PROVISION OF CERTAIN NEW IGLOO SHEDS UNDER GE AF GURGAON NO 1

Amount

Blank

Blank

Blank

Blank

Blank

Blank

Blank

SCH 'A' PART IX (MISC B/R & E/M ITEMS) Note:- Excavation and earthwork to the extent required for execution of relevant item under this schedule unless otherwise specified shall be measured and paid under relevant items of Schedule 'A' Part-II.

INTERNAL ELECTRIFICATION

Material and labour for sub main wiring with 2 runs of 4 Sqmm as main cable and one run of 4 sqmm as earth continuity conductor on wall and surface wiring on ceiling / roof with necessary fixing arrangements using approved colour coding as per IS with single core PVC insulated unsheathed FRLS cable of specified size multistranded copper conductor 1100 volts grade, IS-694 marked, drawn through ISI Marked (IS 9537 Part II) ERW stove enamelled rigid steel conduit suitable for wiring, not less than 20mm dia with all MS conduit accessories/ fittings such as bends, tee, elbow etc., and making good the disturbed surface complete all as specified and as directed.

Notes : (i) Rates of flame proof junction boxes, flame proof unions and couplings, rotary switch shall be measured and paid separately. (ii) One rotary switch shall control 2 to 4 Nos FP Points fitting. (iii) 3 runs of 4 sqmm cable and 1 run of conduit shall be measured as 1 unit . (iv) Rates of flame proof bends and elbows, couplers, bell mouth reducer etc. shall be deemed to be included in the rate quoted.

Supply and fix flame proof and weather proof switch rotary type with termination box in LM6, 16 A, single pole, 250 V suitable for hazardous locations of Zone 1 & 2, Ex 'd' with relevant IS & IP65 protection complete all as specified and as directed.

Supply and fixing surface mounted flame proof junction box 3 to 4 way 20 mm minimum all as per relevant IS for flame proof sub main wiring complete all as specified and as directed.

Supply and fixing surface mounted flame proof union (male, female type) dia 20 mm minimum all as per relevant IS for flame proof sub main wiring complete all as specified and as directed.

Supply and fixing flame proof coupling dia 20 mm all as per relevant IS for the flame proof sub main wiring complete all as specified and as directed.

Supply and fixing CMRI certified LED flame proof well glass luminaries 60 Watt with LM6 aluminium alloy lamp housing heat resistant and toughened glass, cover hinges cover with neoprene gasket, painted MS bar guard, epoxy finish provided with built in control gear box complete with all accessories internally prewired & eye bolt for suspension, IP 65 protection and including fixing light fitting on wall/roof and making all electrical connection complete all as specified and as directed.

Supply and fixing LED 60 W flame proof bulk head light fitting properly earthed suitable for hazardous locations of Zone 1 & 2 Ex 'd' with relevant IS & IP65 protection complete with all mounting attachments complete all as specified and as directed.

Material and labour for earthing with galvanized iron earth plate of size 600 mmx600mmx6mm thick buried directly in ground not less than 2.25 mtr below normal ground level, earth plate packed on all side with charcoal mixed with salt to a thickness of 150 mm connected by GI wire 4 mm dia at two points soldered and riveted to earth plate, GI earth wire protected by using 20 mm bore light grade GI pipe, watering pipe GI 20 mm dia medium grade 2.5 mtr long with funnel, wire mesh etc. necessary earth/brick work and PCC work, disposal of surplus soil to a distance not less than 50 metre, chamber of PCC (1:4:8) type D2 using 40 mm graded stone aggregate, coping in PCC (1:3:6) type C1 using 20 mm graded stone aggregate,

RCC pit cover 50 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate, reinforced with 8 mm MS bar at 80 mm C/C both way, flame funnel wire mesh, testing on completion all as specified and as shown in electrical plate No 3 of MES SSR Part-1 2009 complete all specified and as directed. Note:- Quantity of GI earth wire & protection pipe beyond 7.5mtrs length shall be measured and paid separately.

Supply and fixing weather proof distribution board approved by CMRI Dhanbad of cast aluminium alloy LM6 MCB type SPN 8 way with and including 32 Amps SPN MCB as incoming - 01 No with rotary switch and MCB SP 'C' series 10 KA 6-32 Amps - 6 Nos with rotary switch as outgoings complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

Supply and laying old size fly ash bricks in trenches for cable protection complete all as specified and as directed.

Supply and fixing 4 pole MCCB 63 Amps, 50 Hz, 415 Volts, rupturing capacity 25 KA complete all as specified and as directed.

Supply, installing, testing and commissioning of LT panel, double door, outdoor type floor mounted, factory made, powder coated made out of outside body of CRCA sheet 3 mm thick and inside body 14 gauge steel sheet, locking arrangement, front side and rear side opening arrangement, LT panel of size 1.0 m x 1.0 m x 0.6 m including mounting on angle iron stand of section 50 x 50 x 6 mm having minimum height 1.0 feet duly grouted or welded on floor, aluminium bus bars TPN of 200 A for MCCB to all feeders complete all as specified and as directed and comprising of following equipments/fitments complete :-

