SITC of 01 no 13 Passenger (884kg) New lift in (G plus 2 storied) Annex Building at North Calcutta Polytechnic college, Kolkata- 700002.

Amount

SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to relevant IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd.

Make : Lift manufacturers approved under Category-I

Type: Passanger Lift .

Load : 13 Passenger / 884 Kg

Control: Microprocessor based with serial communication controller in shaft & user interface in landing ( VVVF)

Machine:- Energy efficient machine, Gearless, without Machine Room

Speed: 1.0 Mtrs./ Sec

Floor served: G + 2

Landing: 3, all on same side

Total Rise : 6.7 Mtr (approx.)

Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. COP & LOP must have stainless steel face plate silver brushed with surface mounted button. Button : All buttons on car & landing shall be luminous, on/off switch for Lift, fan, light, toggle switch or key switch for automatic/attendent mode of operation. Display type :Colour LCD / Segmented LCD/ LED Operation Push Button for lift maintenance & service should be on top of the car.

Leveling accuracy:± 5 mm(Micro levelling arrangement )

Car inside :1100mm ( W ) x 2000mm ( D ) x 2200mm (H) or as per OEM standard.

Car Entrance:Clear Opening:- 800 mm (W) x 2000 mm (H ) protected with car door or as per OEM standard.

Car Finish & Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

a) Rear Mid Panel ---- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

b) Rare corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

c) Side Mid Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

d) Side corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

e) Front Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

Car Ceiling & Lighting: Stainless Steel with hairline finish (#4) with LED lighting and Fan

Car Ventilation: Cross flow Pressure fan with anodised aluminium grill.

Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening (COPD) automatic door provided with AC V3F controlled door drive system with full height infrared curtain of light and mechanical force limiting device,with fire rating of minimum 120 minutes.

Landing Door: Stainless steel centre opening (COPD) automatic door provided with AC V3F controlled door drive system, with fire rating of minimum 120 minutes.

Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor/ infrared detector.

ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room

Emergency Alarm: Battery operated alarm bell system in lift car and control room

Fireman switch: Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. Car parking at top floor at idle condition.

Main rope / Steel Belt :- As per manufacturer's standard conforming to respective applicable IS

Hand Rail:-Stainless Steel Mirror Finish Handrails on rear car panels

Auto fan cut-off

Proposed Shaft Dimension: 2000 mm (W) X 2500 mm (D)

Proposed Pit Depth :1350 mm or as per actual site condition. (Bidder should visit the site)

Proposed Overhead : 4500 mm or as per actual site condition. (Bidder should visit the site)

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

Note: 1) All the above rates should be quoted inclusive of all taxes & duties and LWC as applicable. 2) Total is rounded off to the nearest rupees. N.B. N.B. (1) The Agency must procure the materials from the Manufacturer / OEM or from their authorised sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them 2) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution, of work/submission of bill. 3) The Defect Liability period for the work is 1(one) year. 4) Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish. 5) Necessary MS member e.g.; angle iron, MS channel brackets etc as required to be provided by the manufacturer.

SCHINDLER INDIA PRIVATE LIMITED (BID ID -6319463)