CONSTRUCTION OF TECHNICAL RECORD ROOM AT NAD TROMAY AND LAYING OF NEW 50MM HDPE WATER LINE AGAINST CONNECTION NO MWY 153004 AT TS MAHUL UNDER GE (NW) MANKHURD.

Amount

M & L Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out In Hard/dense soil.completed all as specified

Excavating in trenches, by mechanical means(hydraulic excavator) n exc 1.5 m wide and n exc 1.5 m in depth; for footing, Plinth Beam & Dwarf Wall, etc. n exc 10 sq m on plan and getting out in Hard/dense soil.

M & L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M & L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M & L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M & L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M & L Cement concrete in foundations, filling and mass concrete 1:4:8 using 40 mm graded aggregate (For Foundation)

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Hard/dense soil.

Removing excavated material in Hard/dense Soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M & L RCC- M-30 (Design Mix) using 20mm graded aggregate for Footing and plinth beams

M & L RCC- M30 (Design Mix) using 20mm graded aggregate for Column complete all as specified and directed

M & L RCC- M30 (Design Mix) using 20mm graded aggregate for beams and lintels complete all as specified and directed

M & L RCC- M30 (Design Mix) using 20mm graded aggregate for RCC Slab

M & L RCC- M30 (Design Mix) using 20mm graded aggregate for RCC parapet wall/drops/RCC Chajjas

S & F TMT bars 10mm dia & over of Grade Fe 500 incl cutting, bending, binding & placing in position with binding wirefor footings Slab beams roof slab etc complete al as specified and directed

Ditto but 5 to 10mm dia in stirrups, spacers & binders.

M & L Form work for rough finished surfaces of concrete measured flat for For Footing

M & L Form work for rough finished surfaces of concrete measured flat for Column,

M & L use & waste Form work for rough finished surfaces of concrete measured flat for Plinth Beam

M & L use & waste Form work for rough finished surfaces of concrete measured flat for RCC beams sides and soffits

M & L use & waste Form work for rough finished surfaces of concrete measured flat for RCC Slab

M & L use & waste Form work for rough finished surfaces of concrete measured flat for RCC drops/Chajjas

M & L Pre-cast cement concrete block masonry with solid blocks Type C1 1:3:6, exc. 10 cm in width and setting in Cement mortar (1:6) mortar, complete.

S& F factory made WPC solid door frames of size 65x100mm including fixing to walls using three numbers dash through bolt on each side as complete all as specified .and directed

S& F factory made single extruded WPC solid door shutters decorative type flush door of size 35mm complete all as specified and directed

S&F extruded aluminum alloy handles (150mm ) fabricated type anodised complete all as specified Make :- Shalimar / jyoti/ Classic/ Ashoka

S&F hinges (150 mm) stainless steel medium weight complete all as specified

S&F aluminum anodised barrel tower bolts (150 mm ) of extruded section complete all as specified

S&F 300 mm Aluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type ) and fixing clips of sheet , cast , exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified

S & F powder coated aluminium section as in frame / shutters for doors, windows, ventialtors with one or more rebates including joining cleat for fixing etc including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handles lock, rollers, Nylon bearing etc complete all as specified and as directed.

M&L for Ready mix plaster 12mm thick on faces of bricks or concrete surface including including preparation of wall surfaces etc complete all as specified and directed.

M&L for rendering 5mm thick in ready mix plaster on ceiling surface and finishing the surfaces even and smooth without using extra cement including scrapping down and preparation of ceiling surfaces to receive plaster, scaffolding as reqd etc, complete all as specified and directed.

M&L for Ready mix polimer modified cement based plaster 15mm thick on new bricks or concrete surface including preparation of wall surfaces etc complete all as specified and directed.

Material & Labour for applying two Coats Of Oil Bound Distemper Over One Coat Of Primer on Internal Wall

Material & Labour for applying two Coats Of Oil Bound Distemper Over One Coat Of Primer on ceiling

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additivesM @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M & L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L 75mm Thick Cement concrete ( 1:4:8 ) type D-2 (40mm graded aggregate)

Screed bed or bedding layer of mortar CM(1:6) 15 mm thick for laying floor finishes

M & L for coloured Non Skid ceramic tiles 8 to 10mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for Coloured Glazed ceramic tiles in vertical surface 350 x 250 mm x 7 mm / 450 x350x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over including rendering of 10mm thick inc CM 1:4 complete all as specified and as directed.

M & L 75mm thick Plinth Protection PCC (1:3:6) using 20mm graded aggregate over and including 75mm thick compacted hardcore.

M&L Water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a)Preparing & cleaning of fully dried cement concrete surface. (b) Applying one coat of hot bituminous primer to the plastered surface @ 0.25 litres per sqm conforming IS-3384. (c) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescribed by manufacturer to inaccesible roof.

Screed bed or bedding layer of mortar CM(1:3) 10 mm thick including mixing of WPC at the rate of 3% of weight of cment. Note : The WPC shall be measured and paid separately under relevant item.

