Providing roof slab retrofitting and additional repair works at Superintendent of Police Camp office cum Residence in Vellore District.

DW-B/S-CMW-U3) Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of Brick / Stone Masonry in cement mortar walls under 3m high including all tools and plants required etc. all complete as per relevant standard specifications and as directed by the departmental officers.

DM-FL-TI-CM) Removing the damaged existing floor finish & dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Clay Tiles / Cuddapah Slabs including all tools and plants required etc. all complete as per relevant standard specifications and as directed by the departmental officers.

DW-D-W-F) Removing the damaged Doors and Windows including removal of frames, hinges and fastenings including all accessories without affecting the adjacent structures including the hire charges for tools and plants and scaffolding if any and clearing the dismantled materials away from the site etc., all complete and as directed by the departmental officers.

CN-FB-PCC-1:5:10) Plain cement concrete 1:5:10 (One of cement, five of crushed stone sand and ten of hard broken stone Jelly including Mortar Plasticizer (Liquid) at 200ml per bag) for foundation and basement using 40 mm gauge hard broken stone jelly

BW-FB-KB-CM 1:5) Brick work in Cement Mortar 1:5 (One of cement and five of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) using Kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) in foundation and basement

BW-PW 114mm - FB-KB-CM 1:4) Brick partition wall in Cement Mortar 1:4 (One of cement and four of Crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 110mm thick for super structure in the following floors using Kiln burnt country bricks of size 8¾”x4¼”x2¾” (22x11x7cm) in the following floors a. In Foundation and Basement

CN-F&S-PCS-M20-20/40) Providing precast concrete slab for cupboard ward robes shelves, cover slab for chambers, Baffle walls side slabs of boxing around windows and other similar works in Standardised concrete mix M20 for the following thickness CN-SS-PCS-M20-20) I. 20mm thick CN-SS-PCS-M20-20-(GF) a. In Ground floor

CN-F&S-PCS-M20-20/40) Providing precast concrete slab for cupboard ward robes shelves, cover slab for chambers, Baffle walls side slabs of boxing around windows and other similar works in Standardised concrete mix M20 for the following thickness CN-F&S-PCS-M20-40) II. 40mm thick CN-SS-PCS-M20-40-(GF) b. In Ground floor

CN-F&S-RCC-M35) Providing and laying in position, Standardised Concrete Mix M-35 Grade (Using crushed stone sand) CN-SS-RCC-M35-(GF) b. In Stilt /Ground Floor

CN-SS-RCC-M35-(1F) c. In First Floor

PL-OU-CM 1:5-12mm) Plastering with CM 1:5 (One of cement and five of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 12mm thick

PL-IN-CM 1:4-12mm) Plastering with CM 1:4 (one of cement and four of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 12mm thick

FW-FW-WOS-RCC) Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below FW-SS-WS-PS) b.Plain surfaces such as Roof slab, floor slab, Beams, lintels, lofts, sill slab, staircase waist, portico slab and other similar works

RE-RTS-Fe-NC) Supplying, fabricating and placing in position of Mild steel Grills / Ribbed Tor Steels (without cement slurry) of all diameters for reinforcement for all floors including cost of binding wire, bending tying etc., all complete and as directed by the departmental officers.

Supply and fabrication of ISMB 600 x 210 x 12mm thick for Beam, ISMC 175 x 75 x 6mm thick for Purlins has to be fixed as per drawing. The rate is including transporatation and one coat of red oxide primer etc complete and as directed by the departmental offcers. a) ISMB 600 x 210 x 12mm

b) ISMB 3000 x 140 x 7.7mm

c) ISMC 175 x 75 x 6mm

Supply and fabrication of Base plate 400x 700x 20mm & Bold. Nut 400x 400x 16mm. The rate is including transporatation and one coat of red oxide primer etc., all complete and as directed by the departmental offcers.

Supplying and erecting Cup lock Joint Scaffolding Consists of a fixed bottom cup and a movable top cup. The ledger's forged blade is inserted into the bottom cup and then locked by sliding the top cup down over it. Integral Spigot: Allows standards to be connected vertically to one another. Holes: Holes in the spigot and at the base enable the use of locking pins to join standards. Surface Treatment: Common finishes include hot-dip galvanized, painted, or powder-coated for corrosion resistance etc., all complete and as directed by the departmental offcers.

Labour charges to perform the ARC or Stick welding with the welding thickness of no less than 8mm along with respective standard welding method. The rate shall be paid in Weight (Kg) basis, which shall include anchor fastener, bolt, nut, washer, packing plate, base plate etc., all complete and as directed by the departmental offcers.

