MISC REPAIRS TO HARD STANDING AND ROAD SIDE FURNITURE AND CERTAIN B/R REPAIR UNDER ZONE IA AREA AT JAIPUR MIL STN

Amount

M&L for preparation of old concrete surfaces of any description over 10cm girth or width, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

_dittio_ all as per item No 2 above but two coats.

M & L for preparation of old surface of walls and applying one coat of cement paint of any tint complete all as specified and directed.

_dittio_ all as per item No 3 above but two coats of cement base paint.

M&L preparation of old steel surface and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L broken stone or boulders for hardcore of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15cm thick watered and rammed to a ture surface complete all as specified and directed.

M & L plain Cement Concrete1:4:8 type D-2 (40mm graded aggregate) in sub base of floors complete all as specified and directed.

M & L 75 mm thick plain Cement Concrete 1:2:4 type B-2 (40mm graded aggregate) in sub base of floors complete all as specified and directed.

M & L 40mm thick plain Cement Concrete 1:2:4 type B1 (20mm graded aggregate) in sub base of floors complete all as specified and directed.

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in cement mortar complete all as specified and directed.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement laid over and including 25mm thick sand cushion layer complete all as specified and directed.

M & L Machine pressed precast concrete rubber moulded interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement laid over and including 25mm thick sand cushion layer complete all as specified and directed.

_dittio_ all as per item No 13 above but except tiles

M&L rubber moulded chequered cement concrete tiles 20cm x 20cm x 20mm thick , set , jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm thick screed bed in CM 1:6 complete all as specified and directed.

_dittio_ all as per item No 15 above but except tiles.

M & L precast PCC blocks or slabs 150 mm thick (1:2:4) mix type B-1 using 20 mm graded aggregated with plain or interlocking joints as directed complete in walls setting in CM (1:6) complete all as specified and directed.

Demolation of precast RCC jallies including raming of any description any in any position set in cement mortar complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) louvers and jallies 35mm thick (measured solid) including all mouldings but excluding frame & set in CM 1:4 complete all as specified and directed.

Demolition of un-reinforcement cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L precast reinforced cement concrete slab type B1, 1:2:4 ( 20mm graded aggregate ) as in landing, drain cover slab ( for manholes etc ) , chajjas , drain cover and shelves and similar articles with plain faces complete all as specified and directed. (Reinforcement shall be measured & paid separately.)

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

_dittio_ all as per item No 22 above but 6mm to 8mm dia.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 for raising of height of drain, manhole / wall complete all as specified and directed.

All as per item No 25 herein before but except brick.

Taking down cement plaster or cement lime plaster on brick / stone surfaces of wall or ceiling including raking outs joints, hacking for key scrubbing down with water etc complete all as specified and directed.

M & L rendering 15mm thick on stone masonary surfaces or surface other than fair faces of brick work on wall in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L rendering 15mm thick on fair faces of brick work or concrete surfacel in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered wall surfaces and applying two coats of cement base paint on wall complete all as specified and directed.

M&L for granite (of any type), 16mm to 18mm work (table rubbed and polished) in steps, jamps, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for Dholpur stone 16 to 18 mm cladding gang saw cut with macnine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one mumber SS clamps (grade-202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fasterner, polishing,rubbing & including silicon treatment complete all as specified and directed.

M & L machine cut kota stone slab flooring 20-25mm thick,size of kota stone 450x450 mm over and including cement screed bed 20mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

S&F rolled mild steel work as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the lenght directed) and similar work conforming to Fe-290 GdeE-165 complete all as specified and directed.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape hand rail straight portion , drilled and contersunk for balusters , nosing to steps, struts in fencing including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets ( for securing chain link fencing ) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed.

S&F in repair mild steel round bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for chain link fening ( in new or old ) complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified and directed.

Dismantling galvanised chain link fencing of any description fixed to any type of fencing posts complete all as specified and directed.

Supply only chain link fencing 3to 4 mm dia galvanized steel 50mm x 50mm mesh fixed to angle iron fencing post or angle frame complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

S&F screw bolts (machine made) with hexagonal or square head at one head and rounded the other or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut exc 10cm nexc 15cm long dia of shank 11 to 15mm.

S&F as in repair galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc complete all as specified and directed.

M&L preparation of new steel surface of any description n. exc 10cm in width or girth when un connecting to other painting surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coarch screw and washer in roof wall etc complete all as specified and directed.

M&L pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness including nainital or similar pattern roof /wall covering complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S & F steel work in tubular/ square/ rectangular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforiming toIS 1161-1979 graded St-240 complete all as specified and directed.

S&F mild steel, plain black sheet 1.25 mm in hearths, covering to door shutter, covering to door chowkhats (frame), chullah hoods etc cut to size edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fiwed ro steel members etc with plain 40mm lap joints or welded / riveted , seams including bending , turning up mitred angles stopped ends, outlets etc as required.

M&L for prearation of new steel surface and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L plain cement concrete type B1 1:2:4 ( 20mm graded aggregate) as in lintels, cills steps, seismic and other similar bands , copings, kneelers, apex stone bed plates , kerb ,water troughs and like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F Sign board made out of 03mm aluminum composite panel both side alongwith retro reflective sheeting on both side with letters, stops, commas, short lines, dashes, hyphen, brackets etc of 100-150mm size fixed on 75mm dia SS Pipe of 3 mtr long complete all as specified and directed. Note: 1. Area of sign board shall be considered for payment.

M & L for painting lines dashes, letters etc on road pavements and likes n,exe,10cm wide with road marking tharmoplastic paint white/yellow complete all as per specification and direction.

Road Stud (Cateyes) globe of complete all as per manufacture specification. Make M/s Futurvista or M/s Parshva Plastics, Mumbai or equivalent as approved by GE.

S&F in repair solar road stud (aluminium alloyed) with storage battery : Ni - MH (1200mAH) and LED qty - 3 pieces each side complete size 125 x 125 x 21mm (50mm shank) all as per manufacture specification (Make : Dark Eye or equivalent as approved by GE)

S&F as in repair delineators made of ABS round body fitted with two Nos 100mm dia high reflective reflectors on both sides and having a pipe (duly powder coated), sponsor plate can also provide for sponsorship two small rectangular reflectors of size 70mm x 23mm x 2 Nos each side provided for better reflectivity on pipe 100 cm long painted with white/black colour provided, embedded in PCC 1:2:4 type B1 with 20mm graded stone aggregate (size of block 15 cm x 15cm x 10cm) complete all as specified and directed. Cat part No DA 74 of make Dark Eye or equivalent as approved by GE.

Schedule of Credit

S.R.Enterprises

MSR INFRATECH

M/S JALANDRA CONSTRUCTIONS

M/S Mohan Lal Gupta

J.J.ENGINEERING

Smita Constructions