Loading
Loading…
Loading…
Tender Value
₹2.8 Cr
EMD Value
₹5.6 L
Closing Date
2 Jul 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Capital (Works)
TENDER
25 conditions · 5 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less ; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, long with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies/ PSUs authorities. Certificates issued by Private Bodies will not be considered.
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above.(ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii)Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets or Provisional Balance sheet. (iv) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above,the tender shall be rejected. No post-tender correspondence will beentertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfilment of the Para No.17.15.2 of J.V guide lines of IRSGCC April - 2022 [with up to date correction slip].
Similar Nature of Work: " Single Similar Nature of Work (A & B) (A) Any civil engineering work with building construction / building maintenance O R Any civil engineering work with CC Road / Bituminous Road work. AND (B) Tenderer should have a valid electrical contractor's license in his / their name or the tenderer should give an undertaking that he will engage Agency for electrical work with valid electrical contractor's license in his/their own name. Note: - If tenderer fails to upload the electrical contractor's license or undertaking certificate with regard to engagement of electrical contractor with valid electrical contractor's license his offer will be summarily rejected.
Maintenance period Three years.
116 conditions · 39 needing a document upload
TENDER SHALL BE REJECTED if it is not accompanied by the following.
Bid Security deposited through IREPS e-payment or as per provisions under Clause 5 (2) Part-I of GCC April 2022.
Uploading of Certificate in support of Technical Eligibility (No Technical credentials are required for tenders having advertised value up to Rs 50 lakh).
Submission of Certificate(s) in support of Financial Eligibility (No Financial credentials are required for tenders having advertised value up to Rs 50 lakh).
TENDER SHALL BE REJECTED if it is not accompanied by the following.
In case of Partnership firm: The tender form shall be submitted only in the name of partnership firm.
In case tenderer is JV Firm : The tender form shall be submitted only in the name of the JV and not in the name of any constituent member.
IN CASE THE TENDER is Partnership firm/ JOINT Venture firm (JV)/ LLP A copy of certificate to be submitted/uploaded by tenderer as per format given at annexure -v of IRGCC 2022.
In case tenderer is other than sole proprietorship firm, following documents shall be uploaded by the tenderer:
In case the Tenderer is a Partnership Firm: [i] A notarized copy of Partnership deed or a copy of the Partnership deed registered with the Registrar. [ii] A notarized or registered Power of Attorney (duly registered as per prevailing law) in favour of an individual to sign the tender documents and create liability against the Firm. [iii] PAN / TAN number of Partnership firm (PAN / TAN number in the name of any of the constituent partners shall not be considered). [iv] All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
In case the Tenderer is a LLP Firm registered under LLP Act-2008 (i) A copy of LLP Agreement, (ii) A copy of Certificate of Incorporation; and (iii) A copy of Power of Attorney/Authorization issued by the LLP Firm in favour of the individual to sign the tender on behalf of the LLP Firm and create liability against the Firm. (iv) Copy of PAN number of the LLP Firm. [v] All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.L
In case the Tenderer is a Company registered under Companies Act-2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by theresolution of Board of Directors) in favour of the individual to sign the tender on behalfof the company and create liability against the company.(iv) copy of PAN number of the Company. and (v) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.
In case the Tenderer is a Registered Society & Registered Trust: (i) A copy of the Certificate of Registration. (ii) A copy of Memorandum of Association of Society/Trust Deed; (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. And (iv)A copy of Rules and Regulations of the society (v) Copy of PAN number of the Society/Trust. (vi) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.
Incase JV Firms are allowed to participate: Uploading of MEMORANDUM OF UNDERSTANDING as per the format given in "Documents attached with tender" and also below documents.
In case one or more members is/are Proprietary Firm or HUF, the following documents shall be enclosed: (i) A copy of notarized affidavit on Stamp Paper declaring that his/her Concern is a Proprietary Concern and he/she is sole proprietor of the Concern OR he/she is in position of "KARTA" of Hindu Undivided Family (HUF) and he/she has the authority, power and consent given by other partners to act on behalf of HUF.
In case one or more of the members of the JV is/are partnership firm(s), following documents shall be submitted: (i) A notarized copy of the Partnership Deed or a copy of the partnership deed registered with the Registrar. (ii)A copy of consent of all the partners or individual authorized by partnership firm, to enter into the Joint Venture Agreement on a stamp paper. (iii) A notarized or registered copy of Power of Attorney in favour of the individual to sign the MOU/JV Agreement on behalf of the partnership firm and create liability against the firm.
In case one or more members of the JV is/are companies, the following documents shall be submitted: (i) A copy of resolutions of the Directors of the Company, permitting the company to enter into a JV agreement. (ii) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company. (iii) A copy of Certificate of Incorporation. (iv) A copy of Authorization/copy of Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender, sign MOU/JV Agreement on behalf of the company and create liability against the company.