Labour charges for fixing of ISMB & ISMC sections. The rate shall be paid in Weight (Kg) basis, which shall include anchor fastener, bolt, nut, washer, packing plate, base plate etc., all complete and as directed by the departmental offcers.

Supply and fabrication of MS square tube of size 70x70x3mm for rafters and size of 40x40x3mm for horizondal purlins including cost of labour charges for erection, fixing. transportation and one coat of red oxide primer etc., all complete and as directed by the departmental offcers.

Supply and fixing of Galvanium Roof sheet of 0.47mm thick including cost of all materials, cutting, welding & labour charges, fixing in position necessary screws, nuts, scaffolding etc.. all complete, as directed by the departmental officers. (The Material quality & brand should be got approved from the Executive Engineer before use)

MW-MS-GR) Supplying and fixing Mild Steel grills as per the design approved to verandah enclosure or gate including one coat of primer and labour for fixing in position etc. all complete

Clearing the dismantled debries from the site and Clearing the debries away from the site (24 KM) including loading, conveyance charges unloading labour charges etc all complete and as directed by the departmental officer.

Providing and filling the tile joint with epоху grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete.

TL-FL-IVT-CM 1:3) Supplying and fixing of Ivory colour Vitrified Tiles of size 600x600cmx8mm for flooring and other similar works (Best approved quality, colour and shade and the same shall be got approved from the Executive Engineer before use) in cement mortar 1:3 (one of cement and three of curshed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick

TL-FL-CDT-CM 1:3) Supply and laying superior variety Concrete Designer tiles for flooring in CM 1:3 (One of Cement and three of crushed stone sand including Mortar Plasticizer (Liquid) at 200ml per bag) 20mm thick

CN-Ellis-CM 1:3-BGC) Finishing the top of flooring with cement concrete 1:3 (One of cement and three of blue granite chips of size 10mm and below) 20 mm thick Ellispattern Flooring (No Sand)

EL-IN-AEP-AEP) Wiring with 1.5 sq.mm copper PVC insulated unsheathed single 1.1 KV grade core / cable with continuous earth by means of 1.5 sq.mm copper PVC insulated unsheathed single core 1.1 KV grade core / cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 g thick concealed and covered with 3 mm thick laminated hylem sheet for Administrative block and community center controlled by 5 amps flush type switch including circuit main, cost of all materials, specials etc., all complete and as directed by the departmental officer. a. Light Point with ceiling rose

b. Light Point without ceiling rose

EL-IN-AEP-SBI) Wiring with 1.5 sq.mm copper PVC insulated unsheathed single 1.1 KV grade core / cable with continuous earth by means of 1.5 sq.mm copper PVC insulated unsheathed single core 1.1 KV grade core / cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 g thick concealed and covered with 3 mm thick laminated hylem for Administrative block for 5 amps. 5 pin plug socket point at Switch Board Itself including circuit mains, cost of all materials, specials, etc., all complete

EL-IN-EP-CP) Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cablewith ISI mark conforming to IS: 694/1990, 1.1 K.v. grade cable with continuous earth by means of 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark conforming to IS: 694/1990, 1.1 k.v . grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 g thick concealed and covered with 3mm thick laminated hylem sheet for 5 amps. 5 pin plug socket point at convenient places including circuit mains, cost of all materials, specials, etc., all complete

Supply and fixing of 5 amps / 15 amps 3pin Flush type wall Socket including cost of material, labour charges for fixing with required screws , hire charges for tools and plants etc., all complete and as where required and as directed by the departmental officers. (The brand and quality of materials should be got approved from EE before use).

Supply and fixing of 20A Double pole plug and sockets in sheet steel enclosure with 32 amps DP MCB in flush with wall, with earth connection (for AC plug) of approved brand including cost of materials and labour charges etc., all complete as directed by the departmental officers. (The brand and quality should be got approved by the Executive Engineer before use)

EL-IN-WR-2x4m2) Run of main with 2 wires of 4 sq.mm. PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark conforming to IS: 694/1990,1.1 kv grade cable with continuous earth

EL-IN-WR-2x2.5m2) Run of main with 2 wires of 2.5 sq.mm. PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark conforming to IS: 694/1990,1.1 kv grade cable with continuous earth

EL-IN-LED.F-TL) Supply and fixing of 4' long 18 W Crystal Glass LED tube Light with ISI mark including cost of all materials twin core flex wire, TW round block and labour charges for fixing in position etc., all complete and as directed by the departmental officers (The material should be got approved from the Executive Engineer before use).

