At GHY: Electrical work for extension of Running room(Electrical portion) & Construction of additional 60 bedded RCC Building Loco Running Room at LMG. (Electrical portion)

A-At GHY: Electrical work for extension of Running room

Supply, Installation, testing and commissioning of Outdoor Cast Resin Oil 1 Type11KV/433V 500 KVA transformer, (BIS Level-1 as per Amendment 4 ) 3Phase,50Hz, Dyn11, copper wound, Class A insulation associated with winding temperature indicator / controller, having cable termination on the HV & LV sidesand all accessories and conforming to IS 2026 part 11. Technical specification as per technical specification attached in tender document.

Construction of 4 pole structure by supply, erection, fixing of the following GI channel and angle clamp with pole by 50 x 5mm GI flat with 50 x 16 mm diameter bolt and nut including making of hole by drill as per requirement with anti climbing device shall be provided by GI Barbed wire along with 33 KV danger board of size 8 x6 showing the voltage grade ,skull symbol etc. (i)GI 2 Channel(100 x 50 x 50 x 6 x2200)mm=4 nos. conductor bracket (ii) GI Angle50x50x6x2200mm=8 nos.bracing (iii) GI Channel (75 x40 x 40 x 6 x 2200mm=2 nos.guard wire (iv) GI Angle50x50x6x3200mm=8 nos.cross bracing. All materials shall be hot dip galvanized as per relevant IS standards. Fabrication and erection shall be carried out as per approved drawing and direction of Engineer-in-Charge. All fasteners shall be galvanized. Work shall include all labour, tools, tackles and incidental charges required for completion.

Supply, erection and commissioning of 12 metre long GI Tubular Pole, Type 410 SP- 63, conforming to IS: 2713 - 1980 (latest amendment), complete with base plate and top cap.Pole Details-Overall Length: 12 Metres,Sectional Length: 5.8 m + 3.1 m + 3.1 m,Outside Diameter (Bottom to Top):193.7 mm,165.1 mm,139.7 mm,Sectional Thickness:4.85 mm,4.50 mm,4.50 mm. Material: Hot dip galvanized steel. Complete with suitable size base plate and top cap.Erection & Foundation:Excavation of pit to a depth equal to 1/5th of the total pole height (i.e., approx. 2.4 m).Providing and laying Cement Concrete (CC) foundation in ratio 1:2:4 (1 Cement : 2 Sand : 4 graded stone aggregate of 19 mm and down size).The CC block shall be 30 cm x 30 cm in cross- section, extending:From bottom of pole foundation Up to 30 cm above Ground Level (GL).Proper alignment, ramming, curing and finishing shall be done.Backfilling and compaction shall be carried out properly as per direction of Engineer-in-Charge

Erection of rail/tubular pole to 1/5 th of its height with a CC foundation from base block (30 cm x 30 cm x 15 cm), including digging & refilling of earth to a height of 30 cm above ground level in ratio 1:3:6 by cement sand & Chips 19 mm & down including excavation of earth .

Supply, installation , testing and commissioning of Triple pole Air- break Gang Operating air break off load disconnecting switch (GOS) 11 KV 400 Amp. complete with drop out fuses, 3 insulator triple pole each pole consists of galvanize steel base HT insulator as per BIS non ferrous knife and spring loaded contact arcing horn of adequate section to break magnetizing current of the transformer horizontal GI shaft/ pipe of adequate length for phase separator, adequate 5 length for operation from ground level and operation handle complete with locking arrangement in both OFF & ON position. All ferrous parts shall be hot dip galvanized and suitable for outdoor service conditions. Fuse shall be conforming to IS:9385 part-I/1979, GOS shall be conforming to IS: 9921 Part-I/1981&9921 Part III/1982.complete with operating rod , drop out fuse and locking arrangement etc. conforming to IS: 1811 1992 or latest including provision of mounting arrangement for GOS as req. The work includes supply, loading, unloading, erection on pole/structure, alignment, connection, testing and commissioning complete in all respects as per direction of Engineer-in-Charge at site.

Supply, installation, testing and commissioning of lightning arrestor thyrite type conforming to IS: 3070 - Part III/1993 (Latest Version) suitable for protecting 11 KV installation including connection with earth pit by 25 mm x 6 mm GI strip and with overhead by ACSR conductor. The lightning arrestor shall be complete with suitable mounting arrangement for pole/structure 6 installation. The item shall include connection to earth pit using 25 mm x 6 mm GI strip and connection to overhead line using suitable size ACSR conductor, including all necessary clamps, nuts, bolts and accessories required for complete installation.All ferrous parts shall be hot dip galvanized and suitable for outdoor service conditions.The scope includes supply, loading, unloading, erection, connection, testing and commissioning complete in all respects as per direction of Engineer-in-Charge at site.

Supply and erection of CC foundation in ratio 1:2:4 cement,sand and good quality chips of size 19 mm and down size at site, including mixing, laying, compacting, curing and finishing 7 complete as required.The work shall include all labour, materials, tools, tackles, centering/shuttering (if required), curing and incidental charges necessary for completion of foundation work. The concrete shall be laid to required size, shape and level as per site condition and as directed by the Engineer-in-Charge of Railway.Complete in all respects as per direction of Engineer-in-Charge at site.

Provision of Horizontal Directional Drilling (HDD) / Horizontal boring using suitable HDD machine for crossing of road/Railway track embankment, at a minimum distance of 6 metres from embankment Ground Level (GL) and at a depth of not less than 2 metres below Ground Level, 8 as required.The work shall include preparation of site, setting out, drilling of 200 mm diameter bore, insertion/placing of protective pipe for electric cable through contractor's own arrangement, alignment, pulling and necessary precautions to avoid damage to road/track structure.The item includes all labour, machinery, fuel, consumables, equipment, supervision and incidental charges required for completion of work, complete in all respects as per direction of Engineer-in-Charge at site.

Supply, laying, fitting and fixing of 200 mm diameter heavy duty Cast Iron (CI) pipe conforming to IS: 1536 (latest amendment)for protection of cable under track crossing/under road 9 crossing, including cutting, jointing, alignment and fixing in position.The work shall include all necessary accessories such as collars, sockets, lead/jute yarn or rubber gasket (as applicable), excavation (if required), backfilling, alignment and proper positioning of pipe for safe cable protection.The pipe shall be of approved quality and suitable for underground installation.Complete in all respects as per direction of Engineer-in-Charge at site.

Excavation of cable trench of size 1.0 metre depth x 0.5 metre width below Ground 10 Level (GL) in all types of soil, including dressing, leveling and preparation of trench bottom.The work shall include laying of armoured cable in the trench, providing sand cushioning, brick protection on top of cable, and refilling the trench with excavated soil in layers with proper ramming and compaction .The item also includes supply and fixing of suitable size crimping lugs for termination of armoured cable, proper jointing/termination, connection, testing and commissioning complete in all respects. All materials such as sand, bricks, lugs and other consumables shall be supplied by the contractor .Complete in all respects as per direction of Engineer-in-Charge at site.

Supply erection of reinforced cement concrete Cable Trench made of Cement Bricks with Cement plaster and the RCC Cover. The Cable trench should be in ratio 1:3:6 by cement,Sand 11 and Ships of size 19 mm.including digging of pit to 500mm and MS rod of Suitable size. The item includes supply of all materials, labour, reinforcement steel, shuttering, curing and all incidental works required for completion of cable trench.Complete in all respects as per direction of Engineer- in-Charge at site.

Supply, laying, fitting and commissioning of 110 mm (OD) diameter Double Wall Corrugated (DWC) HDPE pipe, PN-6.0 kg/cm², conforming to IS: 14930 (Part-II) - latest amendment, suitable for cable protection, laid partly over ground and partly underground.The work shall include 12 supply of pipe with all necessary accessories such as sockets, bends, couplers, end caps, reducers (if required), cutting, jointing, alignment and proper fixing in position.For underground portion, excavation (if required), laying at required depth, backfilling and compaction shall be carried out. For over ground portion, proper clamping/support arrangement shall be provided.The item includes all labour, materials, tools, tackles and incidental charges required for complete installation and commissioning. Complete in all respects as per direction of Engineer-in-Charge at site.

