SPECIAL Repair to khanna khamano Road to LC Road including phirni Village Farour and JNV Schoo approach and lc road Manderan to railway station Khammano Falling in MC khamano District Fatehgarh Sahib (Left over Rural Link Roads Under SR Programme l

Making 50 mm x 50 mm furrows 45 degree to the center line of the road and at one metre interval in the existing bituminous wearing coarse including sweeping and disposal of excavated material within 1000 metres lead complete as per technical clause 404 of MORT&H specifications (Full surface area will be measured for payment) complete in all respects

Dismantling of existing road crust containing stone pitching or soiling. (50 mm to 150 mm thick).

Dismantaling of brick work /tile masonary or tile lining. (i) Dismantaling of dry brick work

Brick on End Edging Providing and laying of brick on end edging 6.83 cm wide, 11.11cm long and 22.86 high half brick deep including excavation, refilling and disposal of surplus earth up to 50 mtr complete as per Punjab PWD specifications.

Relaying of recovered material obtained from dismantled road material obtained from road crust compacting with vibratory roller to achieve the desired density, complete as per MORD technical specifications

Compaction of earth work and preperation of sub grade including loosening leveling of earth 225 mm thich top layer rough dressing of soil final dressing of earth to give level camberwatering rolling with road rollercompacting the bed to achieve minimum dry density as given in Table 300-2 as per technical clause 305 of MORT&H specifications (In case of link roads earthwork to be done by villagers)

Construction of granular sub-base by providing material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per MORD technical specifications

Water Bound Macadam Grading I (without screening for low volume Roads/undersigned Providing, laying, spreading and compacting stone aggregates of Grading I to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications

Water Bound Macadam Grading II (without screening for low volume Roads/undersigned Roads Providing, laying, spreading and compacting stone aggregates of Grading II to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications

Providing and laying patch work with stone aggregates of Grading II laid to water bound macadam specification after trimming the pot hole, removal of failed material, hand packing, applying and brooming requisite type of binding materials to fill up the interstices of coarse aggregate, watering and rolling with smooth wheeled roller 8-10 tonnes to match the adjoining surface complete as per technical clause 404 of MORT&H specifications (Without Screening)

Surface Dressing Providing and laying surface dressing in single coat using crushed stone aggregates of specified size on a layer of bituminous binder VG-10 @ 1kg per sqm laid on prepared surface after cleaning the road surface and rolling with 8-10 tonne smooth wheeled steel roller complete as per technical clause 509 of MORT&H specifications

Tack coat with Bitumen VG-10 Providing and applying tack coat with penetration grade bitumen VG-10 using bitumen pressure distributor at the rate of 0.40 kg per sqm on the prepared bituminous surface/granular surface treated with prime coat after cleaning the surface complete as per technical specifications

Open - graded premix Providing, laying and compaction of open - graded premix surfacing of 20 mm thickness consisting of crushed stone aggregates of specified grading premixed in a Continuous type hot mix plant with bituminous binder VG-10 @ 1.46kg per sqm, laid with Paver Finisher Mechanical and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades complete as per technical clause 510 of MORT&H specifications

Open - Graded Premix with Plastic Waste

Seal coat Providing and laying of premix sand seal coat premixed in Continuous type hot mix plant using specified fine aggregates and penetration grade bitumen VG-10 @ 0.68kg per sqm, laid to the specified levels, grade and cross fall complete as per technical clause 511 of MORT&H specifications

Cement concrete 1:6:12 With stone aggregates 20mm gauge mixing by mechanical means using concrete mixer volumetric type

Providing and laying factory made rubber moulded smooth finish cement concrete Kerb M-20 grade 250mm high with bottom width 165mm and top width 115mm made over strong vibratory table and fixing with cement mortar 1:2 as per MORT&H specifications

Providing and laying 60 mm thick factory madecement concrete interlocking Paving blocks of M-35 grade manufactured by block makingmachine equipped with steel mould clamped to astrong vibratory table with hydraulic pressure forcompaction of concrete as per IRC SP 63 -2014and of approved size and design / shape laid inOrdinary Grey Colour and pattern over andincluding 40 mm thick compacted bed of coarsesand, filling the joints with fine sand etc, allcomplete as per directions of Engineer-in-Charge

Earth work undressed Kassi work undressed involving an average horizontal throw up to 2 metres and average vertical lift up to 0.5 metres

Providing and making rumble strips 15-20mm high at centre, 250mm wide placed at 1m centre to centre over freshly laid bituminous layer by using close graded premix surfacing material type B at approved locations to control speed. The close graded premix surfacing material type B shall conform to technical clause 512 of MORT&H specifications

Repair of Safety parapet wall 2 mtr Each Block complete in all respect & as per directons of Engineer-in - Charge

Road Marking with Thermoplastic Compound Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications

Moulded Shank Road Stud Supplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications.

(i) Brick Bat

(ii) Bricks

Add Culture Cess @ 1%

Maintenance Work

Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 2nd Year)

Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 3rd Year)

Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 4th Year)

Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 5th Year)

Add Culture Cess @ 1%