EL-IN-EF-9W) Supplying and fixing of 9 watts LED bulb of best quality including cost of material and fixing etc., all complete and as directed by the departmental officers. (The quality of the 9W LED bulb should be got approved from the executive engineer before use)

EL-IN-EF-ELCB) Supplying and fixing 40amps Earth leakage Circuit Breaker/Residual Current Circuit Breaker (ELCB/RCCB) 30 milli amps sensitive 6Ka breaking capacity with ISI marked single phase unit (IS 12640)

EL-V DB-8w MCB-63A,OW) Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63 A 4 P MCB as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only.

EL-IN-AEP-FP) Wiring with 1.5 sq.mm copper PVC insulated unsheathed single 1.1 KV grade core / cable with continuous earth by means of 1.5 sq.mm copper PVC insulated unsheathed single core 1.1 KV grade core / cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 g thick concealed and covered with 3 mm thick laminated hylem for FAN POINT sheet for Administrative block and community center controlled by 5 amps flush type switch including circuit main, cost of all materials, specials etc., all complete and as directed by the departmental officer.

Supplying of 4 feet Fan Down Rod for New ceiling fans including cost of delivery at site etc., all complete and as directed by the departmental officer.

EL-IN-EF-F) Supply and delivery of following Electric Ceiling fan with ISI mark with blades and double ball bearing, capacitor,etc., complete EL-IN-EF-48"F) a) 48" Electric fan 1200mm sweep

EL-IN-EF-AC) Charges for assembling and fixing of ceiling fan of different sweep with necessary connections and fixing of fan regulator on the existing board etc., all complete (Excluding cost of fan)

WS-EX-ASTM-PVC) Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D - 1785 of suitable schedule (40/60/80) of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/UPVC/GI specials/GM specials WS-EX-ASTM-32 PVC) a) 32mm dia

WS-EX-ASTM-25 PVC) b) 25mm dia

WS-EX-ASTM-20 PVC) c) 20mm dia

SA-IN-NT-PVC) Supplying and fixing of PVC Nahani Trap not less than 75mm 4 way / 2 way (Superior variety)

WS-EX-RWD-PVC) Supplying and fixing of following dia PVC SWR pipe with ISI mark conforming to IS 13952:1992- type `A` for Rain water down fall pipe with relevant specials WS-EX-RWD-110) b. 110mm dia PVC SWR pipe

SA-Ex-SWR P-Dia) Supplying and fixing the following dia PVC (SWR) pipe with ISI mark confirming to IS 13952:1992- type `B` for soil line with relevant specials confirming to IS 14735 SA-Ex-SWR P-110) a) 110mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

SA-Ex-SWR P-75) b) 75mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

Supplying and fixing Special type EWC superior variety (white) (Parryware, neycer etc) including cost and fixing including fittings such as CI brackets. Pvc connection GM wheel valve, Hex nipple, etc., complete (EWC and plastic cover shall be got approved from the Executive Engineer before fixing)

Supplying and fixing of Special type wash hand basin (white without pedastal), superior variety (Parryware, neycer etc) with all accessories such as powder coated cast iron brackets. 32mm dia C.P. waste coupling, Rubber plug and aluminium chain, 32mm dia B class G.1./ PVC waste pipe, Angle Valve, 15mm dia Nylon connection, 15mm dia Brass Nipples, 15mm C.P. pillar tap & required grating etc., complete in all respects (wash hand basin shall be got approved by the Executive Engineer before fixing).

Supplying and fixing of Special type 3 in 1 Wall mixer (Parryware, neycer etc) of Best quality including cost of tap with required specials and labour for fixing etc. all complete and as directed by the departmental officers.. (The quality and brand should be got approved from Executive Engineer before use)

Supplying and fixing of Special type Two way bib cock (Parryware, neycer etc) of Best quality including cost of tap with required specials and labour for fixing ete, all complete and as directed by the departmental officers., (The quality and brand should be got approved from Executive Engineer before use)

Supplying and fixing of Special type Angle cock (Parryware, neycer etc) with fittings of approved make (ISI) and quality including cost and labour charges for fixing etc.. all complete and as directed by the departmental officers. (The C.P water supply fittings should be got approved from the EE before fixing)

Supplying and fixing of Special type Pillar cock (Parryware, neycer etc) with fittings of approved make (ISI) and quality including cost and labour charges for fixing etc., all complete and as directed by the departmental officers. (The C.P water supply fittings should be got approved from the EE before fixing)

Supplying and fixing of Special type Galaxy over head Shower arm (Parryware, neycer etc) including cost of required specials and labour for fixing etc. all complete.