Supply and wiring of sub-main line with 2 x 2.5 sq.mm PVC insulated, unsheathed, 13 multi-stranded FRLS copper conductor cable, conforming to IS: 694 (latest amendment), laid through suitable size PVC concealed rigid conduit pipe.The work shall include providing and drawing of 1 x 1.0 sq.mm unsheathed copper conductor as earth continuity wire along with phase and neutral conductors.All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply and wiring of sub-main line with 2 x 4 sq.mm PVC insulated, unsheathed, 14 multi-stranded FRLS copper conductor cable, conforming to IS: 694/1990 (latest amendment), laid through suitable size PVC concealed rigid conduit pipe.The work shall include providing and drawing of 1 x 1.0 sq.mm unsheathed copper conductor as earth continuity wire along with phase and neutral conductors.All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply and wiring of sub-main line with 2 x 6 sq.mm PVC insulated, unsheathed, 15 multi-stranded FRLS copper conductor cable, conforming to IS: 694/1990 (latest amendment), laid through suitable size PVC concealed rigid conduit pipe.The work shall include providing and drawing of 1 x 1.0 sq.mm unsheathed copper conductor as earth continuity wire along with phase and neutral conductors.All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply, laying, testing and commissioning of 10 sq mm single core copper conductor 16 PVC insulated, FR/FRLS grade cable, 1100V grade, conforming to IS 694, drawn through concealed rigid PVC conduit in wall/ceiling including all accessories. All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply of materials and wiring of light point through concealed wiring by 1.5 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sq mm single core PVC insulated unsheathed flexible copper wire and modular type 6 amps controlling switch(with indicator type) to be provided on good 17 quality modular plate and frame of suitable sizes and mounting box of proper sizes.(i.e thickness of mounting boxes of 3 mm and inside width of box should be 50 mm). All other necessary accessories i.e PVC Tee, Bend etc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site colour of the surface. Make - Cable- Finolex, Havells, KEI, Polycab Casing & Capping/Conduit - Diamond, Presto Plast, Richa C/Rose & Switch - Crabtree, Anchor, Legrand.All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply of materials and wiring of fan point through concealed wiring by 1.5 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sqmm single core PVC insulated unsheathed flexible copper wire and modular type 6 amps controlling switch(with fan marking) and module type step fan regulator of 100 W to beprovided on good quality modular plate and frame ofsuitable sizes and mounting box of proper sizes.(i.ethickness of mounting boxes of 3 mm and inside width of boxshould be 50 mm). All othernecessary accessories i.e PVCTee, Bend etc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site colour of the surface.All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply, Wiring of concealed exhaust fan point by PVC insulated unsheathed and multi stranded FRLS Copper Cable 1.5sq.mm S/C confirming to IS - 694/1990 through suitable size (19 19 mm) of PVC Concealed rigid Conduit pipe of wall thickness 2mm including ceiling rose and 10 AX one way modular switch in 1/2 M concealed unbreakable GI modular box, 2 M cover plate etc. with 1sq. mm unsheathed copper cable as earth continuity wire. All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply of materials and wiring of 6 amps plug point through concealed wiring by 1.5 sqmm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sq mm single corePVC insulated unsheathed flexible copper wire and modular type 6 amps controlling switch (with indicator type) and 2 modular 20 6Amps 5 Pin universal socket to be provided on good quality modular plate and frame of suitable sizes and mounting box of proper sizes.(i.e thickness of mounting boxes of 3mm and inside width of box should be 50mm). All other necessary accessories i.e PVCTee, Bend etc will be supplied by contractor.After concealed if needed than the concealed portion will be painted by contractor as persite colour of the surface. All work shall be carried out as per direction of Engineer-in-Charge at site.

"Supply of materials and wiring of 16 amps plug point through concealed wiring by 4 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sq mm single core PVC insulated unsheathed 21 flexible copper wire and modular type 16 amps controlling switch(with indicator type) and 3 modular 16 Amps 6 Pin universal socket to be provided on good quality modular plate and frame of suitable sizes and mounting box of proper sizes. (i.e thickness of mounting boxes of 3 mm and inside width of box should be 50 mm). All other necessary accessories i.e PVC Tee, Bend etc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site colour of the surface. All work shall be carried out as per direction of Engineer-in-Charge at site.

Supply, fitting, fixing, connection & commissioning of 300 mm sweep heavy duty exhaust fan. All consumables regarding fixing arrangement will be supplied by the contractor as per the direction of engineer in charge at site.

Supply; Wiring of concealed exhaust/wall bracket fan point by PVC insulated 23 unsheathed and multi stranded FRLS Copper Cable 1.5sq.mm S/C confirming to IS - 694/1990 through suitable size (19 mm) of PVC Concealed rigid Conduit pipe of wall thickness 2mm including ceiling rose and 10 AX one way modular switch in 1/2 M concealed unbreakable GI modular box, 2 M cover plate etc. with 1sq. mm unsheathed copper cable as earth continuity wire.

Supply of materials and wiring of modular type mobile charging through concealed/surface wiring with mobile keeping tray by 1.5 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealedrigid conduit pipe with earth 24 continuity by 1 sq mm single core PVC insulated unsheathed flexible copper wire and modular type 6 amps controlling switch 3 no and 6/10 amp 5 pin modular socket 3 nos to be provided on good quality modular plate and frame of suitable sizes and mounting box of proper size (i.e. thickness of mounting boxes of 3 mm and inside width of box should be 50 mm).All other accessories i.e. PVC Tee, Bend etc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site color of the surface.

Supply, installation, testing and commissioning of 36 Watt LED recess mounting 2'x2' flat panel luminaire, suitable for installation in false ceiling and operation on 230V, 50Hz AC supply, complete with electronic constant current driver, high transmission diffuser, CRCA powder-coated housing/frame, heat sink, flexible copper conductor connecting cable, ceiling rose and all mounting 25 accessories, including connection to existing wiring and testing complete as required at site. Technical Parameters: (i) Rated Wattage: 36 W (ii) Luminous Flux: Minimum 3600 lumens (iii) Luminous Efficacy: 100 lm/W (iv) Power Factor: 0.95 (v) THD: 10% (vi) CRI: 80 (vii) CCT: 4000K / 6500K (as specified) (viii) Input Voltage: 140-270V AC (ix) Surge Protection: 2.5 kV (x) LED Life: Minimum 50,000 hours (L70) (xi) IP Rating: IP20 (indoor) (xii) Warranty: Minimum 2-3 years

Supply, fitting, fixing, connection and commissioning of 18/20 Watt LED indoor batten 26 fitting, complete set with LED tube, electronic driver, housing, end caps and all accessories, suitable for operation on 230V, 50Hz AC supply. The fitting shall be connected with 1.5 sq.mm FR PVC insulated flexible copper conductor wire drawn through PVC pipe/casing & capping as required at site, including connection to existing wiring, testing and commissioning complete as required.

Supply, erection, testing and commissioning of heavy-duty 400 mm sweep wall bracket fan, suitable for operation on single phase 230V, 50Hz AC supply, complete with motor, blades, mounting bracket, guard, regulator (electronic step type), necessary clamps, nuts, bolts, 27 foundation fasteners and allied minor engineering works including drilling, grouting and connection to existing wiring, complete as directed by Site Engineer. Technical Parameters: (i) Sweep: 400 mm (ii) Rated Voltage: 230V AC, Single Phase, 50 Hz (iii) Power Consumption: 75-90 Watts (iv) Speed: Minimum 1300 RPM (v) Air Delivery: Minimum 70-80 CMM (vi) Motor: Copper wound motor with thermal overload protection (vii) Bearing: Double ball bearing (viii) Body: Powder-coated metal body with heavy-duty mounting bracket (ix) Duty: Continuous rating (x) Warranty: Minimum 2 years

Supply, installation, testing and commissioning of 3 kW, 25 litres capacity, 5-Star rated storage type water heater (Geyser) suitable for operation on 230V, single phase, 50Hz AC supply, complete with inner tank, heating element, thermostat, safety valve, mounting bracket, inlet & outlet connections, necessary fasteners, connection to existing water line and electrical wiring including earthing, testing and commissioning complete as directed by Site Engineer. Technical 28 Parameters: 1.Capacity: 25 Litres 2.Rated Power: 3 kW 3.Voltage: 230V ±10%, Single Phase, 50 Hz 4.Energy Rating: 5 Star (as per BEE latest notification) 5.Inner Tank: Glass-lined / Porcelain enamel coated with corrosion protection 6.Heating Element: Copper / Incoloy heating element 7.Thermostat: Adjustable thermostat with automatic thermal cut-out 8.Safety: oMultifunction safety valve (pressure relief) oOverheat protection oDry heating protection 9.Working Pressure: Minimum 8 bar (suitable for multi-storey buildings) 10.Insulation: High density PUF insulation 11.IP Rating: Minimum IPX4 12.Warranty: •Inner Tank: Minimum 5 years •Heating Element: Minimum 2-3 years •Product: Minimum 2 years.

Supply and wiring of geyser point complete with 15/16 Amp socket outlet, 16 Amp DP MCB for overload and short circuit protection, suitable for 230V, single phase, 50Hz AC supply. The point shall be wired with 4 sq.mm single core PVC insulated FRLSH copper conductor flexible industrial unsheathed cable for phase and neutral, drawn through heavy duty PVC rigid concealed 29 conduit pipe including necessary accessories such as PVC bends, tees, junction boxes, saddles etc. The earth continuity conductor shall be 1 sq.mm single core PVC insulated unsheathed flexible copper wire drawn along with the circuit wiring. The work includes making necessary wall chases, fixing conduit, box, accessories, proper termination, connection to existing distribution board, testing and commissioning complete. The concealed portion after wiring shall be properly plastered and finished; if required, the surface shall be painted by the contractor to match the existing surface colour, complete as directed by Site Engineer.