In case one or more members of the JV is/are LLP firm/s, the following documents shall be submitted:(i) A copy of LLP Agreement. (ii) A copy of Certificate of Incorporation of LLP. (iii) A copy of resolution passed by partners of LLP firm, permitting the Firm to enter into a JV agreement. (iv) A copy of Authorization /copy of Power of Attorney issued by the LLP firm (backed by resolution passed by the Partners) in favour of the individual, to sign the tender and/or sign the MOU/ JV agreement on behalf of the LLP and create liability against the LLP.
In case one or more members of the JV is/are Society/s or Trust/s, the following documents shall be submitted: (i) A copy of Certificate of Registration. (ii) A copy of Memorandum of Association of Society/Trust Deed. (iii) A copy of Rules & Regulations of the Society. (iv) A copy of Power of Attorney, in favour of the individual to sign the tender documents and create liability against the Society/Trust.
Uploading of Declaration regarding Employment of Retired Engineer/Retired Railway Officer as per clause no.16 of Part-I of GCC April 2022. [in the format attached in - Documents]
(i) The tenderer shall clearly specify whether the tender is submitted on his own (ProprietaryFirm) or on behalf of aPartnership Firm / Company / Joint Venture (JV) / Registered Society /Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. Thetenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PANCard along with their tender. TenderDocuments in such cases are to be signed by such persons asmay be legally competent to sign them on behalf of the firm, company, association, trust or society,as the case may be.(ii) documents shall be submitted according to clause 14 of IRGCC 2022:
IN CASE OF ADVERTISED TENDER VALUE IS MORE THAN RS. 20 CRORES: The tender/technical bid will be evaluated based on bid capacity formula detailed as Annexure-VI of IRSGCC April - 2022. NOTE: i)The Tenderer(s) shall furnish the details of existing commitments and balance amount of ongoing works with tenderer as per the prescribed proforma of Railway for statement of all works in progress and also the works which are awarded to tenderer but yet not started up to the of inviting of tender. In case of no works in hand, a 'NIL' statement should be furnished. This statement should be submitted duly verified by Chartered Accountant.(ii) In case, the tenderer/s failed to submit the above statement along with offer, their/his offer shall be considered as incomplete and will be rejected summarily.
Uploading of NEFT FORM - as per the format attached with the tender document.
The list of personnel / organization on hand and proposed to be engaged for the tendered work.
List of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work.
Uploading of Statement Showing the particulars of Works on Hand & Works Completed as per the format attached to the tender document.
Uploading of certificate by local suppliers in regard to meeting the Minimum Local Content requirement to avail benefits under Public Procurement Policy Order-2017, as amended from time to time, shall be followed for consideration of tenders(A) for procurement order of value less than Rs. 10 crores: self- certificate in accordance with Para-9(a) of Public Procurement(Preference to Make in India) Order 2017. (B)For Procurement Order of value more than Rs. 10 crores, the certificate from Statutory auditor/cost auditor/practicing CA as the case may be in accordance with Para-9(b) of Public Procurement (Preference to Make in India) Order 2017.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Construction of building for storage and office accommodation, improvements to roads, sheds and buildings for stores inside factory premises of RWF
W496RWFYNK1087~RWF
W496RWFYNK1087
Open
Works - General
9 Months
Bengaluru Urban, Karnataka
₹0
₹5.6 L
2 Jul 2026
10 Jun 2026
18 Jun 2026
73 items across 3 schedules · ₹2,26,52,890.53 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. | cum | 800 | 411.3 | 3,29,040 |
| 2 | All kinds of soil | cum | 693 | 205.45 | 1,42,376.85 |
| 3 | Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm | Metre | 100 | 651.55 | 65,155 |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | cum | 210 | 253.95 | 53,329.5 |
| 5 | All kinds of soil | cum | 393 | 104.5 | 41,068.5 |
| 6 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 68 | 6,833.4 | 4,64,671.2 |
| 7 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 100 | 6,670.25 | 6,67,025 |
| 8 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. | Per bag of cement of 50kg | 400 | 57.15 | 22,860 |
| 9 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 280 | 307.95 | 86,226 |
| 10 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 615 | 766.55 | 4,71,428.25 |
| 11 | Lintels, beams, plinth beams, girders, bressumers and cantilevers | Sqm | 364 | 608.35 | 2,21,439.4 |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 237 | 804.25 | 1,90,607.25 |
| 13 | Stairs, (excluding landings) except spiral- staircases | Sqm | 31 | 657.75 | 20,390.25 |
