design to be approved by GE.(Make- Asian paints, Berger)

E/M PORTION Taking down carefully alu./copper point wiring ,light fan socket, or power complete with fittings such as switches ceiling rose;holders; regulators, socket etc removing material to store for keeping in safe custody for reuse or disposal by credit and marking good to disturbed surfaces of walls floors etc, complete all as specified and directed by Engineer-in-charge.

M & L for concealed point wiring with FRLS grade PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC concealed conduit for fixing of switches, sockets,light, fan regulators etc for the following, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Plaza

One light/fan/bell point or one fan point controlled by one switch

One 3/5 pin socket outlet, 5 Amp independent

One socket outlet 5 Pin, 5 Amps, SP on same board.

One socket outlet 6 pin 6/16 Amps, indipendent with cables 2.5 sqmm size .

One light point point controlled by two 2-way switches with cables 1.5 sqmm size.

M & L for wiring with FRLS grade PVC insulated unsheathed multistranded copper conductor cables in PVC casing caping of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm for fixing of switches, sockets,light, fan regulators etc for the following, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Plaza

One light/fan/ /bell point or one fan point controlled by one switch

One 3/5 pin socket outlet, 5 Amp independent

One socket outlet 5 Pin, 5 Amps, SP on same board.

One socket outlet 6 pin 6/16 Amps, indipendent with cables 2.5 sqmm size .

S&F Piano type switch one way 6 Amps , 240 Volt, ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F Bell push,flush type, one way 6 Amps , 240 Volt, ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F Switch Piano type single pole 15Amps one way 240 Volt, ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F Switch 6 amp, 2 way, 240 Volt ,ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F socket outlet 2 in 1,3/5 pin piano type 5 Amp flush type ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F socket out let 6 /16 Amps 6 pin flush type, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F Lamp holde PVC type with back plate suitable for batten fittings, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F of electronic step type regulator of capacity 240 volts flush type ISI marked, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S& F Bell Ding dong, AC, 230 volts, single pole, complete all as specified and directed by Engineer-in-charge. Make : Anchor/Havells/Legrand/Roma

S&F in replacement LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings, complete all as specified and directed by Engineer-in-charge. Make : Philips/Havells/Wipro

Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and directed by Engineer-in-charge. Make : Philips/Havells/Wipro

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engineer-in-charge. Make : Philips/Havells/Wipro

S&F in replacement LED light fitting 1 x 9 W/ 1 x 10 W Bulk head luminaires complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings, complete all as specified and directed by Engineer-in-charge. Make : Philips/Havells/Wipro

S&F in replacement of sub main wiring with copper conductor cable (2 runs of cable) multistaranded 4.0Sqmm PVC FRLS ISI marked with all insulated unsheathed in and including PVC concealed conduit 25mm dia medium grade fittings including 4.0 Sqmm copper conductor cable PVC FRLS insulated unsheathed multithreaded using as continues earth wire connected to common earth and earth dolly, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Plaza

S&F in replacement of sub main wiring with copper conductor cable (2 runs of cable) multistaranded 6.0 Sqmm PVC FRLS ISI marked with all insulated unsheathed in and including PVC concealed conduit 25mm dia medium grade fittings including 6.0 Sqmm copper conductor cable PVC FRLS insulated unsheathed multithreaded using as continues earth wire connected to common earth and earth dolly, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Plaza

M&L for earthing in repair complete with galvanized steel earth electrode 60cmX60cmx6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level ) with top edge of the plate not less than 1.5m below normal ground level connected to earth lead by means of bolts nuts and washers of GI steel and including earthing pit charcoal, common salt, GI 4.0mm dia lead wire 20mm GI medium grade watering pipe 15mm bore light grade protection pipe 5 Mtr length with wire mesh and funnel PCC pit in PCC 1:2:4 type B-1 using 20mm graded stone aggregate, angle iron frame and RCC cover and earth work complete all as shown in electrical plate No.3 of SSR -2009(Part-1), complete all as specified and directed by Engineer-in-charge.

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces, complete all as specified and directed by Engineer-in-charge. Make : Havells/Legrand/L&T

S&F Sheet metal enclosure factory made for DBs single pole and neutral single door 240 volts 12 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing, and commissioning and making good of wall, surfaces, complete all as specified and directed by Engineer-in-charge.

S&F Sheet metal enclosure factory made for DBs Triple pole and neutral single door 415 volts 12 way ,suitable for MCCBs and fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing, and commissioning and making good of wall, surfaces, complete all as specified and directed by Engineer-in-charge.

S&F RCBO double pole, 240 Volts , 50 Hz, 40 Amps, 30mA, complete all as specified and directed by Engineer-in-charge.

S&F MCB single pole and neutral, 240 Volts , 50 Hz, 40 Amps, complete all as specified and directed by Engineer-in-charge.