Supply & wiring of RAC (Room Air Conditioner) point through suitable size (minimum 19 mm dia) heavy duty PVC concealed rigid conduit pipe, complete with wiring by 2 x 4 sq.mm PVC insulated, unsheathed, multi-stranded FRLS copper conductor cable for phase and neutral, drawn 30 through conduit on wall, including 1 x 1 sq.mm PVC insulated unsheathed copper conductor as earth continuity wire. The point shall be complete with 1 No. 25A motor starter switch, 1 No. 32A SP Miniature Circuit Breaker (MCB), C-curve, minimum 3kA breaking capacity, and 1 No. heavy duty 3- pin shuttered socket outlet (6-16A type as specified), housed in concealed unbreakable GI modular box with modular plate/cover, including all accessories such as bends, tees, junction boxes, saddles, fasteners etc.

Supply, fitting and fixing of 3 Watt concealed LED reading lamp, suitable for operation on 230V, 50Hz AC supply, complete with LED module, in-built driver, flexible neck (where applicable), housing, mounting box, necessary fasteners and accessories, including connection to 31 existing wiring, testing and commissioning complete as required at site. •Rated Wattage: 3 Watts •Input Voltage: 140-270V AC •Luminous Flux: Minimum 180-250 lumens •Luminous Efficacy: 80-100 lm/W •Power Factor: 0.90 •THD: 20% •CRI: 80 •CCT: 3000K (Warm White) / 4000K (Neutral White) as specified •Beam Angle: 30°-60° focused beam •Body: Powder-coated aluminium / die-cast housing •LED Life: Minimum 30,000-50,000 burning hours •IP Rating: IP20 (indoor use) •Warranty: Minimum 2 years

Supply, installation, testing and commissioning of 1200/1400 mm sweep decorative ceiling fan (as specified), BEE 5-Star rated, conforming to IS: 374 (latest amendment), complete with Brush Less Direct Current (BLDC) motor, suitable for operation on 230V, 50Hz, single phase AC supply, including 3 nos. aerodynamically designed blades, 30 cm down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, remote control/electronic regulator unit for speed control, safety pin, nuts, bolts, washers, earthing and all accessories, complete as required at site. Technical Specifications: 1.Sweep: 1200 mm / 1400 mm (as specified) 2.Standard: IS: 374 (latest amendment) & ISI marked 3.Energy Rating: BEE 5-Star rated 4.Motor Type: BLDC Motor 5.Input Voltage: 230V ±10%, 50 Hz, Single Phase 6.Power Factor: 0.90 7.Service Value: Minimum 6.00 (CM/M/W) 8.Air Delivery: Minimum 210 m³/min 9.Speed: Approx. 350 RPM (tolerance as per IS 374) 10.THD: 10% 11.Insulation Class: Class B 12.Temperature Rise: Maximum 75°C 13.Insulation Resistance: 2 Mega Ohm 14.Down Rod Length: 30 cm 15.Accessories: Shackle assembly, safety rope, canopy, remote/electronic regulator, complete fixing hardware 16.Warranty: Minimum 2-3 years

Supply and erection of copper plate earthing station comprising of 600 mm x 600 mm x 6 mm thick copper earth plate buried in ground at a minimum depth of 3.0 metres below ground level (or as per site condition), including construction of earth pit chamber with brick masonry, RCC/Precast concrete cover with CI frame and cover, watering arrangement with GI pipe and funnel with wire mesh, alternate layers of charcoal/coke and common salt, complete as required. The earthing arrangement shall include 40 mm x 5 mm copper flat of 15 metre length for earth 33 continuity conductor, securely connected to the earth plate with brass/copper nuts, bolts, washers etc., and extended up to the required equipment. The earthing terminal shall be connected to the neutral terminal of transformer and integrated with the system earthing network, complete as directed by Site Engineer. Technical Specifications Earth Plate: Copper plate 600 x 600 x 6 mm Depth of Burial: Minimum 3.0 m below ground level Earth Continuity Conductor: 40 x 5 mm copper flat, 15 m length Hardware: Brass/Copper nuts, bolts & washers Earth Pit Construction: Brick masonry chamber RCC/Precast concrete cover with CI frame Watering pipe with funnel & mesh Backfill Material: Charcoal/coke and salt in alternate layers Earth Resistance: Achieved value preferably 1 Ohm (or as specified) Testing: Earth resistance measurement using approved earth tester

Supply and erection of earthing by 50 mm GI pipe, 4 mtr long 3.6 mm thickness including construction of earth pit, RCC earth cover slab with filling/mixing of salt, charcoal etc of required quantity and earth continuity by 25x3mm GI strip with GI nuts bolts washer etc. including welding, earth resistance flag etc. as per Drg. No. DRG No. PCEE-ELG-DRG-2024-1-Rev-1 Dt. 28.07.2025. The GI Strip ( should be welded with the earth pipe. The pipe is provided with at tapered 34 casing at the lower end in order to facilitate the driving. A funnel with perforated plate to be provided at the top of the pipe for pouring water during dry season to have an effective earth value. The connecting conductor from earth electrode to the distribution panel board should not be thinner than8 SWG GI wire to carry the fault current. The earth fill shall be of homogeneous layer of common earth soil. Where soil restivity is high, earth restivity enhancing material may be used, Bentonite or similar earth enhancing material may be used in rocky soil. Earth box to be pre casted RCC and The values of earth resistance measured should be painted on the Earth pit cover/lid along with the date of measurement. Square

SUPPLY OF MATERIAL, INSTALLATION, TESTING & COMMISSIONING OF MULTICOLOR LED BASE NAME BOARD :(Technical specification / salient features for LED name board ) :- 1. Power supply System:- It should be as under. Input: 230 Volt single phase A.C ± 5% Output : 12 Volt D.C. 2. a) Letters for name board shall be made in three languages i.e. English, Hindi & Assamese . b) Substrate material used for the front portion of channel letter shall be 3 mm thick Acrylic sheet frosted or milk white (0/40). c) letter size should be as per board area and width of letter should be in proportionate to the height d) Depth of each letter should not be less than 3"" e) Back of letter 35 should be of sunpack sheet or 28 SWG powder coated sheet. f) Front & Back of letters should be assembled in such a fashion that it remains water tight, Dust proof. g) Front & Back of letters should be jointed / tighten with steel screw and washers, so that it may be opened in case of failure or for maintenance. h) All letters of each location should be fitted suitably on 3mm thick ALUMINUM PANEL Sheet and background shall be dark blue, if Required and this sheet to be fixed suitably on above M.S. Structure. i) Complete name board should be fixed on a M.S. Iron frame structure suitable size to withstand the atmospheric weather wind pressure etc. j)M.S. Structure should be grouted well with appropriated cement, concrete mixture at given Location. (Note1- LED Signage board are to be erected at various stations as per requirement and N.F.Railway will be also add in each borad at lower side, Location may be add or change as per instruction of competent authority )"

Supply, fitting, fixing, testing and commissioning of 10 kVA Online UPS, complete with necessary internal batteries (if specified), input-output MCBs, bypass arrangement, interconnecting cables, earthing, installation, testing and commissioning, complete in all respects and as directed by Engineer-in-Charge at site. Technical Specifications •Capacity: 10 kVA •Type: Online UPS (Double Conversion) •Input Supply: 230V AC Single Phase / 415V AC Three Phase (as required) •Output: 230V AC, 50Hz, Pure Sine Wave •Efficiency: 90% •Power Factor: 0.9 •Waveform: True Online Double Conversion •Static Bypass: Inbuilt automatic & manual bypass •Display: LCD / LED display for parameters •Protections: oOverload oShort circuit oBattery low oOver temperature oInput over/under voltage

Supply, fitting and fixing of 12V, 75Ah VRLA (Valve Regulated Lead Acid) battery for UPS, conforming to IS 16046, complete with interconnecting leads, terminal covers, necessary hardware, testing and commissioning, including two years onsite warranty, complete as required 37 and as directed by Engineer-in-Charge. Technical Specifications •Type: VRLA (SMF - Sealed Maintenance Free) •Rated Voltage: 12 Volts •Capacity: 75 Ah @ C10/C20 rate (as applicable) •Standard: IS 16046 •Design Life: Minimum 3-5 years •Container: ABS body, leak proof •Terminal Type: Heavy duty threaded terminal •Application: Suitable for UPS duty (High discharge rate) •Warranty: Minimum 2 years onsite replacement warranty

Supply, fitting, fixing, testing and commissioning of 3 Watt LED concealed foot light 38 fitting, complete with inbuilt LED lamp, driver, mounting accessories, internal wiring and all necessary hardware, suitable for operation on 230V AC supply, complete as required and as directed by Engineer-in-Charge.

Supply and installation of Single Phase Automatic Voltage Stabilizer suitable for 1.5 39 Ton Air Conditioner, with input voltage range 120V-280V and output voltage range 195V-245V (Single Phase Sine Wave), conforming to IS: 8448:1989 (latest amendment), complete with mounting arrangement, input-output wiring, testing and commissioning as required and as directed by Engineer-in-Charge.

Supply and fixing of MS Iron Angle base frame for outdoor AC unit, fabricated from 40 suitable size MS angle (minimum 40mm x 40mm x 5mm or as required), duly welded, drilled and painted with one coat of red oxide primer and two coats of synthetic enamel paint, including necessary anchor fasteners, foundation bolts, rubber pads, grouting and all fixing accessories, complete as required and as directed by Engineer-in-Charge at site.