| 14 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) | Sqm | 615 | 319.25 | 1,96,338.75 |
| 15 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 96 | 8,825.35 | 8,47,233.6 |
| 16 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 250 | 10,477.75 | 26,19,437.5 |
| 17 | Providing and laying Autoclaved Aerated concrete blocks (AAC) masonry 150mm/230mm/300 mm thick AAC with Grade-1 blocks of density 551-650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). | cum | 124 | 6,994.15 | 8,67,274.6 |
| 18 | Second class teak wood | cum | .3 | 1,31,576.95 | 39,473.09 |
| 19 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 23 | 2,015.75 | 46,362.25 |
| 20 | Fixed to openings /wooden frames with rawl plugs screws etc. | Kg | 252 | 197.7 | 49,820.4 |
| 21 | 125 mm | Each | 22 | 205.1 | 4,512.2 |
| 22 | Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 +/- 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) | Sqm | 2 | 7,249.9 | 14,499.8 |
| 23 | Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) | Sqm | 35 | 9,183.3 | 3,21,415.5 |
| 24 | 100mm | Each | 26 | 75.7 | 1,968.2 |
| 25 | Size of Tile 600 x 1200 mm | Sqm | 326 | 1,612.75 | 5,25,756.5 |
| 26 | Size of Tile 600 x 600 mm | Sqm | 62 | 1,311.05 | 81,285.1 |
| 27 | 75 mm diameter | Metre | 40 | 213 | 8,520 |
| 28 | 110 mm diameter | Metre | 33.4 | 319.75 | 10,679.65 |
| 29 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 1100 | 671.55 | 7,38,705 |
| 30 | Flashings/ Aprons.( Upto 600 mm) | Metre | 30 | 412.85 | 12,385.5 |
| 31 | 1:4 (1 cement: 4 fine sand) | Sqm | 2362 | 294.85 | 6,96,435.7 |
| 32 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 1761 | 214.3 | 3,77,382.3 |
| 33 | New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | Sqm | 1009 | 162.35 | 1,63,811.15 |
| 34 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | Sqm | 1761 | 158.95 | 2,79,910.95 |
| 35 | New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. | Sqm | 1009 | 154.45 | 1,55,840.05 |
| 36 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture | Sqm | 35 | 191.4 | 6,699 |
| 37 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm | 1200 | 123.85 | 1,48,620 |
| 38 | Two coats | Sqm | 5000 | 116.05 | 5,80,250 |
| 39 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre | Sqm | 1761 | 64.45 | 1,13,496.45 |
| 40 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete | Sqm | 1200 | 16.35 | 19,620 |
| 41 | One or more coats on old work | Sqm | 500 | 86.55 | 43,275 |
| 42 | One or more coats on old work | Sqm | 2000 | 79.4 | 1,58,800 |
| 43 | Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface | Sqm | 7000 | 111.6 | 7,81,200 |
| 44 | Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge. | Sqm | 600 | 540.35 | 3,24,210 |
| 45 | Asbestos Cement sheet | Sqm | 1100 | 63.75 | 70,125 |
| 46 | On bituminous surface @ 0.50 Kg / sqm | Sqm | 1600 | 36.6 | 58,560 |
| 47 | Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer | cum | 400 | 10,006.65 | 40,02,660 |
| 48 | New work (Two or more coats) | Sqm | 100 | 239.95 | 23,995 |
| 49 | Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in- charge. | Each | 50 | 175.5 | 8,775 |
| 50 | 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100- 120 TPH capacity. | cum | 80 | 10,870.75 | 8,69,660 |
| 51 | Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material within all lifts and lead upto 1km (by mechanical means). | Sqm | 1600 | 5.85 | 9,360 |
| 52 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in- Charge. | cum | 100 | 2,803.65 | 2,80,365 |
| 53 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 4 | 5,781.35 | 23,125.4 |
| 54 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 4 | 5,540.55 | 22,162.2 |
| 55 | Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern | Each | 6 | 8,115.55 | 48,693.3 |
| 56 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | Each | 4 | 2,275 | 9,100 |
| 57 | 510x1040 mm bowl depth 225 mm | Each | 1 | 6,677.4 | 6,677.4 |
| 58 | 20 mm nominal dia Pipes | Metre | 50 | 513.75 | 25,687.5 |
| 59 | 25 mm nominal dia Pipes | Metre | 50 | 626.05 | 31,302.5 |
| 60 | 32 mm nominal dia Pipes | Metre | 10 | 712.75 | 7,127.5 |
| 61 | 300 mm dia Ductile Iron Class K-7 pipes | Metre | 100 | 3,177.65 | 3,17,765 |
| 62 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. | Sqm | 62 | 516.6 | 32,029.2 |
| 63 | 35 mm thick | Sqm | 10.54 | 4,929.8 | 51,960.09 |
| Schedule total | ₹1,89,09,965.53 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
NEFTFORM.pdf
ATTACHMENT
ANNEXURE-AtoE.pdf
ATTACHMENT
CheckList.pdf
ATTACHMENT
ANNEXURE-VIB.pdf
ATTACHMENT
CERTIFICATIONOFFAMILIARISATION.pdf
ATTACHMENT
ANNEXURE-I.pdf
ATTACHMENT
GCC_IndianRailways-April-2022.pdf
ATTACHMENT
Contractore-MBIR-WCMS_1.pdf
ATTACHMENT
RailwayBoardLetterDtd31-05-2023.pdf
ATTACHMENT
StandardTenderDocumentVersion2.1.pdf
ATTACHMENT
conservencycesscharges.pdf
ATTACHMENT
GCCAdvancecorrectionslips1to11.pdf
ATTACHMENT
Milstone-storey.pdf
ATTACHMENT
Specialcondition-storystorey.pdf
ATTACHMENT
scopeofwork-storey.pdf
ATTACHMENT
tantitativeplaning-storey.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .