CWE/CHM-74/2024-25 WELCOME MAINT REPAIRS IN OFFRS MD ACCN IN SEC A UNDER AGE B/R I AT CHANDIMANDIR MIL STATION

Amount

Demolition of brick work built in cement mortar including all quoins, arches, pillar etc., complete including removing the waste materials up to a distance of 500 meters complete all as specified and directed by Engineer-in-Charge.

M&L for Brick work with sub class 'B' Bricks (old size bricks), straight or curved on plan exceeding 6 metre mean radius built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Supply only Integral waterproofing compound, ISI Marked, complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:4 on brick or concrete surfaces including mixing with WPC finishing even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note:- WPC shall be measured and paid separately.

M&L for Rendering 15 mm thick on brick work or concrete surfaces, finished even and smooth without using extra cement on walls in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of newly plastered surfaces of wall and applying wall care putty, not less than 2 mm thick over a coat of chalk whiting including smoothening the surfaces with sand papers etc, and applying two coats of OBD on wall surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated wall surfaces and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated Ceiling surfaces and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for Complete removal of existing treatment on wall surfaces and applying 3 mm thick wall care putty & smoothening the surfaces with sand papers etc., (preparatory to OBD/ plastic emulsion/ interior emulsion paint as directed), of any description complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated surfaces of wall and applying one coat of oil bound distemper, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated surfaces of wall and applying two coats of oil bound distemper, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of oil bound distemper, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated surfaces of wall and applying one coat of plastic (interior) emulsion paint, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old wooden surfaces of any description of width and girth and French polishing with one or more coats, melamine finish with spray pump including a coat of wooden filler on old works complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old steel and iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Taking up or down GI steel/ Kitek tubing, 15 mm bore with connections or fittings from wall, ceiling, floor etc., including cleaning of tubes for re-fixing complete all as specified and directed by Engineer-in-Charge.

Taking up or down GI steel/ Kitek tubing 20 mm bore with connections or fittings from wall, ceiling, floor etc., including cleaning of tubes for re-fixing complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of CPVC pipes 16 mm SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of CPVC pipes 20 mm SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and directed by Engineer-in-Charge.

M&L for Cutting chases, pinning in, making good to facing where required and pointing in CM (1:3) to ends or edges of landings, steps, cills, sunsheds, shelves, lintel etc and cutting chases for concealed water tubing or concealed conduit wiring etc n.exc 10 cm width or girth complete all as specified and as directed by Engineer-in-charge.

Supplying & fixing Polyethylene (PE-AL-PE) 16-20 mm composite pressure Crimp type internal sealing Plastic-Metal Composite fittings (such as tees, reducers, etc.) complete all as specified and as directed by Engineer-in-charge.

Supplying & fixing Polyethylene (PE-AL-PE) 20-25mm composite pressure Crimp type internal sealing Plastic-Metal Composite fittings (such as tees, reducers, etc.) complete all as specified and as directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top), HDPE, triple layered, white coloured with ISI marked of 1000 litres capacity with inlet & outlet connections, including 20 mm dia PVC float valve with ball & all fittings, tank nipple 150 mm long with washer & plug, with tank lid having locking arrangement hoisted and fixed in position including dismantling existing water storage tanks (RCC/ PVC) of any capacity complete all as specified and as directed by Engineer-in-charge.

All as per Serial item No. 28.00 here-in-before but of capacity 500 litres.

M&L for Cleaning and removing all scale and dirt etc from overhead water storage tanks of capacity exceeding 250 but not exceeding 500 litres and from mouths of circulating pipes etc complete all as specified and as directed by Engineer-in-charge.

All as per Serial item No. 30.00 here-in-before but of capacity exceeding 500 Litres and not exeeding 1000 litres.

S&F in repairs Gun-metal globe or gate valves, with iron wheel head, 15 mm bore, screwed both ends for iron pipe, complete all as specified and directed by Engineer-in-Charge.

All as per Serial item No. 32.00 here-in-before but for 20 mm bore

S&F in repair Ball valves, PTMT, high pressure, ISI marked, with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gm) complete all as specified and directed by Engineer-in-Charge.

Demolition of RCC as in slab, beams, chajjas, kitchen shelf and similar suspended work (reinforcement cut as required to facilitate demolition) including necessary scaffoldings required, if any complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced Cement Concrete 1:2:4, type B1 (using 20 mm graded stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

M&L for TMT bars of 10mm dia and over, cut to length, bent to shape as required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to soffit of suspended slabs such as lintel, roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

M&L flush pointing on brick/ concrete tiles in paving/ roofs, laid flat, in CM 1:3 including racking out joints/ pointing in floor/ roof and removal of all grass root small trees etc. complete all as specified and directed by Engineer-in-Charge.

