REPAIR MAINT OF MOTOR AND PUMP SETS OF WATER SUPPLY INSTALLATIONS AND OTHER EM WORKS AT WATER SUPPLY INSTALLATION AT AF STATION SURATGARH

Amount

BOQ (REPAIR/MAINT OF MOTOR AND PUMP SETS OF WATER SUPPLY INSTALLATIONS AND OTHER E/M WORKS AT WATER SUPPLY INSTALLATION AT AF STATION SURATGARH)

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 25 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 2 here-in-after and repair of parts as per item No 3 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.1 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing 6312.Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump required under item No 01 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 35/40 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 5 here-in-after and repair of parts as per item No 6 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.4 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 04 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 7.5/10 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 2 here-in-after and repair of parts as per item No 3 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No. 7 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 07 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 20 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 2 here-in-after and repair of parts as per item No 3 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No. 10 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 10 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting & dismantling the defective three phase induction motor squirrel cage of any make and of capacity 3 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : (a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

All as per srl item No.13 here-in-before but motor of capacity 5 HP.

All as per srl item No.13 here-in-before but motor of cap 7.5 HP.

All as per srl item No.13 here-in-before but motor of capacity 10 HP.

All as per srl item No.13 here-in-before but motor of capacity 20 HP.

All as per srl item No.13 here-in-before but motor of capacity 25 HP.

All as per description of serial item No.13 here-in-before but motor of capacity 30 HP.

All as per description of serial item No.13 here-in-before but motor of capacity 35 HP.

All as per description of serial item No.13 here-in-before but motor of capacity 40 HP.

All as per description of serial item No.13 here-in-before but motor of capacity 75 HP.

Dismantling/taking out defective submersible pump set of capacity 15 HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Rewinding of defective submersible motor of 15 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional complete all as directed.

Supply only spare parts as under required in Srl item No.30 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

REPAIR TO PARTS OF SUBMERSIBLE PUMP SET reqired under item No-30 above:-

Straightening of pump shaft by re-meting welding.grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush Fixing.

Dismantling/taking out defective submersible pump set of capacity 7.5HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed by Enginer-in-charge. Note : Spare parts & repairs as required will be measured and paid seperately.

Rewinding of defective submersible motor of 7.5 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional complete all as directed Enginer-in-charge.

Supply only spare parts as under required in Srl item No.36 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

REPAIR TO PARTS OF SUBMERSIBLE PUMP SET reqired under item No-36 above:-

Straightening of pump shaft by re-meting welding.grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush fixing.

Dismantling/taking out defective submersible pump set of capacity 5HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed. Note : Spare parts & repairs as required will be measured and paid seperately

Rewinding of defective submersible motor of 5 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional complete all as directed.

Supply only spare parts as under required in Srl item No.39 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

REPAIR TO PARTS OF SUBMERSIBLE PUMP SET reqired under item No-39 above:-

Straightening of pump shaft by re-meting welding.grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush Fixing.

Taking up CI/DI/GI water mains 80 mm dia from trenches (including all fittings), with spigot and socket ends and lead/tyton joints including burning out joints and recovering lead complete all as specified and directed. (Note : Earthwork to be measured and paid seperately)

All as per serial item No-35 here-in-before but size100 mm bore

All as per serial item No-35 here-in-before but size150 mm bore

Taking up or down steel tubing of size 20 mm bore including all fittings and connections complete all as specified and directed by Engr-in-charge.

All as per serial item No-38 here-in-before but size 25 mm bore

All as per serial item No-38 here-in-before but size 40/50 mm bore Note:- Earth work weather required shall be measured and paid separetaly.)

Dductile Iron pipes of 80mm bore with Spigot and socketed ends, Class “K-9”, suitable for and including rubber tyton joints complete all as specified. Make: Electro steel/Jindal

Dductile Iron pipes of 100mm bore with Spigot and socketed ends, Class “K-9”, suitable for and including rubber tyton joints complete all as specified. Make: Electro steel/Jindal

All as per serial item No-42 here-in-before but size150 mm bore

Galvanised Tube 20mm bore, 'Medium grade', with all fitting including cutting, threading etc as per site requirement and drilling holes/fixing clamp set for taking branch connection from main pipe line & fixed on walls or laid under floors complete all as specified and directed. Note :for laying under road using welding of pipe line with flanges/sockets as per site requirment is included in this quoted rate.

All as per serial item No-44 here-in-before but size 25 mm bore laid in trenches

All as per serial item No-44 here-in-before but size 40 mm bore laid in trenches

All as per serial item No-44 here-in-before but size 50 mm bore laid in trenches

Excavation in trenches loose/soft soil not .exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for foundations, laying water mains, pipes, cables, etc getting out and formaing bottom surface to required gradient complete all as specified .

Returing filling in incl spreading leveling, watering and well ramming in layer not less than 25 cm each layer complete all as specified and directed.

Removing excavated material to a distance not exc 50M and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified

Gun-metal gate valves with iron wheel head, screwed both ends size 20 mm bore, for iron pipe including taking down old/unserviceable valve complete all as specified and directed.