Material and labour for earthing complete with GI mild steel earth plate electrode 600mm X 600mm X 6 mm thick, burried directly in ground veritcally (Earth pit not less than 2.25 metre deep below ground level) with top edge of the earth plate not less than 1.5 metres below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and earth plate connected to GI strip of size 32 x 6 mm by means of bolts, nuts, check nuts and washers of steel and riveted to earth plate at one end and connected to metallic bodies of equipment etc. at other end, earth strip encased in and

including 40mm bore GI light grade pipe with all fitting from top of electrode to the body of equipment fixed with and including 25 x 4mm flat iron clamps, bolts, nuts and washer and also including GI pipe 20 mm light grade for watering from bottom of earth pit to top of electrode including GI funnel with wire mesh all as shown in electrical plate No. 3 including PCC pit (1:3:6) type C1 in cement concrete 40mm thick precast RCC cover in (1:2:4) type B1 reinforced with 8mm dia TMT bars @ 75 c/c both ways with 01 No lifting handle of 12mm dia MS plain bar, etc. complete all as specified and as directed. NOTES : (i) Quantity of GI strip/ protection pipe beyond 7.5mtrs length shall be measured and paid separately.

Material and labour for earthing complete with copper plate electrode 600mm X 600mm X 3.15 mm thick, burried directly in ground veritcally (Earth pit not less than 2.25 metre deep below ground level) with top edge of the earth plate not less than 1.5 metres below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and earth plate connected to copper strip 20 x 3 mm as earthing lead by means of bolts, nuts, check nuts and washers of steel and riveted to earth plate at one end and connected to metallic bodies of equipment etc. at other end, earth strip encased in and

including 40mm bore GI light grade pipe with all fitting from top of electrode to the body of equipment fixed with and including 25 x 4mm flat iron clamps, bolts, nuts and washer and also including GI pipe 20 mm light grade for watering from bottom of earth pit to top of electrode including GI funnel with wire mesh all as shown in electrical plate No. 3 including PCC pit (1:3:6) type C1 in cement concrete 40mm thick precast RCC cover in (1:2:4) type B1 reinforced with 8mm dia TMT bars @ 75 c/c both ways with 01 No lifting handle of 12mm dia MS plain bar, etc. complete all as specified and as directed. NOTES : (i) Quantity of GI strip/ protection pipe beyond 7.5mtrs length shall be measured and paid separately.

LIGHTENING PROTECTION

Supply and fixing ready made type PVC junction box IP65 of size 200 mm x 160 mm x 98 mm having shutter and lefting knob with provision of earthing strip entry glands and fixing the box on wall/poles with suitable size of clamps, nuts, bolts and washers etc. complete all as specified and as directed.

Supply, erection in true vertical position and fixing of steel tubular LT poles, swaged, welded complete with Cl base plate 6mm thick of size 300mm X 300 mm, finial taper plug pole cap, bolt and nuts and screw as per IS-2713 (Pt-II) made out of ERW MS Tubing with including drilling of hole of required size & Nos for fixing cross arms & 02 Nos hole on bottom and top of pole for insertion of cable including painting with two coat of aluminum paint over one coat of primer for exposed surface and two coat of bituminous paint for embedded portion in concrete, painting three blue bands at lower portion of pole 300 mm height at 300 mm spacing. painting pole No with black paint at suitable height complete of type 410 SP- 73 (14.5 mtr long) all as specified and as directed.

EXTERNAL WATER SUPPLY

Supply, laying, jointing and testing of ductile iron pipe spigot and socket including specials, class K-9, 100 mm bore complete all as specified and as directed.

Total amount of Schedule 'A' Part IX carried over to General Summary

Blank

Blank

GENERAL SUMMARY

Lumpsum price worked out by the contractor for “BUILDINGS & STRUCTURES” as listed in Schedule ‘A' Part I representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part I on Srl Page No. 34(R)

Lumpsum price worked out by the contractor for “SITE CLEARANCE, EXCAVATION AND EARTH WORK (FOR SCHEDULES OTHER THAN SCHEDULE 'A' PART-I)” as listed in Schedule ‘A' Part II representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part II on Srl Page No. 37(R)

Lumpsum price worked out by the contractor for “DUNNAGE” as listed in Schedule ‘A' Part III representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part III on Srl Page No. 39

Lumpsum price worked out by the contractor for “ROAD/ PATH/ CULVERT” as listed in Schedule ‘A' Part IV representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part IV on Srl Page No. 45

Lumpsum price worked out by the contractor for “AREA DRAINAGE” as listed in Schedule ‘A' Part V representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part V on Srl Page No. 48

Lumpsum price worked out by the contractor for “EXTERNAL WATER SUPPLY” as listed in Schedule ‘A' Part VI representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VI on Srl Page No. 50

Lumpsum price worked out by the contractor for “EXTERNAL ELECTRIFICATION & EQUIPMENT EARTHING” as listed in Schedule ‘A' Part VII above/below the lumpsum price as inserted by MES for Schedule ‘A’ Part VII on Srl Page No. 52(R)

Lumpsum price worked out by the contractor for “LIGHTENING PROTECTION” as listed in Schedule ‘A' Part VIII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VIII on Srl Page No. 56(R)

Total amount of SCHEDULE 'A' PART IX (MISC B/R & E/M ITEMS) brought forwarded from Serial Page No. 66(R)

Aalaya Engineering Project Private Limited (BID ID -3066647)

AMIT ASSOCIATES (BID ID -3074084)

M/s Arihant Builders (BID ID -3074471)

B D Raizada Projects Pvt Ltd (BID ID -3074301)