Cutting down small trees/ bushes from wall/ roof/ chajja of building including digging out the roots from brick work or any other structure portion of building including applying root killer chemical as per manufacturer instructions and making good the disturbed portion to match the existing surface complete all as specified and directed by Engineer-in-Charge.

M&L for preparation and cleaning surfaces of concrete including flashing and junction of parapets etc and applying APP based polymeric membrane of weight minimum 3 kg/ sqm and minimum 3 mm thick reinforced with non-woven fabric with torch application over and including a coat of hot bituminous primer and finally applying one coat of silver aluminium paint over APP membrane including taking down old APP complete all as specified and directed by Engineer-in-Charge.

M&L Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/ floor including taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) bend, Tees 110 mm bore fixed as in repair complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced ) in ground floor and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-charge.

Providing and injecting chemical emulsion for Post Constructional Anti termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed by Engineer-in-charge.

Providing and injecting chemical emulsion for Post Constructional Anti termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by Engineer-in-charge.

M&L for cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, water trought and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by Engineer-in-charge.

M&L for 50 mm thick PCC 1:3:6, Type C-2 (using 40 mm graded stone aggregates) as in plinth protection etc finishing even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:4:8, Type D-2 (using 40 mm graded stone aggregates) as in foundations, filling and mass concrete etc complete all as specified and as directed by Engineer-in-charge.

Material and labour for factory made, Machine pressed precast concrete interlocking paver block, confirming to IS 15658-2006 of 40 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed by Engineer-in-charge.

Material and labour for factory made, Machine pressed precast concrete interlocking paver block, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed by Engineer-in-charge.

Note for BOQ serial Item No 51.00 to 52.00: 1. The shape/ size of paver blocks shall be as approved by the GE. 2. sand cushioning will be measured and paid separately under respective item here-in-after.

Supply and fixing of factory made rubber moulded machine pressed coloured chequered cement concrete tiles of size 300mm x 300mm x 25mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid over and including 15 mm thick screed bed in cement mortar 1:6, complete complete all as specified and directed by Engineer-in-charge.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description not exceeding 1 Sqm each and removing from site complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each and removing from site complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frame with shutters not exceeding 1.5 Sqm (without taking off shutters from the frame) and removal from site complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frame with shutters exc 1.5 Sqm but n.exc 4 Sqm (without taking off shutters from the frame) and removal from site complete all as specified and directed by Engineer-in-charge.

S&F Factory made box type steel window with side hung shutters with pintle hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, 2 Nos steel handle, 2 Nos steel pegs and with glazing bars, including flat iron 50 x 6 mm for cover gaps dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made box type steel ventilators including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete without glazing bars devetailed or welded fixed complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with M.S. Square tube, & fixing in opening as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

M&L Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, and fixing in frame at site as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

M&L 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge.

Cutting holes through brick wall built in cement mortar, for inserting holdfasts, depth of embedded portion of holdfasts exceeding half brick thick but not exceeding one brick thick and making good the dismantled portion with cement mortar (1:3) or PCC 1:2:4, type B-0 to match the disturbed surface with existing finish, complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hard wood, plain, solid, straight chowkhats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed by Engineer-in-Charge.

S&F pressed steel frame for doors with single rebates of size 105 x 60 mm made with steel sheet of 1.25 mm thickness in and including necessary fixing lugs, hinges, lock strike plate complete all as specified and directed by Engineer-in-Charge.

S&F pressed steel frame for doors with single rebates of size 165 x 60 mm made with steel sheet of 1.25 mm thickness in and including necessary fixing lugs, hinges, lock strike plate complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:3:6, type C-1 (Using 20 mm graded stone aggregates) as in pressed steel door frame (backfill) complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood glazed and skleton shutter, open rebated and prepared to receive glass, gauge etc (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a), complete all as specified and directed by Engineer-in-charge. NOTE : Wire gauge shutter should also have the provision of vertical member of size 75mm x 35mm at middle of the shutter. The vertical member have mitred joints and shall be stuck tenoned to the depth not less than 35 mm in top, lock & bottom rails and have rebate to receive the wire gauge etc. complete all as specified & directed by Engr-in-charge. (NOTE: Single Shutter)

S&F 2nd class hard wood factory made 35 mm thick paneled door shutter (two pannel) factory made with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, the size of rail and style as per IS 1003 (part-I) kiln seasoned and chemically treated complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hard wood 35 mm thick, factory made partly panelled and partly skeleton shutters, open rebated and prepared to receive wire gauze etc, edge of framing shall be plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc., complete all as specified and directed by Engineer-in-Charge.

