WBPWD/SE/SWEC/NIQ36/2024-25

Amount

Supply & Errection of suitable size(dept 800 mm) out door type both side openning sheet steel piller box of 3.15 mm thick CRCA sheet with trapezium top cover (5mm thick) with ventillation arrangement with both side door arrangement hinged type , with mechanical locking arrangement and in built handle pcc and brick foundation of 20inch with plaster with net cement finishing etc. with central hollow with filling of fine sand at height of 4.5 feet from GL and below 1.5 ft on PCC (4inch thickness) on sand filling (6inch thickness) piller box should have two coat of synthetic enamel paint powder coat RO primer with mechanical locking arrangement, with pad lock arrangement also including providing of godrej brass make/ weather proof lock and key( 3nos Key with it including 2 no earthing terminalon it . the piller box should be two part type ( front and back side openning) with compressing of the folowing. The piller box should be provission for installation of WBSEDCL meter. A) Incommer: i) S&F 415 V, 63 A TPN SFU in Sheet steel enclosure with 3 nos HRC type fuse (Make: L&T/ Schneider/ Siemens) --1No ii) S& F of 415V, 63A , TP power contactor (Make: L&T/ Schneider/ Siemens) --1No iii) S&F of 24 hour analog time switch (Make: L&T/ Schneider/ Siemens) --1No iv) 5A troggle switch for bypass arrangement.

B) Busbar: 415V, 125A 4x15x3 mm copper bar as BBC in 16 SWG MS Sheet enclosure as per GS--1 set C) OUTGOING: i) 415V, 32 Amp TPN SFU in shhet steel enclosure with 3 nos HRC type fuse. make: (L&T,Schneider/ Siemens) ---3 nos D) Reading arrangement : i)0-500 V, 92mm x 92mm square typr digital voltmeter(L&T Make)--1no ii) 0-63 Amp 92mm x 92mm square type digital Ammeter (L&T Make) --1no iii) 63/5 Amp CT coil kappa make---3 nos iv) LED type indicating lamp(RYB)--3 nos v) 6amp TP MCB--1no vi) S&F of Danger board--1no

Supply & Fixing 240V of LED Street Light aerodynamically designed with excellent thermal management, made up of pressure die cast aluminium housing and toughened glass cover with IP66 protection, having high power LED's with peanut lens for better distribution along and across tbe road. Minimimim Lumen Output required 12,600 Lumen or higher. System efficacy should be equal or greater than 140 lumen per watt. Luminaires must have surge protection device of 4KV inbuilt with LED driver and lOKVexternal in the fitting and driver should be BIS approved silicon lilled potted driver for trouble free service life. Luminaire should be CCT-5700K, CR! > 70, THU><10%, PF >0.95 and min 50000 burning hours@,L70B50, having LM79, LM80 reports must be provided from NABL accredited Lab. Make of SMD type LED chip: Cree, Nichia, Osram, Lumileds. Luminaire should be engraved or embossed with manufacturer's logo and must have 5 year• warranty. (Make- Philips BRP502 LED126 CW R3C PSU S1/ Crompton/ Wipro/ Bajaj)

Supply & Delivery of 9 Mtr Steel Tubular Pole (Zindal /Bansal/ Utkarsh/Shubham pole/Tata) as per specification Type 410 SP -29 as overall length 9 mtr weight 125kg. & having diamention are : Out side dia & thickness of the Bottom section (139.7 x 4.85) mm; Middle;(114.3 x 4.50) mm ,Top Section (88.9 x 3.25) mm with fixing the base plate and GI earth bolt after making drilled holes etc. on pole incl. jacketing arrangement if reqd as per direction of EIC

Erection of Single Steel tubular pole of length as given below with/without sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly. Up to 9 mtr Size 0.6x0.6x1.70 mts

providing CC (6:3:1) base block (around the pole) dimension 0.60x0.60x0.76 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) incl. drilled hole in pole suitable for alkathene/ polythene pipe entry, for street light wiring, without Loop Box.

Supply & Fixing of 1.5 mtr long detachable type single arm bracket for pole SP-30/80 mm (ISI-M) pipe pole. The arm bracket shall be properly welded stifner plate of pole sleeve for strengthening including properly fixing arrangement with pole by nut-bolt, washer etc. as per direction of the EIC.

Supply & Fixing of 1.5 mtr long detachable type double arm bracket for pole SP-30/80 mm (ISI-M) pipe pole. The arm bracket shall be properly welded stifner plate of pole sleeve for strengthening including properly fixing arrangement with pole by nut-bolt, washer etc. as per direction of the EIC.

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one 4 way terminal, one compression type brass cable gland for upto 2/4- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint.

Supply & delivery of 1.1 KV, following size XLPE insulated 1100V grade as per IS 7098 (part-1) 1988 armoured sheathed Aluminium conductor cable as mentioned below. (Make- Polycab/Havells/GlosterI/RR Kabel )

4 Core 16 Sq. mm [Exsisting Panel to Feeder Pillar]

4 Core 10 Sq. mm [Feeder Pillar to Exsisting Pole Replaced for Damaged Cable]

Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below :

4 Core 10 Sq. mm

4 Core 16 Sq. mm

Finishing of the XLPE/PVC insulated armoured cable ends by soldering with cable sockets and insulated tapes etc., including supplying sockets, soldering materials, tapes etc.and making connection to switch, BDB and BBC etc.

4 Core 10 Sq. mm

4 Core 16 Sq. mm

Supplying and Drawing of 2 x 22/0.3 (1.5 sqmm) 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire incl 19mm bore PVC polythine pipe and making necy. connection as required)(Make- RR Kable/ Gloster/ Polycab/ Havells) (For disrtibution)

S & F of medium gauge G.I pipe (ISI medium) having the following diameter [32 mm Diameter] for protection of cable with necessary fitting and jointing materials as required.

Supplying and Drawing of 32 mm heavy gauge polythene pipe(Brand approved by EIC) and making necy. connection as required.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI medium GI pipe

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages. For solid 4 SWG GI wire.

Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Excavation of soil for installation of Earth Electrode and filling & ramming. (For morrum soil)

M S KAMAL SHAW (BID ID -5605691)

ELCON ENGINEERS (BID ID -5603932)