Supplying and fixing of Special type Stainless steel Health Faucet approved quality with ISI mark (Health Lacet shall be got approved from the E.E before use.) including all accessories etc. complete complying with relevant standard specifications and as directed by the departmental officers.

WS-IN/EX-GM GV) Supplying and fixing of following dia Gun Metal Specials as per IS Specifications including cost of all materials and fixing labour charges etc., all complete and as directed by the departmental officers. (The materials should be got approved from the Executive Engineer before use) WS-IN/EX-GM GV-25) c. 25mm dia

WS-IN/EX-GM GV-32) d. 32mm dia

JN-WR-TWF-WRF) Supplying and fixing of Teak Wood wrought and put up for frames of doors, windows, ventilators, cupboard and any other similar joinery works with necessary plugs, rebates for shutters, plaster grooves on all faces etc. , including labour charges for fixing hold fasts, complying with relevant standard specifications etc., in all respects. JN-WR-TWF-A 2m F) a. Teak wood over 2.00 metre and below 3 metre length

JN-WR-TWF-B 2m F) b. Teak wood below 2.00 metre length

JN-SC D-DL-FLS-2.4H) Supplying and fixing of Double leaf Solid core flush door shutters using boiled water resistance (BWR) teak wood ply as per IS 303-1989, the cross band and face veneers are to be banded with phenol formaldehyde synthetic resin in hot press both sides and manufacturing the shutter by using quality timber of termite proof and seasoned to moisture content not more than 10%, hot pressed with hydraulic press at a temperature of 150o to the norms as per IS 2002-1983 and TW Ply on Both side with teak wook lipping around, 35mm thick including cost and fixing of Aluminium furniture fittings such as 8 nos 5” butt hinges, 3 Nos 6'x1/2' Towerbolt, 4 Nos 6' Handle with CP screws, 1 No of 10'x5/8' Aldrop , 2 Nos 40mm dia & 60mm long rubber bush , 2 Nos Aluminium Door stopper with rubber bush,necessary Brass screws and labour charges for wrought and putup and fixing in position of flush shutters and painting the TW portion with two coats using varnish two coats and as directed by the departmental officers. (The quality and brand of materials should be got approved from the Executive Engineer before use.) JN-SC D-DL-FLS-1.2x2.1 b.1200mm x 2100mm

JN-SC D-SL-FLS-2.1H) Supplying and fixing of Single leaf Solid core flush door shutters using boiled water resistance (BWR) teak wood ply as per IS 303-1989, the cross band and face veneers are to be banded with phenol formaldehyde synthetic resin in hot press both sides and manufacturing the shutter by using quality timber of termite proof and seasoned to moisture content not more than 10%, hot pressed with hydraulic press at a temperature of 150o to the norms as per IS 2002-1983 and TW Ply on Both side with teak wook lipping around, 35mm thick including cost and fixing of Aluminium furniture fittings such as 3 nos 5” butt hinges, 2 Nos 6'x1/2' Tower bolt, 2 Nos 6' Handle with CP screws, 1 No of 10'x5/8' Aldrop, 1 No 40mm dia & 60mm long rubber bush , 1 No of Door stopper with rubber bush, Brass screws and labour charges for wrought and putup and fixing in position of flush shutters and painting the TW portion with two coats using varnish two coats and as directed by the departmental officers. (The quality and brand of materials should be got approved from the Executive Engineer before use.) JN-SC D-SL-FLS-0.9x2.1) b.900mm x 2100mm

supply and fixing of best indian teak wood double leaf panelled door shutter in position using 150mm x 40mm outer styles 4 nos, 100mm x 40mm intermediate styles 2 nos and using 150mm x 40mm top and bottom rail, 75mm x 40mm the for all intermediate rails and using teakwood plank of thickness of 40mm thick to suit the ornamental carving work including labour charges for ornamental carving work & for fixing the shutter in position with the necessary following brass futings 8" majestic brass door handle 4 nos 5" brass hinges 10 nos, 16 brass tower bolt 2 nos, 8" brass tower bolt 3 nos, 12" x 5/8" ornamental brass aldrop I no, rubber bush 2 nos, 6 brass door stopper-2 nos with brass screws. best approved quality and shade etc., all complete and as directed by the departmental officers. (the brass fittings should be got approved from the executive engineer before using), a) 1500 X 2400MM