S&F for 35 mm thick 2nd class hard wood plain, framed Flush shutters, solid core construction with block boards core and plywood face panels, commercial type on both sides) complete all as specified and directed by Engineer-in-Charge.

S&F in repair butt hinges, 100 mm length, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F handles, fabricated type, of 150 mm length, extruded aluminium alloy, anodized, complete all as specified and directed by Engineer-in-charge.

S&F Aluminium anodized barrel tower bolt 150 mm long of extruded section complete all as specified and directed by Engineer-in-charge.

S&F Aluminium anodized barrel tower bolt 200 mm long of extruded section complete all as specified and directed by Engineer-in-charge.

S&F in repair 300 mm long Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed etc complete all as specified and directed by Engineer-in-charge.

S&F 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate fixed as in repair complete all as specified and directed by Engineer-in-charge.

Supply & fixing in repair of floor door stopper of aluminium alloy body and tongue anodised, with hard drawn steel spring fixed in floor overall length of cover plate 140 mm etc complete all as specified and directed by Engineer-in-charge.

S&F Aluminium powder coated door seal strip with glass wool, having length 0.85 to 1.10 metre, fixed with steel screws at bottom rail of external door complete all as specified and directed by Engineer-in-charge.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Note:- (i) Thickness of powder coatings shall be not less than 50 micron. (ii) Weight of the aluminium sections only shall be measured and paid. (iii) Aluminium doors window/ ventilators to be fixed to jambs with cadmium plate screws. (iv) The rate shall be inclusive of neoprene beadings, handles, hinges, screws etc. weight of fittings/ fixtures will not be measured for ariving the weight of aluminium section. (v) Glass panes and panels shall be measured & paid separately under respective items.

M&L for Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing minimum 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified all complete as per architectural drawings and the directions of Engineer-in-Charge.

Hacking out old broken glass (any thickness) size quality etc from any type of frame fixed with pin, beading or oil putty complete all as specified and directed by Engineer-in-charge.

Supply and fixing 4 mm thick sheet glass, ordinary quality/ tinted, any size and in any type of frame and glazing with oil putty (or beading) in square not exceeding 0.5 Sqm in each panes complete all as specified and directed by Engineer-in-charge.

Supply and fixing 4 mm thick figured glass, pin head type, ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square not exceeding 0.5 Sqm in each panes complete all as specified and directed by Engineer-in-charge.

Supply and fixing galvanized MS wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, fixed complete all as specified and directed by Engineer-in-charge.

Supply and fixing galvanized MS wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, fixed as in repairs complete all as specified and directed by Engineer-in-charge.

Material and Labour for 20 mm dia Mild Steel, PVC coated, coloured, drapery rod including brackets, holder, endo brackets etc fixed as in repair, complete all as specified and directed by Engineer-in-charge.

Material and Labour for 20 mm dia Stainless steel drapery rod including brackets, holder, endo brackets etc fixed as in repair, complete all as specified and directed by Engineer-in-charge.

S&F in repair mortice lock, vertical type, size 100 mm, brass, 4 lever complete all as specified and directed by Engineer-in-charge.

Material and labour for Block Board 18/ 19 mm thick, grade 2nd quality, interior grade, commercial type fixed with screws to timber frame work as in cup board, kitchen cabinet, cupboard racks, wardrobe fitted to chowkhats, with 6 mm thick IInd class hard wood edging on exposed edges, complete all as specified and directed by Engineer-in-charge.

S&F 0.9 mm thick Decorative laminate, type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed by Engineer-in-charge.

S&F in repairs 18/ 19 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorativce choice laminations, fixed with screws to timber frame as in cupboards, shutters, shelves, cabinets, pelmets etc including fixing 18 mm wide 6 mm thick painted beading all around of 1st class HW (Teak) complete all as specified and as directed by Engineer-in-charge.

Providing and fixing 18 mm thick SOLID PVC DOOR SHUTTER made out of 18 mm Celuka Printed and UV Coted sheet which is cut according to the size of the cabinet or for Kitchen Drawer provided and the groove to be made on the one edge so that the overlapping could be done for double leaf door shutterfixwd in repair with 1.25” M.S. Screw to the frame with the channel hinge/ clip hinge. including Handles, which are to be provided from outside of door completeas per manufacturer’s specification & drawing and Directions of the Engineer-in-Charge.