S&F MCB single pole 240 Volts , 6 to 20 Amps, complete all as specified and directed by Engineer-in-charge. Make : Havells/Legrand/L&T

Taking down ceiling fan sealing cable end etc and shifting to store complete and rehanging the same after overhauling and with white synthetic enamel paint(two coat) with the help of spray gun and connecting with three core flexible copper conductor cable 0.75 sq mm, complete all as specified and directed by Engineer-in-charge.

All as per Ser item No 154.00 here in before but for exhaust of any size/make, complete all as specified and directed by Engineer-in-charge.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm 2 core in service connections fixing with wall/ceiling properly, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Gloster

All as per Ser item No 156.00 here in before but for 10 sqmm 2 core, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Gloster

All as per Ser item No 156.00 here in before but for 16 sqmm 2 core, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Gloster

S& F in replacement MCCBs 415 Volt 16 KA, 4 pole 63 Amp, complete all as specified and directed by Engineer-in-charge. Make : Havells/Legrand/L&T

S& F in replacement XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm 4 core, complete all as specified and directed by Engineer-in-charge. Make : Havells/Polycab/Gloster

S& F in repair PVC Rectangular block for switches,socket, fan regulator, 3 mm thick plastic laminated sheet cover of size 100mm x 100 mm and 50 mm deep, complete all as specified and directed by Engineer-in-charge.

Checking,servicing, oiling and greasing of fan of any size/type by using appropriate grade of oil /grease and replacing defective parts such as bush, bearing, split pin, rubber bush, hanging clamp and capacitor etc including cleaning, complete all as specified and directed by Engineer-in-charge. (Note:-Parts/components will be measured and paid seperately under their respective items)

Rewinding of celling fan 1200/1400mm sweep, AC, 230 volts single phase with super enamelled copper winding wire of appropriate size including packing, insulating material, soldering, varnishing, reassembling and testing as required, making functional, complete all as specified and directed by Engineer-in-charge.

Nuts, bolts and washers of appropriate size for hanging of celling fan, complete all as specified and directed by Engineer-in-charge.

Top / botton canopy of required size with tightening screws, complete all as specified and directed by Engineer-in-charge.

Bearing of celling fans for 1200/1400mm sweep suitable for different makes /type of fans, complete all as specified and directed by Engineer-in-charge.

Ball bearing suitable for exhaust fan 300mm to 600 mm sweep of different make, complete all as specified and directed by Engineer-in-charge.

Split pins of galvanished iron 1/8" dia, 2" length, complete all as specified and directed by Engineer-in-charge.

Rewinding of exhaust fan 300mm sweep AC 230 volts single phase with super enameled copper wire of appropriate size including packing insulating material, soldering, varnishing , reassembling , testing and making functional, complete all as specified and directed by Engineer-in-charge.

All as per Ser item No 169.00 here in before but for 450 mm to 600 mm sweep, complete all as specified and directed by Engineer-in-charge.

Condenser/capacitor suitable for 230 volts singls phase celling fan 1200mm/1400 sweep of approved make and quilty of capacity 2.5 MFD, complete all as specified and directed by Engineer-in-charge. Make : Havells/Standard/Usha

All as per Ser item No 171.00 here in before but for 3.15 MFD, complete all as specified and directed by Engineer-in-charge. Make : Havells/Standard/Usha

All as per Ser item No 171.00 here in before but 4 MFD for Exhaust Fan, complete all as specified and directed by Engineer-in-charge. Make : Havells/Standard/Usha

All as per Ser item No 171.00 here in before but 6 MFD for Exhaust Fan, complete all as specified and directed by Engineer-in-charge. Make : Havells/Standard/Usha

Supply and fixing Acrylic sheet molded letters ( GARRISON ENGINEER (UTILITIES) ) of size 1' x 1' white in colour with good quality LED strip light including constant current electronic driver and making connnection with suitable size copper conductor multistranded FRLS wire, complete all as specified and directed by Engineer-in-charge. Make : Havells/Philips/Wipro

S&F wireless,waterproof door bell for office at over 120 meter range operating, complete all as specified and directed by Engineer-in-charge.

S&F LED Lamp 9 Watt suitable for lamp holder, complete all as specified and directed by Engineer-in-charge. Make : Havells/Philips/Wipro

S&F in repair decorative, wall mounting, brushed nickel finish fixture with acrylic diffuser suitable with 9 W LED lamp B22 base, complete all as specified and directed by Engineer-in-charge. Make : Havells/Philips/Wipro

S&F in repair slim surface mounted 12 watt LED panel with premium diffuser to ensure glare free & even light distribution, complete all as specified and directed by Engineer-in-charge. Make : Havells/Philips/Wipro

RAJ MOHD (BID ID -3172494)

RAMAN CONSTRUCTION CO (BID ID -3181116)