JN-BWRD-SL-Ply-0.9x2.1) Supplying and fixing of Best Indian T.W. single leaf door shutters using 9mm thick phenol bonded BWR grade plywood as per IS 303-1989 (General) with IS 5539-1969 (for preservative treatment) and IS 848-1974 (for adhesives) with relevant IS specifications and its latest amendment for shutters with 75mm x 37.50 mm teak wood styles and 3 Nos. of 150 mm x 37.50 mm TW rails (top, bottom and lock rails) using the above panel including labour charges and cost of furniture fittings as per schedule 'E' and as directed by the departmental officers. (The quality of BWR plywood should be got approved from the Executive Engineer before use.) b) 900 x 2100 mm

JN-UPVC W-UPVC-OP W) UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the framesetc., all complete as per relevant standard specification and as directed by the departmental officer. The window should be got approved from the Executive Engineer before use on work

JN-WPC D-SL-D) Supply & Fixing of WPC Decora Door set where the Door shall be extruded as a single core door with Lead-Free compound and the surface shall have Decora Design i.e, Non-porous Smooth Routing and 3D embossed wooden bark grains on one side. The complete door must be homogeneously made to avoid any disfigurement in the appearance. The door shall be of minimum 25mm Thick and be 550 KG/Cu.Mtr of density, i.e 1.28 KG per sq. Feet. And The solid door frame extruded with size 75MM x 50MM with minimum Density 800 Kgs / Cub. Mtr. The door must be hinged with minimum of 3 Nos of 5 Inch Hinges and the frame shall be fixed onto the wall with a minimum of 4 Nos. of 8MM x 100MM long Fastener Screw fitted with polymeric nylon sleeve. The Door shall have all ISI hardware including 3 Towerbolt in front & back together, 2 Handles in either side etc. all complete in all respects as directed by the departmental officers. (The colour, brand and quality of window should be got approved from the Executive Engineer before use)

Supplying and fixing of country Wood planks upto 30cm wide 25mm thick in end supports to the mangalore roof and any other similar works including labour charges for fixing in position, complying with relevant standard specifications etc., all complete and as directed by the deprtmental officers.

PA-Ex-IW-2C EP) Painting the new Iron work and other similar works such as PVC /ASTM Pipes, Kerb Stone and grills with two coats of approved first class synthetic enamel ready mixed paint of approved quality and brand, the paint should be supplied by the contractor at his own cost.

PA-IN-WP-2C BPC) Painting the new wood work with two coats of approved first class synthetic enamel ready mixed paint in addition to one coat of primer of approved quality and shade, the paint should be supplied by the contractor at his own cost.

PA-IN-OWP-1C EP) Painting the old wood work with one coat of approved Ist class synthetic enamel paint including thorough scrapping the old paint using sand paper as required by the departmental officers including cost of material, labour for painting, supplying etc., all complete as directed by the departmental officers.

PA-IN-WP-2C) Supplying and applying of Full putty two coats with approved make wall putty for smooth finishing the old cement plastered walls including cost of putty, brushes, watering curing labour charges for apply putty, blade, scaffoldings etc., complete as directed by the departmental officers.

PA-IN-PEP-OW W P) Painting old walls two coats with ready mixed plastic emulsion paint of first class quality paint of approved colour and shade for outer wall and other similar works with priming coat through scrapping including cost of necessary brushes, labour charges, patty etc.,

PA-IN-PEP-2C BPC) Painting the false ceilling / New walls with two coats of 1st class ready mixed PLASTIC EMULSION PAINT of best approved quality colour and shade including a priming coat over cement plastered surface including clean removal of dirt and dust etc., complete including cost of necessary brushes, labour charges, putty etc., complying with relevant standard specification. (The paint should be supplied by the contractors at his own cost.The quality and shade of the paint should be got approved from the Executive Engineer before use.)

FW-SS-AHS-2leg) Providing two legged scaffolding using 15cm diameter casurina props or best quality bamboo posts of 4m overall length (3m height + 0.50m projection + 0.50m into the ground ) the distance between the two rows being 1.25 m and the spacing of posts being 2m in both rows with two horizontal posts with 0.5m overlap on either side and braces at 2mc/c including longitudinal and transverse middle braces to step up and providing a platform with country wood planks of 40mm thick and 1 m width etc., all complete firm using coir and nails 1m run. FW-SS-AHS-5.5m) b).5.50 m height in addition of 2.5m ht

Please Enable Macros to View BoQ information