Supply only Water Proofing compound

S&F aluminum anodised grill DG- 202 ( 10 mm x 5.2mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note : (i) Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

Supply only 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etc complete all as specified and directed

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

S&F in Godrej night latch 4 lever for entrance door with fittings complete all as specified and directed

M & L in for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth duly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws complete etc all as specified for one light / fan / bell point controlled by one switch. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. Make of conduit :- Sudhakar/ Precision/ Diamond, Make of wire :- Finolex/ Havells/ Polycab/ KEI

-Ditto- all as per item No 50 here-in-before but for one 6A 2pin/3pin socket out let multipurpose on the same board with other switches.

-Ditto- all as per item No 50 here-in-before but for one 6A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No. 50 above but wiring complete with 2.5 Sqmm for 3 pin 16A socket multipurpose on independent board

S & F modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed. Make: Schneider/GE/Legrand

S & F modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. Make : Schneider/GE/Legrand

S & F modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. Make : Schneider/GE/Legrand

S & F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. Make : Schneider/GE/Legrand

S & F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed. Make : Schneider/GE/Legrand

S & F Modular cover plate 4 modules complete all as specified and directed.

S & F Modular cover plate 3 modules complete all as specified and directed.

S & F ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed. Make : Schneider/GE/Legrand

Supply & Fix LED betten alluminium type fitting of capacity 20/22W, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 100 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long, housing made out of engineering plastic with decorative end caps elegently designed complete all as specified. Make - Bajaj/ Wipro/ Jaquar/ Halonix

S & F LED light fitting 1X10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make - Bajaj/ Wipro/ Jaquar/ Halonix

S & F Fancy Jumbo Batten holder metal ring suitable for LED bulb of 9 Watt complete all as specified and directed. Make - Schneider/GE/Legrand

S & F LED Light Bulb 9 watt, Pin type of white colour, 230 V complete all as specified and directed. Make - Bajaj/ Orient/ Philips

S & F MCB DB, 8 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete all as specified and directed.Make: Schneider/GE/Legrand Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB SPN 40 Amps, 240 / 415 Volts, 'B' Series, 50 Hz, 10 KA Breaking capacity complete all as specified and directed.Make: Schneider/GE/Legrand

S & F MCB SP 5 to 32 Amps, 240 / 415 Volts, 'B' Series, 50 Hz, 10 KA Breaking capacity complete all as specified and directed..Make: Schneider/GE/Legrand

M&L for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly complete all as specified and as directed Make:Havells/Finolex/Anchor panasonic Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 2.5 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly complete all as specified and as directed Make:Havells/Finolex/Anchor panasonic Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

Supply and fix high speed Ceiling fans complete with aluminium blades, down rods, PVC Canopy and accessories, white in colour 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value min 6.00, BEE Five star rated with brushless direct current motor(BLDC) without remote complete all as specified and directed by Engr-in-Charge. Make : Havells (Efficiencia Neo (BLDC 26 W) /Orient (FALCON 400) / Bajaj (ENERGOS 28)

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers complete all as specified and directed. Make :- ALMONARD / ORIENT

S&F of building Security light fitting 35 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge.Make: Bajaj/Jaguar/Halonix

S& F in GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45 degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge

M&L for earthing using GI earthing strip 32 x 6mm complete with galvanised steel earth plate electode 600mmx600mmx6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level connection to and including GI strip of size 32x6mm to the extend 7.5 mtr as earth lead by means of GI bolts, Nuts etc. with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I including water arrangement with GI Pipe 20 MM dia (medium Grade), earth lead protection pipe 50mm madium grade with bends, elbow etc. from earth plate to test point, excavation and earth work returning, filling, ramming and removing of soil to distance not exc 50mtr, make good to match with existing surface making PCC pit (Earth chamber) having internal size 30cm x 30cm x 30cm and outer size 60cm x 60cm x 60cm with RCC reinforced cover 50mm thick with one lifting handle made of 8mm dia MS bar funnel wie mesh and testing on completion including making test point on wall as per SSR specification all as specified and directed.

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil etc complete all as specified and directed.

M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified.Make: Mehtab Tiles/National

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10 Sqmm 2 core including necessary connection and providing cable lugs as required all as specified.Make: Havells/Polycab/Finolex

M&L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying GI tube ;returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:3:6; including removal of surplase soil all as directed by Engr-in-Charge..

S&F of HDPE pipe 75 mm dia, PN-10 for laying in ground, raod crossing etc for cable protection including necessary fittings, clamps for supports, etcall as directed by Engr-in-Charge.Make: Precision/Plasto/Supreme/Sudhakar

M&L for reinforced cement concrete nominal mix M-20 (using 20 mm graded stone aggregate) for foundations, including rafts, footings, foundation beams, plinth beams, bases for column etc and mass concrete, complete all as specified and directed.

