Loading…
Loading…
Tender Value
₹1.4 L
EMD Value
₹2,850
Closing Date
8 Jul 2026, 2:30 pm4d left
AS PER THE NIT
AS PER THE NIT
Repair and Renovation of the office at Finance Complex, Haft Chinar, Srinagar
2026_PWDJK_314379_1
NIT NO 40/RNB/RAJ OF 2026-27 DATED 02/07/2026
Open Tender
Civil Works
7 days
SRINAGAR
as per the nit
2 documents required · 2 mandatory
₹200
AS PER THE NIT
₹2,850
3 Jul 2026
3 Jul 2026
8 Jul 2026
3 Jul 2026
8 Jul 2026
3 Jul 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm diameter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of framework by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete. 75mm overall thickness partitions with 12.5 thick double skin fire rated Glass Reinforced Gypsum (GRG), plaster board confirming to IS : 2095 (Part 3) 1996 (Board with BIS Certification marks) | 23.79 | Sqm | - | - |
| 2 | Providing and fixing of PVC panelling 8mm thick of required shade and design and manufacture including carriage of materials upto site of work complete including 6mm plywood as jamps as per the directions of Engineer-in-charge. | 59.5 | Sqm | - | - |
| 3 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) For fixed portion Powder coated aluminum (minimum thickness of powder coated 50 microns) | 18.2 | Kg | - | - |
| 4 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. | 5.02 | Sqm | - | - |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.48 MB
BOQ_1017885.xls
BOQ • 0.28 MB
Download all tender documents and submit your bid