Design, fabrication, supply, installation, testing and commissioning of LT Control Panel, outdoor type, double door, rear access, FORM-3b construction, suitable for 415V, 3 Phase, 4 Wire, 50Hz system, complete with MCCBs, changeover switch, busbar system, metering, protection, cable alley, internal wiring and all accessories as specified, complete in all respects. Technical Specifications 1. Standards & Compliance IEC 60439-1 / IS 8623 Part-1 IEC 60947-2 (for MCCBs) IS 694 (Control wiring) CPRI type tested & ISI / ISO approved manufacturer Short circuit withstand capacity: 100 kA for 1 second Temperature rise test at 6300A as per IS 8623 Part-1 2. Panel Construction •Outdoor type, rear access, FORM-3b •Protection: IP54 / IP55 •Colour: RAL 7035 structured finish •CRCA steel enclosure oLoad bearing parts: 2.0 mm thick oNon-load bearing parts: 1.6 mm thick •Gland plate: 3 mm thick GI •Neoprene gasketed doors •Cable entry: Incoming - 41 Bottom / Outgoing - Bottom •Separate cable alley provided •Built & inspected at OEM factory in presence of Railway representative •Approved drawings to be submitted before fabrication 3.Busbar System •Horizontal busbar at top throughout panel •TPN electrolytic grade copper busbar •Size: 50 mm x 6 mm (R, Y, B & N) •Heat shrinkable colour coded PVC sleeves •Mounted on porcelain insulators with adequate clearance •Incoming switches connected to busbar through crimped sockets •Separate earth busbar provided 4. Incomer & Outgoing Configuration (i) Incomer •630A, 4 Pole MCCB, 50kA, adjustable thermal magnetic - 1 No. •800A, 4 Pole On-Load Changeover Switch (Manual Transfer Switch) - 1 No. (ii) Outgoings •400A, 4 Pole MCCB, 50kA - 4 Nos. •250A, 4 Pole MCCB, 36kA, Ics = 100% Icu - 2 Nos. •100A, 4 Pole MCCB, 25kA, Ics = 100% Icu - 2 Nos. All MCCBs shall conform to IEC 60947-2 with adjustable thermal magnetic settings. 5. Metering & Accessories •Multifunction meter (Digital) •CTs of suitable ratio •LED indicating lamps (RYB) •Auxiliary contactors •Selector switches / Cam switches •6A Control MCB •1.1 kV grade flexible copper control wiring •Terminal blocks with ferruling

Design, fabrication, supply, erection, testing and commissioning of floor mounted, outdoor type, double door LT Main Control Panel (8 Way MCCB Panel) complete with MCCBs, copper busbar, metering, protection, internal wiring and all accessories, conforming to IEC 60947-2, suitable for 415V, 50Hz, 3 phase, 4 wire AC supply, complete as required and as directed at site. Confirm outdoor IP rating (IP54/IP55 preferable). Ensure proper earthing & earth continuity bar. Conduct IR 42 test, functional test & primary injection test before commissioning. Panel Configuration Incomer 400A, 4 Pole MCCB, 50kA Ics, Ics = 100% Icu, adjustable thermal-magnetic type - 01 No. Outgoings 250A, 4 Pole MCCB, 36kA Ics, Ics = 100% Icu - 03 Nos. 100A, 4 Pole MCCB, 25kA Ics, Ics = 100% Icu - 04 Nos. All MCCBs shall conform to IEC 60947-2. Technical Specifications Panel Construction •Floor mounted, outdoor type, double door •Fabricated from 2 mm thick CRCA sheet steel •Powder coated finish •Dust & vermin proof construction (minimum IP54 recommended for outdoor) •Gland plate at bottom •Removable side covers •Adequate ventilation •Built & inspected at OEM factory in presence of Railway representative •Approved drawings to be submitted before fabrication Busbar •630A rated copper busbar •Electrolytic grade copper •Size: 50 mm x 6 mm (for R, Y, B & Neutral) •Proper colour coding & heat shrink sleeves •Suitable earth busbar Metering & Indications •Digital / analog Ammeter with selector switch •Voltmeter with selector switch •LED indication lamps (RYB) •6A SP control MCB •CTs of suitable ratio for ammeter & protection •Reverse current relay (if specified for DG/parallel application) Accessories Included •MCCB door interlocks •Auxiliary contacts •Spreader links •Terminal blocks (adequate size & quantity) •Ferruled internal wiring with PVC insulated copper wire conforming to IS 694 •Proper earthing terminals Standards •IEC 60947-2 - MCCB •IS 694 - PVC insulated copper wiring •Panel to be manufactured by CPRI approved panel manufacturer

Supply, fixing, testing and commissioning of 8 Way TPN Distribution Board (8+8+8 outgoing modules), conforming to IS 8623 (Part-1 & 3) / IEC 61439 (Part-1 & 3), fabricated out of CRCA sheet steel, RAL 9003 powder coated finish, single door, IK-08 mechanical protection, IP43 protection class, complete with busbar, neutral link, earth bar, DIN rail mounting, internal wiring and all accessories, suitable for 415V, 50Hz, 3 phase, 4 wire AC supply, complete as required at site. 43 Components Included The TPN DB shall be complete with the following MCBs (C-curve, 10kA breaking capacity or as specified): 63A, 4P MCB, C-curve - 2 Nos. 32A, DP MCB, C-curve - 2 Nos. 16A, DP MCB, C-curve - 4 Nos. 10A, SP MCB, C-curve - 4 Nos. Technical Specifications Enclosure: CRCA sheet steel, powder coated RAL 9003 Ingress Protection: IP43 Mechanical Protection: IK08 Busbar: Tinned copper busbar of suitable rating Neutral Link: Copper neutral bar with adequate terminals Earth Bar: Copper earth bar with suitable terminals Mounting: Surface/flush mounting (as specified) Internal Wiring: FRLS copper wiring with proper ferruling Standards: IS 8623 / IEC 61439

Supply, fixing, testing and commissioning of HT heat shrinkable type outdoor cable end termination kit, suitable for single core 11 kV grade, 120 sq.mm XLPE insulated, armoured aluminium conductor cable, complete with all accessories for terminating 11 kV cable to overhead line through suitable PG clamp, complete as required and as directed by Site Engineer. Technical Specifications Voltage Grade: 11 kV (12 kV class) Cable Type: Single core, 120 sq.mm, XLPE 44 insulated, armoured aluminium conductor Termination Type: Heat shrinkable, outdoor type Standard: Conforming to relevant IS/IEC standards for 11 kV cable accessories Kit Contents: Heat shrinkable stress control tubing Anti-tracking outdoor insulation tube Breakout boots Lugs (aluminium/compression type) Earthing accessories for armour Mastic tape, sealants and insulating materials PG Clamp: Suitable size for conductor and overhead connection Installation: Including stripping, crimping with hydraulic crimping tool, armour earthing, heat shrinking and proper dressing Testing: IR test and HV test (if required) after termination

Supply and laying of 50 mm dia medium class GI pipe, conforming to relevant IS 45 specification, laid in ground/on surface/wall (as specified), including cutting, threading, jointing with sockets, bends, tees, unions, necessary fittings, clamps, supports, excavation (if laid underground), refilling, testing and commissioning complete as directed by Site Engineer.

Laying, installation, testing and commissioning of LT/HT XLPE insulated, armoured aluminium conductor power cable of different sizes, partly laid along pole/structure and partly laid 46 underground through excavated cable trench, complete as required at site. The work includes loading, unloading and carrying of Railway-supplied cable to actual work site by contractor's own arrangement, straightening, dressing, clamping on pole with suitable saddles/clamps, laying in trench, sand cushioning, protective covering with bricks/tiles, backfilling, compaction, route marking, and testing before and after laying, complete as directed by Engineer-in-Charge.

Supply of 6 metre long single longitudinal welded, single dip hot-dip galvanized octagonal pole (Type: BOP-6030) having 70 mm top diameter, 130 mm bottom diameter and 3 mm steel thickness, manufactured under ISO 9001 & ISO 14001 certified facility, complete with base plate of size 220 mm x 220 mm x 12 mm thick, pole cap on top, and all necessary accessories. The work includes design, supply and construction of CC foundation, including excavation, PCC/RCC foundation as per design, backfilling and compaction; providing and fixing 4 Nos. anchor foundation bolts of 20 mm dia and 600 mm length (one set) embedded in CC foundation; provision of 6A SP MCB inside pole base compartment; fixing of Bakelite sheet terminals; and wiring with 2 x 1.5 sq.mm copper conductor cable from MCB to street light luminaire, complete as directed by Site Engineer. Technical Specifications Pole Type: Octagonal, single longitudinal welded Height: 6 metres above ground level Top Dia: 70 mm Bottom Dia: 130 mm Thickness: 3 mm Galvanization: Single dip hot-dip galvanized (minimum 70-80 microns coating) Base Plate: 220 x 220 x 12 mm Anchor Bolts: 4 Nos., 20 mm dia x 600 mm length with nuts & washers Foundation: CC foundation (size as per soil condition, typically 1:2:4 mix or as designed) MCB: 6A SP MCB inside pole box Internal Wiring: 2 x 1.5 sq.mm copper conductor cable Terminal Plate: Bakelite sheet with suitable connectors Includes: Excavation, concreting, curing, backfilling and erection

Supply & erection, fixing of MS Hot Dip Galvanized single arm bracket, 1000 mm long arm made of MS pipe having outer diameter 48.3 mm and wall thickness 3.25 mm, suitable for 48 mounting LED street light luminaire on 6 metre octagonal pole. The bracket shall be complete with suitable mounting pipe/clamp arrangement to fit on pole top, including necessary nuts, bolts, washers, GI fasteners, provision for cable entry and proper alignment, complete as directed by Site Engineer..