S&F continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, with 30 mm width of flaps when open complete all as specified and as directed by Engineer-in-charge.

S&F stainless steel earl bihari semihydraulic hinges of size 175 mm, for cup board shutter, complete all as specified and directed by Engineer–in-Charge.

S&F in repair stainless steel tray/ trolley of various sizes for drawer to keep the kitchen utensil complete all as specified and directed by Engineer–in-Charge.

S&F in repair stainless steel telescopic channel normal, of 30 mm overall width and 450 mm length fixed in kitchen cabinets and the like complete all as specified and directed by Engineer–in-Charge. Make : Hafele or equivalent as approved by GE.

S&F 150 mm size hasp and staple, safety type, aluminium anodized, complete all as specified and directed by Engineer–in-Charge.

S&F in repairs Mild steel Cupboard Knobs, 40 mm dia fixed with nut, screws and washer complete all as specified and directed by Engineer–in-Charge.

S&F in repair magnetic catcher for kitchen cabinet and cupboards complete all as specified and directed by Engineer–in-Charge.

S&F in repair Stainless steel plate rack (utensil rack) of size (750 x 750 mm) and depth 250 mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/ bolts complete all as specified and as directed by Engineer–in-Charge.

M&L for welding in repairs exceeding 2.5 cm but not exceeding 5 cm in length, thickness of metal to be welded exceeding 6 mm but not exceeding 9 mm complete all as specified and directed by Engineer–in-Charge.

M&L for Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240, including one shop coat of zinc chrome red oxide primer including dismantling of old iron complete all as specified and directed by Engineer–in-Charge.

Dismantling of old Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed by Engineer–in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour, as approved by GE, having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer–in-Charge.

Material and labour for non-skid ceramic tiles, joint free, first quality, coloured size 300mm x 300mm x 7mm thick, as in floor, set and jointed with neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15 mm thick screed in cement mortar (1:6), including dismantling old floor tiles with bedding complete all as specified and directed by Engineer–in-Charge.

Material and labour for non skid, joint free, first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.11 sqm but n. exc. 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15 mm thick screed bed in cement mortar 1:6, including dismantling of old floor tiles with bedding complete all as specified and directed by Engineer–in-Charge.

M&L for First Quality, Glazed ceramic, coloured tiles 300mm x 200 mm x 7mm thick, in vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendering in cement mortar 1:4 on brick walls, including dismantling of old tiles complete all as specified and directed by Engineer–in-Charge.

Material and labour for glazed ceramic tiles in vertical surface 350mm x 450mm x 7mm thick or 300mm x 450mm x 7mm, joint free, first quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10 mm thick rendering in cement mortar 1:4,including dismantling of old tiles complete all as specified and directed by Engineer–in-Charge.

Material and labour for Vitrified Ceramic tiles 10 mm thick First quality (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement mortar 1:6 and including dismantling of old floor tiles with bedding complete all as specified and directed by Engineer–in-Charge.

Material and labour for 16-20 mm thick Granite stone slabs, best quality, machine cut and polished, to be fixed on kitchen platform, steps, pillars, floors etc., and jointed with grey cement slurry and pointed in white cement mixed with marble dust (1:2) with admixture of pigment to match the shade of slab, including rubbing and granite polishing over and including screed bed of 15 mm thick in cement mortar 1:6 and rounding off/ bull nosing exposed edges and making holes for gas pipes, including dismantling old stone complete all as specified and directed by Engineer–in-Charge.

M&L for Filling of white or coloured cement to match the colour of tile in hungry joints of glazed tiles not exceeding 1.0 RM each complete all as specified and directed by Engineer–in-Charge.

Supply and fixing in repair PVC bathroom mirror cabinet 500mm x 400 mm fixed with and including chromium plated brass screws and PVC rawl plugs, complete all as specified and directed by Engineer–in-Charge.

S&F in repair, rectangular sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed by Engr-In-Charge.

S&F in repair Aluminium anodized Peg set of six fixed with screws complete all as specified and directed by Engineer–in-Charge.

Supply and fixing in repair toilet paper holder, cast copper alloy, chromium plated fixed in position, complete all as specified and directed by Engineer–in-Charge.

S&F in repair Vitreous China wash hand basin, white, with pedastal, flat back, of size 550 x 400mm including brackets and waste coupling, complete all as specified and as directed by Engineer-in-charge.

S&F in repair Vitreous China wash hand basin, angle back, size 400 x 400 mm, white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and as directed by Engineer-in-charge.