Supply, laying, fixing, connecting, and testing of 50 mm bore High-Density Polyethylene (HDPE) pipes for potable water supply, conforming to IS 4984:2016, of PE 100 grade and PN 16 rating. The work includes pipe laying using butt fusion or electrofusion jointing or mechanical connection joint installation of all necessary fittings and valves, in any length, fixed to walls or laid in trenches, floors, or ducts. It also includes hydrostatic testing as per IS standards. All pipes and fittings shall be ISI-marked, non-toxic, and suitable for drinking water. The work shall comply with IS 7634 (Part 1):1975, IS 17425:2020, CPHEEO guidelines, complete all as directed by the Engineer-in-Charge. Makes: Finolex / Supreme / Dutron / Prince / Jain irrigation system / Plasto

S&F gunmetal gate or globe valve for 50 mm diameter, conforming to IS-778, Class 2, ISI marked, Copper alloy body, Test pressure (Hydrostatic) for shell 2.4 Mpa and Seat & back seat pressure of about 1.6 Mpa with maximum working temperature of about 45 °C with iron wheel head screwed at both ends for iron pipes or ferrule and fixing including necessary fittings like unions, check nuts, etc and any addition / alteration required for fixing, complete all as specified and as directed. Make :- Leader / Zoloto / L&T

Supply and fix in repairs Pressure gauge of 4" dial 0-14 kgs rating with ball valve including taking up / down old unserviceable pressure gauge from any position and any addition / alteration for fixing required including taking down old u/s pressure gauge complete all as specified and as directed. Make : Fiebig / H Guru / Baker Mercer

Supply and fix in replacement ladder height 10 feet max, steps on every 01 feet made of angle iron of size 50x65x5 mm thick for sump including taking down old rusted iron ladder complete all as specified and directed.

Supplying, fixing, jointing and testing in repair non-return valve suitable for GI tubing of size 80 mm bore size, (ISI Marked) both ends flanged and drilled for jointing including two flange joints and jointing material such as nuts, bolts washers rubber packing etc including taking down complete all as specified and as directed. Make :- Kirloskar, Upadhaya , Leader, Zoloto.

M&L for of valve pit of size up to 80 cm x 80 cm x 80 cm (internal diamension), stone / brick construction including all necessary excavation and earth work in any type of soil, returning, filling in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, PCC in foundation for mix (1:2:4) type D2 brick mansonary in cement mortar (1:4) rendering 12 mm duck in cement mortar (1:4) internally ,finished even and fair and polishing flush externally as the work proceeds in the same mortor. Mild steel angle iron 40 x 40 x 6 mm frame MS sheet cover 3.15 mm thick with handle and locking arrangement, painting all exposed MS work with two coats of synthetic enamel paint of the that as approved by the Engineer - in - charge over a coat of red oxide primer and painting all the MS embeded in PCC with two coats of black bitumenous paint complete all as specified.

S & F in repair cast iron Foot valve 65 mm, Ball type with flange joint model B-05 (N) conforming to IS with MS nuts bolts, washer, rubber gasket etc., any pattern as approved including taking out / dismantling old unserviceable one and testing complete all as specified and as directed. Make : KIRLOSKAR / UPADHAYA / LEADER

S&F in repair sluice valve 80 mm bore, cast iron body, flanged drilled end, conforming to IS-14846, ISI marked, class PN 1.6, reselient seating as well as metal seating Fusion bonded epoxy coating including all joints with rubber gaskets, bolts and nuts, washers, iron wheel including taking up / down old unserviceable valves from any position and any addition / alteration for fixing required complete all as specified and as directed. Make :- Kirloskar / Leader / Kartar / Upadhyay

S&F sluice valve 65 mm bore, cast iron body, flanged drilled end, conforming to IS-14846, ISI marked, class PN 1.6, reselient seating as well as metal seating Fusion bonded epoxy coating including all joints with rubber gaskets, bolts and nuts, washers, iron wheel including taking up / down old unserviceable valves from any position and any addition / alteration for fixing required complete all as specified and as directed. Make :- Kirloskar / Leader / Kartar / Upadhyay

Supply ,Laying, fixing, connecting and testing in repairs steel water tubing, medium grade, galvanised, with screwed and socketed joints, in any length, including supply and fixing all fittings, fixed to walls or laid in trenches / floors etc including taking out old u/s steel water tubing for the 25 mm bore complete all as specified and as directed , ISI marked. Make-: Tata/ Jindal/ BST/ Oswal

Ditto all as per item No 92 above but 50 mm dia bore complete

Ditto all as per item No 92 above but 65 mm dia bore complete

Ditto all as per item No 92 above but 80 mm dia bore complete

Note : A SUM OF RS 11696.00 TOWARDS SCHEDULE OF CREDIT SHALL BE DEDUCTED TO ARRIVE THE CONTRACT SUM

Parmatma Enterprises (BID ID -3463663)

HINDUSTAN BUILDERS (BID ID -3463796)

M/s Shree Construction Co (BID ID -3463436)

M/S KHUSHI ENTERPRISES (BID ID -3469139)

PRIME ENGINEERS (BID ID -3458921)