"Supply, installation, testing & commissioning of 45 wattoutdoor LED street light luminaire with heat resistantglass with connecting lead (IP protection- IP 66 class-I,System efficacy>=105 lm/w, Supply, installation, testing and commissioning of 45 Watt outdoor LED street light luminaire, suitable for operation on 230V, 50Hz AC supply, complete with pressure die-cast aluminium powder coated housing, heat resistant toughened glass cover, LED module, in-built driver, connecting lead and mounting arrangement, conforming to IP66 protection (Class-I), 49 complete as required and as directed by Engineer-in-Charge at site. The luminaire shall provide adequate illumination ensuring proper visibility at night including for persons with low vision. Technical Specifications Rated Wattage: 45 Watts System Efficacy: 105 lumens/Watt Luminaire Output: Minimum 4700-5000 lumens Input Voltage: 140-270V AC Power Factor: 0.95 THD: 10% Surge Protection: Minimum 5 kV (internal SPD) IP Rating: IP66 Electrical Class: Class-I Housing: Pressure die-cast aluminium with powder coating Cover: Toughened heat-resistant glass LED Life: Minimum 50,000 burning hours (L70) CCT: 4000K (Neutral White) preferred for road visibility CRI: 70 Operating Temperature: Suitable for -10°C to +50°C Warranty: Minimum 3-5 years

Supply and fitting of 0.5 Watt LED bulb, suitable for operation on 230V, 50Hz AC supply, complete with LED lamp, inbuilt driver, B22/E27 cap (as specified), and connection to existing holder, including testing and commissioning complete as required at site.

B-Construction of additional 60 bedded RCC Building Loco Running

Supply, installation, testing and commissioning of 8 Way LT Outdoor Cubical Panel Board, dust, vermin and rodent proof, weather proof, chemically treated and dry powder coated, rain-shed type, floor mounted, double door construction, fabricated from 2 mm thick CRCA sheet steel on suitable MS channel/angle frame, complete with 400A, 4 pole electrolytic grade copper busbar, cable alleys, metering module, locking arrangement and all internal connections, complete as required and as directed by Engineer-in-Charge at site. 1. Panel Construction Type: Outdoor, Rain- shed type,Mounting: Floor mounted Construction: Double door cubical panel,Enclosure: 2 mm thick CRCA sheet steel,Frame: Suitable MS channel/angle frame Surface Treatment:Chemical treatment,Dry powder coated finish,Protection: Dust proof, vermin proof, rodent proof, weather 1 proof (Minimum IP54 recommended),Lockable door with proper locking arrangement. 2.Busbar System:Rating: 400A, 4 Pole (TPN),Material: Electrolytic grade copper,Adequate clearance between phases and earth,Heat shrinkable colour coded insulation sleeves,Properly supported on SMC/Porcelain insulators.3. Internal Wiring & Cable Management Internal connections using suitable size copper bus strip/copper cable ,Proper ferruling & dressing, Separate cable alleys for incoming & outgoing cables,Removable gland plates,Adequate earthing bar provided.4. Metering Module:Digital multifunction meter / Ammeter & Voltmeter (as required),CTs of suitable ratio,LED indication lamps (RYB),Selector switches,5. General Requirements:All hardware shall be zinc plated,All joints properly tightened,Proper earthing arrangement,Panel drawing to be submitted and approved before fabrication,Routine testing, IR testing and functional testing before commissioning. The panel comprising of the following item no 2,3,4,5,6 of schedule B.

Supply and installation of 400 Amps, 4 Pole MCCB, 50kA breaking capacity, Ics = 2 100% Icu, with adjustable thermal-magnetic release, conforming to IS: 13947 (Part-II) / IEC 60947-2, complete with necessary mounting hardware, interconnections, testing and commissioning, suitable for installation in Panel under Item No. 1 of Schedule-B, as required and as directed by Engineer-in- Charge.

Supply and installation of 250 Amps, 4 Pole MCCB, 36kA breaking capacity, Ics = 3 100% Icu, with adjustable thermal-magnetic release, conforming to IS: 13947 (Part-II) / IEC 60947-2, complete with necessary mounting hardware, interconnections, testing and commissioning, suitable for installation in Panel under Item No. 1 of Schedule-B, as required and as directed by Engineer-in- Charge.

Supply and erection of 100 Amps, 4 Pole MCCB, 25kA breaking capacity, Ics = 100% 4 Icu, conforming to IEC 60947-2, complete with adjustable thermal-magnetic release, necessary mounting hardware, interconnections, testing and commissioning, suitable for installation in Panel under Item No. 1 of Schedule-B, as required and as directed by Engineer-in-Charge.

Supply and erection of 63 Amps, 4 Pole MCCB, 25kA breaking capacity, Ics = 100% 5 Icu, conforming to IEC 60947-2, with adjustable thermal-magnetic release, complete with necessary mounting accessories, interconnections, testing and commissioning, suitable for installation in Panel under Item No. 1 of Schedule-B, as required and as directed by Engineer-in-Charge.

Supply & erection of pre-wired digital Metering Module comprising of Digital Voltmeter, Digital Ammeter, Voltmeter Selector Switch, Ammeter Selector Switch, suitably rated 6 Current Transformers (CTs), control fuses, LED indicating lamps (RYB), complete internal wiring with ferruled copper conductors, terminal blocks, mounting hardware, testing and commissioning, suitable for installation in Panel under Item No. 1 of Schedule-B, as required and as directed by Engineer-in-Charge.

Fabrication, design, supply, erection, testing & commissioning of Vertical 4 Way TPN Distribution Board, with MCCB incomer and (4+4+4) outgoing modules, IP-43 Outdoor type, conforming to IEC 61439-3, suitable for flush and surface mounting, complete with busbars, neutral bar, earth bar, gland plates, cable management accessories and all internal wiring, as required and 7 as directed by Engineer-in-Charge. Technical Specifications General •Type: Vertical 4 Way TPN DB •Protection: IP-43 (Outdoor Type) •Standard: IEC 61439-3 •Mounting: Suitable for Flush & Surface mounting •Enclosure: CRCA sheet steel, powder coated Incomer •MCCB Incomer (rating as per load requirement) •Adjustable thermal-magnetic release •Conforming to IEC 60947-2 Outgoing •(4+4+4) modular outgoing configuration •Suitable rating MCBs/MCCBs as per load distribution Busbars •Tinned electrolytic grade copper insulated busbars •Fully shrouded •Busbar rating selected as per distribution load •Neutral bar - fully shrouded with earth link •Earth bar - suitable capacity

Supply & erection of 125 Amps, 4-pole MCCB, 25kA breaking capacity, Ics = 100% 8 Icu, with adjustable thermal-magnetic release, conforming to IEC 60947-2, complete with necessary mounting hardware, interconnections, testing and commissioning, suitable to be fitted on DB under Item No. 7 of Schedule-B, as required and as directed by Engineer-in-Charge.

Supply & erection of 10-32 A, Double Pole (DP) MCB, C-Curve, conforming to IS/IEC 9 60947-2, complete with necessary mounting, interconnections, testing and commissioning, suitable to be fitted on DB under Item No. 7 of Schedule-B, as required and as directed by Engineer-in- Charge.

Fabrication, design, supply, erection, testing & commissioning of Vertical 12 Way SPN Distribution Board, IP-43 Outdoor type, conforming to IEC 61439-3, suitable for flush and surface mounting, complete with busbars, neutral bar, earth bar, cable management accessories, gland 10 plates, knockouts, and all internal wiring, as required and as directed by Engineer-in-Charge. Technical Specifications General •Type: Vertical 12 Way SPN Distribution Board •Protection: IP-43 (Outdoor Type) •Standard: IEC 61439-3 •Mounting: Flush & Surface mountable •Enclosure: CRCA sheet steel, powder coated, corrosion resistant Busbar System •Tinned electrolytic grade copper insulated busbars •Fully shrouded neutral busbar •Earth busbar with link connection •Busbar rating selected as per distribution load •Prefitted masking sheet

Supply & erection of 10-32 A, Double Pole (DP) MCB, C-Curve, conforming to IS/IEC 11 60898-2, complete with necessary mounting, interconnections, testing and commissioning, suitable to be fitted on DB under Item No. 10 of Schedule-B, as required and as directed by Engineer-in- Charge.