All as per serial item No-51 here-in-before but size 25 mm dia bore

All as per serial item No-51 here-in-before but size40 mm dia bore

All as per serial item No-51 here-in-before but size 50 mm dia bore

Material and labour for Cast Iron/Ductile iron fittings for spigot and socket pipes up to 200 mm bore such as bends (any type, radius and angle) tapers, any type (straight bend increasing, decreasing or double socket etc) Tee pieces, single branch ‘Y’ junction double branch, cross collars caps and plug, and "D" joint complete all as specified and directed by Engineer-in-Charge. Note: Earth work will be measured and paid seperately for fixing of "D" joint in unserviceable/broken line.

Material and labour for cutting of road ,cutting chases pining in making good to facing where required to edges of landing road,hard standing,etc,and cutting chases for concealed water tubing making good exc 20 cm but not exc 60 cm width and digging of excavation40 cm but not exc 1m depth in bituminous road /concrete surface and making good as existing surface by using 0.63 mm hard core as required including premixed high performance cold mix patching material ideal for instant as require high quality repairs to bituminous as well as concrete surface all as directed by Engineer in Charge

Demolition of brick work or stone/boulder masonary built in cement mortar including all quions arches pillars etc, but excluding ashlar facings dressed stone work and precast concrete articles

M&L for brickwork with subclass B bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and as directed.

Taking up existing DI pipe line of size 80 mm removing old unserviceable Tyton joint (push-on-joint) and supply , fixing and testing of Tyton joint (push-on-joint) and relaying the pipe line completely complete all as specified and as directed. Note : 1.Earth work paid seperately 2.Incase of pipe line is broken for takingup time new existing size of pipe line is laying by contractor in this quoted rate

Taking up existing DI pipe line of size 100 mm removing old unserviceable Tyton joint (push-on-joint) and supply , fixing and testing of Tyton joint (push-on-joint) and relaying the pipe line completely complete all as specified and as directed. Note : 1.Earth work paid seperately 2.Incase of pipe line is broken for takingup time new existing size of pipe line is laying by contractor in this quated rate

Taking up existing DI pipe line of size 150 mm removing old unserviceable Tyton joint (push-on-joint) and supply , fixing and testing of Tyton joint(push-on-joint) and relaying the pipe line completely complete all as specified and as directed. Note : 1.Earth work paid seperately 2.Incase of pipe line is broken for takingup time new existing size of pipe line is laying by contractor in this quated rate.

Removing old unserviceable starter any type and supply and fixing testing and commissioning of single phase submersible pump controlle, 230 Volt, 50 Hz with sheet metal enclosure with ammeter and volt meter, heavy duty suitable for 5 HP submersible pump including making connection with suitable size of copper cable, Relay range 20-32 Amp,start capacitor 275V,50HZ MFD and run capacitor 440 V,50Hz MFD complete all as specified and as directed. Make: L&T TYPE MR-G3 FASD HSN CODE 8536 CAT NO CS96167BEEJ

Fixing only cast Iron sluice valve 80 mm bore both end flanged,any patern with nut,bolts, washers and rubber gasket etc, fixed in replacement of existing u/s complete all as specified and directed by Engr-in Charge. Note:CI sluice valve shall be issued under schedule B

Fixing only cast Iron NRV of size 80 mm bore both end flanged,any patern with nut,bolts, washers and rubber gasket etc, fixed in replacement of existing u/s complete all as specified and directed by Engr-in Charge. Note:CI sluice valve shall be issued under schedule B

Fixing only cast Iron NRV of size 100 mm bore both end flanged,any patern with nut,bolts, washers and rubber gasket etc, fixed in replacement of existing u/s complete all as specified and directed by Engr-in Charge. Note:CI sluice valve shall be issued under schedule B

Fixing only cast Iron NRV of size 150 mm bore both end flanged,any patern with nut,bolts, washers and rubber gasket etc, fixed in replacement of existing u/s complete all as specified and directed by Engr-in Charge. Note:CI sluice valve shall be issued under schedule B

S & F Cast Iron sluice valve 150 mm bore both end flanged,long body,class PN-1.6 confirming to IS 14846-2000,duly ISI marked with hand wheel operated and Non rising stinless stem with gun metal parts flanges drilled to IS 1538 nut,bolts, washers and rubber gasket etc, fixed in replacement of existing u/s complete all as specified and directed by Engr-in Charge. Make : Zoloto Art no.1079B HSN code :84818030/ KIRLOSKAR

S & F Cast Iron sluice valve 100 mm bore both end flanged,long body,class PN-1.6 confirming to IS 14846-2000,duly ISI marked with hand wheel operated and Non rising stinless stem with gun metal parts flanges drilled to IS 1538 nut,bolts, washers and rubber gasket etc, fixed in replacement of existing u/s complete all as specified and directed by Engr-in Charge. Make : Zoloto Art no.1079B HSN code :84818030/ KIRLOSKAR

Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 15 of tender documents.

M/s JUGAL KISHORE MISHRA AND SONS

SRI SAI CONSTRUCTION COMPANY

SINGH ENTERPRISES