S&F Waste coupling, brass, chromium plated (half or full threaded) 32 mm bore fixed in repairs complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair PVC waste pipe 32 mm dia complete all as specified and as directed by Engineer-in-charge.

S&F in repairs vitreous china counter top wash hand basin, white, of size 550 x 450 mm, mounted on granite stone slab platform, complete all as specified and directed by Engineer–in-Charge. Note : Granite platform, if required, shall be measured and paid separately

S&F in repair 32 mm bore brass chromium plated bottle trap for wash basin inlet and outlet screwed for pipe or connection including necessary packing union and cap complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever 03 nos brackets of angle 30mmx30mm ,thickness 3-4 mm,500 mm long with PCC 1:2:4, B-0 in wall and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by the Engineer-in-Charge.

S&F Grating doom 125 mm dia with or without waste hole of chromium plated fixed on floor/ nahani trap with cement mortar, fixed in repairs complete all as specified and directed by Engineer–in-Charge.

S&F in repairs stainless steel Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer–in-Charge.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white, (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed by Engineer–in-Charge.

S&F in repair Vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including 100 mm CI 'P' or 'S' trap set in and including concrete fixed in repair complete all as specified and directed by Engineer–in-Charge.

S&F in repair Vitreous China, semi-pedestal pattern (Anglo-Indian type) wash down water closet pan, white (including fixing bolts and flush pipe) complete all as specified and directed by Engineer–in-Charge.

S&F in repair Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/ off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (including fixing bolts & flush pipe) complete in all respect, complete all as specified and directed by Engineer–in-Charge.

S&F in repair Vitreous China wash down Single piece water closet pan (EWC), pedestal pattern, with integral flushing cistern, white (with all fittings) including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed by Engineer–in-Charge.

S&F 10 litre capacity virgin polypropylene flushing cistern, ISI marked, white, at low level complete with PVC bend/ flush pipe and making all connection including taking down existing high level/ low level cistern with all connections and making good the disturbed surfaces in cement mortar (1:3) to match with the existing surface,complete all as specified and directed by Engineer–in-Charge.

S&F in repairs Plastic water closet seat cover, white closed pattern with flat bottom and mild steel chromium plated hinging device, ISI marked, complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore Stop valves, fancy type, cast copper alloy, chromium plated, with long shank and Cup (Concealed Type), screwed down, high pressure with crutch both ends for iron pipes or for union and fixed complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore angle valves/ stop valve, fancy type, cast copper alloy, screwed down high pressure with crutch both ends for iron pipes or for union and fixed complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore Bib taps, long body, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore fixed complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore bib taps, PTMT, any colour, high pressure screwed for iron pipe with minimum weight 90 gms, complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore, brass, chromium plated, mixer for mixing Hot and Cold water, screwed down for iron pipes for wall mixture non telephonic complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore, brass, chromium plated, mixer for mixing Hot and Cold water screwesd down for iron pipes for telephonic wall mixture complete all as specified and directed by Engineer–in-Charge.

S&F in repair 15 mm bore, brass, chromium plated, mixer for mixing Hot and Cold water screwesd down for iron pipes for center hole WHB mixer complete all as specified and directed by Engineer–in-Charge.

S&F in repair Shower Rose, 125 mm size, Chromium plated with swivel joints, any size including fixing to steel pipes or union complete all as specified and directed by Engineer–in-Charge.

S&F in repair Tubular towel rack (single rack) stainless steel chromium plated 600 mm, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (Minimum weight 90gms) complete all as specified and as directed by Engineer-in-Charge.

S&F Tubular towel rail of brass chromium plated, 20mm dia, D type, 60 cm long between flanges, fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed by Engineer-in-charge.

S&F in repair Flushing jet spray for pedestal pattern W.C including flexible pipe and brass Chromium plated nuts, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair 15 mm dia PVC connection with PTMT nut, of length 450 mm, fixed complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair 450 mm Long Braided Hose with Two 15 mm Nuts & Rubber Washers Without Nipple (Suitable for Geysers) PVC connection pipe nozzle complete all as specified and directed by Engineer-in-charge.

S&F of corner glass shelf, Fancy type, of radius 300 mm with 300 x 600 mm size including 02 Nos. CP metallic holding brackets, railing etc. fixed with PVC rawl plugs and wooden screws, fixed in repairs, complete all as specified and directed by Engineer-in-charge.

Gunjan and Gunjan Associates (BID ID -3141430)

M/S Gupta and Sons (BID ID -3140860)

aggarwal contractors and engineers (BID ID -3138833)