Supply & erection of 10 A, Single Pole (SP) MCB, B-Curve, conforming to IS/IEC 60898- 2, complete with necessary mounting, interconnections, testing and commissioning, suitable to be fitted on DB under Item No. 10 of Schedule-B, as required and as directed by Engineer-in-Charge.

Supply and wiring of main line (concealed type) using 1.1 kV grade HRFR PVC 13 insulated single core, 10 mm² multistrand flexible copper conductor cable, conforming to IS:694/1990, laid through 25 mm dia PVC conduit pipe, including provision of earth continuity using 1.1 kV HRFR PVC insulated single core 10 mm² multistrand flexible copper conductor, complete as per site requirement and as directed by Engineer-in-Charge.

Supply and drawing of Sub Main Line using single-core 6 mm² PVC insulated 14 unsheathed FRLSH flexible copper conductor, with earth continuity by 16 SWG bare copper wire, through good quality hard PVC casing/conduit, fixed on wall/ceiling with MS screws (6x40 mm) at intervals not exceeding 300 mm. One running meter (RM) consists of 2 wires, complete as per site requirement and as directed by Engineer-in-Charge.

Supply of materials and wiring of light point through concealed wiring by 1.5 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sq mm single core PVC insulated unsheathed flexible copper wire and modular type 6 amps controlling switch(with indicator type) to be provided on good 15 quality modular plate and frame of suitable sizes and mounting box of proper sizes.(i.e thickness of mounting boxes of 3 mm and inside width of box should be 50 mm). All other necessary accessories i.e PVC Tee, Bend etc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site colour of the surface. Make - Cable- Finolex, Havells, KEI, Polycab Casing & Capping/Conduit - Diamond, Presto Plast, Richa C/Rose & Switch - Crabtree, Anchor, Legrand.

Supply of materials and wiring of fan point through concealed wiring by 1.5 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sqmm single core PVC insulated unsheathed flexible 16 copper wire and modular type 6 amps controlling switch(with fan marking) and module type step fan regulator of 100 W to beprovided on good quality modular plate and frame ofsuitable sizes and mounting box of proper sizes.(i.ethickness of mounting boxes of 3 mm and inside width of boxshould be 50 mm). All othernecessary accessories i.e PVCTee, Bend etc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site colour ofthe surface.

Supply of materials and wiringof 16 amps plug point through concealed wiring by 4 sq mm single core PVC insulated flexible industrial unsheathed FRLSH copper wire throughPVC concealed rigid conduit pipe with earth continuity by 1sq mm single core PVC insulated unsheathed 17 flexible copper wire and modular type16 amps controlling switch(with indicator type) and3 modular 16 Amps 6 Pin universal socket to be provided on good quality modular plate and frame of suitable sizes and mounting box of proper sizes.(i.e thickness of mountingboxes of 3 mm and inside width of box should be 50mm). All other necessary accessories i.e PVC Tee, Bendetc will be supplied by contractor. After concealed if needed than the concealed portion will be painted by contractor as per site colour of the surface.

Supply of materials and wiring of 6 amps plug point through concealed wiring by 1.5 sqmm single core PVC insulated flexible industrial unsheathed FRLSH copper wire through PVC concealed rigid conduit pipe with earth continuity by 1 sq mm single corePVC insulated unsheathed 18 flexible copper wire and modular type 6 amps controlling switch (with indicator type) and 2 modular 6Amps 5 Pin universal socket to be provided on good quality modular plate and frame of suitable sizes and mounting box of proper sizes.(i.e thickness of mounting boxes of 3mm and inside width of box should be 50mm). All other necessary accessories i.e PVCTee, Bend etc will be supplied by contractor.After concealed if needed than the concealed portion will be painted by contractor as persite colour of the surface.

Supply and fixing of indoor type Wall LED Reading Light, 2 W, suitable for 220-240 V, 50 Hz AC supply, complete with all accessories, mounting arrangement, and as per IS standards as per direction of Engineer-in-Charge at site. Technical Specifications •Power Rating: 2 W •LED Type / 19 Make: Edison / Cree / Stanley Electric or equivalent •Input Supply: 220-240 V, 50 Hz AC •Color Temperature: 3000-6500 K (as per site requirement) •Material: Durable ABS / Aluminium body with diffuser •Mounting Type: Wall mount, indoor •Protection: As per IS standards (dust & vermin proof not required for indoor reading light) •Accessories: Necessary screws, brackets, holders, connectors for installation

Supply & wiring of RAC point through suitable size (19 mm) PVC concealed rigid 20 conduit pipe, with 2x4 mm² PVC insulated unsheathed multi-stranded FRLS copper cable on wall, complete with: 1 No. 25 A motor starter switch, 1 No. 32 A SP mini MCB (C-series, 3 kA), 6-16 A 3-pin shuttered socket with 3M concealed unbreakable GI modular box and cover plate, including 1 mm² unsheathed copper cable for earth continuity, as required at site and as directed by Engineer-in- Charge.

Supply, fitting and fixing of outdoor stand for RAC (Split AC) unit, suitable for 1.0-2.0 21 Ton capacity, fabricated from MS angle / MS channel, hot dip galvanized or powder-coated for corrosion resistance, complete with suitable mounting bolts, nuts, washers, vibration pads, and as required at site, including leveling, grouting, and fixing on wall/floor as per Engineer-in-Charge.

Supply, installation, fitting & commissioning of 5 KVA voltage stabilizer suitable for 1.5 / 2 Ton Split AC, single-phase 220-240 V AC supply, complete with all necessary accessories, protection devices, mounting arrangement, cabling, and as required at site, as directed by Engineer- 22 in-Charge. Technical Specifications •Capacity: 5 KVA •Input Voltage Range: 160-280 V AC (or as per stabilizer make) •Output Voltage Range: 195-245 V AC •Phase: Single-phase, 50 Hz •Protection: Overload, short-circuit, surge protection, thermal cutoff •Cooling: Natural / Fan cooled as per design •Mounting: Wall / floor mount suitable for indoor installation •Accessories: Input / output terminals, protection fuses, indicator lamps, stabilizer cover •Standards: IS:8448 (latest), ISI marked / equivalent

Supply, fitting, fixing, connection, commissioning, and wiring of Double Pole (DP) 30 mA RCCB, 40 A, including all required accessories such as terminals, screws, washers, and enclosures, complete as per IS standards and as directed by Engineer-in-Charge at site. Technical 23 Specifications •Type: Double Pole (DP) RCCB •Rated Current: 40 A •Residual Current Rating (Sensitivity): 30 mA •Poles: 2P •Breaking Capacity: Suitable to coordinate with connected load / MCBs •Standard: IS 12640 / IEC 61008 •Operating Voltage: 230/415 V AC, 50 Hz •Trip Function: Residual current / earth leakage protection •Accessories: Mounting terminals, screws, washers, cover / enclosure •Mounting: Flush or surface mounting as per DB arrangement

Supply, fitting, fixing, connection, commissioning, and wiring of Double Pole (DP) 100 mA RCCB, 100 A, including all required accessories such as terminals, screws, washers, and enclosures, complete as per IS/IEC standards and as directed by Engineer-in-Charge at site. 24 Technical Specifications •Type: Double Pole (DP) RCCB •Rated Current: 100 A •Residual Current Rating (Sensitivity): 100 mA •Poles: 2P •Breaking Capacity: Suitable to coordinate with connected load / MCBs •Standard: IS 12640 / IEC 61008 •Operating Voltage: 230/415 V AC, 50 Hz •Trip Function: Residual current / earth leakage protection •Accessories: Mounting terminals, screws, washers, cover / enclosure •Mounting: Flush or surface mounting on DB / panel

Supply and wiring of concealed exhaust/wall bracket fan point using PVC insulated, unsheathed, multi-stranded FRLS copper cable 1.5 mm² single core (as per IS 694/1990), laid 25 through suitable size (19 mm) PVC concealed rigid conduit pipe (wall thickness 2 mm), complete with ceiling rose, 10 A one-way modular switch in 1/2 M concealed unbreakable GI modular box, 2 M cover plate, including 1 mm² unsheathed copper wire for earth continuity, as required and as directed by Engineer-in-Charge at site.

Supply, fitting, fixing, connection & commissioning of 300 mm sweep heavy-duty exhaust fan, including all mounting arrangements, fasteners, brackets, and necessary consumables supplied by the contractor, as per site conditions and direction of Engineer-in-Charge.

Supply, erection, testing & commissioning of heavy-duty 400 mm sweep Wall Bracket 27 Fan, suitable for single-phase 230 V AC supply, complete with motor, blades, and all accessories, including fixing arrangement, brackets, screws, washers, and mounting consumables, as per direction of Engineer-in-Charge at site.

Supply and wiring of geyser point complete with 15/16 Amp socket outlet, 16 Amp DP MCB for overload and short circuit protection, suitable for 230V, single phase, 50Hz AC supply. The point shall be wired with 4 sq.mm single core PVC insulated FRLSH copper conductor flexible industrial unsheathed cable for phase and neutral, drawn through heavy duty PVC rigid concealed conduit pipe including necessary accessories such as PVC bends, tees, junction boxes, saddles etc. The earth continuity conductor shall be 1 sq.mm single core PVC insulated unsheathed flexible copper wire drawn along with the circuit wiring. The work includes making necessary wall chases, fixing conduit, box, accessories, proper termination, connection to existing distribution board, testing and commissioning complete. The concealed portion after wiring shall be properly plastered and finished; if required, the surface shall be painted by the contractor to match the existing surface colour, complete as directed by Site Engineer.

Supply, installation, testing and commissioning of 3 kW, 25 litres capacity, 5-Star rated storage type water heater (Geyser) suitable for operation on 230V, single phase, 50Hz AC supply, complete with inner tank, heating element, thermostat, safety valve, mounting bracket, inlet & outlet connections, necessary fasteners, connection to existing water line and electrical wiring including earthing, testing and commissioning complete as directed by Site Engineer. Technical 29 Parameters: 1.Capacity: 25 Litres 2.Rated Power: 3 kW 3.Voltage: 230V ±10%, Single Phase, 50 Hz 4.Energy Rating: 5 Star (as per BEE latest notification) 5.Inner Tank: Glass-lined / Porcelain enamel coated with corrosion protection 6.Heating Element: Copper / Incoloy heating element 7.Thermostat: Adjustable thermostat with automatic thermal cut-out 8.Safety: oMultifunction safety valve (pressure relief) oOverheat protection oDry heating protection 9.Working Pressure: Minimum 8 bar (suitable for multi-storey buildings) 10.Insulation: High density PUF insulation 11.IP Rating: Minimum IPX4 12.Warranty: •Inner Tank: Minimum 5 years •Heating Element: Minimum 2-3 years •Product: Minimum 2 years

Supply, fitting and laying of single-core 2.5 sq.mm Flame Retardant (FR) PVC 30 insulated industrial-grade multistrand copper conductor (unsheathed), flexible cable, voltage grade up to 1100 V, conforming to IS 694:2010, including all necessary supports, clamps, fixing accessories, and as directed by Engineer-in-Charge at site.

Supply, installation, testing and commissioning of 3 Watt LED Foot Lamp Light having minimum 300 lumens output with 90° beam angle, suitable for 230V AC, 50 Hz supply. The fitting 31 shall be complete with LED driver, housing, necessary mounting accessories, wiring connections, fixing hardware, and all allied materials required for proper installation. The work includes fixing at designated locations, connection to existing wiring, proper earthing, testing for satisfactory operation, and handing over in complete working condition as per instructions of Engineer-in- Charge.

Supply and fitting of 0.5 Watt LED Night Bulb suitable for 230V AC, 50 Hz operation, 32 complete with holder compatibility and necessary accessories. The LED bulb shall be of approved make and energy-efficient type with adequate illumination for night lighting purposes. The work includes fixing at designated locations, connection to existing wiring, testing for proper operation, and handing over in complete working condition as per instructions of Engineer-in-Charge.

Laying, installation, testing and commissioning of LT/HT XLPE insulated, armoured aluminium conductor power cable of different sizes, partly laid along pole/structure and partly laid 33 underground through excavated cable trench, complete as required at site. The work includes loading, unloading and carrying of Railway-supplied cable to actual work site by contractor's own arrangement, straightening, dressing, clamping on pole with suitable saddles/clamps, laying in trench, sand cushioning, protective covering with bricks/tiles, backfilling, compaction, route marking, and testing before and after laying, complete as directed by Engineer-in-Charge.

Excavation of cable trench 1.0 m x 0.5 m below the GL with laying of armored cable 34 and refilling the same by supply of Brick, Sand and Soil after digging the earth asper direction of Engineer at site & connection of armored Cable by supply and fixingof crimping lugs etc. The work includes supply and laying of sand cushioning, brick protection, and refilling with excavated soil, proper compaction and restoration of surface to original condition as directed by Engineer-in-Charge.

Supply, laying, fitting and commissioning of 110 mm (OD) diameter Double Wall Corrugated (DWC) HDPE pipe, PN-6.0 kg/cm², conforming to IS: 14930 (Part-II) - latest amendment, suitable for cable protection, laid partly over ground and partly underground.The work shall include 35 supply of pipe with all necessary accessories such as sockets, bends, couplers, end caps, reducers (if required), cutting, jointing, alignment and proper fixing in position.For underground portion, excavation (if required), laying at required depth, backfilling and compaction shall be carried out. For over ground portion, proper clamping/support arrangement shall be provided.The item includes all labour, materials, tools, tackles and incidental charges required for complete installation and commissioning. Complete in all respects as per direction of Engineer-in-Charge at site.

Supply, laying, jointing and testing of 100 mm dia Cast Iron (CI) Pipe, Class B, 36 conforming to IS:1536/2001 with Amendment No. 1 & 3, complete with all fittings, specials, jointing materials, lead/tyton rubber gaskets, nuts, bolts and accessories as required. The work includes excavation, lowering, alignment, jointing, testing for leakage, backfilling, and restoration of surface to original condition, complete in all respects as per directions of Engineer-in-Charge.

Supply, fitting, fixing, connection and commissioning of 18/20 Watt LED indoor batten fitting, complete set with LED tube, electronic driver, housing, end caps and all accessories, suitable for operation on 230V, 50Hz AC supply. The fitting shall be connected with 1.5 sq.mm FR PVC insulated flexible copper conductor wire drawn through PVC pipe/casing & capping as required at site, including connection to existing wiring, testing and commissioning complete as required.

Supplying, installation, Testing & Commissioning of LED Recessed / surface 12-15 watt Powder coated die cast /Extruded aluminum Body including trim. Down lighter Round SMD type body material with PMMA and prismatic diffuser and construction as per IS :10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.0.95, IP20, CRI >80 ,UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends , CCT 3000°K / 38 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. "complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy 120 <135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C).

Supply, Installation, Testing and Commissioning of ceiling fan with 1400 mm Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal ( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power 39 Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as required.

Supply, installation, testing and commissioning of 5 kVA True Online UPS conforming to latest applicable IS/IEC standards, based on IGBT-PWM technology with inbuilt isolation transformer, suitable for continuous operation. Technical Specifications: Rated Capacity: 5 kVA Technology: IGBT-PWM based, Double Conversion Online Input: 160V-260V AC, Single Phase, 50 Hz Output: 230V AC ±1%, Single Phase, 50 Hz Output Waveform: Pure Sine Wave Transfer Time: Zero 40 (No-break supply) Overall Efficiency: 80% and <90% Protection: Overload, short circuit, battery deep discharge, input under/over voltage, over temperature Display: LCD/LED status indication for input, output, battery and fault conditions The UPS shall be complete with isolation transformer, internal wiring, control circuitry, static bypass, necessary terminals, and earthing arrangement. The work includes installation at site, connection with existing mains and load, testing for performance parameters, and commissioning complete in all respects as per direction of Engineer-in-Charge. The quoted rate shall include all materials, labour, accessories and minor items required for proper installation and satisfactory operation of the system.

Supply and testing of 150 AH , 12 V SMF Battery conforming to JISC: 8702/1998 (Part 1,2 & 3) with latest amendments having warranty of one years. All consumables regarding fixing arrangement will be supplied by the contractor as per the direction of engineer in charge at site.

Supply and erection of earthing by made of B class GI pipe of 4000 mm length, 50 mm diameter & 3.6 mm thickness. The GI Strip 50x6 mm ( should be welded with the earth pipe). The pipe is provided with at tampered casing at the lowerend in order to facilitate the driving. A funnel with perforated plate to be provided at the top of the pipe for pouring water during dry season to have an effective earth value.The connecting conductor from earth electrode to the distribution 42 panel board should not be thinner than8 SWG GI wire to carry the fault current. The earth fill shall be of homogeneous layer of common earth soil.Where soil restivity is high,earth restivity enhancing material may be used,Bentonite or similar earth enhancing material may be used in rocky soil. Earth box to be precasted RCC and The values of earth resistance measured should be painted on the Earth pit cover/lid along with the date of measurement. As per Drg.No. DRG NO: PCEE/ELG/DRG/2024/1/Rev-1 dated 28.07.2025 & as per Technical circular no.EL/PS/2025/1 (Pipe Earthing arrangements)

Supply, installation, testing and commissioning of 250 KVA, 11/0.433 KV step down, 3 Phase (continuous loading) BEE 5 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender), 50 Hz, Dyn 11 vector group, ONAN copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented Core grade MOH or better, suitable for outdoor/indoor applications with On Load Tap Changer on HV side having AVR relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking arrangement on LV side including supplying and laying of copper conductor multicore control cable from transformer to HT breaker/panel for safety tripping, complete with all accessories and safety provisions as per relevant IS Code including first filling of filtered dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked and as per CPWD specifications complete in all respects etc as required at site. The permissible temperature-rise shall not exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and 43 45 dg. C for above 200 KVA for winding. Inside of tank shall be painted with varnish or liquid resistant paint. For external surfaces one coat of thermo setting powder paint or one coat of epoxy primer followed by two coats of polyurethane base paint shall be used. IS: 1180 (Part 3) shall be referred to for paint thickness for normal to medium corrosive atmosphere. Design ambient condition : a) air temperature 50 deg C, b) Relative Humidity 90 % Max, c) Altitude as per location/site. Noise level Shall not exceed limits as per NEMA TR-1 with all accessories running measured as per IEC 551 / NEMA standard. The transformer should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc. Marking Each transformer shall be provided with rating plate made of anodized aluminum/ stainless steel material securely fixed on the outer body, easily accessible,as per IS: 1180 Part-3. The following fittings and Accessories shall be provided:- a) Two earthing terminals with the earthing symbol b) Oil level gauge indicating oil level at minimum, 30°C and maximum operating temperature; c) Air release device (for non-sealed type transformers) d) Rating and terminal marking plates; e) Silica gel breather f) Drain-cum-sampling valve (¾ nominal size thread, IS 554) preferably steel with plug for three phase transformers; g) Thermometer pocket with cap; h) Oil filling holes having (1¼ nominal size thread) with cover (for sealed type transformers without conservator); i) Lifting lugs for the complete transformer as well as for core and winding assembly; j) Pressure relief device or explosion vent ; k) One filter valve on the upper side of the tank ; l) Unidirectional flat rollers; m) Inspection hole; n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth); o) Arcing horns or suitable rating lightning arrestors for HT side - 3 Nos. q) Bird guard; r) Oil temperature indicator and winding temperature indicators for transformers.

Construction of transformer pad by CC foundation in ratio 1:1.5:3 by cement,sand and stone chips by observing the IE rules and as per direction of Railway Engineer. The work shall be 44 carried out in accordance with IE Rules and as per directions of Railway Engineer.The drawing/design of the transformer pad shall be prepared by the contractor and got approved from the competent authority prior to execution.The rate shall include all materials, labour, tools, tackles and minor items required for completion of work.

Design, fabrication, supply, carrying and erection of 12 m height swaged type (410- SP-66) G.I. Tubular Pole including supply and fixing of base plate and pole cap, complete in all respects.The pole shall be erected by earth excavation to a depth of 1/6th of the pole height and grouted with CC foundation in ratio 1:2:4 (cement : sand : 20 mm nominal size stone aggregate). The size of CC block shall be 30 cm diameter, extending up to the full pole depth below ground level 45 and 30 cm above ground level for muffing.The pole shall be hot dip galvanized with average zinc coating thickness of 70 microns conforming to IS:2629 / IS:2633 / IS:4759. Swaging, welding and base plate welding shall conform to IS:2713. Pipe material shall conform to IS:1161 / IS:1239 and the pole shall be designed to withstand wind load as per IS:875. The work includes providing anti- climbing device using barbed wire up to 2.5 m height with necessary GI clamps, nuts and bolts. A Danger Board (8" x 6") indicating voltage grade and skull symbol shall be fixed with suitable GI clamps.The entire work shall be executed as per directions of Engineer-in-Charge at site and the rate shall include all materials, labour, tools, tackles and incidental charges required for completion.

Supply, stringing and binding of ACSR conductor conforming to IS:398 (Part-II)-1976, 46 Raccoon size 6/1 x 4.09 mm, including necessary binding, clamping and jumpering complete in all respects. The conductor shall be properly tensioned and sagged as per standard practice. No joint shall be permitted within a single span.The work shall be carried out as per relevant IS specifications and directions of Engineer-in-Charge at site.

Supply, installation , testing and commissioning of Triple pole Air- break Gang 47 Operating air break off load disconnecting switch (GOS) 11 KV 400 Amp. complete with drop out fuses, 3 insulator triple pole each pole consist of galvanize steel base HT insulator as per BIS non ferrous knife and spring loaded contact arcing horn of adequate section to break magnetizing current of the transformer horizontal GI shaft/ pipe of adequate length for phase separator, adequate length for operation from ground level and operation handle complete with locking arrangement in both OFF & ON position. All ferrous part heavily tinned with stand weather . Fuse shall be conforming to IS:9385 part-I/1979, GOS shall be conforming to IS: 9921 Part-I/1981&9921 Part III/1982.complete with operating rod , drop out fuse and locking arrangement etc. conforming to IS: 1811 1992 or latest including provision of mounting arrangement for GOS as req.The whole work shall be executed as per direction of Engineer in charge at site

Supply and fixing of GI angle of size 50 x 50 x 6 mm, clamped with GI flat 50 x 5 mm 48 using 50 x 16 mm bolts and nuts, for holding insulators and lightning arresters, including drilling of necessary holes.Providing and fixing 2200 mm long bracket for cross bracing for six pole structure (2 sets) for transformer mounting.The work includes surface preparation and painting complete in all respects as per direction of Engineer-in-Charge at site.

Supply & fixing of GI angle of size 50X50x6mm clamped byGI flat 50x5mm with 49 50x16mmbolts, nuts for holding insulators, lightning arrester with necessary hole by drill including painting ( 3300 mm long bracket for cross bracing)(for 2 job of six pole structure for transformer mounting).

Supply and fixing of GI angle of size 50 x 50 x 6 mm, clamped with GI flat 50 x 5 mm 50 using 50 x 16 mm bolts and nuts, for holding insulators and lightning arresters, including drilling of required holes.Providing and fixing 3300 mm long bracket for cross bracing for six pole structure (2 sets) for transformer mounting.The work includes surface preparation and painting complete in all respects as per directions of Engineer-in-Charge at site.

Supply and erection of Galvanized stay set for HT OH line complete with 19/20 mm 51 diameter 1.8 Mts.long stay rod, Anchor plate of size30x30 cm x 6 mm thick, thimble,stay clamp turn buckle (20 x 600)mm, 7/10 SWG stay wire andstrain insulator etc. in CCfoundation of ratio 1:2:4:including excavation/refilling etc.as per direction at site Engineer in- charge of Railway.

Supply, installation, testing and commissioning of gapless, metal oxide (ZnO) type, polymer housed, distribution class Lightning Arrestor suitable for 11 kV, 3-phase overhead line system. Technical Specifications: •System Voltage: 11 kV •Rated Voltage (Ur): 9 kV (RMS) •Nominal Discharge Current: 5 kA (8/20 µs waveform) •Type: Gapless Metal Oxide (MOV), non-linear resistor type •Housing: Polymer / Silicone rubber, weather resistant, suitable for outdoor installation 52 •Creepage Distance: As per applicable IS/IEC for polluted atmosphere •Short Circuit Withstand Capability: As per relevant IS/IEC standard •Pressure Relief Capability: Adequate to prevent shattering under fault conditions The lightning arrestor shall conform to latest IS/IEC 60099 (Part-4) or relevant standard and be suitable for continuous operation under site conditions.The work includes mounting on pole/structure, connection to phase conductor and earthing system with suitable GI/copper earth lead, clamps, nuts, bolts and accessories, testing for insulation resistance and proper continuity, and commissioning complete in all respects. All works shall be carried out as per directions of Engineer-in-Charge and relevant electrical safety standards.

Supply, installation, testing and commissioning of pipe earthing set comprising 80 mm dia medium gauge G.I. pipe electrode, 4.0 m long, conforming to relevant IS specifications, complete in all respects.The electrode shall be installed vertically in excavated earth pit of suitable dimensions. The earth pit shall be constructed with brick masonry chamber and provided with CI/GI cover and frame.The earthing electrode shall be connected with 25 x 3 mm G.I. strip as earth lead, 53 securely fastened with GI nuts, bolts, washers and clamps. Proper anti-corrosion treatment shall be applied at all joints.The earth pit shall be filled with alternate layers of charcoal/coke and salt around the electrode, properly compacted and watered to achieve low earth resistance.The work includes excavation, lowering of electrode, strip laying, backfilling, watering arrangement, testing of earth resistance using approved earth tester, and achieving earth resistance value as per IE Rules/IS 3043 requirements.Complete installation shall be carried out as per directions of Engineer-in-Charge at site.

Supply, installation, testing and commissioning of heavy-duty industrial/commercial grade kitchen chimney system suitable for continuous operation in institutional/railway kitchen environment, complete in all respects. Technical Specifications: •Body Material: Minimum 18 SWG stainless steel (SS-304 grade) or better, corrosion resistant, suitable for high temperature and 54 greasy environment •Type: Wall mounted / canopy type (as per site requirement) •Suction Capacity: Minimum 1200-2000 CMH (as per kitchen load) •Motor: Heavy duty copper wound motor, continuous duty rated, dynamically balanced blower assembly •Power Supply: 230V / 415V AC, 50 Hz (as applicable) •Filters: Stainless steel baffle filters / multi-layer SS filters, removable and washable type •Noise Level: Not exceeding 65-70 dB at rated capacity •Ducting: GI/Aluminium duct with necessary bends, clamps, supports and weatherproof outlet hood •Control: On/Off switch / speed regulator panel Scope Includes: •Fabrication and fixing of supporting frame/brackets •Complete ducting with sealing of joints and proper alignment •Electrical wiring from nearest power point including MCB/isolator, earthing and necessary protection •Testing of suction efficiency, vibration level and operational performance •Commissioning complete in all respects The entire installation shall conform to relevant IS standards and electrical safety norms. All materials, labour, consumables and minor items required for proper installation and satisfactory operation shall be included in the quoted rate. The work shall be executed strictly as per directions of Engineer-in-Charge at site.